Hallo,
sorry for my bad English. I have translate my Problem with promt . I have flash my Tab with JM6. After the flash my Tab do not boot. On the tab is a picture, a yellow triangle and a PC are indicated. Get with Odin 3 1.7 following error message.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Have you tried recovery
Sent from my GT-I9000 using XDA App
thank you for your answer.
no, what must i do?
wheel14 said:
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Click to expand...
Click to collapse
after you're flashing with Odin, then restating automatic in download mode, press the power button for 10 seconds (until tab will switch off), then restart by pressing the power button together with volume up. wait until finishing installing of CSC and then will restart by it self.
check my tread
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
wheel14 said:
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
Click to expand...
Click to collapse
I had the same situation, just take a look here. try to don't panic... try to follow my steps described in the tread and you might be succeed. I hope it help
I do not look though there sorry. I am in panic..which step....is the right?
i have flash the pit-file only. ist this right? and now?
wheel14 said:
I do not look though there sorry. I am in panic..which step....is the right?
Click to expand...
Click to collapse
try to look here and here
thank you.. I have flah the pit File only. now i will flash the pda without the pit. re-partition will be not selected. is this right. thank you for your help
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
wheel14 said:
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
Click to expand...
Click to collapse
I can't get you....can you describe a little what have you done? you're saying that you flash the firmware with Odin, right? and then? have you restarted in recovery mode? or you boot the phone loading the OS.....you should restart directly in recovery mode in order to finalize the installation of PDA and CSC....
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
wheel14 said:
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
Click to expand...
Click to collapse
Welcome back in our family.
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Go to samfirmware.com download the files for your device.
Select pit file then check repartition - flash
Select pda csc modem, uncheck repartition - flash.
Good luck! If you get any trouble send me a msg. on skype luc_de_mar
khatypically said:
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Click to expand...
Click to collapse
Sent from my GT-P1000 using XDA App
Thanks Lucian, This is exactly what I did in the first place. Used Odin 1.7 and applied the PIT file coming with it, then applied the P1000JPJM5 PDA and CSC modem file.
Unless the P1000JPJM5 is not for my device?? How to know?
Lucian, any clue?
My tab is dead after I tried to install an arabic firmware from samfirware.com. I bought my tab originally from the US. Now, I'll download the "suitable" firmware from samfirmware.com as you advised, but How would I ever know the suitable firmware given that my device is exactly this one (that's where I bought)(my devise is dead now and can only display the download mode):
www .amazon. com /GALAXY-TAB-P1000-16GB-UNLOCKED/ dp /B004AKOVIS/ ref=sr_1_1?ie=UTF8&s=electronics&qid=1305378100&sr=8-1
Regards,
Khatypically, alive with a zoombie tab
totally unresponsive tab
I have been searching around forums looking for advice and have been unable to locate a solution so here seems as good a place as any to ask for help. I have an unlocked gtp-1000 that has been running overcome 1.4.5 for last month very nicely until tonight when I thought it would be a good idea to get some gingerbread goodness like I have been using on my nexus one. was going to flash Overcome ROM v2.0.0 BETA 2 and was following guide but only got halfway through flashing stock gingerbread with odin when laptop unexpectedly did a restart for an unknown reason while I was away getting a snack. was unsure whether flashing process had been completed so opened odin again and tried reflashing. couldnt get past
setup connection...
so tried to reboot into download mode and then powered down. now tab is dead. battery was at 80% when it died
before I take back to samsung tomorrow any ideas?
I have plugged into wall charger= nothing
plugged into laptop=nothing and not detected
held power and volume up=nothing
held power and volume down=nothing
held power and volume up & home=nothing
no sounds or anything at all on screen
truly bricked?
Updates:
Hi Guys,
I applied the p1000nubjm2 firmware. I downloaded it from samfirmware. It's the latest P1000L firmware for America/Australia. It failed in the PDA file: P1000NUBJM2_P1000NUBJM2_P1000NUUBJM2_HOME.TAR . I was planning to apply the gingerbread update after that.
Now to the results, As you know, before, I was able to reach the download mode, the startup Galaxy Tab/Samsung screen, and the battery displays when connecting the cable. Now, after application of this lovely firmware and failure, nothing (literally "Nothing") takes place. The device became more dead than it was before . It doesn't display anything and it doesn't respond to power or displays the battery. It became a black $500 cost brick No matter how much time I keep it charging (or what "should be" charging), it would never startup again (sigh!) The ODIN and samsung kies no more recognize the device when connected to the computer.
Any additional clues before I decide to convert it to a teacup base?
Regards,
ARK
Related
I woke up this morning and my phone won't turn on! I hold down power and see the Samsung splash screen... then the display goes off and nothing happens. I can't launch into recovery mode... I can launch into Download Mode, but can't do anything from there... (no response to any buttons)
I tried pulling out the battery and SIM - to no avail...
I am running a rooted Bell phone with the lag fix.
Please give me suggestions! What do I need to do to recover this using my PC and adb?
Time to recharge your SGS?
Before i give you the bad news
try Flashing the phone with Odin, see if you can complete a successful flash
However you'll most likely see an Odin error concerning mounting the drive, your Internal SD drive is most likely dead, and it'll need to be replaced by Samsung/Bell service center.
there are many known cases like this related to the lag fix
slaman said:
I woke up this morning and my phone won't turn on! I hold down power and see the Samsung splash screen... then the display goes off and nothing happens. I can't launch into recovery mode... I can launch into Download Mode, but can't do anything from there... (no response to any buttons)
I tried pulling out the battery and SIM - to no avail...
I am running a rooted Bell phone with the lag fix.
Please give me suggestions! What do I need to do to recover this using my PC and adb?
Click to expand...
Click to collapse
atan.ismail said:
Time to recharge your SGS?
Click to expand...
Click to collapse
It's fully charged... it was charging all night. What's weird is that I've plugged it in and it's flashing the battery symbol.... I can't turn off the screen - it keeps flashing this symbol
slaman said:
It's fully charged... it was charging all night. What's weird is that I've plugged it in and it's flashing the battery symbol.... I can't turn off the screen - it keeps flashing this symbol
Click to expand...
Click to collapse
if you hold the power button, does it turn on at all?
how far does it go into the boot process?
does it get stuck after the pretty Galaxy S swirling logo?
AllGamer said:
if you hold the power button, does it turn on at all?
how far does it go into the boot process?
does it get stuck after the pretty Galaxy S swirling logo?
Click to expand...
Click to collapse
I don't get the swirling logo... I just get the static splash page "Samsung Galaxy S" - it stays for about a second, then the screen goes black.
I'm trying to figure out what to do once I'm in download mode... I have Samsung Kies (which won't detect it...) and Odin (which won't detect it)
slaman said:
I don't get the swirling logo... I just get the static splash page "Samsung Galaxy S" - it stays for about a second, then the screen goes black.
I'm trying to figure out what to do once I'm in download mode... I have Samsung Kies (which won't detect it...) and Odin (which won't detect it)
Click to expand...
Click to collapse
that doesn't sounds right
try installing Odin on another machine
seems like the PC you are trying to use has the USB port locked up.
i've had that happen on mine before
if you turn off the PC, remove the power cord
power it on, then put the power cord
and power it on again
that should reset it
Ok, Odin seems to recognize the phone (it installed all the drivers when it was in Download Mode) - I clicked "start" and got the following:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> Removed!!
then the phone went back into the flashing battery symbol... I need to grab the official Bell Samsung Galaxy S .pit file I guess.
Samsung Kies just sat there trying to connect when the phone was in Download Mode...
Okay, so I've downloaded the 0803.pit file... I just need to know which firmware to flash it with under PHONE, PDA, CSC, and DUMP...
Would really appreciate the help!
JH2 firmware for all 3 and flash with correct pit file and click partition (but will wipe all data).
rmanaudio said:
JH2 firmware for all 3 and flash with correct pit file and click partition (but will wipe all data).
Click to expand...
Click to collapse
I found the thread for JH2, but none of the links in it work!
http://forum.xda-developers.com/showthread.php?t=755063
Got one that you can spare?
Also, 0803.pit works for JH2 right?
Really appreciate your help!
I'm just going to try to find JG9 and upgrade via Samsung Kies... that's if I can find JG9 - these are so hard to find!
Hi Mate,
I just had the same problem - could not reboot from normal recovery, could not reboot from clockworkmod recovery. I had to launch nandroid recovery.
On my unit, it seems that the problem was caused by a conflict between setcpu profiles and the alter minfree settings from ryanza's oclf.
If you have clockworkmod installed and have backed up your rom, you should be able to use nandroid recovery.
I have now changed setcpu not to run on boot, and have not used alter minfree - prob seems to be sorted.
Hope this helps (you or somebody else).
Regards, Paul.
Go here to download firmware: http://www.samfirmware.com/firmwares.htm
rmanaudio said:
Go here to download firmware: http://www.samfirmware.com/firmwares.htm
Click to expand...
Click to collapse
Saw that.. but there's no I-Series... I can't see any firmwares for Samsung Galaxy S there - am I blind?
EDIT: Found it - thanks.
This JH2 on his site is the "updated" version of JH2 that fixes the 3-button recovery as per the Facebook page right?
http://www.facebook.com/note.php?note_id=10150262535205538&id=260085296049
or is this the "earlier" version of JH2?
http://www.multiupload.com/ZNBT2RY5Y0
Use 512 pit file.
http://samfirmware.webs.com/samsungandroid.htm
Top left, just had to click on "android phones" to get here... good luck!
slaman said:
Saw that.. but there's no I-Series... I can't see any firmwares for Samsung Galaxy S there - am I blind?
Click to expand...
Click to collapse
It is there...dont look for I series...click on Android. Then grey area for america files.
Got the file... tried to update through Odin... and it's stuck on the following for 15 minutes...
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> zImage
The phone still shows Download mode.
Do I need Odin v1.3 or is Odin v1.0 sufficient? Using PIT0512
EDIT: Pulled out battery... tried again... now see blue status bar moving along the bottom... fingers crossed that this works!
It completed... and same thing is happening. Can't start it up...
Purchased two Bell Canada Samsung Galaxy S as-is from local kijiji.
They all performing the same thing, rebooting at Galaxy S logo, GT-I9000M page, it won't go any further. and there is no recovery mode at start-up.
Here are the steps which I have played with for past two days.
1. Trying to get to recovery mode
- tried ADB, but it doesn't work, since "USB debug" is not on, and it won't accept as a device, and I am not able to turn that on, since I can't even get on the main screen.
- tried three key combo, vol up + home + power on, at least a hundred times for past two days, it doesn't work. fortunately download mode is working (at least I have more option to try). and I know how to get to recovery mode, I played with my friend's before.
2. Trying to use ODIN to flash the firmware
- unchecked "re-partition", unchecked "bootloader", pick 512 as PIT and then choose following as PDA
JH2, JK3, JK4, JL2
always successful on refresh, but phone still does the same, stuck at LOGO page
- also tried, checked "re-partition", and checked "bootloader", pick 512 as PIT and repacking following into PDA, Phone/Modem, CSC, still won't work...
JP series, JH, JK series, JL
At the beginning I though it was problem on CSC, I didn't use correct one to match my phone model #, but what's mine??? I can't go into my phone to check. I checked my friend's I9000, he used I9000BMCJK4, and I assume all JK series should work with me, since our IMEI are similar. And I tried many times on different cache.rft as CSC.tar, still no luck for me
I go crazy now, $400 USD gone. Seriously needing help. Any help is highly appreciated.
try the one jl2 download file and samsungfirmwares.com it flashes a special bootloader that may fix things.. it should be a single file you put in as pda nothing else..
if not they may have permantely trashed internal memory and you are sol.
lgkahn said:
try the one jl2 download file and samsungfirmwares.com it flashes a special bootloader that may fix things.. it should be a single file you put in as pda nothing else..
if not they may have permantely trashed internal memory and you are sol.
Click to expand...
Click to collapse
I have tried one of JL2 file from somewhere (don't remember where), but I will get one JL2 file from samsungfirmwares.com again, see if that works.
Do you mean, only choose the file for PDA, left PIT empty, and get everything uncheck?
permantely trashed internal memory? are these the common problem with this model? I got two of these, and both of them have the same issue, I think, there should be a way to slove it, right? Should I give up these thoughts???
anyways, thanks anyways, I will report back after I flesh JL2 from samsungfirmwares.com
Ok, you need to flash jl2 with pda, repartition, pit file and the secondary boot loader... The SBL(secondary boot loader) is what will actually fix your phone
Hopefully it will work.
Sent from my GT-I9000m using XDA App
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.rfs
<ID:0/005> Sbl.bin
<ID:0/005> zImage
<ID:0/005> factoryfs.rfs
<ID:0/005> modem.bin
<ID:0/005> param.lfs
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Still no luck on this firmware, I9000UGJL2, by the way, should be samfirmware.com instead of samsungfirmwares.com
above message I got from ODIN3 v1.30, it looks fine for refresh, but it doesn't work. the phone keep rebooting, it won't pass LOGO page, again, only download mode I can use.
HELP! HELP! HELP!
any leads???
is "<ID:0/005> Sbl.bin" secondary boot loader???
I got the file for PDA, I9000UGJL2, is this the one? if not, where should I get it? how do I update it?
I did it again, with "re-partition" checked, PIT choosed as s1_odin_20100512.pit, I9000UGJL2_homebinary_add_param.tar (which I just downloaded from samfirmware.com), it still doesn't work.
anything else I can try? maybe something simple I didn't do???
I too am a bell user I had the same problem a few weeks back. This is going to sound messed up, but i'm going to do my best to explain how I solved the problem.
DO NOT MULTI-TASK ON THE COMPUTER WHILE DOING THIS. CLOSE ALL OTHER APPLICATIONS.
-remove external sd and sim card
-go into download mode (hold vol down+power+home).
-turn on ODIN
-plug in usb (both computer and phone)
-check re-partition
-ONLY use the 512 pit file. DO NOT use a rom.
-start ODIN and it should only take a minute. this will wipe your device completely but still allow you to access download mode.
- remove usb close ODIN
- start up ODIN again and connect usb
- use 512 pit and JP1 or JP2 rom.
- After flashing, this SHOULD give you an error and send you straight into recovery mode. you're looking for a specific error code. you need the error to have "sl01" or "sl10" (whichever, i forgot which it was) at the end of the path. if the end of the path has "m(something)" then use a different rom till you get the "sl10".
these errors are internal sd errors which your phone is experiencing right now, but the phone is fixable from the "sl10" error.
continuing...
- once you get the "sl10" error, close ODIN, unplug USB, turn off phone.
- go back into download mode.
- boot up ODIN with 512 pit and ULG2 rom.
- plug in phone
- start flashing.
this can give you two outcomes:
1) fixed galaxy S
2) error code with "m(something)" at the end of the error path.
if it's #2 do this all over again until it works.
This took me 3 days to figure out these steps, 10 hours each day. although it doesnt seem to make sense, my phone is working right now and it is where I am writing all this from. My only explanation is that Bell gets ****ty product from samsung. it's almost impossible to flash custom roms on a bell galaxy i9000 because the internal SD seems to have trouble being mounted.
i hope this helps and i hope it doesnt take long for you to fix this problem.
btw, if it does get fixed data connection wont be available. to enable it go to your apn settings. create new named "Bell" with apn as "pda.bell.ca" and leave all other options blank. data should be restored after that.
Sent from my GT-I9000M using XDA Premium App
jt_kyle said:
I too am a bell user I had the same problem a few weeks back. This is going to sound messed up, but i'm going to do my best to explain how I solved the problem.
DO NOT MULTI-TASK ON THE COMPUTER WHILE DOING THIS. CLOSE ALL OTHER APPLICATIONS.
-remove external sd and sim card
-go into download mode (hold vol down+power+home).
-turn on ODIN
-plug in usb (both computer and phone)
-check re-partition
-ONLY use the 512 pit file. DO NOT use a rom.
-start ODIN and it should only take a minute. this will wipe your device completely but still allow you to access download mode.
- remove usb close ODIN
- start up ODIN again and connect usb
- use 512 pit and JP1 or JP2 rom.
- After flashing, this SHOULD give you an error and send you straight into recovery mode. you're looking for a specific error code. you need the error to have "sl01" or "sl10" (whichever, i forgot which it was) at the end of the path. if the end of the path has "m(something)" then use a different rom till you get the "sl10".
these errors are internal sd errors which your phone is experiencing right now, but the phone is fixable from the "sl10" error.
continuing...
- once you get the "sl10" error, close ODIN, unplug USB, turn off phone.
- go back into download mode.
- boot up ODIN with 512 pit and ULG2 rom.
- plug in phone
- start flashing.
this can give you two outcomes:
1) fixed galaxy S
2) error code with "m(something)" at the end of the error path.
if it's #2 do this all over again until it works.
This took me 3 days to figure out these steps, 10 hours each day. although it doesnt seem to make sense, my phone is working right now and it is where I am writing all this from. My only explanation is that Bell gets ****ty product from samsung. it's almost impossible to flash custom roms on a bell galaxy i9000 because the internal SD seems to have trouble being mounted.
i hope this helps and i hope it doesnt take long for you to fix this problem.
btw, if it does get fixed data connection wont be available. to enable it go to your apn settings. create new named "Bell" with apn as "pda.bell.ca" and leave all other options blank. data should be restored after that.
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
great!!! Another option I can try. Thank you.
I will try it out right after my work. so the idea behind this, is bricking it into recovery mode and S10 error code. and then fresh right back with correct ULG2 (is this correct? frist time heard about this rom)
anyways, I will post back with result.
Where can i find this ULG2 rom?
did it work?
Thananjeyen said:
Where can i find this ULG2 rom?
Click to expand...
Click to collapse
I think jt_kyle meant I9000UGJL2
and you can get them from samfirmware.com
Paallikko said:
did it work?
Click to expand...
Click to collapse
yes, lucky I got one of my Bell Samsung phone work. Since I done a million times of refreshing and rebooting and etc... I am not sure what I did, now I still trying to remember last 10 steps I did to make this work.
But definitely, I could not have done this repair without jt_kyle. Thank you so much, jt_kyle.
jt_kyle, Thank you!!!
but none of JP1 or JP2 is givining me the error "tl10", I tried
I9000DXJP1
I9000TGYZSJP2
I9000XXJP1
I9000XXJP2
it come out error started with "m..."
I just keep refreshing each on PDA 3 to 4 times, and choose with re-partition or without. At the end I try a few another ROMs as well, I still get no "tl10", but somehow, just that magicical moment, the screen come out a set of commands that look like format sd card, so I got excited, fresh it with JL2. It is back to work.
still no clue the steps of fixing the problem.
one done, the another one to go.
any more ideas please, and I think I am really close to solve this one now.
Thank you All
FIX
Look for a file called I9000UGJL2Complete follow the same steps pit and so on after your phone boots up youll have a blank baseband then you get the I9000UGJL2 modem and flash it where it says phone this has unbricked a few for me hope this helps
EVERED78 said:
Look for a file called I9000UGJL2Complete follow the same steps pit and so on after your phone boots up youll have a blank baseband then you get the I9000UGJL2 modem and flash it where it says phone this has unbricked a few for me hope this helps
Click to expand...
Click to collapse
if you have a way for me to give you this file i do have it just not sure how to do so because its 286MB
Could it be dead?
Since you have one of the infamous i9000m's it might also just be a dead SD card? You might try calling samsung and trying to get it repaired under warrenty as they are all under a year old (try and flash jl2 first even it will not boot up). It sounds like no receipt may not be an issue.
Lots of info from allgamer's list of i9000m issues in the general section.
At least you have one in the meantime!
same problem
Hey ive got pretty much the same problem that you had. Only differences are that I'm from Australia and am on Virgin network.
My phone became semi bricked one day when it restarted and since the 3 button combinations did not work i ordered in a USB jig which i received today. I used odin 1.8 to try and flash to I9000BVJJPD which i got from samfirmware.com but it ended up stuck on the logo screen vibrating once in a while. I decided to repeat it with no avail and began to use other roms and use .PIT.
This is where my phone became even worse and is now in it's current position; rebooting at the GT-I9000 page. I tried the method that jt_kyle suggested, substituting australian roms instead but it is still in the same position.
Does anyone have any other suggestions or should i just try getting a warranty?
Look for the ugjl2 complette and repeat what I said
Sent from my GT-I9000 using XDA Premium App
EVERED78 said:
if you have a way for me to give you this file i do have it just not sure how to do so because its 286MB
Click to expand...
Click to collapse
I think I have this I9000M_JL2_JL2_JL2_JL2_UG_BMC file, is the same file that you are talking about? JL2 Complete?
I tried this file many times, it won't work neither.
for past one hour I played around this phone, trying to repeat the steps I did for the first phone. Unfortunately, nothing is working for me AGAIN!
but I got these error page all the time, like following...
update media, please wait
E:Can't mount /dev/block/mmcblk0p1
(I/O error)
E:copy_dbdata_media:Can't mount SDCARD:
I think that's bigest problem in my case, and for a lot of people in this forum. Do any people has a good solution for this???
Hello All,
I tried flashing my phone (to I9000XXJVS)
I've only gotten to step 11, which flashes the phone.
In ODIN, I selected PIT, PDA, PHONE and CSC. All 4 had files.
I selected the following options:
Re-Partition, Auto Reboot and F. Reset Time
While flashing, I got the following messages
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> factoryfs.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> cache.rfs
<ID:0/005> zImage
<ID:0/005> modem.bin
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/005> Removed!!
I switched off the phone and tried to turn it back on.
It won't come one at all. It's not showing anything.
It won't even go into recovery mode.
It won't go into download mode.
Pls help.
Take the battery out for 15 minutes and then replace and see if it powers back on.
If it still wont turn on or go into download mode using the key combination then try using a USB JIG.
What rom did you try flashing?
I'm trying to go to Gingerbread 2.3.5 I9000XXJVS.
I waited 15 mins. Still nothing.
Even when I put in the cable through USB, nothing shows up. Normally it shows that it's charging.
See screenshot of my ODIN configuration while flashing:
Try and plug your phone into the PC and then try the 3 button combo with the cable attached.
No difference. Still won't come on.
I hope the board is not fried.
Very strange...
I cant view the image you posted at the moment to see if files were put in the right places because im on works ancient internet browser but from what you wrote in the OP the flash appears to have gone ok...
Might be worth getting a JIG and trying that. If that doesnt work maybe its time for the unbrickable mod.
REALLY stupid question but you have flashed the right firmware for your device right?
I would give the JIG a try. You can buy one from ebay for like less than £5 GBP or you can throw one together youself.
Did the phone reboot fully after the flash before you turned it back off?
Yes, the flash went OK.
What do you mean by the right firmware? I got the firmware from samfirmware. I actually new to this.
And what's a JIG? How do I put one together?
The phone didn't reboot. The screen was blank but kinda slightly lighted. So I tried powering it up but it didn't so I removed the battery.
I got the JIG. I'll try to build one myself.
I'll let you know if it works.
One more thing: the battery was kinda low when I started this operation.
I'm thinking maybe the battery ran out.
But it's not even charging when I plug it in.
What i mean is do you have an i9000 and not an i9000M or another variant of the i9000 and have tried to flash a firmware from an i9000 onto an i9000M or i9000B for example.
I wish i could see that picture you posted to have a better look.
In the PDA box you should have had a file called PDA or CODE... The modem box should have had MODEM or PHONE... and then CSC should have had CSC...
There should have been a PIT file in the PIT box...
You should have had repartion ticked... auto reboot ticked and auto F reset ( ithink its called that ) ticked.
The update bootloader and other check boxes that are below the 3 i mentioned should all have been unticked.
I use a GT-i9003
in PDA i have CODE...
in PHONE i have MODEM...
in CSC i have GT...
in PIT i have a .pit file
I had all three boxes ticked (Re-Partition, Auto Reboot, F. Reset Time)
All other checkboxes were unchecked.
It looks like you have flashed incompatible firmware onto your device.
You have flashed firmware for the i9000 which wont work on the i9003.
You have gone into the wrong section on Samfirmware.com. There is a seperate section for the i9003.
You can still try the JIG trick but im not sure if that will work either on your device as the hardware may be slightly different and require a different resistor value to force download mode but im not sure about that part...
It looks like you have flashed bootloaders onto your device that wasnt designed for it which could mean a hard brick.
Maybe the unbrickable mod will help you out.
Im not too sure how to help you from this point on im afraid if you cant get download mode working...
Have a good search through google and see if you can find any helpful information.
Other thing is to say you had an update for it and it broke your phone and try and play dumb and see what happens =/.
I hope you can get it sorted mate.
Hi I just decided to change my custom firmware to darkynote from rocketrom. It worked perfectly but I wanted to update my kernal also so afterwards i rebooted into recovery and installed version 2.6 of Abyss Note. Now My phone boots to the "Samsung Galaxy Note N7000" Screen and stays there unless i plug it in, then when i start it it goes to a frozen battery screen. I cant boot into recovery but i can boot into download mode. Can someone help me get my phone back to stock? I can't seem to find a tutorial anywhere that will work for me.
please help
edit: extra details, the Odin3 v1.85 process gets stopped at NAND Write Start!!
Here is the message feed:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKL7_N7000OXAKL7_N7000XXKL7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> factoryfs.img
<ID:0/006> NAND Write Start!!
Also tried using CF-Root kernal. no luck there. The Bar in Odin says KERNEL and the green bar is full, also stuck at NAND Write Start!!.
Someone respond, im gonna cry.
First Relax man, dont be in hurry, read this guide twice/thrice n calmly proceed...
It is nice still you can entre to download mode.
First get Stock firmware from here Type N700 in search field, it will show all available firmware, select you wish to flash n download
Note : If you select latest ROM KL7, you won't get Root + CWM, for that you have to Flash another ROM first, then You have to Root + CWM,then Install Mobile odin pro, now flash KL7 with Mobile Odin pro with 'ever root' option enable. If you selecting another ROM, ignore this note
Get odin n extract
Install:
Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly.
Extract tar file from the ROM you have download(password available at site from you have download). Put the phone into download mode (vol. down+home+power buttons),
Comlete close kies, if open. start odin, connect the phone via USB. Choose continue on the phone,
make sure that only two boxes are checked in odin - Auto Reboot and F.Reset Time.
Choose PDA button in Odin and select tar file you extracted before.
Choose START button.
The phone will reboot after the flash. Done.
Alright sounds good but i left it at the NAND write start thing overnight and when i came back it said this:
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Now I have a black screen and its flashing on and off with the frozen battery symbol. I think the battery is drained or something.
Also my download of the rom finished, there isnt any tar files its just a zip with an MD5 file and a Dll. Should i just but the MD5 file in the PDA section?
Edit: now my phone wont do anything when i try to put it in download mode.
Anyway if you are still able to entre Download mode, then try to flash stock kernel as i said above.
But thats what I mean, is it possible for the phone to not boot into download because the battery is dead or is my phone just bricked forever $850 dollars out the window.
tangelos said:
I cant boot into recovery but i can boot into download mode.
Click to expand...
Click to collapse
Actually i dont understand properly, your first post said U R getting into DW mode, if you can entre into boot mode, i guide you earlier, i cant say it bricked.
many time this happen after some error in procedure.
If you even not able to entre into Download mode, you need to entre it with JIG.
dr.ketan said:
Actually i dont understand properly, your first post said U R getting into DW mode, if you can entre into boot mode, i guide you earlier, i cant say it bricked.
many time this happen after some error in procedure.
If you even not able to entre into Download mode, you need to entre it with JIG.
Click to expand...
Click to collapse
Actually I was just updating you. At first it was working, then i tried a tutorial simmilar then the one you just gave me and it caused the phone to not turn on whatsoever. Can you link me to one of these "jigs". Thanks
You can get it readymade from market e.g. ebay or you can make it own home made
see here http://forum.xda-developers.com/showthread.php?t=819551
better first try with other battery once, if you cud manage
I was able to get a hold of one locally. When I plug it in, nothing happens. Any advice? Its for a GSII. Is that why? Or is it the battery thing. Before it stopped working completely, when i booted into download it would say low battery. Looks like its game over for my new phone .
I tried this with an old usb cable http://forum.xda-developers.com/showthread.php?p=20914895#post20914895.
Inserted the USB Jig afterwards. No luck
I suppose i have to take it to be J-tagged: http://toronto.kijiji.ca/c-buy-and-...-JTag-Service-Phone-Unlock-W0QQAdIdZ341742939
I'm sorry if this is not helping, or being so late, but I wanted to share my experience.
So, now can you enter the recovery menu by pressing the 3 buttons?
if you can then do a factory reset/wipe from the recovery and then flash an entire flashable ROM, maybe a stockROM or ROCKETROM.
you can upload ROCKETrom from the ordinary windows explorer , just copy and paste to the ex.SD.
the looping android animation actually happened to mine, and that's how I fixed it.
BTW: I didn't use Odin at all, or any other program.
Thanks for trying to help but this is completely irellavent. My phony CAN'T get into recovery and it NO LONGER CAN even get into Odin (download mode). I guess I wasn't clear when posting. Is anyone aware of a hardbrick fix or if sammy will repair ,my phone for a price.
Hi buddy. The EXACT same happened to be when trying to flash RocketV16. Frozen charge screen and everything.
To sort it I first let the phone start and hang on the black/white writing splash screen, removed the battery while it was on, held down the power button without the battery in for 3-5 seconds, put the battery back in. I then held Vol Down, the Home button and then the power down button (hold down power last) for some seconds until the Odin-Mode downloader came up.
After that I just followed a guide on flashing with Odin.
No more £9999999999 brick
unfortunatly i cant try that stratagy because i cant even get to the splash screen anymore. + i gave it to a local guy who claims to be able to jtag it. If it doesnt work ill send it to samsung and of course pay because i voided my warrenty. oh well. better then my old i9000m.
Galaxy Note N7000 Screen
I hate to hijack your thread but what I have to ask directly relates to your issue.
I have been searching for any file that contains this actual GALAXY Note Boot Screen - I am looking for this image file with the hope of making this my sole wallpaper/background. If there is anyway you or those who are reading this can PLEASE attach the file or at the very least provide a link so I 'd be able to download it for myself. I'd sincerely appreciate any help I can get.
I'm willing to pay ANY PERSON WHO PROVIDES A HIGH QUALITY IMAGE HOPEFULLY ALREADY SIZED FOR IMMEDIATE USE.
I'm sorry - please don't take this message as that of "shouting", My hope was to capture readers attention. Again, I apologize in advance for anyone having taken this message as shouting. That was not my intent.
Jim
connection
hey,i don't get how u manage to transfer stock firmware into the phone when pc cannot detect any file from the note???is it using odin??if yes,may someone share how to connect the phone to the pc via odin??
---------- Post added at 07:37 PM ---------- Previous post was at 07:27 PM ----------
hey how you manage to upload rocket rom,my pc cannot detect any file from my phone..even simple window explorer does not turn up..i hope u may help me...
me too Stuck at Galaxy Note Boot Logo
dr.ketan said:
First Relax man, dont be in hurry, read this guide twice/thrice n calmly proceed...
It is nice still you can entre to download mode.
First get Stock firmware from here Type N700 in search field, it will show all available firmware, select you wish to flash n download
Note : If you select latest ROM KL7, you won't get Root + CWM, for that you have to Flash another ROM first, then You have to Root + CWM,then Install Mobile odin pro, now flash KL7 with Mobile Odin pro with 'ever root' option enable. If you selecting another ROM, ignore this note
Get odin n extract
Install:
Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly.
Extract tar file from the ROM you have download(password available at site from you have download). Put the phone into download mode (vol. down+home+power buttons),
Comlete close kies, if open. start odin, connect the phone via USB. Choose continue on the phone,
make sure that only two boxes are checked in odin - Auto Reboot and F.Reset Time.
Choose PDA button in Odin and select tar file you extracted before.
Choose START button.
The phone will reboot after the flash. Done.
Click to expand...
Click to collapse
Dr Ketan,I have mentioned the same in your other thread about stucking at Galaxy Note Boot Logo forver.
I was on CheckRom v6 and then i went to flash a kernel and then got stuck at Galaxy Note Boot Logo.
I am not able to got to recovery mode by pressing power+home and vol+,but I can go to Download mode by pressing power+home and vol-.so i went to desktop Odin and tried flashing one of the rom(Dr Ketan Guide to Rooting).Seems like Odin was succesful but still stuck at Galaxy Note Boot Logo.
please need help here,I hope my Galaxy Note is not Bricked!
Try flashing a cf root kernel back
Sent from my GT-N7000 using XDA
Remkve battery for few min, thn put it back n try to enter recovery
If you able to enter recovery wipe cache n wipe data, thn reflash rom with pc odin.
Sent from my GT-N7000 using xda premium
3 things for I start 1 I'm bat in English because I'm dutch sorry for that if you don't understand a sentence just ask I will try to explain it 2 I'm also bad in making sentences that's why you don't see any dots Sorry for that to and the third thing is I'm not at bad at rooting or installing custom roms did it on my galaxy tab 3 no problems also on my cousins phone also no problems same as that from my mother.
I have for a long time my galaxy s1 like 3 years now I had it rooted and installed the Cyanogen mod (nightly form the 5th of April) and it was jut working fine I just update once in the moth or so always the lasts nightly but when I did updated for the newest nightly for that day (11th of may update) and when it restarted it was just stuck at the boot screen so I got the battery out waited 5 minutes and put it back in end reboot it did that like 3 times but every time it was stuck at the boot screen so I searched on Google but nothing works because Odin(3.0.7 also 3.0.9) fails to make connection or it was stuck at the nand write start
all what I tried was in the odin:
use an other cable
other pc / laptop
other usb ports (used always the back of the pc)
other packages for odin
other odin versions
I also tried using heimdall also no success
and after trying this all my phone even get worse when it was stuck i can only access download mode
recovery wasn't able any more so I also set the root package not on the pda from odin but on phone and when i booted the phone I get into an old recovery of cwm but he was not able to mount my storage or something else after just trying around with odin and a little heimdall no success now I can only access download mode and odin sees my phone but it doesn't matter where I put any package it just loads normal and when it needs to reboot it is just black screen it makes connection but it stops if I put the root package in the pda or a phone package in the phone sections then it stops at nand write start I tried to re-partition it with different pit files but also no success
*edit a friend said ty using odin 1.3.0 but now odin said this
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Set PIT file..
<ID:0/012> DO NOT TURN OFF TARGET!!
<ID:0/012> Can't open the specified file. (Line: 1455)
<OSM> All threads completed. (succeed 0 / failed 1)
if I do a root package in pda or phone
* edit
I fixed it just do this
http://forum.xda-developers.com/showthread.php?t=1583026
except for the voodoo kernel part its was stuck at boot screen hear only a women talking cant under stand it because my speaker in my phone is messed up
if you want to root it use this package http://download.chainfire.eu/132/CF...XA_JVU_2.3.6-v4.3-CWM3RFS.zip?retrieve_file=1
so maby you People can help me
Thanks for any help that comes