Related
I REALLY NEED HELP...
i was updating the rom to 2.21 and i guess i accidently closed the program.. sooo now my phone turns on to this screen.. it shows 3 colors.. i can not do anything..
i really need help.. what can i do to go back?
Ok, there's a chance that you just turned your phone into a nice little paperweight however, I recommend trying two things. First, try to perform a hard reset by following these steps:
1: Press and hold both the Comm Mannager Button and the Voice Command Button
2: While keeping those two buttons pressed, press the Reset Button with your stylus
3: After about a second you will be prompted for confirmation. Press the Talk Button to confirm
If that fails, try performing the ROM upgrade again. If THAT fails...well either my assumption is correct or you're gonna need someone more proficient than me to help you ^_^
i tried doing that.. that didnt work..
when you try to install the rom again.. the phone has to be connected with active sync.. and right now its not.. but if u look at the screen on the phone.. it says usb.. but it doesnt connect..
so idk what to do now..
i have another mda..
this one has the original ROM and it works.. is there anything i can do?
please help
harut9161 said:
i tried doing that.. that didnt work..
when you try to install the rom again.. the phone has to be connected with active sync.. and right now its not.. but if u look at the screen on the phone.. it says usb.. but it doesnt connect..
so idk what to do now..
i have another mda..
this one has the original ROM and it works.. is there anything i can do?
please help
Click to expand...
Click to collapse
If you have the bootloader screen(rainbow) it should be retrievable.
Just to be sure you enter the bootloader screen hold camera button and turn on.
The device should be able to connect to your pc, but not by activesync.
If it wont try disabling any firewalls or antiviral on the pc and try again.
Once the pc recognizes your device - run the rom upgrade again.
Fan-freaking-tastic!!!!
Thanks meschle !!!!
I had loaded a cingular rom onto a tmobile thinking all HTC roms should work alike (i know idiot sign is already on my forehead) and the phone was working but very slowly and sync did not work...
I checked and I could get to the bootloader screen (rainbow) as you suggested and then was able to load the original firmware just fine... Phew.. Saved my having to explain a $500 brick to folks.. lol
I have a question on this however, if I want to upgrade the radio or something other than T-MOBILE rom.. what do I need to look for to be sure it will work on my T-MOBILE ?
Cheers
and Thanks
I dont know what to do... Yesterday i flashed my wizard to wm6 mb rom, everything worked great but today, couple hours ago i tried to upload some stuff by activesync, suddenly pda disconnected and hanged, so softreset and nothing - its stuck on bootscreen where there is info about my components:
ipl 2.26
spl 2.26
gms 02.61.11
os 3.3.0.0 (was something like 10.xxx... but i flashed faria 3.5aku and now is 3.3)
i also tried to format but msg FormatFailed appear :/
it is possible to run in bootloader and charger also charge my wizard
what to do ????
Do you have a copy of the Wizard Love rom? If so, install that in bootloader mode. Remember to plug your USB cable into the phone.
drivex said:
I dont know what to do... Yesterday i flashed my wizard to wm6 mb rom, everything worked great but today, couple hours ago i tried to upload some stuff by activesync, suddenly pda disconnected and hanged, so softreset and nothing - its stuck on bootscreen where there is info about my components:
ipl 2.26
spl 2.26
gms 02.61.11
os 3.3.0.0 (was something like 10.xxx... but i flashed faria 3.5aku and now is 3.3)
i also tried to format but msg FormatFailed appear :/
it is possible to run in bootloader and charger also charge my wizard
what to do ????
Click to expand...
Click to collapse
i am after updating and still wizard hangs up on boot screen. versions has changed and bootscreen logo too, what now ? ;((((
drivex said:
i am after updating and still wizard hangs up on boot screen. versions has changed and bootscreen logo too, what now ? ;((((
Click to expand...
Click to collapse
I would suggest flashing back to a carrier aku2.x rom and ensure that your phone will come up properly on it. If it does then good, it's most likely not a serious hardware issue, if not then you might be out of luck.
looks like a brick to me..
So sorry m8.
I hope you can revive it !
Had similar problem with the Super rom.What worked for me was taking a back up on the memory card and reflashing from the card.Read the Wiki about details on how to go about it.
Try to flash the latest t-mobile ROM found on their site if all the suggested doesnt work..
@ DRIVEX
Try Hard resetting via the harware Buttons Softreset hole method. Here is how:
----------------------------------
While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key.
Hope it helps.
.
I've done. I used method with mtty and i copied os to sd card, after that i reflashed using minisd card and it works. Thx for everyting, u guyz do great job here hehe
Me too !
cyberdrakula said:
@ DRIVEX
Try Hard resetting via the harware Buttons Softreset hole method. Here is how:
----------------------------------
While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key.
Hope it helps.
.
Click to expand...
Click to collapse
I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...
Pls help me !!!
cachep2004 said:
I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...
Pls help me !!!
Click to expand...
Click to collapse
this is dead your flashrom chip in pda. repair only change semiductors or all board.
Pls show me another ways !
UfOuN said:
this is dead your flashrom chip in pda. repair only change semiductors or all board.
Click to expand...
Click to collapse
I'm living vietnam, so i'm trying to find out another ways, but i think they have no equipments.
Bless god for me.............pls
Revive Wizard
you must use youre camera button on the startup if you got error 260.
You see a lot of collors on youre display and then you can flash youre phone again.
Thanks alot !
sleurhut said:
you must use youre camera button on the startup if you got error 260.
You see a lot of collors on youre display and then you can flash youre phone again.
Click to expand...
Click to collapse
Thanks alot my friend, I will do it !
"FORMAT FAIL" again again pls ... help me !
( I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...)
Pls ! Help me...."FORMAT FAIL" again again pls ... help me !
The hard reset doesnt work
I cant even get the screen to go on anymore. When I plug it in the light doesnt even go on to indicate that it is charging. SOmeone help me please.
ecomajor said:
I cant even get the screen to go on anymore. When I plug it in the light doesnt even go on to indicate that it is charging. SOmeone help me please.
Click to expand...
Click to collapse
Hard to help someone that hasn't told us anything.
From the sounds of it your battery has died. Until you get a good rom on there, the phone will NOT charge. You will need to find someone with a similar phone (or maybe go to your cell provider) and get them to charge the battery at this point. Once you have the battery charged then try following this step by step:
http://forum.xda-developers.com/showthread.php?t=298613
If that doesn't work, then come back and tell us more about what happened, what your IPL/SPL is, what type of phone you have, if its G3 or G4, etc... People here will help, but not without information.
mfrazzz said:
Hard to help someone that hasn't told us anything.
From the sounds of it your battery has died. Until you get a good rom on there, the phone will NOT charge. You will need to find someone with a similar phone (or maybe go to your cell provider) and get them to charge the battery at this point. Once you have the battery charged then try following this step by step:
http://forum.xda-developers.com/showthread.php?t=298613
If that doesn't work, then come back and tell us more about what happened, what your IPL/SPL is, what type of phone you have, if its G3 or G4, etc... People here will help, but not without information.
Click to expand...
Click to collapse
I have G3. i think its 2.25. I was trying to flash my rom when this all happened.
is there any way to charge it without a good rom?
ecomajor said:
I have G3. i think its 2.25. I was trying to flash my rom when this all happened.
is there any way to charge it without a good rom?
Click to expand...
Click to collapse
Not that I know of. Thats one of the reasons its recommended you start with a battery that has over 50% charge (personally I never flash with less than 100% in case something goes wrong). Not saying you didn't do that, but you appear to now be trying to work with a dead (or almost dead) battery, and that will only make things worse if you try to flash and then the battery dies in the middle (maybe not worse, but it sure won't help).
Like I said, you'll need to find someone with a similar phone or see if your local cell provider office will let you charge it (or swap it for a charged battery).
I got my ppc back up and I tried reflashing again and I have almost the same issue. It says format is successfull but then it gets stuck at the blue screen.
I have a stuck image on my 8125. The phone "boots" but only shows a white screen, and is unusable.
The "a2sd all" restore option mentioned in the forums doesnt work for me. I have read on several forums that I should be able to reflash the OS from the bootloader, though I cant find any instructions on how to do this
Could someone point me in the right direction for how to flash an OS VIA bootloader?
Thx
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Mirek - not to be totally ignorant, but the step 4 is what I'm having problems with .... where can I find either a providers ROM, or something that I can actually use while in bootloader mode?
Thanks!
NM ... Found it!
For anyone reading this .... You can get the provider ROM for the 8125 from HTCAmerica here: http://www.htcamerica.net/support/8125/software-downloads.html
Thanks for your help!
mirekluza said:
1. Get the phone to bootloader (tree color mode) - I think by soft resetting and pressing the camera button at the same time
2. Connect it to the computer (Windows XP) with a USB cable
3. You will notice "USB" written in a lower corner of the phone (this means it is connected)
4. Now you can flash your provider's ROM without any problems
I am not sure whether the bootloader flashing is possible from Windows Vista.
You must flash normally (in bootloader you cannot use either shelltools or SoftSPL - so use your provider's ROM).
Mirek
Click to expand...
Click to collapse
Dear Readers,
I'm having problem with my Dopod 900(,Qtek 9000,HTC Universal,O2 Xda Exec,Jasjar ). Can somebody please tell me what to do?
Before this, every time somebody called, the PDA lost the network bar and start to search or network and reject the calls automatically and also i wasn't able to send SMS. Now, i tried to install WM6 crossbow, the phone even cannot be on !!! even when i connect it to the charger, even the light will not be on. the only page that i can see is a white page asks Press 0 to Restore factory default or press X to exit. either perss 0 or X, the phone will be off and i cant turn it on with power key....
Please tell me what can i do ?? I really need your help.
PLEASE REPLY, PLEASE.
[email protected]
Warm Regards to All
G-Jorji
brick?
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
WHAT did you downgrade from?
Did you re-unlock your G3?
How's your battery?
acuraholic said:
hey guys, i need a little help. i downgraded my phone to buttons rom and then i was gonna attempt to upgrade the ipl/slp to 2.xx. so i downloaded the wizard ipl/spl 208 from the ftp site. i had a successful flash but when it went to reboot, my wizard never turn on again. ive searched the forums but it seems to me i have a brick found nothing. has anyone had the same situation happen to them? and find a solution?
it wont turn on at all anymore
Click to expand...
Click to collapse
IPL/SPL 2.08? Does that exist? Do you mean 3.08?
Are you sure your device is a G3? Or you killed it when flashing Button's ROM?
After I get out my diamond from my pc and than turned off it cannot start, it stoods on screen when it shows me version of my radio and ROM. I know that I have to do hard-reset but i dont want to, because i were so dumb that I dont backed up my mdata and programs which Ihave installed in Memory. Is there any chance to turn it on without the hard-reset???
Thx in advance.
betacheer said:
After I get out my diamond from my pc and than turned off it cannot start, it stoods on screen when it shows me version of my radio and ROM. I know that I have to do hard-reset but i dont want to, because i were so dumb that I dont backed up my mdata and programs which Ihave installed in Memory. Is there any chance to turn it on without the hard-reset???
Thx in advance.
Click to expand...
Click to collapse
do you mean bootloader (Tri-Coloured Sceen) Or the splash screen (Black Screen with touch diamond on it)?
I suggest you do a hard reset, and check this thread on how to easly back up ur programs, settings and manila config for future use using SASHIMI
http://forum.xda-developers.com/showthread.php?t=538513
Stuck in Bootloader screen
Whlie trying to upgrade the ROM on my Touch Diamond something happend so i got an error and the upgrade stopped. Now i cant continue the upgrade becouse my pc wont recognize the phone when i connect it with the usb-cabel. When i try to run the upgrade again i just get an error saying that there is something wrong with the connection.
I have tried hard reset but nothing works.
Hope someone can help me with this problem.
Thanks
/Kenneth
KenOslo said:
Whlie trying to upgrade the ROM on my Touch Diamond something happend so i got an error and the upgrade stopped. Now i cant continue the upgrade becouse my pc wont recognize the phone when i connect it with the usb-cabel. When i try to run the upgrade again i just get an error saying that there is something wrong with the connection.
I have tried hard reset but nothing works.
Hope someone can help me with this problem.
Thanks
/Kenneth
Click to expand...
Click to collapse
i think I am in same situation. phone is bricked :/
I dont think your phone is bricked, put your phone into bootloaded mode, connect phone to pc and flash the nbh file using CustomRUU. That should fix things
Dom1n8tr1x said:
I dont think your phone is bricked, put your phone into bootloaded mode, connect phone to pc and flash the nbh file using CustomRUU. That should fix things
Click to expand...
Click to collapse
each bootloader i have tried using the different hard spl version gets as far as the progress bar but fails at 0% with 262 connection error. tried about 6 different hard spl, signed unsigned olinex, customRUU. each of them all fail at 0% of progress bar.
will try it again today.
sorry betacheer for the hijack, but hope this helps you out in some way too.
yesterday i installed the rom of one of the above threads (win 6.5.28052) but everytime i boot up my device (when it is installed) it crashes.. constantly the same screen and i cant do anything?
i wanted to flash it to another win 6.5 rom. but i cant even turn on active sync on my phone
can anyone help me?
and fast. because i cant call and sms..
oh and: sorry for bad english
One post below is an exploit that seems to work without activesync, You could try this : http://forum.xda-developers.com/showpost.php?p=5336477&postcount=379
If I`m right it should connect again after You have a new SPL onboard. Relatively new here myself...
Another method would be to flash directly from an old SD card (not a new micro with adapter).
Edit : Maybe I misunderstood "turn on active sync on my phone" : Are You trying to flash when in bootloader mode (tricolor screen) ?
i was not flashing my phone in tricolor screen. but i did saw that screen when i installed the new rom?
but how do i come in the bootloader?
EDIT: can u please explain me in steps how i have to do this? (i am not so smart in those things..)
and how do u flash with a SD card?
another EDIT: i came a little bit further. no i see the commanager screen and disabled everything, then i tryed to turn on active sync. but then it freezes I WANT TO USE MY PHONE AGAIN!
Where did you find 28052 for trinity?.
Bootloader mode push on+camera botton+soft reset.
it was an older version.. typed it wrong. it was 28014..
but do u have a clue how i can fix this?
EDIT: now if i unlock my device. i get the windows screen when it boots up and does nothing.. so i cant do even less..
Ths to Supersport:
My recommendation for Flashing is:
Make sure you have Hard SPL on your Phone. I recommend Olipro 1.20 - Click Here for More Info
Be sure your battery is at least 50% full.
Start your phone in Tri Color Screen mode. Steps below
--Unplug your phone from USB
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
--Plug in the USB cable (if asked about installing a driver, do this), You should see USB in the White Box)
Now you can Flash.
And take a look also here:
http://forum.xda-developers.com/showthread.php?t=576880
Bye
atropo said:
Ths to Supersport:
My recommendation for Flashing is:
Make sure you have Hard SPL on your Phone. I recommend Olipro 1.20 - Click Here for More Info
Be sure your battery is at least 50% full.
Start your phone in Tri Color Screen mode. Steps below
--Unplug your phone from USB
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
--Plug in the USB cable (if asked about installing a driver, do this), You should see USB in the White Box)
Now you can Flash.
Click to expand...
Click to collapse
that tricolor screen says:
TRIN100
IPL-0.50
TRIN100
SPL-1.20.Olipro
so the spl version is good?
what to do next?
EDIT: what happens when i reset everything to factory standard?
ok. i did the steps u gave and i am flashing now..
now see what it does..
ow and btw.
how u can do dual boot on this phone? maybe i want android on it if it is possible
where can i find a good version of windows mobile 6.5? becuase the version i have now i dont like.. but the other version i tried was wrong?
Glad You found some help, I currently only have internet access at work...
What a good ROM is depends on Your liking. If You want a clean 6.5 base to install stuff Yourself and have lots of free RAM for bigger apps, check the second post of
http://forum.xda-developers.com/showthread.php?t=551424
The one my phone came with was also from xda-devs but couldn`t run iGO (nav software) because there was too little free RAM, too much preinstalled stuff running like Manila eyecandy...
So if You want a ROM with fancy today screens and other preinstalled stuff You`ll have to take a look around here, otherwise check the one above, many ppl recommend it.
Happy flashing
@flyby.
i dont like the standard skins of windows mobile 6.5 but i like the start menu and the file explorer thing,
and i used SPB Mobile before and i like that!
but what is the lightest version of windows mobile 6.5 here on xda? without that fancy touchflo etc, only the good start menu in the top and a good file explorer were u can scroll with u finger?