ok i just installed black diamond 3.1 and my phone hasnt loaded it yet i doesnt get past the second splash that says Black Diamond loading if it does i just has the little multicolored loading circle and goes nowhere ive tried hard reset it just resets it back to black diamond active sync wont connect can anyone help me?
nevermind its ok now
my troubles started yesterday after i flashed one of the roms here and it kept hard resetting everytime i soft reset. i flashed another rom and now it's stuck at the 'tap the screen to set up your windows phone' screen. it will hard reset but it's stuck at that screen no matter how hard i tap. (pretty soon i'll either crack the screen or throw the phone out the window)
any help?
it seems to work if i connect it to my pc via usb and allow activesync to connect at this screen. but why?
guys I am facing the same issue any solution for this???
I am very frustrated with my HTC Touch Diamond as I am trying to update it to Hard-SPL yet when it's plugged into the computer (with active sync running) and I follow all the directions very closely, I go to update the phone and it doesn't show any activity on the phone, the progress bar on my computer screen shows 0%, then it eventually pops up with a message saying Error 202. This is a connection error, yet I am positive that the phone is plugged into the computer. Add I have problem w align screen so I can't run anything od Diamond. Please HELP
Hello,
This is my first thread on XDA, because i'm having a problem with my Kaiser.
I'm sorry for my possible "silly" questions, but this a subject wich i'm not very good at.
I have a Kaiser, wich has a TPC Elite Rom Series
R 1.70.19.09
g 25.83.40.02h
d 3.28.00.00
And that runs on WM 6.5
Since last friday while i was configuring my mms settings, the device asked me to restart to assume the new settings. So i closed it down by pressing the power button until the message to "shut it down" appeared.
But when i tried to turn it on again, the device starts with the TPC Elite Rom Series screen, then it appears the data from the rom (mentioned above), then it moves to a screen with the Windows Phone message and logo and it stays here until i turn it off again.
So i cannot start my Kaiser and i need all the help i can get.
Thanks a lot to all of you that can give me a hand.
I already have done hard reset, but it keeps freezing on the "windows phone" screen.
try into three-colour screen and reflash ROM,or look here http://forum.xda-developers.com/showthread.php?t=423486
goodluck!
try into three-colour screen and reflash ROM,goodluck
this is also my first post here, can someone please help.
i tried to hardspl my htc kaiser, and failed miserably. i went through all the steps for hardspl but somewhere failed. during the setup when running the kaiser ruu file.on the cpu it said it was complete and for me to look to the phone to finish setup. on the phone it showed the linux penguin and a list of words scrolling down the screen. then it said error insert sd card. so i did then more words scrolled down the screen. then it said error again then the screen went black. after waiting an hour and nothing happened i took the battery out. then i tried to reload and the att logo would only show up. i read online how to get the tri colored screen back up and i got that by pressing the camera and power and reset button in.on the screen it says
kais1*0
spl-3.56.0000
cpld-8
and it doesnt respond to the computer. how do i re flash and get my phone working again someone please help if you can thank you
Hi, I'm new to XDA Dveloper. sorry if its already questioned..I don't have time to search for them, I'm running my laptop on battery that only will last about 15 minutes..and I have my electricity out..
Yesterday, I got My diamond exposed to water...it was raining hard and I was on my bike with my diamond in my pocket..
when I got home, my diamond begin to act strangely, it keeps lower its volume(to vibrate state) when I try to press the increase volume rocker, it goes back down to vibrate. but I manage to shut it down with slide2shutdown...and charge it (the battery only 7% left). this morning I get up and switch on the diamond, but It doesn't boot like usual(theTOUCHDiamond sceen)...
it only shows 4 bars (RED, GREEN, BLUE, and WHITE)consist of:
RED BAR with this:
DIAM100 64M
SPL-1.37.Olinex
MicroP-Diam (LED) v11
GREEN Bar with:
PSOC-Diam Stage_PVT v0x30
BLUE Bar : blank
WHITE Bar with
Serial (only "serial is written, nothing more)
That all, and when I try to connect with USB cable, it demands Qualcomm CDMA Drivers...(I use My friend's laptop....no activesync installed)
anyhelp would be appreciated.
thanks
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
bellsprout said:
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
Click to expand...
Click to collapse
what are you trying to hardreset device..??
A hard reset should only be performed if a normal reset does not solve a system
problem. After a hard reset, the device is restored to its default settings—
the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on your device will be lost. Only Windows Mobile® software and other pre-installed programs will remain.
Try flashing back to stock rom?
Sent from my GT-P1000 using XDA App
Hi!
I have a boot problem also.
I used Memo ROM about 1 month ago. That was worked well still today. I restarted my Diamond today, it was not boot correctly. Only reboot the phone after showing the ROM information. I made hard reset and put back the rom again, but the phone is not boot properly.
Could to help somebody for me?
I solved the problem.
I downloaded the original rom (included with radio rom) from htc.com.
I put the phone to bootloader mode and flashed this original ROM.
After flashing finished, my diamond boot to WM6.1.
I don't know what was the problem, but it works again...
I hope never happening this again!