Related
I picked up a T-mobile Tab when I was in US and I want to use it in Europe with all European functions. Can I flash it to become equal to an European sold model?
Do I need to get the SIM unlock done first?
After I have done this, can I use KIES to do normal upgrades?
Thanks!
Bump
Still interested if anyone have flashed a US-Tab to Euro and then got it to work with Kies (doing upgrades etc).
I'm aware of the differences in modems support, but that is not an issue for me.
follow the steps
I have bought a T-Mobile tab a week ago and i have changed the Firmware with the European version to enable the dialer and then unlocked the phone with the hex edit by rotohammer first post.
So here is what you need to do
1) flash a euro firmware (get the latest from samfirmware.com)
and follow the instructions carefully.
2) unlock the device using the hack provided on the post here
How to carrier/SIM unlock the Galaxy Tab [Updated Dec 5 2010]
3) put any SIM you like and enjoy
Samsung SHG T849
I am a newbie. If I am in the wrong forum please redirect me.
My problem is that while flashing my t-mobile Samsung G tab using odin3 the power in my house went out and I am now bricked.
I get a logo that shows a graphic of a phone 2 dots and a yellow triangle with an exclamation mark in the middle, another 2 dots and a graphic of a PC.
When I try to get the download mode I cannot but I could get into a mode "Power reset or unknown upload mode" when I press both the 'up' and 'down' volume key at the same time as when I press the 'power on' key.
The logo would recycle every few seconds even if I try to power off.
I tried to let the battery run out and when I recharge the tab. the same thing repeats.
You need to re-flash using Odin!
Sent from my SGH-T849 using XDA App
Samsung SHG T849
I figured I would have to do that. Unfortunately my Sammy would not power down. It kept looping, off and on and when it was on, it gave me either the 'logo' or the 'power reset' message, both of which I described above. I even let the battery run down and upon recharge it immediately went into the loop I mentioned.
I tried to connect it to my PC but the PC would not recognize it at all. I checked to make sure I have the right drivers and I do.
I am hoping some one would know how to get the boot sequence working without having to physically open the pad.
skoogee said:
I have bought a T-Mobile tab a week ago and i have changed the Firmware with the European version to enable the dialer and then unlocked the phone with the hex edit by rotohammer first post.
So here is what you need to do
1) flash a euro firmware (get the latest from samfirmware.com)
and follow the instructions carefully.
2) unlock the device using the hack provided on the post here
How to carrier/SIM unlock the Galaxy Tab [Updated Dec 5 2010]
3) put any SIM you like and enjoy
Click to expand...
Click to collapse
Id skip step one and only flash known safe firmwares.
emohsain said:
I get a logo that shows a graphic of a phone 2 dots and a yellow triangle with an exclamation mark in the middle, another 2 dots and a graphic of a PC.
Click to expand...
Click to collapse
If you can get back to that screen, which is download mode, you can reflash Roto-JME and get back to a working Tab.
Samsung SHG T849
I had to wait awhile to reply because the tab went dead - no power. I tried to recharge it but it did not hold enough power to let me complete the task.
I am recharging it for 24 hours hoping that it will hold enough charge to let me complete the task.
In the meantime I located several sites for Odin3 v 1.7 but I was unable to get the same pack as ayman019 had which probably came from you rotohammer. will it be possible to get the link so I will have the right software/firmware?
(I located P1000XXJHA.rar files but I am having difficulties unzipping it. Each time I try it asks for a password. or would not even allow me to unzip it at all)
hi just curious,
can i flashed samsung tab t849 to samsung tab p1000??? it will not brick my tab???
pls confirm before i flash the tab, thanks
rotohammer said:
Id skip step one and only flash known safe firmwares.
Click to expand...
Click to collapse
sir can you help me w/ my samsung tab t849 to change in euro firmware??? i don't have the firmware for this phone, only i have is tha euro firmware for p1000. is it compatible w/ t849 tab and not come to brick???
skoogee said:
I have bought a T-Mobile tab a week ago and i have changed the Firmware with the European version to enable the dialer and then unlocked the phone with the hex edit by rotohammer first post.
So here is what you need to do
1) flash a euro firmware (get the latest from samfirmware.com)
and follow the instructions carefully.
2) unlock the device using the hack provided on the post here
How to carrier/SIM unlock the Galaxy Tab [Updated Dec 5 2010]
3) put any SIM you like and enjoy
Click to expand...
Click to collapse
Will this allow you to use voice +data in the US on AT&T (for example) without having to use a switcher?
need help
i recently bought samsung galaxy tab- t mobile. (SGH t849) made in korea. when i bought it it can call send massege. but i have updated stock firmware. i followed instructions but at the last moment it says failed. it was able to recover part of the firmware. but now i cant call but can send massage. can you help me please.... or suggest me a firmware that can make calls??
Roto-JME
rotohammer said:
If you can get back to that screen, which is download mode, you can reflash Roto-JME and get back to a working Tab.
Click to expand...
Click to collapse
Hi,
T849 from T-Mobile accidently flashed with wrong firmware and tab become totally dead. Repaired boot with Riff Box, so I can enter in to download mode now but couldn’t find Roto-JME or stock firmware. All download links are dead or deleted.
Would you share Roto-JME please?
Thank you in advance.
The link from rotohamer for tmobike stock is over. you have to update your tab to gingerbread 2.3
Sent from my GT-P1000 using XDA App
T849
I wiped Cache accidently, now my tab doesn't boot at all. can you provide me link to firmware that will support T849, its totally unlocked one so advice me the way not to get locked again.
Thanks in advance...
jokermuthu said:
I wiped Cache accidently, now my tab doesn't boot at all. can you provide me link to firmware that will support T849, its totally unlocked one so advice me the way not to get locked again.
Thanks in advance...
Click to expand...
Click to collapse
Horrible guide. Setup for failure and no support.
There is hardly any need for this old firmware. You can always run any European GB rom for P1000 as long as you keep T-Mobile modem you get 3g or use jpz modem and you get voice.
And with roto modem switcher you can even switch between voice and 3g.
The link in my signature is overcome links. It has gb jq1 rom and method to flash it.
Sent from my GT-P1000 using xda app-developers app
priyana said:
There is hardly any need for this old firmware. You can always run any European GB rom for P1000 as long as you keep T-Mobile modem you get 3g or use jpz modem and you get voice.
And with roto modem switcher you can even switch between voice and 3g.
The link in my signature is overcome links. It has gb jq1 rom and method to flash it.
Sent from my GT-P1000 using xda app-developers app
Click to expand...
Click to collapse
I have an SGH-T849. Trying to unlock it. Cant find any positive guides for custom roms or anything. Everything is only on the p1000 so I am taking my chances and flashing p1000 firmware so I can fit in.
You will be alright.
I am holding in my hand a T849 now running AOKP SGT milestone 6.
The T849 is exactly like a P1000 except the modem hardware.
I don't know about network unlocking though.
Sent from my GT-P1000 using xda app-developers app
Hey!
Soo I'm a total noob and i've looked around but can't seem to find this problem. I flashed a stock 2.3.3 for the samsung Galaxy S I9000M. My phone is originally from bell and I couldn't go on the market and sms that where sent to me shows that it was sent 4 hours ago. I bought it off some guy who unlocked it for me. I'm on the Fido network.
So I got a friend to flash it for me and it's on 2.3.3 I9000xxjvk. And now I can't get the 3G to work and it says i'm roaming. Mind you the market works now and sms shows the right time.
I know it has something to do with the modem. My friend suggested the SP6160_ARIES_DB221110 from :http://forum.xda-developers.com/showthread.php?t=876391
Now I have odin and the AIO Vibrant Toolbox installed. But i have no idea how to flash that modem. And I don't feel like bricking my phone thats barely a week old.
Please can someone tell me if this is the right modem and a step by step guide for a noob like me to install the modem.
p.s. I have the correct Fido APNs. it's the same one i used when i had it one 2.1
These links will help you out.
http://forum.xda-developers.com/showthread.php?t=1018414
http://forum.xda-developers.com/showthread.php?t=1015710
Basically you need a Bell Modem. JL2 or KCI will do.
Have you turned OFF Mobile Roaming in the settings .
jje
omgf Thanks soo much
http://forum.xda-developers.com/show....php?t=1018414
helped soo much
you guys are life savers.
well thats weird.... Now i can't search anything on the market, says it's not in the market.... But before I could. i can still download it if i find it on my pc through android market.
Now i can't even download from the pc site. and when i go on my phone it tells me
Warning: : your device might not be compatible with android market. Contact your device manufacturer for information.
This is frustrating. I flashed the JL2 modem, should i try the KCI?
shigoobee said:
Now i can't even download from the pc site. and when i go on my phone it tells me
Warning: : your device might not be compatible with android market. Contact your device manufacturer for information.
This is frustrating. I flashed the JL2 modem, should i try the KCI?
Click to expand...
Click to collapse
I'm not having any problems with the market, though in the past I did install eris market fix. Give it a shot.
I got a GNOTE from negri on 11/9. It seems it was s polish version. It has been working wonderfully on ATT (after adding in APN manually for 3g/H+ -- voice worked out of box).
I rebooted Today (11/13) and now it has the crossed out circle instead of bars and says "Insert sim" when I start to do cellular related activities.
I have Seated and reseated; nothing. pulled the sim and put back in my SGT (phone enabled) and it works. Put back in GNOTE, still no sim detected! Stuffed SIM in my N1; it works.
Any suggestions?
I had a similar SIM card issue when I tried to activate the 1700MHz band in Service mode (for fun). Wipes and stuff didn't solve anything. The way to revert it for me was flashing a full stock Samsung firmware in Odin.
Can you provide more details on how you did this?
Where does one get a full stock sammy note firmware?
Are there some good instructions on this?
I have flashed my SGT via odin several times. Same odin? Same process?
In the development section you will find some versions.
The key for me was flashing a new Modem (Radio/base band) image via Odin I think. I changed Kernels and ROM's but only flashing a ROM including the Modem got rid of my SIM issue. Not sure because in the end I flashed a full N7000OXAKJ1 firmware in Odin from here:
http://forum.xda-developers.com/showthread.php?t=1310513
It did the trick, though the tread is dead. I think any ROM including Modem might help, I currently running the 2.3.6 N7000ZSKK1 firmware and it is great, also included a Modem.
http://forum.xda-developers.com/showthread.php?t=1342797
fwelland said:
I got a GNOTE from negri on 11/9. It seems it was s polish version. It has been working wonderfully on ATT (after adding in APN manually for 3g/H+ -- voice worked out of box).
I rebooted Today (11/13) and now it has the crossed out circle instead of bars and says "Insert sim" when I start to do cellular related activities.
I have Seated and reseated; nothing. pulled the sim and put back in my SGT (phone enabled) and it works. Put back in GNOTE, still no sim detected! Stuffed SIM in my N1; it works.
Any suggestions?
Click to expand...
Click to collapse
when this happened to me, also due to turning on 1700, I was able to reset my phone by doing a factory reset. Unless your modem.bin is corrupted, you should not have flash a new rom.
- frank.
ugh....
you mean factory reset via Settings->Privacy->Factory Reset?
Tried that... No affect. Is there another way to do this?
Was hoping to fix w/o the flash. NOTE: I did go into that service menu with the 3G Freq are listed. I was curious when I saw the post. But I never changed anything. Just saw the screen and thought "neato". I wonder if there is another service screen that has an option for 'unfuck'???
Still searching for answers, before trying the ROM route...
fwelland said:
ugh....
you mean factory reset via Settings->Privacy->Factory Reset?
Tried that... No affect. Is there another way to do this?
Was hoping to fix w/o the flash. NOTE: I did go into that service menu with the 3G Freq are listed. I was curious when I saw the post. But I never changed anything. Just saw the screen and thought "neato". I wonder if there is another service screen that has an option for 'unfuck'???
Still searching for answers, before trying the ROM route...
Click to expand...
Click to collapse
Here is Chodthewacko posted about it:
http://forum.xda-developers.com/showthread.php?t=1335920
Factory reset and toggle band settings seems to have worked for him. I got frustrated and Odin flashed everything, that worked for me.
whoa....
when I try that procedure (* # * # 1 9 7 3 2 8 6 4 0 # * # * ) I get a pretty empty screen...can't do much of anything...just some useless buttons on the bottom of screen when I select the menu button...
I think I recall seeing another number for doing a similar thing...
fwelland said:
I got a GNOTE from negri on 11/9. It seems it was s polish version. It has been working wonderfully on ATT (after adding in APN manually for 3g/H+ -- voice worked out of box).
I rebooted Today (11/13) and now it has the crossed out circle instead of bars and says "Insert sim" when I start to do cellular related activities.
I have Seated and reseated; nothing. pulled the sim and put back in my SGT (phone enabled) and it works. Put back in GNOTE, still no sim detected! Stuffed SIM in my N1; it works.
Any suggestions?
Click to expand...
Click to collapse
OMG I have the EXACT same issue as you, and I got mine from NEGRI also! It was working perfectly until last night --- all of a sudden I got that circle and I've been trying to fix it since then! Please keep me posted if you find a solution, I was going to try and contact Negri tomorrow for an RMA.
still nothing.
I did a root. No changes...
I did a rom flash of kk1 ... no changes....
I was trying to reflash the modem with KJ6 modem....but have a signature failed problem...
now what???
I solved my issue by a combo of those steps.
I did full flash in Odin of jk1. When I rebooted that didn't solve things so I wanted to flash the other recommendation, kk the Chinese rom.
Upon entering recovery I noticed I lost 2e and was on 3e. So I had to download chainfire's rooted jk1 kernel and do that zerg rush to get root. It was while I was doing that that suddenly my similar got recognized. By the time it finished installing the rooter kernel I had full reception again. I flashed kk just for good measure and its been smooth since. Hope it works for you too and I'd love to know what the heck broke it in the first place??
Sent from my GT-N7000 using XDA App
hi fwelland, it's hk1981...so you tried the rom flash and it didn't work?
Hi hk1981,
No the KK1 rom flashed fine. By all accounts it works well, except that pesky phone part. This KK1 rom is really 'clean' and very little bloat-ware and it installs a vanilla boot animation (not a carrier one). All that is nice, but didn't help my problem
I did notice a peculiar thing: while in recovery (android recovery, not cwm) I get some warning about "CSC something or other, fixing".
I have a short list of things to try before I have exhausted my DIY options -- the post just above looks promising.
I think the answer is out there. We just need to keep looking and keep attention on this thread and others like it. This place and others like it are a huge help and I'd like to solve it and then give back a good set of instructions.
FWIW: I wonder if there was some voodoo in the polish rom that caused some issues in the modem when a different than expected sim was installed? Or if one of those funky polish apps that updated it self before I could turn off auto-updates has something to do with it (doubt this -- I don't think apps can do stuff unless rooted...)...
Still searching....I got this other pesky problem to deal with now: w-o-r-k
fwelland said:
Hi hk1981,
No the KK1 rom flashed fine. By all accounts it works well, except that pesky phone part. This KK1 rom is really 'clean' and very little bloat-ware and it installs a vanilla boot animation (not a carrier one). All that is nice, but didn't help my problem
I did notice a peculiar thing: while in recovery (android recovery, not cwm) I get some warning about "CSC something or other, fixing".
I have a short list of things to try before I have exhausted my DIY options -- the post just above looks promising.
I think the answer is out there. We just need to keep looking and keep attention on this thread and others like it. This place and others like it are a huge help and I'd like to solve it and then give back a good set of instructions.
FWIW: I wonder if there was some voodoo in the polish rom that caused some issues in the modem when a different than expected sim was installed? Or if one of those funky polish apps that updated it self before I could turn off auto-updates has something to do with it (doubt this -- I don't think apps can do stuff unless rooted...)...
Still searching....I got this other pesky problem to deal with now: w-o-r-k
Click to expand...
Click to collapse
I had that problem too, it doesn't detect that CSC and then goes ahead and applies something. Check to see if you are in 3e recovery, I think you are after having flashed vanilla JK1.
Re-flash Chainfire's rooted kernal for your appropriate version and then go back into recovery and it should be 3e and you can flash thru CWM then.
Also note; each time I flashed, I also wiped data/cache/davlik just to be sure.
yes it does say:
Code:
Android system recover (3e).
So I will need to try the methods you (crippenx) suggested.
FWIW, the CSC message that I get when I first enter recovery is:
Code:
# MANUAL MODE #
--Updating application...
Successfully update application.
--Appling Multi-CSC...
Installing Multi-CSC
Applied the CSC-code 'TGY'
Sucessfully applied multi-CSC.
I have no idea what this means. It does it every time I enter recovery.
FWIW, I never flashed this gnote with ODIN (I have used ODIN on my SGT several times). I got to KK1 by first rooting via http://forum.xda-developers.com/showthread.php?t=1329360 (using 'forget the above steps') and then using the CWM 'kk1-wipe.zip' from here http://forum.xda-developers.com/showthread.php?t=1342797 -- I didn't use ODIN to get to kk1.
I see on the Root/Unroot thread, there is a KK1 kernel option for 'simple'. I think I will try that with rooted already script.
But I am open to any/all suggestions...
Code:
Baseband
N7000XXKJ6
Kernel
2.6.35.7-N7000ZSKK1-CL706440
[email protected] #2
Build Number
GINGERBREAD.ZSKK1
fwelland said:
whoa....
when I try that procedure (* # * # 1 9 7 3 2 8 6 4 0 # * # * ) I get a pretty empty screen...can't do much of anything...just some useless buttons on the bottom of screen when I select the menu button...
I think I recall seeing another number for doing a similar thing...
Click to expand...
Click to collapse
My rough guess is that the phone has a list of 'valid service menu options', and it cross references it with what is on the SIM card.
Once the phone decides it's not going to read your sim card, the service menu is blank. This is a real headache.
That's why once I set the 1700+2100 combo, and my phone boycotted my sim, I wasn't able to set it back.
That's really dumb, imho, to have a one way toggle like that. I'm fine for settings to enable/disable other settings, but for a setting to disable itself? ugh.
I would really like to know what's going on. I was planning on switching to AT&T before my next trip (which is soon) but I can't risk my phone glitching out like that during the trip.
Actually, the ROM is on my SD card so I guess it wouldn't be THAT horrible, but it's certainly not something I want to do. Perhaps we just need a way to flash back the modem.bin, assuming it's corrupted.
- Frank
Sorry typo on my part. You are in 3e recovery because of that base flash, now you need 2e recovery which you can get via chainfire's rooted kernel. His installation procedure runs a batch file that uses that zerg rush exploit which I gather is partially from gingerbreak. It was during this procedure that my baseband suddenly came back, my sim card finally detected.
Once that was done, I entered 2e cwm with volume up,power,middle button and did erase of data,cache,davlik and then flashed kk rom via zip file.
Sent from my GT-N7000 using XDA App
fwelland said:
yes it does say:
Code:
Android system recover (3e).
So I will need to try the methods you (crippenx) suggested.
FWIW, the CSC message that I get when I first enter recovery is:
Code:
# MANUAL MODE #
--Updating application...
Successfully update application.
--Appling Multi-CSC...
Installing Multi-CSC
Applied the CSC-code 'TGY'
Sucessfully applied multi-CSC.
I have no idea what this means. It does it every time I enter recovery.
FWIW, I never flashed this gnote with ODIN (I have used ODIN on my SGT several times). I got to KK1 by first rooting via http://forum.xda-developers.com/showthread.php?t=1329360 (using 'forget the above steps') and then using the CWM 'kk1-wipe.zip' from here http://forum.xda-developers.com/showthread.php?t=1342797 -- I didn't use ODIN to get to kk1.
I see on the Root/Unroot thread, there is a KK1 kernel option for 'simple'. I think I will try that with rooted already script.
But I am open to any/all suggestions...
Code:
Baseband
N7000XXKJ6
Kernel
2.6.35.7-N7000ZSKK1-CL706440
[email protected] #2
Build Number
GINGERBREAD.ZSKK1
Click to expand...
Click to collapse
For me flashing all partitions via Odin worked (no pit file or repartition). Tried all sort of stuff from recovery first with no result.
I don't know what partition flash from Odin did the trick, but you could try Odin flashing a Modem separately and check if that works. If not try the rest?
Finally got back to this.
After much fusing I finally got KK1 and cwm working. It was odd, I had to re-run the whole root process again.
At that point I could apply the KJ6 modem w/o any problems (via cwm)
no dice!
Still dead!
Not sure where to go next???
Can some one provide a few details about flashing a modem,rom and/or kernel via ODIN? Perhaps that method will work....
fwelland said:
Finally got back to this.
After much fusing I finally got KK1 and cwm working. It was odd, I had to re-run the whole root process again.
At that point I could apply the KJ6 modem w/o any problems (via cwm)
no dice!
Still dead!
Not sure where to go next???
Can some one provide a few details about flashing a modem,rom and/or kernel via ODIN? Perhaps that method will work....
Click to expand...
Click to collapse
Oh when you flashed jk1 I assumed you did it the old way via Odin and the multiple files. That's how I did it and you're right, that may be what fixed it as when I used to brick my sgs and sgs2, it was always a full Odin flash of stock that brought it back from the dead
To flash in Odin put your phone in download mode. Fire up Odin. In csc point to csc file. In phone section point to modem and for PDA you point to the code file. Don't put anything for pit or bootloader and unchecked the repartition toggle.
Connect your phone and wait for Odin to detect it and show yellow in the status window. Press start and you're good to go. Hope this does it!
Sent from my GT-N7000 using XDA App
Hello,
I have searched multiple forums for hours today and have figured out what is going on with my HTC Vivid. (It has been upgraded to AT&T Official ICS.)
It was working fine up until yesterday where it was not receiving a signal from the mobile network and the signal icon has an X through it. The SIM card is properly inserted and another SIM card has been tried as well. Looking through other threads it seems like the Radio RIL files may be missing or corrupt. The IMEI number and *#06# code does not show an IMEI number either. The baseband version says unknown. I am not sure what happened as I have never loaded any other ROM on it.
I downloaded the Official RUU ICS upgrade ROM today and tried reflashing it, with no luck.
What is interesting (and the other person who had the radio problem) is that when I left the phone sit off overnight and then turned it on in the morning, the phone connected to the mobile network and I had a signal. When I restarted the phone, hours later, the phone lost connection to the mobile network and that is when I started digging and found the problem with the baseband version being unknown.
Is there anything anyone can suggest? Can I reflash the baseband files or copy them from someone somehow using ADB? It seems like there is where my problem lays. I've searched for ways on how to downgrade from ICS to the official GB stock rom, but it doesn't seem like it can be accomplished.
(I tried downloading the Holiday Cingular version of the GB stock rom but the update failed. I read about the ICS HBOOT version being different and not allowing it.)
Thank you in advance for helping and any suggestions.
Have you gotten a new sim card yet? That needs to be your first step. My captivate did the same thing and turned out the sim went bad
Sent from my HTC PH39100 using Tapatalk 2
Cor-master said:
Have you gotten a new sim card yet? That needs to be your first step. My captivate did the same thing and turned out the sim went bad
Sent from my HTC PH39100 using Tapatalk 2
Click to expand...
Click to collapse
Yes I have tried a different sim card. I don't believe thats the issue though being that it worked with the same sim after I let the phone sit overnight. From reading about others experience, it doesn't seem that the sim is the issue but more the baseband version and imei information missing.
centro7710 said:
Hello,
I have searched multiple forums for hours today and have figured out what is going on with my HTC Vivid. (It has been upgraded to AT&T Official ICS.)
It was working fine up until yesterday where it was not receiving a signal from the mobile network and the signal icon has an X through it. The SIM card is properly inserted and another SIM card has been tried as well. Looking through other threads it seems like the Radio RIL files may be missing or corrupt. The IMEI number and *#06# code does not show an IMEI number either. The baseband version says unknown. I am not sure what happened as I have never loaded any other ROM on it.
I downloaded the Official RUU ICS upgrade ROM today and tried reflashing it, with no luck.
What is interesting (and the other person who had the radio problem) is that when I left the phone sit off overnight and then turned it on in the morning, the phone connected to the mobile network and I had a signal. When I restarted the phone, hours later, the phone lost connection to the mobile network and that is when I started digging and found the problem with the baseband version being unknown.
Is there anything anyone can suggest? Can I reflash the baseband files or copy them from someone somehow using ADB? It seems like there is where my problem lays. I've searched for ways on how to downgrade from ICS to the official GB stock rom, but it doesn't seem like it can be accomplished.
(I tried downloading the Holiday Cingular version of the GB stock rom but the update failed. I read about the ICS HBOOT version being different and not allowing it.)
Thank you in advance for helping and any suggestions.
Click to expand...
Click to collapse
I had a similar problem and thought I solved it, but I later realised all my "solutions" didn't bring back the network but coincided with its reappearing cos no same "solution" worked more than once.
It's a very weird problem as the network shows up once in a while and when I'm using Mobile Network for Data, my phone hangs again and the IMEI, Network, baseband disappears on reboot...till further notice. I gave up trying and concluded it's either a bad modem (hardware) or something AT&T knows about!
You can get HBOOTS for both GB and ICS via Hasoons AIO kit
Flash the HBOOT, Flash the Image from Cingular GB RUU and I wish you luck!!!
ayulatins said:
I had a similar problem and thought I solved it, but I later realised all my "solutions" didn't bring back the network but coincided with its reappearing cos no same "solution" worked more than once.
It's a very weird problem as the network shows up once in a while and when I'm using Mobile Network for Data, my phone hangs again and the IMEI, Network, baseband disappears on reboot...till further notice. I gave up trying and concluded it's either a bad modem (hardware) or something AT&T knows about!
You can get HBOOTS for both GB and ICS via Hasoons AIO kit
Flash the HBOOT, Flash the Image from Cingular GB RUU and I wish you luck!!!
Click to expand...
Click to collapse
I found the download link, but the website says they're updating their drives, so who knows how much longer that will take.
Also, are you saying I should just use the tools within the kit to flash the HBOOT back to the previous version compatible with GB and then flash the RUU GB image after? Can I do that with the phone connected via USB or does it have to be flashed from the SD card? If it has to be flashed from the SD card, how do I go about doing that? If it can be done from the phone via USB, does the phone have to be in recovery mode?
I have tried reflashing the ICS RUU multiple times w/ version 3.26.502.52 and 3.26.502.56, both do not fix the issue. Do the baseband and or radio files NOT get flashed within these updates?
Thanks for the response!
centro7710 said:
I tried finding a download link for the AIO kit on the link provided, but I must be blind?
Also, are you saying I should just use the tools within the kit to flash the HBOOT back to the previous version compatible with GB and then flash the RUU GB image after? Can I do that with the phone connected via USB or does it have to be flashed from the SD card? If it has to be flashed from the SD card, how do I go about doing that? If it can be done from the phone via USB, does the phone have to be in recovery mode?
I have tried reflashing the ICS RUU multiple times w/ version 3.26.502.52 and 3.26.502.56, both do not fix the issue. Do the baseband and or radio files NOT get flashed within these updates?
Thanks for the response!
Click to expand...
Click to collapse
For any issues downloading Hasoon AIO tool, please use his thread (earlier provided).
Yes, use the AIO tool to flash GB HBOOT or read the SUPERGUIDE
and obtain rom.zip from the Cingular RUU
I don't know how to flash RUU via Recovery [email protected]@@!!!
I'd advice you follow my first solution here!!!
ayulatins said:
For any issues downloading Hasoon AIO tool, please use his thread (earlier provided).
Yes, use the AIO tool to flash GB HBOOT or read the SUPERGUIDE
and obtain rom.zip from the Cingular RUU
I don't know how to flash RUU via Recovery [email protected]@@!!!
I'd advice you follow my first solution here!!!
Click to expand...
Click to collapse
Thanks for the quick reply.
Your thread was the one I saw earlier with the simliar problem that I am having, only I have not loaded any custom ROMS. The phone just stopped receiving the signal the other day. I am still waiting for the download website to become available to use the tool to perform the flash of HBOOT, however, once I do that, will that erase the ICS rom from my phone? If so, what steps do I have to perform to get it in a "download mode" to accept the AT&T GB RUU? I'm a little confused on that part.
I read your first thread and I am a bit confused on exactly how you were able to correct the baseband/RIL issue (which I am assuming is the root of my issue). Do I have to extract some files from the RUU executable? Are the commands you provided to be used in ADB? I am confused as to what to do with [setprop ro.baseband 3.26.5XXX (<--- mainver: in android-info.txt in RUU.zip)] from your post. If that command is copying a file or just setting information (almost like as a registry setting within Windows) to point to the file or set a version number. Also if the XXX needs to have a certain number.
I thank you for your time and am trying my hardest to understand what to do to accomplish these steps.
centro7710 said:
Thanks for the quick reply.
Your thread was the one I saw earlier with the simliar problem that I am having, only I have not loaded any custom ROMS. The phone just stopped receiving the signal the other day. I am still waiting for the download website to become available to use the tool to perform the flash of HBOOT, however, once I do that, will that erase the ICS rom from my phone? If so, what steps do I have to perform to get it in a "download mode" to accept the AT&T GB RUU? I'm a little confused on that part.
I read your first thread and I am a bit confused on exactly how you were able to correct the baseband/RIL issue (which I am assuming is the root of my issue). Do I have to extract some files from the RUU executable? Are the commands you provided to be used in ADB? I am confused as to what to do with [setprop ro.baseband 3.26.5XXX (<--- mainver: in android-info.txt in RUU.zip)] from your post. If that command is copying a file or just setting information (almost like as a registry setting within Windows) to point to the file or set a version number. Also if the XXX needs to have a certain number.
I thank you for your time and am trying my hardest to understand what to do to accomplish these steps.
Click to expand...
Click to collapse
I did find the extracted files within the RUU executable and found the rom.zip which included the .img files among other files I assume needed as sources to flash the phone. I see a radio.img file would I be able to do anything with that?
Thank you.
centro7710 said:
I did find the extracted files within the RUU executable and found the rom.zip which included the .img files among other files I assume needed as sources to flash the phone. I see a radio.img file would I be able to do anything with that?
Thank you.
Click to expand...
Click to collapse
And I have a question, if the radio/baseband files are included in the RUU flash, what is happening as to why it is not being reflashed, or if it is being reflashed, why it is disabling the mobile network and providing an Unknown version to Baseband and clearing the IMEI number?
ayulatins said:
For any issues downloading Hasoon AIO tool, please use his thread (earlier provided).
Yes, use the AIO tool to flash GB HBOOT or read the SUPERGUIDE
and obtain rom.zip from the Cingular RUU
I don't know how to flash RUU via Recovery [email protected]@@!!!
I'd advice you follow my first solution here!!!
Click to expand...
Click to collapse
Here's where I am:
I successfully unlocked my bootloader, downgraded to GB, rooted. Tried to gain root access through adb terminal but it was not working properly.
I relocked my bootloader. Installed the ICS RUU AT&T ROM update. Unlocked my bootloader, rooted.
I see the commands you ran in your previous post. I am also receiving the same message of N/A when running the getprop ro.baseband
I tried the second command setprop ro.baseband 3.26.5XXX and then restarted the phone. I have tried it as posted, and also with swapping out the version that is located in my android-info.txt file: 3.26.502.56
Still no luck with setting the baseband version. IMEI still is cleared out.
Am I doing something wrong?
ayulatins said:
I had a similar problem and thought I solved it, but I later realised all my "solutions" didn't bring back the network but coincided with its reappearing cos no same "solution" worked more than once.
It's a very weird problem as the network shows up once in a while and when I'm using Mobile Network for Data, my phone hangs again and the IMEI, Network, baseband disappears on reboot...till further notice. I gave up trying and concluded it's either a bad modem (hardware) or something AT&T knows about!
Click to expand...
Click to collapse
Please see my initial quotes above...
All the previous steps I took were only a coincidence (not proven to work)!!!
We may need to contact AT&T to be sure its not a lock IMEI (and I'm wondering why it would be) or an experienced Dev
ayulatins said:
Please see my initial quotes above...
All the previous steps I took were only a coincidence (not proven to work)!!!
We may need to contact AT&T to be sure its not a lock IMEI (and I'm wondering why it would be) or an experienced Dev
Click to expand...
Click to collapse
Hey thanks for all of your suggestions. I contacted AT&T the day everything happened to see if it was on the block list. They said no. I tried multiple things including trying to re-flash the radio, but I was getting a signature failed error that I could not get around. I really think that's what the problem is. I gave up and ended up selling it.
centro7710 said:
Hey thanks for all of your suggestions. I contacted AT&T the day everything happened to see if it was on the block list. They said no. I tried multiple things including trying to re-flash the radio, but I was getting a signature failed error that I could not get around. I really think that's what the problem is. I gave up and ended up selling it, as is, on ebay instead to get a few bucks out of it and getting a new phone.
Click to expand...
Click to collapse
I really wouldn't mind selling mine too if I get a buyer. I'm just tired of all the troubles and no dev is willing to help.
ayulatins said:
I really wouldn't mind selling mine too if I get a buyer. I'm just tired of all the troubles and no dev is willing to help.
Click to expand...
Click to collapse
Exactly. It was my sister's phone. The sh*tty thing is we bought two off of ebay at the same time, 1 for me, 1 for her. Well, her phone was not in the box (either never shipped or stolen) so I had to file a claim through eBay which took 3 weeks to get the money back. Meanwhile, I gave her my phone (which is the phone in reference) to use instead. I bought her an iPhone instead now, along with purchasing one myself. I loved Android, but the bugs and fragmentation is getting too much for me to handle.
Dude, if you don't have an IMEI showing up, something is WAY wrong. That goes beyone the RIL not working... The RIL is probably fine. If your phone doesn't have an IMEI somehow, the cell towers are NOT, NO WAY, NEVER EVER going to register your phone on their network. You can put a billion SIM cards in there, or flash a billion stock ROMS, and if you don't have an IMEI, you will never be able to connect.
Something is probably corrupt or broken in your firmware or the hardware itself. I think your device is probably screwed.
My advice, is follow the steps to put your phone back to stock (including changing the bootloader message back to **LOCKED** and S-ON), and get it back to the phone company. They will be able to tell something is boned on the phone right away since it isn't displaying an IMEI.
Sorry to be the bearer of bad news and for your many wasted hours... But on the plus side, you now know a LOT about flashing and how your phone works now
Good luck with everything man! Hope they get you up and running soon!
I have the same problem as the OP but I have a IMEI showing up and a Basehand But won't connect to AT&T or anything they resent me a Signal & everything it shows a X with no bars it happened after I did a Factory Reset
anyone got the Radio.img?
inick73376 said:
I have the same problem as the OP but I have a IMEI showing up and a Basehand But won't connect to AT&T or anything they resent me a Signal & everything it shows a X with no bars it happened after I did a Factory Reset
Click to expand...
Click to collapse
That's weird..you try creating the apns again? I don't see how a factory reset would do that. Try toggling airplane mode too
Sent from my De-Sensed HTC Vivid using xda premium
I am currently having the same issues right now, it works if i leave the phone off for 1 hr it will work until i reboot then its down again, tried every thing possible, airplane mode will crash, reflashing the radios from gb and ics does nothing, setprop does nothing really. from this point it feels like a hardware issue.
sorry to revive an old thread, i just wanted to know if anyone came across this issue and had it fixed
i will get a log to see if there is errors showing up
Return it.
Sent from my HTC Holiday using Tapatalk 2
Hello
From what ive seen on here and other forums this is a very common problem with no real solution!?!
Am thinking that theres no fix but thought id ask before i give up so here goes!!
I have a samsung galaxy ace gt-s5830 which was originally on o2 uk that i wanted to use on vodafone uk
I managed to root the phone and get the unlock code from the phone via the bml5.img and the XVI32 Hex Editor
I then unrooted the phone put in the new sim and entered the unlock code
The phone now says vodafone uk on the lock screen but doesnt have any signal!?!
It still has an imei and baseband number and ive checked that the imei number isnt blocked
Ive also checked that all locks are off via samsung code *#7465625#
I have flashed the firmware to UK Gingerbread 2.3.6. using odin 4.38 and a one package tar.md5 file, wiped caches and rebooted etc
but the problem still remains!?!?!
Other than the no signal problem the phone works perfect and also when i take the sim card out theres signal?!?!
One other thing When ever i reboot the phone /system/csc/o2u/system cant be found although ive read this has nothing to do with the signal problem?!?
If anyone has any ideas or needs any further info then please let me know
I am new (probably pretty obviously!) to all this so please keep replys as simple as pos!!!
Many thanks
Matt
man10101 said:
Hello
From what ive seen on here and other forums this is a very common problem with no real solution!?!
Am thinking that theres no fix but thought id ask before i give up so here goes!!
I have a samsung galaxy ace gt-s5830 which was originally on o2 uk that i wanted to use on vodafone uk
I managed to root the phone and get the unlock code from the phone via the bml5.img and the XVI32 Hex Editor
I then unrooted the phone put in the new sim and entered the unlock code
The phone now says vodafone uk on the lock screen but doesnt have any signal!?!
It still has an imei and baseband number and ive checked that the imei number isnt blocked
Ive also checked that all locks are off via samsung code *#7465625#
I have flashed the firmware to UK Gingerbread 2.3.6. using odin 4.38 and a one package tar.md5 file, wiped caches and rebooted etc
but the problem still remains!?!?!
Other than the no signal problem the phone works perfect and also when i take the sim card out theres signal?!?!
One other thing When ever i reboot the phone /system/csc/o2u/system cant be found although ive read this has nothing to do with the signal problem?!?
If anyone has any ideas or needs any further info then please let me know
I am new (probably pretty obviously!) to all this so please keep replys as simple as pos!!!
Many thanks
Matt
Click to expand...
Click to collapse
hi matt first of all..
1. did you try another firmware?
2. you follow correctly the method to flash firmwares on odin?
seems to me that your download was corrupted, or you didn't flash properly on odin.
Its not a good thing to touch the bml5 partiton wich contains our imei ... even tough u unlocked it successfully you may have made some files corrupted wich can cause that ...
A major way to know this is ... does your previous sim aquire network?
And just to inform the error message is really not relevant ... csc function is to "inform kies" so it can do update your android version to the rom of your Country/Carrier.
Hello and thanks for both your replys
Firstly to answer matias.s
These are the instructions i followed to flash the fw
Flashing the Samsung Galaxy Ace GT-S5830 Firmware
1/. Enter Download mode by pressing and holding Volume down, select and power button simultaneously
2/. Connect phone to computer and open the Odin Multi Downloader v4.38 (it should show the com port it is connected on)
3/. For OPS, browse and select Cooper_v1.0
4/. For One Package, select the MD5 flash file attached and click start. (The attached firmware is for UK Gingerbread
2.3.6. You may use any firmware at this stage)
5/. Enter Diagnostic mode by pressing and holding select and power button simultaneously and clear caches
6/. Root the Samsung Galaxy Ace using the root.zip update
7/. Download, install and Open Root Explorer (File Manager) from Android Market
8/. Add Directory csc/system/XEU/system and move files over from CSC/system
9/. Enter Diagnostic mode again by pressing and holding select and power button simultaneously and clear caches
10/. Unroot the Samsung Galaxy Ace using the unroot.zip update
11/. Enter Diagnostic mode once again by pressing and holding select and power button simultaneously and clear caches
Odin came up with pass at the end
The only instruction i didnt follow exactly was 8
Firstly it wouldnt let me create the folder and then when i went into my directory there was already a /system/csc/XEU/system which had files
Could this be the problem?!?
And to answer snowpluralism
The sim im using works fine in other devices and as i said in the op the phone even has signal until a sim is inserted!?!
Update...
I flashed the fw again with a vodafone one package md5 via odin Odin passed the download and the phone is now branded with vodafone logo and apps
It is now on android version 2.3.5 build number gingerbread.buks but still has no signal
One strange thing when i first turned the phone on after the download it updated and downloaded vodafone apps and in the phone status said it was connected under mobile network state even though it still had no signal?!?
Thanks again for your replys and any ideas again please let me know!!
And thanks to snowpluralism for explaining about the csc error That explains why kies cant update my fw!!
When you check your imei is it correct?
Sent from my GT-I9300 using xda app-developers app
kofiaa said:
When you check your imei is it correct?
Sent from my GT-I9300 using xda app-developers app
Click to expand...
Click to collapse
Yeah the imei is correct and ive checked its not been blocked?!?