Cyanogen wiki says 2.22.23.02 radio for T-Mobile/US, 2.22.19.26i for Non US. But does the US/non US refers to the phone or the user? I am buying a T-Mobile G1 for use in New Zealand. Which one should I flash?
It really doesn't matter. I use .02 on 02-UK (ignore that my phone's a sapphire) and the signal strength has marginally improved over 26i. Try both and see which works best for you.
Doesn't matter. 2.22.19.26I was the old radio. And yes it works for people in the USA and out of USA as well.
sent from my superfroyo dream
Related
Hi all,
Ive seen a few threads opened up but redirected to the radio thread with no answer.
Im pretty technical and have gone through a few phones. Ive got a Kaiser now and im in Australia on Telstra.
The threads that i have seen detail how if you are Telstra customer and are on a newer radio people you are talking to get your voice FADING in and FADING out
Can you assist?
Cheers
Anthony
bump - what no one has come across any fade issues?
Nah, none of us are daft enough to use telstra
Seriously though - I'm with three, never heard of this issue with the tytn. Theres a 1.70 radio available at HTC HongKong e-Club or through the Kaiser ROM thread, its easy to flash/upgrade - just connect your cable & run the exe. Maybe that'll help ?
test7875 said:
Hi all,
Ive seen a few threads opened up but redirected to the radio thread with no answer.
Click to expand...
Click to collapse
I take it that means your flashing to the ROM I referred you to (detailed in your post on the ultimate radio thread at 11.38 yesterday) means the WWE Hong Kong ROM/Radio/SPL upgrade both I and snachez referred to has made no difference? If you've not been able to flash that ROM yet, give it a try first and let us know how you get on.
Update :
Flashed to HK SEA Radio 1.70.19.09
Certainly better than 1.71.xx.xx but still not 100%
Hmmm - i dont think im going to get much traction out of the new polaris roms but ill give it a shot and report back
test7875 said:
Update :
Flashed to HK SEA Radio 1.70.19.09
Certainly better than 1.71.xx.xx but still not 100%
Hmmm - i dont think im going to get much traction out of the new polaris roms but ill give it a shot and report back
Click to expand...
Click to collapse
Did you try the accompanying HK WWE ROM and HTC SPL 3.34 (the complete package) as well? If you have and you're still having probs then given that this combination has been found to work OK with at least one other Aussie network (from reports here at xda-dev), it's time to complain to Telstra and see what they have to say.
Flying Kiwi said:
Did you try the accompanying HK WWE ROM and HTC SPL 3.34 (the complete package) as well? If you have and you're still having probs then given that this combination has been found to work OK with at least one other Aussie network (from reports here at xda-dev), it's time to complain to Telstra and see what they have to say.
Click to expand...
Click to collapse
No i havent tried the complete package.
The problem is Telstra is unique with their nextG UMTS 850 network and as they didnt bring in the Kaiser to Australia they would laugh at you if you asked any questions (trust me i have some inside knowledge )
Its back to trying different roms.
i am in Au with telstra gsm (not 3g though) and have used multiple roms/radios with no issues with calls.
KC
test7875 said:
No i havent tried the complete package.
The problem is Telstra is unique with their nextG UMTS 850 network and as they didnt bring in the Kaiser to Australia they would laugh at you if you asked any questions (trust me i have some inside knowledge )
Its back to trying different roms.
Click to expand...
Click to collapse
So given all the other feedback, will the complete SEA WWE ROM package be the first? Maybe someone with the ROM can verify whether the Connection Wizard lists Telstra as an option under Australias network options...
Hmmm if it comes to dire straits ill load the entire rom as suggested but the history of this phone and my gut tells me the problem is specific to the Radio ROM.
What ive learnt
This is only a Telstra NextG issue (not seen on optus/voda/3).
Specific to the 850UMTS band
Niki and Emo Radios similar results.
Im currently testing the new polaris Radio 1.59.44.02 and so far with better results. Its only been a day so far so ill post back ... again!
Telstra Kaiser owners feel free to bump this...
I don't have a Kaiser but a Polaris with Telstra and that runs fine @ 850 mhz with Polaris radio 1.59.44.02
Crystal clear reception and no fade in/out.
I believe the hardware in our two devices are similar/identical, so I don't think it's a network issue - I think you are on the right track trying different rom/radio combinations until you find one that works best. Good luck.
cr1960 said:
I don't have a Kaiser but a Polaris with Telstra and that runs fine @ 850 mhz with Polaris radio 1.59.44.02
Crystal clear reception and no fade in/out.
I believe the hardware in our two devices are similar/identical, so I don't think it's a network issue - I think you are on the right track trying different rom/radio combinations until you find one that works best. Good luck.
Click to expand...
Click to collapse
Your spot on .. POLARIS radio 1.59.44.02 has had the best results out of all so far.
People report they get the odd crackle but no fade in and or out.
What does HTC Australia say?
Hmm, given HTC have a presence in Australia and their recommended Radio for the TyTN II sold there currently shows 1.65.16.25 on their website (the one that gave me next to no GPS functionality when released here for UK customers), how has anyone done getting an official HTC solution to this problem with the TyTN II and the Aussie Telstra network? Is HTC Australia even aware of the problem? I hope they are more responsive that HTC here in the UK.
Flying Kiwi said:
Hmm, given HTC have a presence in Australia and their recommended Radio for the TyTN II sold there currently shows 1.65.16.25 on their website (the one that gave me next to no GPS functionality when released here for UK customers), how has anyone done getting an official HTC solution to this problem with the TyTN II and the Aussie Telstra network? Is HTC Australia even aware of the problem? I hope they are more responsive that HTC here in the UK.
Click to expand...
Click to collapse
As far as I know there is no HTC Australia - only an importer. All of the HTC support for this region is run out of Asia, and in my experience, not too flash.
I've been using a TyTn II all year on the Telstra Next G network for my business (average 20 calls a day) and have flashed a few roms in that time but have never had anyone complain about sound quality with any of the Roms I've used. I use a Jawbone 2 bluetooth headset most of the time and I'm currently using the 3.34.721.2 WWE Rom with the 1.70.19.09 Radio and HardSPL 3.29 hard2 and can't recommend it highly enough, battery life is brilliant !!!
Hope this may be useful info.
I thought I could just follow a standard tutorial for getting Cyanogen on my device, but then I was horror stricken to see this tutorial which Rogers Dream users are supposed to use:
http://wiki.cyanogenmod.com/index.php/Full_Update_Guide_-_Rogers_Dream_EBI1_to_CyanogenMod
First off the bat, I am using my dream unlocked on the Bell network, which is only WCDMA 1900mhz. So I don't know if doing this will stop the device from using HSPA over EDGE, because I don't know what's being changed in the radio version. If it changes to EDGE then I'm screwed because Bell being WCDMA doesn't support EDGE.
The tutorial is discussing keeping an EBI1 kernel for that radio but then mentions a EBI0. I have no idea what affects this will have on my device running unlocked at 1900mhz with the non stock carrier.
Also, this is probably stated in a million different threads, but how can I be assured that this guide is infact for my device. I guess I'm trying to ask what must I check to assure this will work on my device?
I would recommend using the guide at that link because of the reasons listed at the beginning and your phone will remain closer to how it came (mainly radio version).
Macmee said:
First off the bat, I am using my dream unlocked on the Bell network, which is only WCDMA 1900mhz. So I don't know if doing this will stop the device from using HSPA over EDGE, because I don't know what's being changed in the radio version. If it changes to EDGE then I'm screwed because Bell being WCDMA doesn't support EDGE.
Click to expand...
Click to collapse
If you use the guide on the wiki the radio stays the same so there shouldn't be any problems. haykro's method uses the radio from the T-Mobile G1 and it is really unknown what the differences are but some slow data speeds have been reported. I haven't heard of anyone that can't connect to networks on certain frequencies due to the radio version, this seems to just be hardware based.
Macmee said:
The tutorial is discussing keeping an EBI1 kernel for that radio but then mentions a EBI0. I have no idea what affects this will have on my device running unlocked at 1900mhz with the non stock carrier.
Click to expand...
Click to collapse
It only says that you won't have a EBI0 radio.
Macmee said:
Also, this is probably stated in a million different threads, but how can I be assured that this guide is infact for my device. I guess I'm trying to ask what must I check to assure this will work on my device?
Click to expand...
Click to collapse
This should work for any Dream purchased through Rogers and has Rogers stamped on the back. You can check the radio version in the settings under about phone. It should be 3.22.20.17. You can also check the SPL version in fastboot (power on while holding camera). If you have 1.33.0009 you have the original SPL, if you have 1.33.0010 you have the new "perfect" one and you will have 1.33.0005 after rooted.
And a couple of questions for you. How did you get your phone unlocked? How is the GSM with Bell and did you get a better price than Rogers?
beav_35 said:
I would recommend using the guide at that link because of the reasons listed at the beginning and your phone will remain closer to how it came (mainly radio version).
If you use the guide on the wiki the radio stays the same so there shouldn't be any problems. haykro's method uses the radio from the T-Mobile G1 and it is really unknown what the differences are but some slow data speeds have been reported. I haven't heard of anyone that can't connect to networks on certain frequencies due to the radio version, this seems to just be hardware based.
It only says that you won't have a EBI0 radio.
This should work for any Dream purchased through Rogers and has Rogers stamped on the back. You can check the radio version in the settings under about phone. It should be 3.22.20.17. You can also check the SPL version in fastboot (power on while holding camera). If you have 1.33.0009 you have the original SPL, if you have 1.33.0010 you have the new "perfect" one and you will have 1.33.0005 after rooted.
And a couple of questions for you. How did you get your phone unlocked? How is the GSM with Bell and did you get a better price than Rogers?
Click to expand...
Click to collapse
If I have 1.33.0009 does that mean I can use a method that doesn't risk bricking? It says when I flash the SPL it can brick the device
No, im sorry there is always a possibility of bricking a device when flashing firmware. If you follow the directions to the dot and verify the md5 sum of downloads the risk of bricking should be low. If you want to root it is a risk you are going to have to take just like flashing the firmware of any device (BIOS, etc.)
Beav_35:
I also am using an unlocked rogers dream on Bell.
Notes:
I called Bell with the IMEI before I bought it and asked them if it would work. They said yes.
I unlocked by purchasing a code from an ebay seller. $6. Two hours to get it. Worked for me, twice.
The roaming setting must be enabled. The status symbol has an R in it even tho I am not really roaming. Not a big problem for me.
There is an H in the data symbol. It works OK. The browsing speed is quick (this is a relative term) when tethering but molasses when using the browser in android. Not really sure what this means but it is better than the Treo650 I was using.
I just use Bell because I have contract and it is an acceptable deal. If I didn't have any contract I might look at Fido. My son uses an unlocked Rogers Iphone on Fido and can get voice,sms, and data for $50/mo plus tax - no system access fee.
I am paying $60 plus tax- no system access fee, but I get voice mail and caller ID and some more goodies like 6pm evenings.
I have had a t-mobile G1 since they first came out, only problem is that i`ve been using it on the Rogers network in Canada. The problem with this is that I can not get 3g on my phone, only Edge...which at times is rather painful. I know you can root the Rogers G1 but from what i`m reading there are limitations to the Roms you can put on it. I`m using cyanogenMod (latest) and i use switchrom to try out any new roms that are put out there. Also use A2SD.
What are the limitations, can i still do all that on the rogers G1. If not, is it worth it to sacrifice the 3g to keep these features
There are two ways to root the rogers dream. The first way keeps the original radio but you can only flash roms with a 32A kernel. There are ports for cyanogen and others, check out the sapphire development section. The second way will flash the G1 radio and you can flash any rom you could on the G1. There are some connection problems reported with the second method (mainly a bit slower edge speeds). I originally rooted my phone using this method and it is definitely still usable especially in 3g areas.
I recently bought a Roger's branded Dream off Ebay and rooted via the Haykuro method (which changes the radio). I am a Roger's customer who is coming from a BB Bold 9000 and I can tell you that 3g makes a small difference in cities.
First note is that a stock Roger's Dream has, frustrating at best, 3g connectivity when you are under three bars of service. IMO, EDGE in cities (I am in Toronto) provides what you need. ROMS correct the 3g discrepancy, however 3g is a power hungry beast on the Dream and EDGE has been doing me well.
Second note is that a newer Roger's Dream is a pain in the ass to root compared to our southern neighbours. I lucked out on my Ebay purchase and had a .0009 SPL. Cyanogen offers a method on their Wiki which allows you to keep the Roger's radio but it limits what you can flash as previously stated. The Haykuro method which changes the radio allows you to flash almost any ROM but I have yet to run anything stable.
Just a little food for thought, hope this helped
THIS IS A QUICK QUESTION:
can the rogers dream run all roms posted here? or are there limitations?
if yes, how?
only if you have the danger spl and the newest radio.
but if you are on the Rogers network you may experience connection issues with the new radio...
I would hold off, you don't want to brick your phone. Our rogers Dreams have a different radio EBI1. Most of the roms on here were from the EBI0 radios meaning it will not work. I'm assuming you have a stock phone right now so use this guide. I used this for my rogers Dream and its working great. Add the http for the link.
wiki.cyanogenmod.com/index.php/Full_Update_Guide_-_Rogers_Dream_EBI1_to_CyanogenMod
if you flash the 2.x radio properly along with a proper recovery image, you SHOULDNT brick your phone. i had flashed the 2.x radio and was loading any/every rom you can think of, except i had a whole load of connectivity problems.
so i reverted back to the 3.x radio and have been fine ever since, just using cyans newest with ebi1 kernel.
would love to be able to get a superd rom on here with ebi1 kernel support
HM... ok.
I'm planning to use this on AT&T in the USA... has anyone had experience with this?
is the EBI0 radio acceptable for use with att?
because i'm using my g1 on att right now, and kinda want the 3g speeds. rogers dream does support those frequencies.
jcarrz1 said:
HM... ok.
I'm planning to use this on AT&T in the USA... has anyone had experience with this?
is the EBI0 radio acceptable for use with att?
because i'm using my g1 on att right now, and kinda want the 3g speeds. rogers dream does support those frequencies.
Click to expand...
Click to collapse
The only thing is that you may have slow edge speeds. If you get 3g most of the time that probably doesn't matter.
are slower EDGE speeds with the EBI0 radio confirmed?
See: http://wiki.cyanogenmod.com/index.php/Talk:Full_Update_Guide_-_Rogers_Dream_EBI1_to_CyanogenMod
I don't know exactly why this is or if it happens for everyone.
FWIW, I just tried DSL reports speed test and got 115kbps on AT&T EDGE with the 26I radio on cyanogen. 3G was 992kbps and WIFI 2734kbps.
This compares to 91kbps/625kbps/3659kbps on my stock iphone 3G (3.1.2) tested immediately after the Rogers Dream with 26I on Cyanogen.
At least in terms of speed, I have to conclude that it's a non-issue, at least on AT&T. Time will tell with regards to network stability.
I'm currently downloading the following GPE ROM and I notice it says that you can flash the radio but it is not required. Just wondering what this means exactly? Is it the drivers for the radio device in the headset that gives you your signal? Is it best practice to flash the radio or do most people leave it? What are the pros and cons etc? Is it dangerous to do?
http://forum.xda-developers.com/showthread.php?t=2341395
Thanks
Radios control things like Cellular, WiFi, Bluetooth, GPS.
Each version has its unique radios.
The software that controls them would tell the device to get HSPDA+ on band x or LTE on band Y.. stuff like that.
For example. ME i have T-Mobile. I have a T-Mobile branded HTC One. For a while i ran my One fully stock GPe with the TMO radios. Why? Because when TMO sent out an update a while back (prior to 4.3) they updated their radios and i saw noticeable improvement on LTE for TMO..
SO naturally when i converted mine to GPe i wanted to keep my TMO radios. The GPe might not have the tweaks to its radios that TMO sent out and at the time the version on my GPe was older. So i put the newer TMO radio on it and i felt like it was working great.
Someone else chime in with pros and cons.