Database Develop

[ROM] OFFICIAL T-Mo Vibrant JFD ODIN/Nandroid Backup Images 7/29/10 (Tested/Working)

T959 (US T-Mobile version of the Galaxy S) Firmware that can be flashed through Odin to restore all partitions to the way your phone was shipped to you.
WARNING!!! THIS WILL WIPE ANY DATA ON YOUR DEVICE, IT WILL REPLACE YOUR BASEBAND, KERNEL, RECOVERY AND OS.
JFD ODIN Images from Samsung (PDA)
www.justanotherdev.slackdev.com/T959UVJFD.tar
MD5:632730f6b637f53e5b10e5cbc8b966a7
512 PIT File (PIT Extract first!)
www.justanotherdev.slackdev.com/s1_odin_20100512.rar
MD5:b5628c8e183fdd8f4c703321ca40e33a
ODIN
www.justanotherdev.slackdev.com/Odin3.rar
ALL 3 Files plues the root update.zip
http://tinyurl.com/2bc5b6r
thx to KopyKatKiller
INSTRUCTIONS!
1.Your Device must be in DOWNLOAD mode to use ODIN.
2.Get your phone into Download mode by holding vol down and power.
3.THEN connect your phone to the USB. (some folks have had luck doing it in reverse..connecting the USB then Power and vol down)
4.Open Odin and load each file with it's corresponding field..PIT,PDA,CSC etc. (In this case we just use the PDA and PIT)
5.Don't check anything else, the other two boxes should be checked by default (Auto Reboot and Reset Time)
6.Hit "start"! be patient!
NOTE: COM3 worked fine for me. COM should not matter as long as you are using the correct drivers.
Finally we get some U.S love from samsung firmwares.
For those looking the Nandroid method it is in the post below but only recovers ,system, data, cache and datadata. Not your kernel/recovery or BASEBAND/RADIO (Modem.bin)
Thx to all helping work on the Vibrant. Especially Youneek, Scepterr, MS_Guru, Wes Garner, rhcp0112345, and anyone I may have forgot.
Twitter

NANDROID Images
Extract first!
For BaseBand T959UVJFD
ROOTED
www.justanotherdev.slackdev.com/2010-07-24.18.53.50.zip
MD5:ad0e4709593eb13c8494e62ebd949f17
UNROOTED
http://www.mediafire.com/?kqaulorzx5f6dyq
MD5:baf6e1d532b5dbd76723c64440420302
Thx to youneek.
To Restore
1. Make sure you have clockwork recovery installed (To get Clockwork see this thread)
2. Extract files to /sdcard/clockworkmod/backup/
3. Boot into recovery and select NANDroid and restore
Make sure to check USB debugging to enable ADB access after a restore.
This has been confirmed as WORKING before I uploaded. Any issues please post in this thread. Check MD5 as always after a download.
This will allow those that got stuck on a pre-release or EU ROM to go back to the shipped release TMO ROM for the Vibrant (JFD)
All the thanks goes to Koush for getting fakeflash working on the Vibrant allowing this to happen.

Came from the pre-release?
Flash the software in the first post via ODIN. The Pre-Release is garbage get back to JFD!!

Awesome.....You've just helped alot of people.

And now it begins....Nice to see you back bro!!

For later use...

WilliamStern said:
For later use...
Click to expand...
Click to collapse
why do you need to reserve space? The OP does this so they can post additional info if they need to and its not buried in the thread.

WilliamStern said:
For later use...
Click to expand...
Click to collapse
haha ;]
wanna be one of the first to say 'NANDROIDING!!!'?
i would too haha

You are doing a huge favor to many people, THANKS!

I'll also be adding one from totally stock. No clockworkmod, etc. just bone stock. It'll take about 5 minutes.

Thank you, finnaly! You're the man.
Sent from my SGH-T959 using XDA App

rsfaze said:
why do you need to reserve space? The OP does this so they can post additional info if they need to and its not buried in the thread.
Click to expand...
Click to collapse
How would it get buried? All he has to do is re-edit his OP with updates. It'll stay up top.

WilliamStern said:
How would it get buried? All he has to do is re-edit his OP with updates. It'll stay up top.
Click to expand...
Click to collapse
I think this board only lets you edit your OP after so many days.. but I could have this board mixed up with some of the others I'm on.

rsfaze said:
I think this board only lets you edit your OP after so many days.. but I could have this board mixed up with some of the others I'm on.
Click to expand...
Click to collapse
You could be right... My bad.

Thanks I am currently trying to make an update.zip version for everyone too.
Sent from my SGH-T959 using XDA App

My FTP is giving me fits so I'm uploading it to Multi-Share.

Maybe we should consolidate all of the stock rooted roms to one thread and users can report any problems with any of them.

justanothercrowd said:
My FTP is giving me fits so I'm uploading it to Multi-Share.
Click to expand...
Click to collapse
I am happy that you are back in the game. yours hero ports were the best on G1 back in the day

nick_karstedt said:
Maybe we should consolidate all of the stock rooted roms to one thread and users can report any problems with any of them.
Click to expand...
Click to collapse
we don't really have any yet.. until this nandroid is posted.. the 'stock' roms that have been posted in other threads have all been a beta pre-release from MS_guru.. and in my experience.. its pretty buggy

Great. Lets see if it restores the people who were fooling with the pre-release and had to update to the EU version.
Let us know when its up. and, tested.

how do i entery recovery mode running i9000xxjph rom

can anybody help me i want to root my phone but im using the new beta build of froyo the button combos are not working.
im using samsung captivate

ademejia said:
can anybody help me i want to root my phone but im using the new beta build of froyo the button combos are not working
Click to expand...
Click to collapse
You have to flash a stock captivate kernel, use the key combo, run the update package, then flash back to the JPH kernel again

Zilch25 said:
You have to flash a stock captivate kernel, use the key combo, run the update package, then flash back to the JPH kernel again
Click to expand...
Click to collapse
won't that not work since it's a 2.2 build and we have no available kernels?
did Zilch finally make a mistake? AND I CAUGHT IT!?!?

okay i will try it

I was always under the assumption that with a 2.2 ROM, a 2.1 kernel won't boot (even to recovery, though I assume since it can get to download it can get to recovery now that I think about it) as long as you flash the JPH kernel back immediately after before you boot?
maybe I didn't catch Zilch making a mistake =(

Kaik541 said:
won't that not work since it's a 2.2 build and we have no available kernels?
did Zilch finally make a mistake? AND I CAUGHT IT!?!?
Click to expand...
Click to collapse
Nope, I'm right =P
You have to use it to get the recovery so that you can use our key combos (and power as select), install the package, then flash back. The phone won't BOOT without the JPH kernel but it will get to recovery =P
Ps. NEENER

Zilch25 said:
Nope, I'm right =P
You have to use it to get the recovery so that you can use our key combos (and power as select), install the package, then flash back. The phone won't BOOT without the JPH kernel but it will get to recovery =P
Ps. NEENER
Click to expand...
Click to collapse
one of these days, you'll be drunk or tired and I'll catch you, and then I'll steal your throne!
MWAHAHAAH!
err... *ahem* so yes, booting into recovery to root is possible. just flash back

Kaik541 said:
one of these days, you'll be drunk or tired and I'll catch you, and then I'll steal your throne!
MWAHAHAAH!
err... *ahem* so yes, booting into recovery to root is possible. just flash back
Click to expand...
Click to collapse
I dunno, most likely if I'm drunk I won't be posting on XDA

ummm where can i get a jph kernel. is that the 802 pit file ?

Zilch25 said:
I dunno, most likely if I'm drunk I won't be posting on XDA
Click to expand...
Click to collapse
haha everyone has lonely nights! let me have my dreams

ademejia said:
ummm where can i get a jph kernel. is that the 802 pit file ?
Click to expand...
Click to collapse
the JPH kernel will be inside the flashable package. look for a file named zimage.tar
was meant to imply the kernel was in there, didn't think he wouldn't know what to do with it... zZzzzZzzzzZZZZzz

Kaik541 said:
the JPH kernel will be inside the flashable package. look for a file named zimage.tar
Click to expand...
Click to collapse
No no no, if he does that the zImage file won't be flashable, unless he's on a linux box and can repackage it.
Go to the I9000 forums and find one of the threads about rooting JPH, they have a handy zip that contains the JPH kernel and the update.zip for rooting

Zilch25 said:
No no no, if he does that the zImage file won't be flashable, unless he's on a linux box and can repackage it.
Go to the I9000 forums and find one of the threads about rooting JPH, they have a handy zip that contains the JPH kernel and the update.zip for rooting
Click to expand...
Click to collapse
SHOWS WHAT I KNOW. now you're catching me giving bad advice. today is not my day. I'm gonna go sit and watch Jersey Shore and feel better about myself.

Kaik541 said:
SHOWS WHAT I KNOW. now you're catching me giving bad advice. today is not my day. I'm gonna go sit and watch Jersey Shore and feel better about myself.
Click to expand...
Click to collapse
MUAHAHAHA My how the tables have turned!

when i made my selection of updating the zip then i press power button nothing happens leaves me stuck.
i did the captivate kernel then then i did the recovery to root and applied it. then i flash back the i9000 jhp kernel it wont make my selection to reboot and go in to the os.

ademejia said:
when i made my selection of updating the zip then i press power button nothing happens leaves me stuck.
i did the captivate kernel then then i did the recovery to root and applied it. then i flash back the i9000 jhp kernel it wont make my selection to reboot and go in to the os.
Click to expand...
Click to collapse
I'm curious why it's going back into recovery again- just hook your phone up to your computer and go into your adb folder and type: adb reboot

ademejia said:
ummm where can i get a jph kernel. is that the 802 pit file ?
Click to expand...
Click to collapse
stock kernel is the 2.6.29 [email protected] #2 right?

androidftwin said:
stock kernel is the 2.6.29 [email protected] #2 right?
Click to expand...
Click to collapse
Yup, thats stock captivate

I curious as to why people lately have been trying the i9000 jph? Yes, I would want 2.2 also but that thing is not made for these phones and with all the people lately having trouble, why bother? Just flash back to stock, use adb if buttons don't work, and load Eugene's captivate hybrid. It's fast, doesn't have the att/samsung bloat, and it works without bricking our phones.

bobbylx said:
I curious as to why people lately have been trying the i9000 jph? Yes, I would 2.2 also but that that thing is not made for these phones and with all the people lately having trouble, why bother? Just flash back to stock, use adb if buttons don't work, and load Eugene's captivate hybrid. It's fast, doesn't have the att/samsung bloat, and it works without bricking our phones.
Click to expand...
Click to collapse
Eh JPH works fine on the Captivate (even external SD shockingly enough)- it's just not that great of an upgrade period though =P

How to unroot my verizon tab

Alright guys i have searched and tried and tried. Currently i am on dj11 with kernal version stated as 2.6.32.9 and right below it has [email protected]#3. I am on 2.2
So what ive tried:
-I used heimdall to flash back to stock but as you can see the kernal version says im still rooted although superuser app is not installed. This causes the update to fail
-I tried to use superoneclick method to unroot but it does not work
What i want is to be stock with no root and be able to update. Any help or suggestions would be appreciated.
FYI i also used all the thread procedures on the forum (gizmo ninja and how to unbrick tab)

Try using this stock unrooted rom. Link below:
http://forum.xda-developers.com/showthread.php?t=1136587

TabFreak said:
Try using this stock unrooted rom. Link below:
http://forum.xda-developers.com/showthread.php?t=1136587
Click to expand...
Click to collapse
i believe i tried that already and it still had the words "rooted" under the kernal version. It also didnt allow me to update. I will try it again.

Try this instead.
http://forum.xda-developers.com/showthread.php?t=1033586
The second link takes you to the files.

TabFreak said:
Try this instead.
http://forum.xda-developers.com/showthread.php?t=1033586
The second link takes you to the files.
Click to expand...
Click to collapse
Will try now. Ahh I hope this works!

killerapl said:
Will try now. Ahh I hope this works!
Click to expand...
Click to collapse
Flashed and guess what?? Didnt work. Kernal version still says 2.6.32.9 [email protected] Ugh!!!

Don't know what the problem could be. That has always worked for me. If you go to the "System-- About Device-- System Updates" does it give you the option to update? When I have restocked mine and set up a wireless connection it always tries to download and install the update.

TabFreak said:
Don't know what the problem could be. That has always worked for me. If you go to the "System-- About Device-- System Updates" does it give you the option to update? When I have restocked mine and set up a wireless connection it always tries to download and install the update.
Click to expand...
Click to collapse
Yeah it does. Goes halfway and then stops and has exclamation mark. I tried gizmoninjas method to update but still quits. I'm totally lost.
Sent from my SCH-I510 using XDA App

I don't know what to do. If it were me I would go ahead and grab the EC02 update from here: http://www.blackmugmedia.com/Android/GT/Mirror/Roms/CDMA/Recovery to Stock /
Flash that. You will have the latest official release, or you could get the VZW Leaked Gingerbread release from the Developers section. (That is what I am running on my VZW tab).
Maybe if you flashed the EC02 update and then used the going back to stock instructions it would unroot you. I have always unrooted using that rom and directions when I wanted to start fresh from a custom rom that didn't quite work like I wanted it to work.

TabFreak said:
I don't know what to do. If it were me I would go ahead and grab the EC02 update from here: http://www.blackmugmedia.com/Android/GT/Mirror/Roms/CDMA/Recovery to Stock /
Flash that. You will have the latest official release, or you could get the VZW Leaked Gingerbread release from the Developers section. (That is what I am running on my VZW tab).
Maybe if you flashed the EC02 update and then used the going back to stock instructions it would unroot you. I have always unrooted using that rom and directions when I wanted to start fresh from a custom rom that didn't quite work like I wanted it to work.
Click to expand...
Click to collapse
I will give that a shot. The current gb leak is rooted. I did post asking to see if they (oldmacnut) had the unrooted version. Personally I like the rooted option but I do want to sell the tab and can't sell it rooted unless the person doesn't care. Bedside this issue the tab is fine and working properly.
Thank you so much for all your help. I will keeep you posted on the outcome.

Nope didn't work. Still rooted. I'm so over this hahah
Sent from my SCH-I510 using XDA App

I am at a loss. I know there are ways to get this done, but I have no idea where you can go from here. Not an expert, sorry!

TabFreak said:
I am at a loss. I know there are ways to get this done, but I have no idea where you can go from here. Not an expert, sorry!
Click to expand...
Click to collapse
There has to be. Wish it was like my Droid charge and just flash via Odin. If I can get the ginerbreak leak with no root I will be happy.
Or sell it to someone that doesn't mind its rooted.
Sent from my SCH-I510 using XDA App

There is a unrooted version of Gingerbread that you can flash with Odin:
http://www.mydroidworld.com/forums/...w-sprint-2-3-4-ef01-rooted-updated8-15-a.html
I haven't used Odin, but if you are familiar with it you might have luck with this. I think you use 7zip to extract and then use the resulting md5 file in the One Package location. You might want to look there and get that file.

TabFreak said:
There is a unrooted version of Gingerbread that you can flash with Odin:
http://www.mydroidworld.com/forums/...w-sprint-2-3-4-ef01-rooted-updated8-15-a.html
I haven't used Odin, but if you are familiar with it you might have luck with this. I think you use 7zip to extract and then use the resulting md5 file in the One Package location. You might want to look there and get that file.[/QU
I'm gonna give it a try tomorrow. I just have to make sure if I flash under phone or PDA with Odin. Don't know if you know. For phones its PDA. Not sure with tabs. Thank you so much
Sent from my SCH-I510 using XDA App
Click to expand...
Click to collapse

I just tried this.
Unzip the .md5 file with 7zip, you will get an error about no proper ending or something. Take your zimage, cache, param, dbdata, factoryfs, recovery.bin and place them in the proper locations in Heimdall. Flash your tab and let it boot up.
You should have a fully functional gingerbread without root.
I just did it on my tab.

TabFreak said:
I just tried this.
Unzip the .md5 file with 7zip, you will get an error about no proper ending or something. Take your zimage, cache, param, dbdata, factoryfs, recovery.bin and place them in the proper locations in Heimdall. Flash your tab and let it boot up.
You should have a fully functional gingerbread without root.
I just did it on my tab.
Click to expand...
Click to collapse
You effin rock!!! It worked! I now have non rooted stock gingerbread. Thank you for all your help and investigation for the right files. Youre awesome. Now time to sell this baby
Or i spent so much time doing this i think im attached now hahaha

Glad it worked the way you wanted. I went back to the rooted version of Gingerbread. Everything works the way I want it to so no reason to change (for now anyway).

New Canadian (900W8) ROM's released

Went to SamMobile today. Finally got an update from Samsung for my Rogers device, the SM-G900W8. It's dated July 2014, previous for Rogers was April.
Here are the PDA and CSC versions: G900W8VLU1ANF3 G900W8OYA1ANF3
Link is here: http://www.sammobile.com/firmwares/
Anyone install it yet? Anyone notice any difference?

Got the new ROM update this morning thru OTA. I don't see anything new or special. Still at 4.4.2

Anybody able to extract the NF3 modem from it and make it into a flashable file? That'd be gravy...

Tried to find a change log to see if there were any important changes, but no luck.

harry_fine said:
Went to SamMobile today. Finally got an update from Samsung for my Rogers device, the SM-G900W8. It's dated July 2014, previous for Rogers was April.
Here are the PDA and CSC versions: G900W8VLU1ANF3 G900W8OYA1ANF3
Link is here: http://www.sammobile.com/firmwares/
Anyone install it yet? Anyone notice any difference?
Click to expand...
Click to collapse
Thanks :good: I hope it fixes the problem I have with the radio getting stuck on 3G after calls...

I extracted the modem.... tried to make a flashable CWM file for you guys but 7zip is giving me a hard time... then again, I think it's better if you just flash from Odin directly, I believe it's safer

What about a Rom?. I wish I was able to I would have us a Canadian rom.

Well, this is NOT a flashable modem, merely the modem all rar'ed up; just download it, extract it, and flash it via PHONE on Odin 3.09, and you should be golden. If it does not stick, remove the battery for 15 seconds, and get into Download mode via the usual button combinations, then flash away.
G900W8_NF3_MODEM
---------- Post added at 03:34 AM ---------- Previous post was at 03:32 AM ----------
ChantalCaron13 said:
What about a Rom?. I wish I was able to I would have us a Canadian rom.
Click to expand...
Click to collapse
Lol why... just flash an international rom, works just as good... and if you really want to be up to date, just flash the modem I just posted.
Yes, you just
1- Download any international rom your body pleases
2- Flash it
3- Go eat a sandwich
Simple pimple control

omegajester said:
Well, this is NOT a flashable modem, merely the modem all rar'ed up; just download it, extract it, and flash it via PHONE on Odin 3.09, and you should be golden. If it does not stick, remove the battery for 15 seconds, and get into Download mode via the usual button combinations, then flash away.
G900W8_NF3_MODEM
---------- Post added at 03:34 AM ---------- Previous post was at 03:32 AM ----------
Lol why... just flash an international rom, works just as good... and if you really want to be up to date, just flash the modem I just posted.
Yes, you just
1- Download any international rom your body pleases
2- Flash it
3- Go eat a sandwich
Simple pimple control
Click to expand...
Click to collapse
Just hate that the phone dialer app on the int roms have the videocall icon on the bottom left corner instead of the text icon.

ChantalCaron13 said:
Just hate that the phone dialer app on the int roms have the videocall icon on the bottom left corner instead of the text icon.
Click to expand...
Click to collapse
Flash a T Mobile rom then... works just as good, plus you get the white dialer background, etc.

Flashed new modem, success. Via odin 3.09

Brava27 said:
Flashed new modem, success. Via odin 3.09
Click to expand...
Click to collapse
How's it going with it so far? At least my phone gets stronger reception in places it was weak before.

omegajester said:
How's it going with it so far? At least my phone gets stronger reception in places it was weak before.
Click to expand...
Click to collapse
How do you flash the new radio Bin file from Odin? I've done .tar files before for ROM's and such.

Anything new with this build ?

harry_fine said:
How do you flash the new radio Bin file from Odin? I've done .tar files before for ROM's and such.
Click to expand...
Click to collapse
Extract the zip file I uploaded; you're going to be left with a modem.bin. Flash via Odin as usual, just don't do it via PDA; use PHONE option instead.

So far I've noticed that you have to agree to terms for ultra power saving mode now when you first turn it on, and normal power saving mode shows an icon at the top left now when on.
Sent from my SM-G900W8 using XDA Premium 4 mobile app

omegajester said:
How's it going with it so far? At least my phone gets stronger reception in places it was weak before.
Click to expand...
Click to collapse
harry_fine said:
How do you flash the new radio Bin file from Odin? I've done .tar files before for ROM's and such.
Click to expand...
Click to collapse
No differences really, new modem flashed bin through Odin 3.09 and good reception. Clicked phone or CP and boom. Profit
Sent from my SM-G900W8 using Tapatalk

Thanks for the radio.

Am I the only one for whom the update failed? Because I tried twice to install it and I receive a message telling me that the updated failed to install correctly twice.

Worked fine for me. Towelroot still works too.
Sent from my SM-G900W8

[ROM][TAR] Stock NG2 Odin flashable

You will get the KNOX bootloader if you flash this.
YOU CANNOT UNDO THIS, ITS PERMANENT. FLASHING ANYTHING UNOFFICIAL AFTER FLASHING THIS TAR WILL VOID YOUR WARRANTY​
Just the NG2 FULL stock tar.
Do NOT rename the tar file. Even though it may be convenient to do so, Odin may fail the md5 check for no reason.
(L720VPUFNG2_L720SPTFNG2_L720VPUFNG2_HOME.tar.md5)
This is NOT ROOTED. Its the original TAR file for people who need an Emergency Recovery for their phones, and dont want to wait hours for it to download from slow file hosts.
Mediafire
Instructions:
1. Download and Extract tar above and download Odin
2. Put phone into download mode (power off, then power button + Volume Down, then volume up when prompted)
3. Open Odin (right click > open as administrator)
4. Load stock tar into the PDA slot
5. Start flashing
6. Grab some popcorn because it will take a while
7. Profit

Is this going to update bootloader into NG2?
Is NG2 bootloader unlocked?
Thank you so much,

will this work on rooted phone?
im looking to put my phone back to unrooted stock. will this flash right on a rooted phone? im guessing it will but just want to make sure.

jam97 said:
Is this going to update bootloader into NG2?
Is NG2 bootloader unlocked?
Thank you so much,
Click to expand...
Click to collapse
Yes this will update you to the new update NG2 and no the bootloader is still locked.
chriseboy said:
im looking to put my phone back to unrooted stock. will this flash right on a rooted phone? im guessing it will but just want to make sure.
Click to expand...
Click to collapse
Yes this will flash right on a rooted phone. The purpose of this is to go back to stock from either rooted or custom rom.
Sent from my SPH-L720

ROMANTiC KiD said:
Yes this will update you to the new update NG2 and no the bootloader is still locked.
Yes this will flash right on a rooted phone. The purpose of this is to go back to stock from either rooted or custom rom.
Sent from my SPH-L720
Click to expand...
Click to collapse
sorry for this stupid question , but will I be able to flash a custom recovery after flashing this image?
Thank you,
Sent from my SPH-L720 using XDA Free mobile app

jam97 said:
sorry for this stupid quastion , but will I be able to flash a custom recovery after flashing this image?
Thank you,
Sent from my SPH-L720 using XDA Free mobile app
Click to expand...
Click to collapse
You will need to re-root the phone after installing this file! Then you will be able to install a custom recovery..

Thanks for putting this on a speedy host. I just downloaded it tonight in under half an hour at my daughter's house, and she doesn't have a particularly fast internet connection.
A quick question - does this file leave your programs intact? Sometimes I like a total wipe (except for my SD card), and start fresh.
Thanks again

my wifi is broken after flashing. won't turn on

rtwrobert10 said:
my wifi is broken after flashing. won't turn on
Click to expand...
Click to collapse
same problem let me know if you find how to fix it

rtwrobert10 said:
my wifi is broken after flashing. won't turn on
Click to expand...
Click to collapse
biscojams said:
same problem let me know if you find how to fix it
Click to expand...
Click to collapse
Reflash it again
Sent from my SPH-L720

rtwrobert10 said:
my wifi is broken after flashing. won't turn on
Click to expand...
Click to collapse
biscojams said:
same problem let me know if you find how to fix it
Click to expand...
Click to collapse
ROMANTiC KiD said:
Reflash it again
Sent from my SPH-L720
Click to expand...
Click to collapse
Same here, I wiped then installed twice, no wifi. I'll try one more time,

DAFTEK said:
Same here, I wiped then installed twice, no wifi. I'll try one more time,
Click to expand...
Click to collapse
Try flashing the ng2 kernel after the install. Thru custom recovery.
https://www.androidfilehost.com/?fid=23622183712458388
Thanks to @ g_ding84

DAFTEK said:
Same here, I wiped then installed twice, no wifi. I'll try one more time,
Click to expand...
Click to collapse
That's odd.
I have installed this NG2 tar file with Odin on 2 different phones and WiFi works perfect on both..

2WhiteWolves said:
Try flashing the ng2 kernel after the install. Thru custom recovery.
https://www.androidfilehost.com/?fid=23622183712458388
Thanks to @ g_ding84
Click to expand...
Click to collapse
Thanks for the reply. I did try one more time and this time I went back in recovery and did the two wipes, went back in to download, opened odin3 3.09 via administrator and removed the auto reboot check. after it finished i manually rebooted and wifi worked.
---------- Post added at 10:06 PM ---------- Previous post was at 10:02 PM ----------
Now I have another problem. I am no longer with sprint and my phone is unlocked from sprint. I have been using the GOLDENEYE rom on Walmart Family Mobile and all was warning well except for sometimes not connecting calls so I thought i go back to stock with this rom. Problem now is I can make calls with the Walmart sim card, put in the APN settings but i am unable to remove the Hands Free Activation nagging.. Is there anyway to make it go away?

DAFTEK said:
[/COLOR]Now I have another problem. I am no longer with sprint and my phone is unlocked from sprint. I have been using the GOLDENEYE rom on Walmart Family Mobile and all was warning well except for sometimes not connecting calls so I thought i go back to stock with this rom. Problem now is I can make calls with the Walmart sim card, put in the APN settings but i am unable to remove the Hands Free Activation nagging.. Is there anyway to make it go away?
Click to expand...
Click to collapse
Have you tried to pull down the notification bar with two fingers > long press on Hands Free icon to see if something is turned on to make it show up on notification bar? If turned on, shut it off. Hopefully it is that simple. If not that simple, I have no clue how to make it stop. Maybe someone else does.
I haven't heard of anyone having that problem.

Yeah, I tried everything, it's part of the rom I think, nothing worked to make it go away..
I just went back to goldeneye rom, all working perfect again. Thanks.

I just flashed this rom through odin and it didn't wipe any of my programs, isn't is supposed to?

RTbar said:
I just flashed this rom through odin and it didn't wipe any of my programs, isn't is supposed to?
Click to expand...
Click to collapse
+1
also I confirm that everything is working great.

RTbar said:
I just flashed this rom through odin and it didn't wipe any of my programs, isn't is supposed to?
Click to expand...
Click to collapse
Nope. it doesn't wipe data unless stated by the OP that it does. It only restores any apps deleted, or reverses any mods made. Example if you are running Aosp and Odin back to stock. You will get bootloop. After Odin always go to stock recovery and do a factory reset to have a clean install.
Sent from my SPH-L720

Wifi didn't work for me on this rom, coming from a custom mf9 rom. So I odin mf9 bootloader package, and then flashed stock mf9 odexed rooted rom, then odin the mf9 kernel. And did NG2 upgrade through Kies. Now Wi-Fi finally works for me but it's impossible to root. But at least now I got everything working, when I get off of work I can flash the OP version of NG2 cuz at least I could root that 1.