Related
Everything works fine.
But i cant use activesync 4.5 to sync my contacts and so on
(i can install programes but it doesnt sync the conntacts.)
If i disable advanced network functionality the xda freezes
and the computer shows an unknwon usb device.
Can someone help me ?
Sorry for being a noob.
Everything is fine for me, are you sure that you flash the rom correctly as ordered ?
Sync problem
often can`t detect pda synchronitation . it`s show sync problem . Any way to fix it ?
I told you I don't have any problem which mentioned may be you have to reflash your rom, and start from the beginning.
Or first, you can delete your pairing connection with the pc, reinstall your active sync. And try to pair again. If you said "often", I hope this is not because of your hardware problem.
make sure your device is powered on ( the back light is on)..i also get it some time (only if i shut it by pressing Power Button at top)
Himalaya's USB Port is allergic to hubs
Don't try to use an USB Hub to connect the Himalaya to your PC. Always use a direct connection. This solved the problem for me.
...
Hi,
urbstar said:
Everything works fine.
But i cant use activesync 4.5 to sync my contacts and so on
(i can install programes but it doesnt sync the conntacts.)
If i disable advanced network functionality the xda freezes
and the computer shows an unknwon usb device.
Can someone help me ?
Sorry for being a noob.
Click to expand...
Click to collapse
Got exactly the same problem, since upgraded to WM6 (Tofclock Fresh ROM) Activesync never finds the PDA. Tried really everything possible, doesn't work. But 'cause there are some beautiful tools like WM5Storage or PIMBackup I don't care about ActiveSync.
May be its - as mentioned here - the USB Connection over USB Hub. But it's an internal one in my case so I can't proof.
And I don't think that the workaround for this problem is a ROM-ReFlash 'cause everything else works fine.
So long
HonkBB
i have same sync problem
i have upgraded from wm2003se to WM2006 AKU7.0 RAMDisk-40MB Pagepool size-24MB for Himalaya and everything is good but no activesync.
i have reflashed 4 times now and still no good.
any ideas???
newquaymarc said:
i have upgraded from wm2003se to WM2006 AKU7.0 RAMDisk-40MB Pagepool size-24MB for Himalaya and everything is good but no activesync.
Click to expand...
Click to collapse
Is your USB cable connected to a hub? This was the problem in my case (see above), but other users reported that it fails to when directly connected. Strange problem this is...
stupiddog said:
Is your USB cable connected to a hub? This was the problem in my case (see above), but other users reported that it fails to when directly connected. Strange problem this is...
Click to expand...
Click to collapse
cheer for reply but no cradle connected direct to my laptop
gonna have to go back to 2003 se till i hear of solution
shame xda runs great with wm6
I just want to ask you about active sync which version did you use ?
selangkahlagi said:
I just want to ask you about active sync which version did you use ?
Click to expand...
Click to collapse
thanks for replying
im using active sync 4.5 with xp pro all has been ok till this upgrade
I have the same with you, and everything is going well. May be you can try to delete the pairing both form your PDA and your PC and try to make new pairing again Good luck
selangkahlagi said:
I have the same with you, and everything is going well. May be you can try to delete the pairing both form your PDA and your PC and try to make new pairing again Good luck
Click to expand...
Click to collapse
cheers yes tried that.
im not happy with install anyway so will try again in a few days,
i think the unlock/unhide, doc tool did'nt work as i only got a formating msg
and still had my old splash screen and 14 odd me after the upgrade.
many thanks for your help.
will let ya know how i get on
newquaymarc said:
cheers yes tried that.
im not happy with install anyway so will try again in a few days,
i think the unlock/unhide, doc tool did'nt work as i only got a formating msg
and still had my old splash screen and 14 odd me after the upgrade.
many thanks for your help.
will let ya know how i get on
Click to expand...
Click to collapse
If you had old splash screen, big possibility you didn't do the last step
selangkahlagi said:
If you had old splash screen, big possibility you didn't do the last step
Click to expand...
Click to collapse
i did do it but dont think it ran correct, is it ment to run on 2003 se?
newquaymarc said:
i did do it but dont think it ran correct, is it ment to run on 2003 se?
Click to expand...
Click to collapse
did you do this step
hardreset your device.
Press ResetButton and hold down CameraButton + RecordButton.
Hold them pressed until the "Boot Options" menu appears on the screen.
Select the options as follows:
(for selecting use RecordButton, change values with CameraButton)
Enable KITL -> NO
Clean Registry Hive -> YES
Format Storage -> YES
When done, press DPad and wait until OS starts.
hi
yep done all that, NO-YES-YES i think the prep work before upgrade did'nt work..
maybe i need to goto wm5 then wm6, but wm5 was too slow for me to use.
a lot of laptops actually have one set of usb ports that are registered as a powered hub and often these don't really have enough power across all the ports... jst an idea...
active-sink!!!!!!!
hi all xperts,
lemme start with my Thanx to Tof the great and Helmi who have made this possible for the good ol' Hima..
Now i need some help -
I installed this package close to a month back with all instructions point by point.
Activesync was the problem..
Today i thot i'll increase the storage space - ran the unlock and then realised the Hima Doc tool is a exe file and i'll hv to have a valid activesync connection before i can get that worked.
Then i thot, i'll reload WM6.0
Again, started in Boot loader - Got the Serial Screen with v1.06 in bottom, connected my device to run the software -
I'm redoing the flash now - wish me luck guyz!!!!!!!!!!
Im so sorry, im not the kind of person that makes treads and post them as urgent. But this is truly urgent.
I have .net 3.5 cf installed on my phone, i then installed xbmod policy.cab and restarted. Disabled tf3d, installed XBmod VGA Rhodium Manila.cab, rebooted and installed HTC New Contact Card.cab. Once again i reboted, installed Start menu fix.cab and the reboted again. Then i enabled tf3d.
But it all crashes everytime! Manilla.exe crashes and gives a report
'Microsoft.VisualBasic recources not found.
Please im going away and i really need the phone to be working.
I also have sdkcerts installed and i have pressed the reset button with the stylus a couple of times
I would just reflash the ROM or try another ROM altogether that already has Manila 2 already on board. There are 2 in existence. One I am currently using and it works great.
First of all some background please.
Do u have Hard SPL already installed?
band27 said:
I would just reflash the ROM or try another ROM altogether that already has Manila 2 already on board. There are 2 in existence. One I am currently using and it works great.
First of all some background please.
Do u have Hard SPL already installed?
Click to expand...
Click to collapse
No, I have the 2..03.413.2 SVE room, the original from HTC.
Im to afraid to try cooked rooms.
pking said:
No, I have the 2..03.413.2 SVE room, the original from HTC.
Im to afraid to try cooked rooms.
Click to expand...
Click to collapse
then try again to install xboxmods rhodium manilla... well remember to go to settings>today and disable touchflo 3d before you install... then try installing it all again....
Arju007 said:
then try again to install xboxmods rhodium manilla... well remember to go to settings>today and disable touchflo 3d before you install... then try installing it all again....
Click to expand...
Click to collapse
Thats the fun part. Ive done that two times now :/
pking said:
Thats the fun part. Ive done that two times now :/
Click to expand...
Click to collapse
Many members went through this already. Learn from their mistakes ......PRESS HERE
If you have an original ROM then it may be that you don't have NET 3.5 Framework, yes?
yeah that must be it... lol ... hope that's his answer.. i remember my stock rom didn't have that but all the custom i've used has it cooked in..
Just go "Cooked" and you will never go back...lol
We can set up a day where I will help u through if you wish...
You know what. I will hard reset it.
Install xbmod policy.cab
Disable the plugin
Install XBmod VGA Rhodium Manila.cab
Soft reset
HTC New Contact Card.cab
Soft reset
enable tf3d today plugins
Is it all correct?
No i have .net 3.5 cf as i wrote in my first post.
Hey thanks man! but i have only had bad experience from cooked roms. And since my phone has gone in to service to get repaired 2 times i dont wat to risk getting a huge bill, you know they will make up that the rom was the one that destroyed the phone.
pking said:
You know what. I will hard reset it.
Install xbmod policy.cab
Disable the plugin
Install XBmod VGA Rhodium Manila.cab
Soft reset
HTC New Contact Card.cab
Soft reset
tf3d today plugins
Is it all correct?
Click to expand...
Click to collapse
No matter how many times you do this, it won't work without Netframework 3.5.
band27 said:
No matter how many times you do this, it won't work without Netframework 3.5.
Click to expand...
Click to collapse
I had installed this:
http://www.microsoft.com/downloads/...49-3C6B-42F1-9FD9-0041345B3385&displaylang=en
Does me having a swedish rom affect anything?
pking said:
I had installed this:
http://www.microsoft.com/downloads/...49-3C6B-42F1-9FD9-0041345B3385&displaylang=en
Does me having a swedish rom affect anything?
Click to expand...
Click to collapse
Regardless of what language your ROM is, will not impact your devices ability to install manila 2
pking said:
You know what. I will hard reset it.
Install xbmod policy.cab
Disable the plugin
Install XBmod VGA Rhodium Manila.cab
Soft reset
HTC New Contact Card.cab
Soft reset
enable tf3d today plugins
Is it all correct?
No i have .net 3.5 cf as i wrote in my first post.
Hey thanks man! but i have only had bad experience from cooked roms. And since my phone has gone in to service to get repaired 2 times i dont wat to risk getting a huge bill, you know they will make up that the rom was the one that destroyed the phone.
Click to expand...
Click to collapse
No, don´t softreset after installing VGA rhodium manila.cab - just hit continue or cancel (I don´t remember..) and proceed with the HTC new contact Card.cab. and then softreset.
This is from the installation instructions in post #3
Hope this helps..
jonorb said:
No, don´t softreset after installing VGA rhodium manila.cab - just hit continue or cancel (I don´t remember..) and proceed with the HTC new contact Card.cab. and then softreset.
This is from the installation instructions in post #3
Hope this helps..
Click to expand...
Click to collapse
No freaking difference. This has driven me mad.
My TYTN 2 (KAISER) came with the original WM6...But I upgraded/flashed it to WM 6.5 and that kinda sucks for me...
How can I revert it back to WM 6????
HELP.
Should I Hard reset it( by pressing several keys+stylus)??
Or should I hardSPL it again and flashing the WM6 Rom back??
rglive2008 said:
My TYTN 2 (KAISER) came with the original WM6...But I upgraded/flashed it to WM 6.5 and that kinda sucks for me...
How can I revert it back to WM 6????
HELP.
Should I Hard reset it( by pressing several keys+stylus)??
Or should I hardSPL it again and flashing the WM6 Rom back??
Click to expand...
Click to collapse
First of all this is Android development so this is very offtopic. Second you hopefully can find and download the correct WM version from HTC by entering your S/N. Then I think all you need to do is to hold camera button + reset the device to enter SPL, connect to computer with USB cable and then run the installation (that you downloaded from HTC).
Hi Kalit_Kaffe, Thnx for the Help. Was helpless...thts Y had to post it here.
Anyways...is the hard reset(holding camera button...the soft buttons and stylus) the same as Factory restore??...then i wouldnt be needing the file that you mentioned for download??
Am i right?
Reset to factory defaults will not replace the 6.5 rom you have installed, you don't need to HardSPL again, that only needs to be done once.
Your best option would be to get a stock rom from the XDA Wiki pages, My advice would be either get a shipped rom that matches your carrier, or the latest generic HTC shipped rom, both can be found here: http://wiki.xda-developers.com/index.php?pagename=Kaiser_ROMs
Note that once you flash a rom a Hard reset does not remove it, only flashing another rom will do that. Also flashing a stock rom is actually one of the best ways of clearing out previous flashes.
hi
Hey man thnx a lot! really helps!
HELP!!!!!!!!!
How do I install the USB driver for HTC TyTN II, to whom I am the Android 1.5. Before that I was a Windows Mobile 6.5 and am using Microsoft ActiveSync. I would like again to get back to WM 6.5, but can not seem to connect mobile phone and computer.
You can't flash back to Windows Mobile through usb while in Android because of the driver issues. You have to either enter bootloader mode and flash, or you have to do it through your storage card. And before you post back asking me how to do that, use the search. There are instructions all over the place.
thank you very much I was able through bootloader mode
does anyone know what is the best WM for HTC taytn 2? I am installing TPC_Kaiser_Titanium_Ultimate_28002, it's not something particularly good
There is no *best* ROM. Please read threads and flash based on your needs. I think it's about time this thread be done for.
rglive2008 said:
My TYTN 2 (KAISER) came with the original WM6...But I upgraded/flashed it to WM 6.5 and that kinda sucks for me...
How can I revert it back to WM 6????
HELP.
Should I Hard reset it( by pressing several keys+stylus)??
Or should I hardSPL it again and flashing the WM6 Rom back??
Click to expand...
Click to collapse
Looks like you need to downgrade your Hard SPL for WM6 so that it doesn't pause a lot.
http://forum.xda-developers.com/showthread.php?t=498320
Also there seems to be a guide for what you want. Sorry I stopped reading through the threads when I saw someone say you don't need to do anything with your hard spl.
http://forum.xda-developers.com/showthread.php?t=335568
Hi, if anyone could please help me i would be gratefull, i recently purchased a D2 but its already preloaded with WM6.5 rom version 2.53.405.5 (76952)WWE, But i really wanted WM6.1 as, among other things, i wanted to use the handwriting rec.
does anyone know what stock rom to reload? and where i can get it? sorry to ask such a basic question.
thanks in advance,
http://www.htc.com/europe/SupportDownload.aspx?p_id=249&cat=2&dl_id=613
thanks for that, however it seems to have just bricked the phone
thanks for that, however it seems to have just bricked the phone
it seemed to work, all the correct messages displayed
but......
now all that happens is it turns on, shows the touch diamond2 screen, then resets
it has the following text in red in the lower left hand corner
r 3 . 43. 25 .19
g 61. 20t. 25. 10U
d 1. 39. 47382
does any one have any ideas?
Try to hard reset.
tried that before i posted
and a soft reset, and another hard reset to be sure,
i searched the forum but couldn't find any reference to that type of error either.
any ideas on how to retrieve it from paperweight mode?
Download stock ROM for your region
Unpack it with WinRar or TotalCMD
Rename RUU_signed.nbh to topaimg.nbh
Copy topaimg.nbh on your SD card
Enter bootloader (hold volume down and turn on phone) and follow instructions
edit:I guess for wm 6.1 you need lower version of SSPL
thanks dude, i used the bootloader to reinstall the latest rom from HTC.
Topaz_S2_HTC_WWE_2.53.405.5_Radio_Signed_Topaz_61.44etc.25.35_4.49.25.91_Ship
my phone is no longer a brick however i am back to square 1 in that i still have wm6.5, and i want 6.1
ive tried to reflash with the older rom fighter7139 suggested
RUU_Topaz_HTC_WWE_1.39.405.3_Radio_Signed_Topaz_61.20t.25.10_3.43.25.19_Ship
but it gives me the same rebooting error.
any ideas why wont the older rom work on my phone? or if theres an alternative to that rom ?
thanks
I've loaded hardspl 1.83 and extracted the file RUU_signed.nbh and renamed it to topaimg.nbhand,
i moved it to the SD card, reflashed the phone with the 6.1 rom,
but i get the same error.
any idea on what rom i should use to update from?
or what stock spl i'd need to run this rom's version of 6.1 ?
a thought
maybe i don't even need 6.1, all i want to do is to fix two things -
1) make the sms messaging work like on the old htc devices ie diamond or tytn ie not use htc messaging
2) add handwriting recognition
- would also be nice to have the taskmanger icon, the battery icon and the original windows start menu back too, but im not dependent on them....
so i guess any rom would do that allows these functions, any help or info on this would be much appriciated
terminalkhaos said:
1) make the sms messaging work like on the old htc devices ie diamond or tytn ie not use htc messaging
Click to expand...
Click to collapse
Try http://forum.xda-developers.com/showpost.php?p=3771519&postcount=2991
2) add handwriting recognition
Click to expand...
Click to collapse
http://www.htc.com/www/SupportDownload.aspx?p_id=249&cat=0&dl_id=824
thanks for that, however that was the first thing i tried, i saw the download for the handwriting ap just after i got the phone, not knowing it didnt have it when i swapped from my diamond,
the thing is the update only works on certian AP version control builds -
the message on the site is -
Note: AP version control -> The criterion will pass if the Touch Input for Pocket is equal to Version 2.1 (Build1919.1320), or lower.
mines a higer version, which i assumed originally had to do with it being wm6.5 not 6.1,
- i have tried downloading and installing anyway but it wont load.
does anyone know how to get this update to load, or how to change the AP version control back to a lower version ?????
any help would be much appriciated.
if it matters,
i'm running Duttys HG, and ive flashed to hardspl,
i don't mind flashing back to whatever, i just really need the handwriting app
The handwriting SIP is likey hidden.
There is a reg edit to unhide, just search SIP Reg Edit and you should find it.
If I recall it was under the WM general tweaks.
thanks for that, i got the letter and block rec working, but still not the transcriber the reg key shows it should be showing, but i think the actual file may not be there,
fixed after changing the reg, and downloading the update, you then need this transcriber cab
http://forum.xda-developers.com/showpost.php?p=3661845&postcount=47732
result
Any luck finding a way to get 6.1 working on this phone? I just bought the Pure from AT&T as a replacement for my LG Incite that had 6.1 on it. So far I can't stand 6.5 at all. My main beef is with IE, I really like the one on my Incite vs. this one. And my other problem is with the start menu, I also prefer the drop-down style in 6.1.
Thanks for any replies or help.
TheNorthSideWhiteGuy said:
Any luck finding a way to get 6.1 working on this phone? I just bought the Pure from AT&T as a replacement for my LG Incite that had 6.1 on it. So far I can't stand 6.5 at all. My main beef is with IE, I really like the one on my Incite vs. this one. And my other problem is with the start menu, I also prefer the drop-down style in 6.1.
Thanks for any replies or help.
Click to expand...
Click to collapse
Start here.
Once you unlock your phone, you can flash to anything you want.
6.5 is hands down better than 6.1, there are 6.5.219xx builds that have the drop down start menu.
Thanks Bruce!
For some reason I couldn't find a good Pure forum, so that link helps a lot.
Please, I tried loading Android on my At&t Tilt, and it wasn't successful, so I decided to switch back to Win 6.5, but could not load beyond
"Smart Mobility"
R 1.70.01iNex
G 25.65.30.04H
D 1.56.00.00
Please, I'll appreciate your help and concern. I've spent more than 10 hours trying to fix it using most of the thread posts.
I will love helpers to be specific on how to change back to win 6.5, and the complete tools for making android work on it.
I will also love someone who can help me through chat page on facebook or yahoo. My id is tundelogic for both. Thanks in anticipation and God bless you.
If I understand correctly, you've installed Android into NAND and later WM 6.5. In this case you must firstly install original WM 6.1 and only then WM 6.5
Infosoft.lt said:
If I understand correctly, you've installed Android into NAND and later WM 6.5. In this case you must firstly install original WM 6.1 and only then WM 6.5
Click to expand...
Click to collapse
I tried installing android, but it didn't install, after much trial, I felt switching back to WM ROM will work for me.
Please, don't be annoyed can u please post links of all I'll need to get my phone back to WM 6.1. i.e
Hard SPL to be used, Radio to use and Rom to use. I appreciate your response. Thank you.
> HardSPL 3.56 (force USB) / or you can use 3.34
http://forum.xda-developers.com/showthread.php?t=498320&highlight=Hard+SPL+3.56
> Radio 1.71... (actually I've never had any problems with other versions, but 1.71 is the newest).
http://forum.xda-developers.com/showthread.php?t=393182&highlight=Radio (post #3)
> Official WM 6.1
http://forum.xda-developers.com/showthread.php?t=439408&highlight=Kaiser+WWE+6.1
Because there were some problems for you while trying to flash Android, I recommend firstly to enter bootloader (hold Camera + Power buttons together and reset with stylus (button for reset is near miniUSB port; just put stylus in it and push for a few seconds); you'll see tri-color screen with SPL version...), then connect it to computer and finally run WM 6.1 EXE file (in case you're using Windows 7, set file compatibility mode to XP <- I'm not sure if it's necessary).
Thanks I'll get back as soon as I'm successful. Please, if you won't mind, can you please give me your chat id, so that if I have any issue, I can reach you quickly. Thanks once again. Y! [email protected].
If you'll need my help: http://www.facebook.com/Vytautas.Baciulis
Please I need someone to upload prepared files needed for Android, as I've tried preparing with aTools, following the tutorial without success.
tundelogic said:
Please I need someone to upload prepared files needed for Android, as I've tried preparing with aTools, following the tutorial without success.
Click to expand...
Click to collapse
You can get the files needed to run the android and guide at http://forum.xda-developers.com/showthread.php?t=680518