[Q] Galaxy Note Stuck at Boot Screen - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Hi I just decided to change my custom firmware to darkynote from rocketrom. It worked perfectly but I wanted to update my kernal also so afterwards i rebooted into recovery and installed version 2.6 of Abyss Note. Now My phone boots to the "Samsung Galaxy Note N7000" Screen and stays there unless i plug it in, then when i start it it goes to a frozen battery screen. I cant boot into recovery but i can boot into download mode. Can someone help me get my phone back to stock? I can't seem to find a tutorial anywhere that will work for me.
please help
edit: extra details, the Odin3 v1.85 process gets stopped at NAND Write Start!!
Here is the message feed:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKL7_N7000OXAKL7_N7000XXKL7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> factoryfs.img
<ID:0/006> NAND Write Start!!

Also tried using CF-Root kernal. no luck there. The Bar in Odin says KERNEL and the green bar is full, also stuck at NAND Write Start!!.
Someone respond, im gonna cry.

First Relax man, dont be in hurry, read this guide twice/thrice n calmly proceed...
It is nice still you can entre to download mode.
First get Stock firmware from here Type N700 in search field, it will show all available firmware, select you wish to flash n download
Note : If you select latest ROM KL7, you won't get Root + CWM, for that you have to Flash another ROM first, then You have to Root + CWM,then Install Mobile odin pro, now flash KL7 with Mobile Odin pro with 'ever root' option enable. If you selecting another ROM, ignore this note
Get odin n extract
Install:
Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly.
Extract tar file from the ROM you have download(password available at site from you have download). Put the phone into download mode (vol. down+home+power buttons),
Comlete close kies, if open. start odin, connect the phone via USB. Choose continue on the phone,
make sure that only two boxes are checked in odin - Auto Reboot and F.Reset Time.
Choose PDA button in Odin and select tar file you extracted before.
Choose START button.
The phone will reboot after the flash. Done.

Alright sounds good but i left it at the NAND write start thing overnight and when i came back it said this:
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Now I have a black screen and its flashing on and off with the frozen battery symbol. I think the battery is drained or something.
Also my download of the rom finished, there isnt any tar files its just a zip with an MD5 file and a Dll. Should i just but the MD5 file in the PDA section?
Edit: now my phone wont do anything when i try to put it in download mode.

Anyway if you are still able to entre Download mode, then try to flash stock kernel as i said above.

But thats what I mean, is it possible for the phone to not boot into download because the battery is dead or is my phone just bricked forever $850 dollars out the window.

tangelos said:
I cant boot into recovery but i can boot into download mode.
Click to expand...
Click to collapse
Actually i dont understand properly, your first post said U R getting into DW mode, if you can entre into boot mode, i guide you earlier, i cant say it bricked.
many time this happen after some error in procedure.
If you even not able to entre into Download mode, you need to entre it with JIG.

dr.ketan said:
Actually i dont understand properly, your first post said U R getting into DW mode, if you can entre into boot mode, i guide you earlier, i cant say it bricked.
many time this happen after some error in procedure.
If you even not able to entre into Download mode, you need to entre it with JIG.
Click to expand...
Click to collapse
Actually I was just updating you. At first it was working, then i tried a tutorial simmilar then the one you just gave me and it caused the phone to not turn on whatsoever. Can you link me to one of these "jigs". Thanks

You can get it readymade from market e.g. ebay or you can make it own home made
see here http://forum.xda-developers.com/showthread.php?t=819551
better first try with other battery once, if you cud manage

I was able to get a hold of one locally. When I plug it in, nothing happens. Any advice? Its for a GSII. Is that why? Or is it the battery thing. Before it stopped working completely, when i booted into download it would say low battery. Looks like its game over for my new phone .

I tried this with an old usb cable http://forum.xda-developers.com/showthread.php?p=20914895#post20914895.
Inserted the USB Jig afterwards. No luck
I suppose i have to take it to be J-tagged: http://toronto.kijiji.ca/c-buy-and-...-JTag-Service-Phone-Unlock-W0QQAdIdZ341742939

I'm sorry if this is not helping, or being so late, but I wanted to share my experience.
So, now can you enter the recovery menu by pressing the 3 buttons?
if you can then do a factory reset/wipe from the recovery and then flash an entire flashable ROM, maybe a stockROM or ROCKETROM.
you can upload ROCKETrom from the ordinary windows explorer , just copy and paste to the ex.SD.
the looping android animation actually happened to mine, and that's how I fixed it.
BTW: I didn't use Odin at all, or any other program.

Thanks for trying to help but this is completely irellavent. My phony CAN'T get into recovery and it NO LONGER CAN even get into Odin (download mode). I guess I wasn't clear when posting. Is anyone aware of a hardbrick fix or if sammy will repair ,my phone for a price.

Hi buddy. The EXACT same happened to be when trying to flash RocketV16. Frozen charge screen and everything.
To sort it I first let the phone start and hang on the black/white writing splash screen, removed the battery while it was on, held down the power button without the battery in for 3-5 seconds, put the battery back in. I then held Vol Down, the Home button and then the power down button (hold down power last) for some seconds until the Odin-Mode downloader came up.
After that I just followed a guide on flashing with Odin.
No more £9999999999 brick

unfortunatly i cant try that stratagy because i cant even get to the splash screen anymore. + i gave it to a local guy who claims to be able to jtag it. If it doesnt work ill send it to samsung and of course pay because i voided my warrenty. oh well. better then my old i9000m.

Galaxy Note N7000 Screen
I hate to hijack your thread but what I have to ask directly relates to your issue.
I have been searching for any file that contains this actual GALAXY Note Boot Screen - I am looking for this image file with the hope of making this my sole wallpaper/background. If there is anyway you or those who are reading this can PLEASE attach the file or at the very least provide a link so I 'd be able to download it for myself. I'd sincerely appreciate any help I can get.
I'm willing to pay ANY PERSON WHO PROVIDES A HIGH QUALITY IMAGE HOPEFULLY ALREADY SIZED FOR IMMEDIATE USE.
I'm sorry - please don't take this message as that of "shouting", My hope was to capture readers attention. Again, I apologize in advance for anyone having taken this message as shouting. That was not my intent.
Jim

connection
hey,i don't get how u manage to transfer stock firmware into the phone when pc cannot detect any file from the note???is it using odin??if yes,may someone share how to connect the phone to the pc via odin??
---------- Post added at 07:37 PM ---------- Previous post was at 07:27 PM ----------
hey how you manage to upload rocket rom,my pc cannot detect any file from my phone..even simple window explorer does not turn up..i hope u may help me...

me too Stuck at Galaxy Note Boot Logo
dr.ketan said:
First Relax man, dont be in hurry, read this guide twice/thrice n calmly proceed...
It is nice still you can entre to download mode.
First get Stock firmware from here Type N700 in search field, it will show all available firmware, select you wish to flash n download
Note : If you select latest ROM KL7, you won't get Root + CWM, for that you have to Flash another ROM first, then You have to Root + CWM,then Install Mobile odin pro, now flash KL7 with Mobile Odin pro with 'ever root' option enable. If you selecting another ROM, ignore this note
Get odin n extract
Install:
Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly.
Extract tar file from the ROM you have download(password available at site from you have download). Put the phone into download mode (vol. down+home+power buttons),
Comlete close kies, if open. start odin, connect the phone via USB. Choose continue on the phone,
make sure that only two boxes are checked in odin - Auto Reboot and F.Reset Time.
Choose PDA button in Odin and select tar file you extracted before.
Choose START button.
The phone will reboot after the flash. Done.
Click to expand...
Click to collapse
Dr Ketan,I have mentioned the same in your other thread about stucking at Galaxy Note Boot Logo forver.
I was on CheckRom v6 and then i went to flash a kernel and then got stuck at Galaxy Note Boot Logo.
I am not able to got to recovery mode by pressing power+home and vol+,but I can go to Download mode by pressing power+home and vol-.so i went to desktop Odin and tried flashing one of the rom(Dr Ketan Guide to Rooting).Seems like Odin was succesful but still stuck at Galaxy Note Boot Logo.
please need help here,I hope my Galaxy Note is not Bricked!

Try flashing a cf root kernel back
Sent from my GT-N7000 using XDA

Remkve battery for few min, thn put it back n try to enter recovery
If you able to enter recovery wipe cache n wipe data, thn reflash rom with pc odin.
Sent from my GT-N7000 using xda premium

Related

Galaxy Tab dead!

Hallo,
sorry for my bad English. I have translate my Problem with promt . I have flash my Tab with JM6. After the flash my Tab do not boot. On the tab is a picture, a yellow triangle and a PC are indicated. Get with Odin 3 1.7 following error message.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Have you tried recovery
Sent from my GT-I9000 using XDA App
thank you for your answer.
no, what must i do?
wheel14 said:
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Click to expand...
Click to collapse
after you're flashing with Odin, then restating automatic in download mode, press the power button for 10 seconds (until tab will switch off), then restart by pressing the power button together with volume up. wait until finishing installing of CSC and then will restart by it self.
check my tread
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
wheel14 said:
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
Click to expand...
Click to collapse
I had the same situation, just take a look here. try to don't panic... try to follow my steps described in the tread and you might be succeed. I hope it help
I do not look though there sorry. I am in panic..which step....is the right?
i have flash the pit-file only. ist this right? and now?
wheel14 said:
I do not look though there sorry. I am in panic..which step....is the right?
Click to expand...
Click to collapse
try to look here and here
thank you.. I have flah the pit File only. now i will flash the pda without the pit. re-partition will be not selected. is this right. thank you for your help
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
wheel14 said:
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
Click to expand...
Click to collapse
I can't get you....can you describe a little what have you done? you're saying that you flash the firmware with Odin, right? and then? have you restarted in recovery mode? or you boot the phone loading the OS.....you should restart directly in recovery mode in order to finalize the installation of PDA and CSC....
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
wheel14 said:
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
Click to expand...
Click to collapse
Welcome back in our family.
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Go to samfirmware.com download the files for your device.
Select pit file then check repartition - flash
Select pda csc modem, uncheck repartition - flash.
Good luck! If you get any trouble send me a msg. on skype luc_de_mar
khatypically said:
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Click to expand...
Click to collapse
Sent from my GT-P1000 using XDA App
Thanks Lucian, This is exactly what I did in the first place. Used Odin 1.7 and applied the PIT file coming with it, then applied the P1000JPJM5 PDA and CSC modem file.
Unless the P1000JPJM5 is not for my device?? How to know?
Lucian, any clue?
My tab is dead after I tried to install an arabic firmware from samfirware.com. I bought my tab originally from the US. Now, I'll download the "suitable" firmware from samfirmware.com as you advised, but How would I ever know the suitable firmware given that my device is exactly this one (that's where I bought)(my devise is dead now and can only display the download mode):
www .amazon. com /GALAXY-TAB-P1000-16GB-UNLOCKED/ dp /B004AKOVIS/ ref=sr_1_1?ie=UTF8&s=electronics&qid=1305378100&sr=8-1
Regards,
Khatypically, alive with a zoombie tab
totally unresponsive tab
I have been searching around forums looking for advice and have been unable to locate a solution so here seems as good a place as any to ask for help. I have an unlocked gtp-1000 that has been running overcome 1.4.5 for last month very nicely until tonight when I thought it would be a good idea to get some gingerbread goodness like I have been using on my nexus one. was going to flash Overcome ROM v2.0.0 BETA 2 and was following guide but only got halfway through flashing stock gingerbread with odin when laptop unexpectedly did a restart for an unknown reason while I was away getting a snack. was unsure whether flashing process had been completed so opened odin again and tried reflashing. couldnt get past
setup connection...
so tried to reboot into download mode and then powered down. now tab is dead. battery was at 80% when it died
before I take back to samsung tomorrow any ideas?
I have plugged into wall charger= nothing
plugged into laptop=nothing and not detected
held power and volume up=nothing
held power and volume down=nothing
held power and volume up & home=nothing
no sounds or anything at all on screen
truly bricked?
Updates:
Hi Guys,
I applied the p1000nubjm2 firmware. I downloaded it from samfirmware. It's the latest P1000L firmware for America/Australia. It failed in the PDA file: P1000NUBJM2_P1000NUBJM2_P1000NUUBJM2_HOME.TAR . I was planning to apply the gingerbread update after that.
Now to the results, As you know, before, I was able to reach the download mode, the startup Galaxy Tab/Samsung screen, and the battery displays when connecting the cable. Now, after application of this lovely firmware and failure, nothing (literally "Nothing") takes place. The device became more dead than it was before . It doesn't display anything and it doesn't respond to power or displays the battery. It became a black $500 cost brick No matter how much time I keep it charging (or what "should be" charging), it would never startup again (sigh!) The ODIN and samsung kies no more recognize the device when connected to the computer.
Any additional clues before I decide to convert it to a teacup base?
Regards,
ARK

[Q] I think I just bricked my phone?

Beat with me guys, I am very very new to this board, and I apologize if I post this in the wrong area.
Lemme start from scratch.
My phone is not rooted or anything like that. BUT I wanted to update my software for the Captivate to 2.2 using samsung Kies.
Not sure what happened, I though I had the correct drivers installed and what not, but it gave me the screen with the phone, exlamation mark, and computer.
I can put my phone into download mode, and I installed odin3 one click downloader. The problem is, when it gets to the part 'file analysis' it gets stuck there.
I watched a video on youtube and his went automatically, so I'm not sure at ALL what to do. If I can fix this myself, I'd love to. If not, I will go through AT&T and see if I can get it replaced.
Any help would be greatly appreciated.
Not sure how to fix it, but if you have to send it into samsung say it got screwed up somehow while trying to update to KB1, in truth that is what happened, plus if you say that they will try to fix it fast
If you have access to another computer, download ODIN and try it on that one. Odin works on my laptop but not on my desktop.
CM7 Inspire 4G
What you have is a soft brick. Keep trying to get into download (try both 2 and 3 button methods) and then retry Odin. Look in Dev subforum for the "How to flash a ROM" sticky as there is good info on how to do this.
Samsung was absolutely no help lol.
Well.. I guess I can try this on another desktop.
Jeez I regret trying to upgrade man. Shoulda waited and learned more.
Has anyone had odin3 get stuck at file analysis before?
What model is your Cappy? You can find the model number underneath the battery (on the phone itself). It should have a number like 1006,1007,1008,1009,1010,etc.
Also, it'll be a good idea to try this alternate method in the mean time:
Make sure you know how to go to Download Mode, and that you have the drivers installed properly.
Windows 64bit
Windows 32bit
This is the manual (or "full") Odin, it's taken from a post by icezar1 in the Development Forum:
Do not use this if you want to send your phone back to ATT or Samsung for warranty!
Do not use this if you know you flashed a -LOW- ODIN package (when opening the PDA***.tar or CODE***.tar you will find inside boot.bin or sbl.bin)
Use this if you want to go back to stock before flashing a custom ROM.
Use this without worries if you changed your boot screen image or if you flashed the secondary boot loader which allows you to enter download/recovery with key combos.
Download the package from here
How to:
Remove sdcard and SIM card from the phone
Extract JF6_secure.zip somewhere.
Boot your phone in Download Mode
Run Odin3 v1.3.exe
Plug in your phone via USB
Click on the button PDA
Choose JF6_secure.tar.md5
Click start
Wait and do not unplug cable until it is finished
venomio said:
What model is your Cappy? You can find the model number underneath the battery (on the phone itself). It should have a number like 1006,1007,1008,1009,1010,etc.
Click to expand...
Click to collapse
Just for clarity sake, those are not the model numbers, they are build date (first two are year, second two are month). The model number of the Captivate is i896 or i897.
I know, I keep saying that they're model number though for some reason. Thanks anyway I guess.
Thank you venomio this 1.3 is working much better.
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> Enter CS for MD5..
<ID:0/003> Check MD5.. Do not unplug the cable..
<ID:0/003> Please wait..
<ID:0/003> Checking MD5 finished Sucessfully..
<ID:0/003> Leave CS..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
That's where I'm at right now. Fingers crossed!!
aftermaz said:
Beat with me guys, I am very very new to this board, and I apologize if I post this in the wrong area.
Lemme start from scratch.
My phone is not rooted or anything like that. BUT I wanted to update my software for the Captivate to 2.2 using samsung Kies.
Not sure what happened, I though I had the correct drivers installed and what not, but it gave me the screen with the phone, exlamation mark, and computer.
I can put my phone into download mode, and I installed odin3 one click downloader. The problem is, when it gets to the part 'file analysis' it gets stuck there.
I watched a video on youtube and his went automatically, so I'm not sure at ALL what to do. If I can fix this myself, I'd love to. If not, I will go through AT&T and see if I can get it replaced.
Any help would be greatly appreciated.
Click to expand...
Click to collapse
I'm in the same exact situation as the OP. I'll try the instructions posted below and report my findings.
check your build number first before you flash using odin. certain build may not work with odin one-click.
an usb jig will help you out if you cannot get into the download mode or just in case:
http://cgi.ebay.com/ws/eBayISAPI.dl...84198&ssPageName=STRK:MESELX:IT#ht_782wt_1139

Firmware upgrade encountered an issue Message.

Hello, guys.
I was trying to install a new rom to my Galaxy Note. and when wiping out the user data (to get the phone ready to install the new rom) he phone reboot and got stuck on the start up logo. Waited for a long time but it didn't do any thing. So a remove the baterry and turned it back on. But but it did the same.
I then decided to flash it using Odin but it got stuck almost at the end of the proccess. Now my battery is almost dead and the only thing on the screen is a flashing message. Firmware upgrade encounter an issue.
HELP!!! THIS IS MY NEW PHONE!!!!
estebandilone said:
Hello, guys.
I was trying to install a new rom to my Galaxy Note. and when wiping out the user data (to get the phone ready to install the new rom) he phone reboot and got stuck on the start up logo. Waited for a long time but it didn't do any thing. So a remove the baterry and turned it back on. But but it did the same.
I then decided to flash it using Odin but it got stuck almost at the end of the proccess. Now my battery is almost dead and the only thing on the screen is a flashing message. Firmware upgrade encounter an issue.
HELP!!! THIS IS MY NEW PHONE!!!!
Click to expand...
Click to collapse
Which rom you were on before trying to flash? And what did you try to install?
Sent from my GT-N7000 using xda premium
I was on Android 4.0.3 the German realesed.
N7000XXLPY---------4.0.3---------2012 May
I downloaded it from the forum and it was working nicely. I just wanted to try a different rom. But I didn't get to do nothing just to clear the data which never ended and crash my phone..
Stuck after wiping user data, Odin hanging at the end..where exactly did it stop working?
I'd say that it's definitely superbricked.
you can do that:
- go on recovery (Try vol up + home + power)
- mount usb storage and put abyss kernel in a directory
- flash abysskernell4.00
- reboot recovery
- wipe data cache and dalvik
- power off
- power on
if it's stay on boot logo :
- power off
- vol down + home + power (download mode)
- flash your note with odin pc with this method
- dl mobil odin and flash ics open germany with this method
Noizy.
I will try that, but now i have to charged my battery to be able to do it.
When trying to flash the green bar on Odin gets almost to the end ot the proccess but then it just sits there and doesn't do anything...
estebandilone said:
I will try that, but now i have to charged my battery to be able to do it.
When trying to flash the green bar on Odin gets almost to the end ot the proccess but then it just sits there and doesn't do anything...
Click to expand...
Click to collapse
Could you paste the Odin log perhaps? That would help the people around here give you a solution, if any.
Right now I am downloading the files from the commment above... I will try that and post whatever it happened!!! My internet conection is just a Mega so it takes me a while to download all the files to try it... But I am almost done!!
This is what I have on Odin. It almost get to the end of the green bar.
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Get PIT for mapping..
<ID:0/012> Firmware update start..
<ID:0/012> factoryfs.img
<ID:0/012> NAND Write Start!!
This is the message Showing..
Is your LPY Rom rooted? If yes, then how?
Did you flash CF-Root LPY kernel, or did you root it using Dr.Ketan's method?
This is a screen shot of the screen.
Yes it's rooted and I used Dr.Ketan's method..
I'm afraid you have a brick on your hands, mate. Take your Note to the
nearest service centre for MoBo replacement.
That I can't do. I bought from a third person... So I don't have any warranty... Let me ask you a question. The fact that I can get into recovery mode doesn't make a difference?
estebandilone said:
This is a screen shot of the screen.
Click to expand...
Click to collapse
Duno if this method will work for u but it works for me n my friend...
1stly i pressume u are able to boot into download mode...
2ndly, d/l a rooted GB Rom...
3rdly, restart pc/lappy
4thly, change another USB port (changed port works for me n my friend)
5thly, fire up PC Odin... put Note into download mode n connect...
Lastly select the rooted GB rom under "PDA"..
keep finger cross
Noted From My G.NOTE Using XDA Premium
I am trying again.
Not working... Don't know what to do
It's superbricked, for sure. All you can do is send it for repairs - motherboard replacement.
[Solve on [email protected]] Similar Case for reference
estebandilone said:
Not working... Don't know what to do
Click to expand...
Click to collapse
Hey dude, I had a similar case when I was upgrading my S2 officially because my USB was loose, I got the update 60% and came to a halt, my phone wasn't even rooted by then.
Here's what I did and here's what you can try:
1. root my phone (for your case, re-root your phone or even unroot then re-root it again, there may be some files damaged when your phone lost power).
2. install original kernel and Stock ROM (there might be original files which are needed from the original to make things work when you switch ROMs)
3. reboot and see if things are fine.
If you get back to running normal, then you can install whatever Custom ROMs you like.
Hope this help! Get back to me with the latest situation.

Suddenly cant boot my phone, or get into recovery

Hello gentlement. I have an Galaxy S I9000, and i have used a custom rom for about 2-3 months, unfortunately i can't remember which one, and as i cant boot my phone, im not sure how i can find out. I flashed it using Odin and Clockwork mod, both of which worked great. The problem now started out with me not being able to start my phone while charging, didn't pay much attention to it and just waited until it was charged, or unplugged it, started it, then charged it while it was on.
Now im having a different problem. I cant start my phone, the startscreen just says "Samsung galaxy S" etc, and it tries to reboot again and again.
I can start the phone into "download mode", but recovery mode doesnt seem to work.
Since the rom has been working flawlessly in the past, im not sure its the roms "fault"; might just be my phone singing on it's last verse.
Does anybody know what can cause this, or have a fix i can do in download mode?
I think i have read all the necesarry stickies, if i've missed something i apologize.
Thanks for all responses, regards - superegge
When this happens on ICS I reflash a kernel through odin in download mode and then reflash the ROM.
If your ROM is non wipe you could try this, otherwise I'd just try flashing a kernel and see if it boots.
superegge said:
Does anybody know what can cause this, or have a fix i can do in download mode?
Click to expand...
Click to collapse
First power down, remove battery, remove sim card and EXT SD card, preess power button for a min, reinsert battery and power it....
If still the same, flash a pit file as per guide given in Quick Fixes link below
xsenman said:
First power down, remove battery, remove sim card and EXT SD card, preess power button for a min, reinsert battery and power it....
If still the same, flash a pit file as per guide given in Quick Fixes link below
Click to expand...
Click to collapse
Thank you both for responses. I've tried following your guide many times now, installed odin etc. But everytime i try to flash my phone, this happens:
<ID:0/007> Added!!
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> Removed!
Sometimes it gets to some zImage thing, but my device is still "removed" shortly after. Is it maybe a faulty cable?
Will check back in tomorrow, need to sleep now. Again, thanks for your help
superegge said:
Sometimes it gets to some zImage thing, but my device is still "removed" shortly after. Is it maybe a faulty cable?
Will check back in tomorrow, need to sleep now. Again, thanks for your help
Click to expand...
Click to collapse
yep, it could be due to cable or mostly the PC, try on lap top or another PC, added concerning this to Quick fixes, take a rest first,
ive had the same problem with Odin. But that had to do with rooting, and the oneclick superuser program.
Hopefully it will work when you try on a new pc. Good luck superegge!

[Q] Please Help.. Galaxy Ace S5830 Not even turning on.

My Samsung Galaxy ace S5830 was running fine on a custom rom (cm11).
But then i flashed a new rom(WP) from the thread - http://forum.xda-developers.com/showthread.php?t=2140510 .
I am sure i followed the instructions mentioned in that thread.
After completion of flashing the zip file my phone turned off and dint boot up.
I tried to get into recovery mode ,but the phone dint even turn on.
I removed the battery ,charged it fully and tried getting into download mode (using 3 buttons),just with a hope to get back to stock rom using ODIN. But the Phone wont even tun on,i mean the screen wont even get on :crying: (No samsung logo ,No recovery mode,No download mode- nothing).
Now what should i do. ??? and will a usb jig help me out ??
rgr117 said:
My Samsung Galaxy ace S5830 was running fine on a custom rom (cm11).
But then i flashed a new rom(WP) from the thread - http://forum.xda-developers.com/showthread.php?t=2140510 .
I am sure i followed the instructions mentioned in that thread.
After completion of flashing the zip file my phone turned off and dint boot up.
I tried to get into recovery mode ,but the phone dint even turn on.
I removed the battery ,charged it fully and tried getting into download mode (using 3 buttons),just with a hope to get back to stock rom using ODIN. But the Phone wont even tun on,i mean the screen wont even get on :crying: (No samsung logo ,No recovery mode,No download mode- nothing).
Now what should i do. ??? and will a usb jig help me out ??
Click to expand...
Click to collapse
You're basically in the same position as me. Try this it nearly helped me: Take out phone battery, start odin with phone plugged in (battery still out) and load the files you need, hold the 3 button combo for recovery and insert battery whilst still holding the buttons (may need a second pair of hands to help), the phone should now be recognised by odin so hit start. For me it stuck at "setup connection" but you may be luckier. Also i had to hold volume up + down, home and power to get mine to recognise, you may need to do the same. If that don't work you're only option is to try the jig. There's no guarantee though. Good luck and let us know what happens cos i've gotta get a jig but i dont even have a spare couple of quid at the mo
rgr117 said:
My Samsung Galaxy ace S5830 was running fine on a custom rom (cm11).
But then i flashed a new rom(WP) from the thread - http://forum.xda-developers.com/showthread.php?t=2140510 .
I am sure i followed the instructions mentioned in that thread.
After completion of flashing the zip file my phone turned off and dint boot up.
I tried to get into recovery mode ,but the phone dint even turn on.
I removed the battery ,charged it fully and tried getting into download mode (using 3 buttons),just with a hope to get back to stock rom using ODIN. But the Phone wont even tun on,i mean the screen wont even get on :crying: (No samsung logo ,No recovery mode,No download mode- nothing).
Now what should i do. ??? and will a usb jig help me out ??
Click to expand...
Click to collapse
AFAIK CM7.x require CWM5.x... so maybe CWM 6.x is incompatible ...mmm i didn't test it but it could be :weird:
same here!! Stuck at "setup connection"
Way333 said:
You're basically in the same position as me. Try this it nearly helped me: Take out phone battery, start odin with phone plugged in (battery still out) and load the files you need, hold the 3 button combo for recovery and insert battery whilst still holding the buttons (may need a second pair of hands to help), the phone should now be recognised by odin so hit start. For me it stuck at "setup connection" but you may be luckier. Also i had to hold volume up + down, home and power to get mine to recognise, you may need to do the same. If that don't work you're only option is to try the jig. There's no guarantee though. Good luck and let us know what happens cos i've gotta get a jig but i dont even have a spare couple of quid at the mo
Click to expand...
Click to collapse
So, sorry for the late reply. My phone was not even getting detected by Odin in my friends laptop.
I gave up all the hopes,but then i just wanted to give it another try.
Tried the same trick,and this time,Odin detected my ace .
Now, the things is,the flashing process isn't going any further
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXMC1_S5830iODDLK1_RST_S5830iDDMC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
Been 10 minutes already ..Nothing happened ..
rgr117 said:
My Samsung Galaxy ace S5830 was running fine on a custom rom (cm11).
But then i flashed a new rom(WP) from the thread - http://forum.xda-developers.com/showthread.php?t=2140510 .
I am sure i followed the instructions mentioned in that thread.
After completion of flashing the zip file my phone turned off and dint boot up.
I tried to get into recovery mode ,but the phone dint even turn on.
I removed the battery ,charged it fully and tried getting into download mode (using 3 buttons),just with a hope to get back to stock rom using ODIN. But the Phone wont even tun on,i mean the screen wont even get on :crying: (No samsung logo ,No recovery mode,No download mode- nothing).
Now what should i do. ??? and will a usb jig help me out ??
Click to expand...
Click to collapse
Hi There,
Well your device has bricked n that too Hard Bricked i,e No Recovery No Download.
A Usb JiGG may help you out.

Categories

Resources