Database Develop

Galaxy S Dead (not like the other ones)

Hi all guy's,
i have a realy strange problem , i tried to find a solution on this forum and on the net but i didn't find nothing
Today i was trying to change firmware by Odin (it was not my first time) , i used not my home pc ( like i did many time) but another one, opned odin, load the firmware , plugged in the galaxy in download mode and i clicked on start (obiviusly odin showed my galaxy s) but program stuck and on galaxy screen there wasn't the progress bar as usually. After five minutes i unplugged the phone and i rebooted it, on screen there was the computer and the phone with the yellow esclmation point.
i unplugged the battery and than i putted the galaxy s in download mode (vol down+ power+ home button), than i rebooted the pc, i deleted all the tons samsung modem drvier installed on windows xp (i think this was the problem of the bad flash on odin) , opend again odin, plugged the phone on the pc but nothing happned, the pc didn't recognized the phone (not like the others) , i connected the phone to usb to the computer and nothing happned how if i wouldn't connect nothing on pc. Obiviusly Odin didn't recognized the phone and kies also. I went on another pc , i installed kies , than odin, and i connected my phone and i had the same truble, when i conect my phone to the computers is like if i don't connect nothing, becouse nothing happen on computer. My galaxy go in download mode but the computer's don't recognize it!

did you try another usb cable? maybe your cable is damage... just covering solutions...

I don't think your galaxy is dead, as long as you can access the download mode you should be ok.
Try with different usb ports/cables/computers.
But it sounds most likely that your drivers aren't installed properly. You shouldn't have uninstalled them in the first place if they were working lol (it's unlikely the driver caused bad flash, it either works or it doesnt!)

plug it in the computer without the battery or simcard or memorycard, do it in windows and not in Odin. Then try to connect to Odin.

Scag said:
Hi all guy's,
i have a realy strange problem , i tried to find a solution on this forum and on the net but i didn't find nothing
Today i was trying to change firmware by Odin (it was not my first time) , i used not my home pc ( like i did many time) but another one, opned odin, load the firmware , plugged in the galaxy in download mode and i clicked on start (obiviusly odin showed my galaxy s) but program stuck and on galaxy screen there wasn't the progress bar as usually. After five minutes i unplugged the phone and i rebooted it, on screen there was the computer and the phone with the yellow esclmation point.
i unplugged the battery and than i putted the galaxy s in download mode (vol down+ power+ home button), than i rebooted the pc, i deleted all the tons samsung modem drvier installed on windows xp (i think this was the problem of the bad flash on odin) , opend again odin, plugged the phone on the pc but nothing happned, the pc didn't recognized the phone (not like the others) , i connected the phone to usb to the computer and nothing happned how if i wouldn't connect nothing on pc. Obiviusly Odin didn't recognized the phone and kies also. I went on another pc , i installed kies , than odin, and i connected my phone and i had the same truble, when i conect my phone to the computers is like if i don't connect nothing, becouse nothing happen on computer. My galaxy go in download mode but the computer's don't recognize it!
Click to expand...
Click to collapse
I think you saw this wonderful picture
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Welcome to SGS Bricked Club (unofficial)
Your phone is not dead, just bricked.
Do this
1. Re-install all your Kies to get SGS USB driver (you shouldn't have uninstall it in the first place)
2. Switch your phone to download mode
3. On Odin, select 512 pit (ONLY), and checked "Re-partition" option
4. Connect your phone and USB (remember, download mode first > Odin > USB Connect)
5. Click Start on Odin
6. Wait until Odin turn green with "SUCCESS"
7. Click Reset on Odin
8. flash what ever firmware you want, accordingly

Without trying to be too optimistic, as well as not being too much of a downer, I've had that particular "phone ! computer" screen a few times and not had any problems flashing with Odin later. Usually takes a couple of PC and phone reboots but like someone said, as long as you can get to the recovery (android at work) screen one way or another, you *should* be fine.

I've got that problem also many times and have seen the "phone-to-pc" screen, too. Take a look into your Device Manager under modem before you plug in the phone. After you plugged in the phone is there a modem displayed? My Problem is that Windows change the Driver through CDMA Modem for Samsung and with that Driver odin doesn't work. I've managed that problem by changing the machine or the port for a new driver select.

frak!!! krap! i think my phone is krapped out.
although i can get to download mode, i can not get to recovery mode
when you flash official firmware, are you supposed to flash with re-partition checked, the pit and the pda file all at once?
cuz i get stuck on...
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
the phone's screen turns off... and remains 'off'
if only pit and pda file are used, it gets stuck on...
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> cache.rfs
<ID:0/004> dbdata.rfs
with the screen turns all green... and freezes

great.... sometimes from recovery it would goes blue or pink screen and freeze.
anyone got any tips or ideas?
dumb... after 6 hours of fiddling... the one thing i didn't do was try on a different usb input.
however, i still can not explain the green, blue, or pink freeze screens
ps. thanks roy, your help and concern helped me profoundly (seriously)

PatcheZ said:
frak!!! krap! i think my phone is krapped out.
although i can get to download mode, i can not get to recovery mode
when you flash official firmware, are you supposed to flash with re-partition checked, the pit and the pda file all at once?
cuz i get stuck on...
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
the phone's screen turns off... and remains 'off'
if only pit and pda file are used, it gets stuck on...
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> cache.rfs
<ID:0/004> dbdata.rfs
with the screen turns all green... and freezes
Click to expand...
Click to collapse
sorry to hear this mate, I personally never experience this.
Mind share your Odin setup for flashing?

ok guy's some of you didn't focus my problem (maybe becouse of my crap english) anyway the problem wasn't how to go in download mode but the problem was another one, once i was in download mode the computer didn't recognize the phone, it was like if i wouldn't put nothing in the usb, and well it wasn't a usb clabel, usb port, driver or some other things but it was soemthing fuked up with my phone.
The following procedure is not needed if you have some problem with driver but only if your computer defintly don't show nothing when u plug the phone in download mode after a bad flash.
Turn off the phone and unplug the battery, connect the phone to the computer, wait a minute than click the 3 keys for put the phone in download mode (vol down+home+power) and plug in the battery. Your computer should recognize soemthing and u will be able with the correct driver and Odin program to flash the phone again. Your phone should be usb connected all the time or the procedure don't work.
I have another bug now and i don't know if it's related to the firmware(i tried on jm6 and jm7) or there is something wrong with my phone usb.
When i turn on my phone randomly don't work the sound selection on the menu and when i tap the number on the phone keyboard. If i plug in the phone on the pc i'm not able to use kies or other things like mass storage but on the phone start the music player (like if i would plug in the headphone) and the bug get fix.
When the bug come if i not plug in the phone on the computer the ringtone work if i get a call but n the phone there is the handsfree option activate.
I don't know what to do and i hope u understand my problem even if my english sux hard
Thanks for your attenction
EDIT: guy's the bug is not related to the firmware (i didn't have it first of yesterday), i tried now the jg5 and i still to have the same problem as on the jm6 and jm7 , sometimes randomly the button sounds don't work when i'm in the menu or when i'm making a telephon number even if the option is enable in the menu. for fix it how i write up herei need plug in the phone cable on the computer or turn off and than turn in again till it get fix.

hI,
i BRING UP A NEW PROBLEM THAT I AM MY SELF INTO.
As many of you i used odin to flash my room but this time i used an odin called "I897UCJI6-OCD-REV02-Low",everithing looks fine after flashing but is not,in phone info shows that my model is samsung SGH-i897,and every time i try to charge or connect via usb the phone turns off,doesn't go in download or recovery mode, basically is dead couse i cannot change nothing and the phone buttons does not have the same function.
How can i go back to galaxy s?
PLEASE,HELPPPP!
DETAILES OF ROOM ARE:
PDA: I897UCJI6
PHONE: I897UCJI6
CSC: I897ATTJF6
FIRMWARE VERSION 2.2
KERNEL VERSION : 2.6.32.9 - [email protected] 11 #1
FROYO.UCJI6

You haven't got a captivate then?
the proper ROM wouldn't be on this forum but the captivate's one, but when guessing you're actually in possession of a i9000m; why not a i9000 rom from the i9000 section?
cos a i897 is a galaxy captivate, doesn't seems wrong when you have one? =/

zenopetrea said:
hI,
i BRING UP A NEW PROBLEM THAT I AM MY SELF INTO.
As many of you i used odin to flash my room but this time i used an odin called "I897UCJI6-OCD-REV02-Low",everithing looks fine after flashing but is not,in phone info shows that my model is samsung SGH-i897,and every time i try to charge or connect via usb the phone turns off,doesn't go in download or recovery mode, basically is dead couse i cannot change nothing and the phone buttons does not have the same function.
How can i go back to galaxy s?
PLEASE,HELPPPP!
DETAILES OF ROOM ARE:
PDA: I897UCJI6
PHONE: I897UCJI6
CSC: I897ATTJF6
FIRMWARE VERSION 2.2
KERNEL VERSION : 2.6.32.9 - [email protected] 11 #1
FROYO.UCJI6
Click to expand...
Click to collapse
And once again epic fail.
Your phone is bricked now, go and exchange it.

I think that last hope is try to forcing download mode with "resistor on usb port" method:
http://forum.xda-developers.com/showthread.php?t=819551

Thanks guys,
What is bad is,that every time i try to connect with usb or charger the phone turns off and nothing shows on the screen,once i remove the cable the phone turns on normaly.Maybe i can still go in download mode by changing the configuration of the buttons,couse cativante has 4 buttons and galaxy 3,the think is that home button has no function and back touch button become home thats way i cannot go into download mode no home button.If nothing will work i gues i have to follow Jonsat's advice.I still have hope that someone nows and shares with as.
Thanks !!!!!!!!!!!

zenopetrea said:
hI,
i BRING UP A NEW PROBLEM THAT I AM MY SELF INTO.
As many of you i used odin to flash my room but this time i used an odin called "I897UCJI6-OCD-REV02-Low",everithing looks fine after flashing but is not,in phone info shows that my model is samsung SGH-i897,and every time i try to charge or connect via usb the phone turns off,doesn't go in download or recovery mode, basically is dead couse i cannot change nothing and the phone buttons does not have the same function.
How can i go back to galaxy s?
PLEASE,HELPPPP!
DETAILES OF ROOM ARE:
PDA: I897UCJI6
PHONE: I897UCJI6
CSC: I897ATTJF6
FIRMWARE VERSION 2.2
KERNEL VERSION : 2.6.32.9 - [email protected] 11 #1
FROYO.UCJI6
Click to expand...
Click to collapse
Man, i have an idea:
1) Download z4root from market, root ur phone;
2) Download Rom Manager and flash recovery;
3) Download a Rom in which u have the extend power menu;
4) Flash Rom;
5) Boot into Rom and enter in the extend power menu;
6) From the extended power menu press "Reboot into download mode";
7) Flash from Odin.
PS: if your power menu button doesn't go well u should download from the market apps that emulate the power button menu!
I know it's a crazy idea but in my opinion you should try!

Scag said:
ok guy's some of you didn't focus my problem (maybe becouse of my crap english) anyway the problem wasn't how to go in download mode but the problem was another one, once i was in download mode the computer didn't recognize the phone, it was like if i wouldn't put nothing in the usb, and well it wasn't a usb clabel, usb port, driver or some other things but it was soemthing fuked up with my phone.
The following procedure is not needed if you have some problem with driver but only if your computer defintly don't show nothing when u plug the phone in download mode after a bad flash.
Turn off the phone and unplug the battery, connect the phone to the computer, wait a minute than click the 3 keys for put the phone in download mode (vol down+home+power) and plug in the battery. Your computer should recognize soemthing and u will be able with the correct driver and Odin program to flash the phone again. Your phone should be usb connected all the time or the procedure don't work.
Click to expand...
Click to collapse
I have exactly the same problem, the pc recognize the phone just as unkown device.
Witch driver do I need to get Odin to work?
Thanks in advance

I need some help here. My phone went dead during charging yesterday..... it was fine one moment and last check was at 80%. Then about 10 min later when I wanted to unplu & use... it was not responding at all. Noticed that the phone was rather warm as well.
I've been running "Insane" kernel for a week with overclock to 1200 and under volt about -75 across the board. Did I fry the chip???
Phone is not respondingf at all. Doesn't charge, cannot boot, cannot do into download or recovery mode, PC does not even see it when plugged in, pulled battery & re-insert does not help.
What other options do I have??? Last resort is to bring back to the service centre, but I'm afraid that they will not give warranty for it if checked that I have an "Insane" kernel.
Advise & feedback please. Any other areas to check?

Odin flash not proceeding, Android not booting

Well, I guess I messed my SGS up.
A short overview of what happened:
I tried to replace framework-res.apk on the official Froyo (rooted using OneClickRoot method) with one I modified. After deleting the original file I was unable to move the new one into its place as, despite me deleting a few ringtones, it kept stating that not enough space was available. So I decided to go into recovery mode, hoping I'd be able to fix this (I had a backup of the file on /sdcard/) I wanted via adb's shell from there. Well, su doesn't work in recovery mode ("Permission denied") and neither does adb remount ("remount failed: No such file or directory").
This is where the real trouble starts:
When I launch Odin3 (1.30), the phone seems to be recognised - if a yellow field with a COM port listed and "<ID:0/009> Added!!" in the message area is any indication. After selecting my PIT and PDA file and clicking Start, this is what Odin tells me:
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
Aaaand that's it. I have tried both with the 512 and 803 PIT and even tried flashing JPK onto it to no avail, it just stays stuck at SetupConnection.
I also wiped everything on the phone as well just to make sure nothing is interfering. Thanks to me messing with the framework-res.apk, adb can't be used while the phone is "running" Android (with a black screen and I suppose constant FC everywhere because of the vibrations).
I'm pretty much out of ideas right now after having tried for hours to revive my baby, but maybe one of you magicians out there can help me find something I haven't thought of yet?

Remove the battery and put i back.
Go to download mode.
Try again.
Sometimes you need to reinstall the drivers.
If you have more usb stuff locked up. Remove them. Odin is a little baby
Sent from my GT-I9000 using XDA App

DamianGto said:
Remove the battery and put i back.
Go to download mode.
Try again.
Sometimes you need to reinstall the drivers.
If you have more usb stuff locked up. Remove them. Odin is a little baby
Click to expand...
Click to collapse
Oh dear, thank you so much for having me read this again. Download mode != recovery mode, and volume up != volume down.
Flashing now, I'll update this if it turns out to be fixed. Derp.
/edit: Well, fixed it now. Thanks again

Liquidator said:
Oh dear, thank you so much for having me read this again. Download mode != recovery mode, and volume up != volume down.
Flashing now, I'll update this if it turns out to be fixed. Derp.
Click to expand...
Click to collapse
Hope it worked for you this time.
Sent from my GT-I9000 using XDA App

[Q] Galaxy Note Stuck at Boot Screen

Hi I just decided to change my custom firmware to darkynote from rocketrom. It worked perfectly but I wanted to update my kernal also so afterwards i rebooted into recovery and installed version 2.6 of Abyss Note. Now My phone boots to the "Samsung Galaxy Note N7000" Screen and stays there unless i plug it in, then when i start it it goes to a frozen battery screen. I cant boot into recovery but i can boot into download mode. Can someone help me get my phone back to stock? I can't seem to find a tutorial anywhere that will work for me.
please help
edit: extra details, the Odin3 v1.85 process gets stopped at NAND Write Start!!
Here is the message feed:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKL7_N7000OXAKL7_N7000XXKL7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> factoryfs.img
<ID:0/006> NAND Write Start!!

Also tried using CF-Root kernal. no luck there. The Bar in Odin says KERNEL and the green bar is full, also stuck at NAND Write Start!!.
Someone respond, im gonna cry.

First Relax man, dont be in hurry, read this guide twice/thrice n calmly proceed...
It is nice still you can entre to download mode.
First get Stock firmware from here Type N700 in search field, it will show all available firmware, select you wish to flash n download
Note : If you select latest ROM KL7, you won't get Root + CWM, for that you have to Flash another ROM first, then You have to Root + CWM,then Install Mobile odin pro, now flash KL7 with Mobile Odin pro with 'ever root' option enable. If you selecting another ROM, ignore this note
Get odin n extract
Install:
Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly.
Extract tar file from the ROM you have download(password available at site from you have download). Put the phone into download mode (vol. down+home+power buttons),
Comlete close kies, if open. start odin, connect the phone via USB. Choose continue on the phone,
make sure that only two boxes are checked in odin - Auto Reboot and F.Reset Time.
Choose PDA button in Odin and select tar file you extracted before.
Choose START button.
The phone will reboot after the flash. Done.

Alright sounds good but i left it at the NAND write start thing overnight and when i came back it said this:
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Now I have a black screen and its flashing on and off with the frozen battery symbol. I think the battery is drained or something.
Also my download of the rom finished, there isnt any tar files its just a zip with an MD5 file and a Dll. Should i just but the MD5 file in the PDA section?
Edit: now my phone wont do anything when i try to put it in download mode.

Anyway if you are still able to entre Download mode, then try to flash stock kernel as i said above.

But thats what I mean, is it possible for the phone to not boot into download because the battery is dead or is my phone just bricked forever $850 dollars out the window.

tangelos said:
I cant boot into recovery but i can boot into download mode.
Click to expand...
Click to collapse
Actually i dont understand properly, your first post said U R getting into DW mode, if you can entre into boot mode, i guide you earlier, i cant say it bricked.
many time this happen after some error in procedure.
If you even not able to entre into Download mode, you need to entre it with JIG.

dr.ketan said:
Actually i dont understand properly, your first post said U R getting into DW mode, if you can entre into boot mode, i guide you earlier, i cant say it bricked.
many time this happen after some error in procedure.
If you even not able to entre into Download mode, you need to entre it with JIG.
Click to expand...
Click to collapse
Actually I was just updating you. At first it was working, then i tried a tutorial simmilar then the one you just gave me and it caused the phone to not turn on whatsoever. Can you link me to one of these "jigs". Thanks

You can get it readymade from market e.g. ebay or you can make it own home made
see here http://forum.xda-developers.com/showthread.php?t=819551
better first try with other battery once, if you cud manage

I was able to get a hold of one locally. When I plug it in, nothing happens. Any advice? Its for a GSII. Is that why? Or is it the battery thing. Before it stopped working completely, when i booted into download it would say low battery. Looks like its game over for my new phone .

I tried this with an old usb cable http://forum.xda-developers.com/showthread.php?p=20914895#post20914895.
Inserted the USB Jig afterwards. No luck
I suppose i have to take it to be J-tagged: http://toronto.kijiji.ca/c-buy-and-...-JTag-Service-Phone-Unlock-W0QQAdIdZ341742939

I'm sorry if this is not helping, or being so late, but I wanted to share my experience.
So, now can you enter the recovery menu by pressing the 3 buttons?
if you can then do a factory reset/wipe from the recovery and then flash an entire flashable ROM, maybe a stockROM or ROCKETROM.
you can upload ROCKETrom from the ordinary windows explorer , just copy and paste to the ex.SD.
the looping android animation actually happened to mine, and that's how I fixed it.
BTW: I didn't use Odin at all, or any other program.

Thanks for trying to help but this is completely irellavent. My phony CAN'T get into recovery and it NO LONGER CAN even get into Odin (download mode). I guess I wasn't clear when posting. Is anyone aware of a hardbrick fix or if sammy will repair ,my phone for a price.

Hi buddy. The EXACT same happened to be when trying to flash RocketV16. Frozen charge screen and everything.
To sort it I first let the phone start and hang on the black/white writing splash screen, removed the battery while it was on, held down the power button without the battery in for 3-5 seconds, put the battery back in. I then held Vol Down, the Home button and then the power down button (hold down power last) for some seconds until the Odin-Mode downloader came up.
After that I just followed a guide on flashing with Odin.
No more £9999999999 brick

unfortunatly i cant try that stratagy because i cant even get to the splash screen anymore. + i gave it to a local guy who claims to be able to jtag it. If it doesnt work ill send it to samsung and of course pay because i voided my warrenty. oh well. better then my old i9000m.

Galaxy Note N7000 Screen
I hate to hijack your thread but what I have to ask directly relates to your issue.
I have been searching for any file that contains this actual GALAXY Note Boot Screen - I am looking for this image file with the hope of making this my sole wallpaper/background. If there is anyway you or those who are reading this can PLEASE attach the file or at the very least provide a link so I 'd be able to download it for myself. I'd sincerely appreciate any help I can get.
I'm willing to pay ANY PERSON WHO PROVIDES A HIGH QUALITY IMAGE HOPEFULLY ALREADY SIZED FOR IMMEDIATE USE.
I'm sorry - please don't take this message as that of "shouting", My hope was to capture readers attention. Again, I apologize in advance for anyone having taken this message as shouting. That was not my intent.
Jim

connection
hey,i don't get how u manage to transfer stock firmware into the phone when pc cannot detect any file from the note???is it using odin??if yes,may someone share how to connect the phone to the pc via odin??
---------- Post added at 07:37 PM ---------- Previous post was at 07:27 PM ----------
hey how you manage to upload rocket rom,my pc cannot detect any file from my phone..even simple window explorer does not turn up..i hope u may help me...

me too Stuck at Galaxy Note Boot Logo
dr.ketan said:
First Relax man, dont be in hurry, read this guide twice/thrice n calmly proceed...
It is nice still you can entre to download mode.
First get Stock firmware from here Type N700 in search field, it will show all available firmware, select you wish to flash n download
Note : If you select latest ROM KL7, you won't get Root + CWM, for that you have to Flash another ROM first, then You have to Root + CWM,then Install Mobile odin pro, now flash KL7 with Mobile Odin pro with 'ever root' option enable. If you selecting another ROM, ignore this note
Get odin n extract
Install:
Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly.
Extract tar file from the ROM you have download(password available at site from you have download). Put the phone into download mode (vol. down+home+power buttons),
Comlete close kies, if open. start odin, connect the phone via USB. Choose continue on the phone,
make sure that only two boxes are checked in odin - Auto Reboot and F.Reset Time.
Choose PDA button in Odin and select tar file you extracted before.
Choose START button.
The phone will reboot after the flash. Done.
Click to expand...
Click to collapse
Dr Ketan,I have mentioned the same in your other thread about stucking at Galaxy Note Boot Logo forver.
I was on CheckRom v6 and then i went to flash a kernel and then got stuck at Galaxy Note Boot Logo.
I am not able to got to recovery mode by pressing power+home and vol+,but I can go to Download mode by pressing power+home and vol-.so i went to desktop Odin and tried flashing one of the rom(Dr Ketan Guide to Rooting).Seems like Odin was succesful but still stuck at Galaxy Note Boot Logo.
please need help here,I hope my Galaxy Note is not Bricked!

Try flashing a cf root kernel back
Sent from my GT-N7000 using XDA

Remkve battery for few min, thn put it back n try to enter recovery
If you able to enter recovery wipe cache n wipe data, thn reflash rom with pc odin.
Sent from my GT-N7000 using xda premium

SGS plus i9001 - bricked?

I dont have CWM installed. I can join only in Download Mode,
I am trying to install via PDA file with ODIN 1.85 it said:
ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013>
<ID:0/013> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-------------------------------------
When I try with Odin 4.43 it stocked at
<1> setup connection...
I have changed USB port on PC, nothing yet.

Did You installed Kies?
On what system are You trying to flash the phone?
On XP ODIN is not working, I flashed my i9001 with CWM on Windows 7 with ODIN and installed Kies without any problems.

aXiDroid said:
Did You installed Kies?
On what system are You trying to flash the phone?
On XP ODIN is not working, I flashed my i9001 with CWM on Windows 7 with ODIN and installed Kies without any problems.
Click to expand...
Click to collapse
Hello,
- I think thats my problem. I will try via Windows7 when I am ready too. I will reply.
Thank you.

No problem, just don't rush.
Flashing CWM takes a minute, after that the phone will reboot.
To enter to Recovery mode press Volume Up + Power and keep it pressed for 2 seconds after Samsung logo will appear.
BTW: If you encounter boot loop don't panic, just clear cache, data and dalvik and everything will be ok. I fixed boot loop on my phone by doing so.
edit: could you please press the THANKS button if I helped?

Are you using a pit file if so one correct for your device
Sent via that ninja standing right behind you

sider pyrgeds
Latrop said:
Are you using a pit file if so one correct for your device
Sent via that ninja standing right behind you
Click to expand...
Click to collapse
Hi,
- Yes I am using PIT file also but it stock at 'setup connection' with odin 4.43
- With odin 1.85 it said fail by this logs as below:
<ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013>
<ID:0/013> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed

Make sure you run Odin as admin and also try uninstalling device through device manager whilst its connected don't click delete driver software then unplug and replug also make sure you have full firmware to install should be a few files not just PDA in my experience
Sent via that ninja standing right behind you

aXiDroid said:
No problem, just don't rush.
Flashing CWM takes a minute, after that the phone will reboot.
To enter to Recovery mode press Volume Up + Power and keep it pressed for 2 seconds after Samsung logo will appear.
BTW: If you encounter boot loop don't panic, just clear cache, data and dalvik and everything will be ok. I fixed boot loop on my phone by doing so.
edit: could you please press the THANKS button if I helped?
Click to expand...
Click to collapse
Hi,
I cant run right now into CWM there is no CWM installed. Also I dont have SD Card on phone, is this problem?

Pretty sure cwm is either part of kernel or in some devices installed to system
Sent via that ninja standing right behind you

Latrop said:
Make sure you run Odin as admin and also try uninstalling device through device manager whilst its connected don't click delete driver software then unplug and replug also make sure you have full firmware to install should be a few files not just PDA in my experience
Sent via that ninja standing right behind you
Click to expand...
Click to collapse
You are right but it wont.
I am tryin to install this package: I9001XXKP4
PDA(PDA FILE), PHONE(Modem file), CSC (CSC FILE), PIT(PIT FILE) and Boot_loader
but its the same it stock.

Don't do bootloader I'm pretty sure and how long did you leave it cause once it took 15mins setup connection for me if you still don't prevail only option is try another computer
Sent via that ninja standing right behind you

You are talking about ClockworkMod, yes?
It replace Samsung's Recovery, if You flash it with ODIN there is no way it wouldn't run. Just turn the phone as I wrote before: Vol UP + POWER, and keep them pressed for 2, 3 seconds after Samsung logo appears. This will take you to recovery mode, and by so to CWM.
I'm using "recovery-clockwork-5.5.0.4-ariesve.tar", but the latest one is: "CWM6012-TOUCH-CM9-recovery". As far as I know for this moment.

There is the same also with Windows7 it won't flash.

noc1 said:
There is the same also with Windows7 it won't flash.
Click to expand...
Click to collapse
Have You installed Kies?
Download the newest, with is 2.3.3. Install it, reboot, put the phone in to download mode, turn the ODIN, select the files, connect the phone and hit the START button.
No way this wont work! I did so many times.

aXiDroid said:
Have You installed Kies?
Download the newest, with is 2.3.3. Install it, reboot, put the phone in to download mode, turn the ODIN, select the files, connect the phone and hit the START button.
No way this wont work! I did so many times.
Click to expand...
Click to collapse
I have installed Kies from official Web download samsung.
I am going to reboot now. And I will run again.
Thank you.

Latrop said:
Don't do bootloader I'm pretty sure and how long did you leave it cause once it took 15mins setup connection for me if you still don't prevail only option is try another computer
Sent via that ninja standing right behind you
Click to expand...
Click to collapse
I have wait about 18mins it stockat Setup connection..

Have you try to flash simple rom file onto the phone? Or Are you flashing the PDA file?
With "One Package" there shouldn't be any issues.

aXiDroid said:
Have you try to flash simple rom file onto the phone? Or Are you flashing the PDA file?
With "One Package" there shouldn't be any issues.
Click to expand...
Click to collapse
it doesn't work
can you please find me someone some pda or One package files for flash

noc1 said:
it doesn't work
can you please find me someone some pda or One package files for flash
Click to expand...
Click to collapse
You can download original newest Samsung's package from www.samfirmware.com - just create an account.
Download depends on Your country.
Download the file, use ODIN and select "One Package". Aries file will be needed to.

noc1 said:
I dont have CWM installed. I can join only in Download Mode,
I am trying to install via PDA file with ODIN 1.85 it said:
ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013>
<ID:0/013> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-------------------------------------
When I try with Odin 4.43 it stocked at
<1> setup connection...
I have changed USB port on PC, nothing yet.
Click to expand...
Click to collapse
For i9001 please refer to your WIKI http://forum.xda-developers.com/wiki/Samsung_Galaxy_S_Plus/GT-I9001
you cannot use Odin 1.85, only Odin 4.43 with ariesVe.ops
IF "setup failed" in Odin its because KIES is running in system tray, you must shut it down for Odin to function
Open task manager and close:
Kies.exe
KiesTrayAgent.exe
KiesPDLR.exe
further reference refer to My Android Solutions link below

Help with brick please

Hey all,
As per title, A while back I rooted and installed a few custom roms on my unit before sticking with one named
"GT-7000_SweetROM_V11.1_LTA" and all was going well until a "super user" app update and a "low battery" met in the middle and my phone lost power and turned off.
Now my phone will not boot and freezes on the samsung logo, pressing vol up + power + home will, not bring up the recovery mode
but vol down + power + home will take me to a download screen, Odin, if my research is right.
I've read a few posts with the same symptoms as me but with different reasons for getting there in the first place and I'm unsure of what to do.
If my reading has been correct I'm not hard bricked but am in a bit of a spot and PC Odin can help me out, but then there are different versions of Odin as well.
Just some more bits and peices that I can think of to try and give you all as much info as possible. here goes,
I do remember Philz ???? something on my phone and was able to switch between roms by placing them on the external micro sd card and using vol up + power + home to navigate a menu.
Whilst writing this post I have had my unit plugged in via usb and it justs sits there with the battery icon showing but it shows no movement ie: the little cirle will not spin nor will the green charge level go up. Also it tried to install "mobi" something onto my pc.
Another problem I'm having is finding a valid download link for PC Odin any help there would be cool.
If you need anymore info I'll do my best but I'm very new to this, many thanks
E2A: have downloaded Odin and phone is reconized there just need to learn how to use the Prog

Download and flash PhilZ kernel 15.5 odin version. Flask on via odin (put it in pda tab and flash) and see if you can get your phone working again or can get into recovery. If not download and.flash whole stock jb rom. There is also a ltc rom odin version recently posted in one of the two dev threads.
As how to use odin for note, find the famous sticky thread by dr.ketan in our n7000 forum.
Sent from my GT-N7000 using Tapatalk 2

@rinksy55 you said low battery right? charge the battery first and then try to go to recovery and download mode.

forest1971 said:
Download and flash PhilZ kernel 15.5 odin version. Flask on via odin (put it in pda tab and flash) and see if you can get your phone working again or can get into recovery. If not download and.flash whole stock jb rom. There is also a ltc rom odin version recently posted in one of the two dev threads.
As how to use odin for note, find the famous sticky thread by dr.ketan in our n7000 forum.
Sent from my GT-N7000 using Tapatalk 2
Click to expand...
Click to collapse
thanks for the reply
I tried to flash "philz_touch_6.07.9-n7000.tar.md5" with Odin3 V1.87 and it failed
also tried "N7000XXLTC_MOD1.tar.md5" which also failed
treacherous_hawk said:
@rinksy55 you said low battery right? charge the battery first and then try to go to recovery and download mode.
Click to expand...
Click to collapse
Yeah low battery which doesnt seem to be charging acording to the widget but I can enter download mode whilst plugged in to usb but not recovery
just for info my phone acts the same wether plugged into comp or the wall socket with samsung hardware
guess Im screwed eh?
thanks

I would try a new battery.
Sent from my GT-N7000 using Tapatalk 2

I'm sure the battery is fine it's the phone thats mucked up, I've not had any problems to idicate my battery was failing
Are there any other avenues I could explore? I'm willing to get a new battery but then I could have 1 phone and 2 dead batteries and no way of charging.
When I tried flashing PhilZ kernel and the jb rom with Odin it was Odin that did its thing then reported to have failed, the phone had power to it the whole time and was showing the download screen with the message "do not turn off target".
thanks for you help so far
E2A Image
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}

Looks like problem with setting up connection. Drivers/USB/USB Cable/Ports/PC.

nokiamodeln91 said:
Looks like problem with setting up connection. Drivers/USB/USB Cable/Ports/PC.
Click to expand...
Click to collapse
Thanks for helping out :good:
Drivers are up to date, installed kies then uninstalled leaving the drivers behind.
USB, have used all the ports on my pc
Changed cable, used the wife's S3 cable
Ports, I can open ports easy, thought that was just router tho
PC, not sure what you mean there but running Win7 with decent spec.
Still the same outcome, fails on connection
thanks for taking the time tho

Try installing one from here
http://forum.xda-developers.com/showthread.php?p=49864289

nokiamodeln91 said:
Try installing one from here
http://forum.xda-developers.com/showthread.php?p=49864289
Click to expand...
Click to collapse
I saw that link earlier and tried 'PhilZ-cwm6-ZSLR1-OZS-5.11.2.tar.md5' and after reading your last post went back and tried 'PhilZ-cwm6-ZSLR1-OZS-5.11.2.tar.md5'
dont think its the rom heres the text from odin:
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> PhilZ-cwm6-DDLSC-ODD-5.11.2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
seems to be hanging on a connection

1. Install the latest drivers from: http://forum.xda-developers.com/showthread.php?t=961956/
2. Reboot
3. Disable all antiviruses
4. On your phone:
a) Boot into download mode
b) Plug your phone into your PC (only plug it into the USB 2.0 ports, don't do it on 3.0 or 1.1 or 1.0 etc.)
c) Follow the on screen instructions saying something along the lines of "Press volume up to continue" - you want to continue
d) Check whether Odin has detected your phone, if it has continue to step 5
5. Flash a stock ROM or kernel
6. If it succeeds, boot into recovery and perform a factory reset <= ONLY IF IT ISN"T ICS

OK.. Odin is not able to get to the PIT mappings.. There seems to be some connection issues. Check with newer version of Odin.. Also probably a different pc.
---------- Post added at 04:55 AM ---------- Previous post was at 04:52 AM ----------
Uninstall moboginie drivers as well completely.

XxPixX said:
1. Install the latest drivers from: http://forum.xda-developers.com/showthread.php?t=961956/
2. Reboot
3. Disable all antiviruses
4. On your phone:
a) Boot into download mode
b) Plug your phone into your PC (only plug it into the USB 2.0 ports, don't do it on 3.0 or 1.1 or 1.0 etc.)
c) Follow the on screen instructions saying something along the lines of "Press volume up to continue" - you want to continue
d) Check whether Odin has detected your phone, if it has continue to step 5
5. Flash a stock ROM or kernel
6. If it succeeds, boot into recovery and perform a factory reset <= ONLY IF IT ISN"T ICS
Click to expand...
Click to collapse
done all of this with same result, as soon as I try to flash ROM Odin waits a while then reports fail
Tried with latest version of Odin, 3.07 and that just sits at 'SetupConnection' in the dialog box
nokiamodeln91 said:
OK.. Odin is not able to get to the PIT mappings.. There seems to be some connection issues. Check with newer version of Odin.. Also probably a different pc.
---------- Post added at 04:55 AM ---------- Previous post was at 04:52 AM ----------
Uninstall moboginie drivers as well completely.
Click to expand...
Click to collapse
As above, tried with latest Odin, Odin3 v3.07 same result, uninstalled moboginie as well, dunno how that got on to my pc in the first place!!
Thanks for input guys

I got that mobogenie rubbish by accident once too, it came with daemon tools.
Can you perhaps try those steps on another computer?

XxPixX said:
I got that mobogenie rubbish by accident once too, it came with daemon tools.
Can you perhaps try those steps on another computer?
Click to expand...
Click to collapse
I do have an old lappy but it has Ubuntu installed and that drives me nuts lol, only other option is to put Odin plus Rom onto memory stick and visit a friend..
You said something about PIT and Ive seen some posts on it, I guess that roue is last resort?
really appreciate you help here

If there is a proper connection, then odin should be able to get the partition mapping from the phone and will be displayed as
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..

nokiamodeln91 said:
If there is a proper connection, then odin should be able to get the partition mapping from the phone and will be displayed as
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
Click to expand...
Click to collapse
and if I cant get a proper connection (I can't, Odin never gets past SetupConnection) Im doomed?

That's why try on a different pc.

Would a clean install of win7 work, I have spare hard drive I could try, I'm guessing youre thinking driver probs on my pc
thanks again

rinksy55 said:
Would a clean install of win7 work, I have spare hard drive I could try, I'm guessing youre thinking driver probs on my pc
thanks again
Click to expand...
Click to collapse
Yeah. That should do.