Related
I dont know what to do... Yesterday i flashed my wizard to wm6 mb rom, everything worked great but today, couple hours ago i tried to upload some stuff by activesync, suddenly pda disconnected and hanged, so softreset and nothing - its stuck on bootscreen where there is info about my components:
ipl 2.26
spl 2.26
gms 02.61.11
os 3.3.0.0 (was something like 10.xxx... but i flashed faria 3.5aku and now is 3.3)
i also tried to format but msg FormatFailed appear :/
it is possible to run in bootloader and charger also charge my wizard
what to do ????
Do you have a copy of the Wizard Love rom? If so, install that in bootloader mode. Remember to plug your USB cable into the phone.
drivex said:
I dont know what to do... Yesterday i flashed my wizard to wm6 mb rom, everything worked great but today, couple hours ago i tried to upload some stuff by activesync, suddenly pda disconnected and hanged, so softreset and nothing - its stuck on bootscreen where there is info about my components:
ipl 2.26
spl 2.26
gms 02.61.11
os 3.3.0.0 (was something like 10.xxx... but i flashed faria 3.5aku and now is 3.3)
i also tried to format but msg FormatFailed appear :/
it is possible to run in bootloader and charger also charge my wizard
what to do ????
Click to expand...
Click to collapse
i am after updating and still wizard hangs up on boot screen. versions has changed and bootscreen logo too, what now ? ;((((
drivex said:
i am after updating and still wizard hangs up on boot screen. versions has changed and bootscreen logo too, what now ? ;((((
Click to expand...
Click to collapse
I would suggest flashing back to a carrier aku2.x rom and ensure that your phone will come up properly on it. If it does then good, it's most likely not a serious hardware issue, if not then you might be out of luck.
looks like a brick to me..
So sorry m8.
I hope you can revive it !
Had similar problem with the Super rom.What worked for me was taking a back up on the memory card and reflashing from the card.Read the Wiki about details on how to go about it.
Try to flash the latest t-mobile ROM found on their site if all the suggested doesnt work..
@ DRIVEX
Try Hard resetting via the harware Buttons Softreset hole method. Here is how:
----------------------------------
While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key.
Hope it helps.
.
I've done. I used method with mtty and i copied os to sd card, after that i reflashed using minisd card and it works. Thx for everyting, u guyz do great job here hehe
Me too !
cyberdrakula said:
@ DRIVEX
Try Hard resetting via the harware Buttons Softreset hole method. Here is how:
----------------------------------
While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key.
Hope it helps.
.
Click to expand...
Click to collapse
I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...
Pls help me !!!
cachep2004 said:
I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...
Pls help me !!!
Click to expand...
Click to collapse
this is dead your flashrom chip in pda. repair only change semiductors or all board.
Pls show me another ways !
UfOuN said:
this is dead your flashrom chip in pda. repair only change semiductors or all board.
Click to expand...
Click to collapse
I'm living vietnam, so i'm trying to find out another ways, but i think they have no equipments.
Bless god for me.............pls
Revive Wizard
you must use youre camera button on the startup if you got error 260.
You see a lot of collors on youre display and then you can flash youre phone again.
Thanks alot !
sleurhut said:
you must use youre camera button on the startup if you got error 260.
You see a lot of collors on youre display and then you can flash youre phone again.
Click to expand...
Click to collapse
Thanks alot my friend, I will do it !
"FORMAT FAIL" again again pls ... help me !
( I've been trying many times, but when i did "While holding the Comm manager button and the Voice Command button, push in on the soft reset button (reset hole) once. Keep holding the Comm Manager and Voice Command buttons until there is a screen asking you if you want to clear all data. To commit, press the green send key " but screen appeared FORMAT FAIL. Pls help me...)
Pls ! Help me...."FORMAT FAIL" again again pls ... help me !
The hard reset doesnt work
I cant even get the screen to go on anymore. When I plug it in the light doesnt even go on to indicate that it is charging. SOmeone help me please.
ecomajor said:
I cant even get the screen to go on anymore. When I plug it in the light doesnt even go on to indicate that it is charging. SOmeone help me please.
Click to expand...
Click to collapse
Hard to help someone that hasn't told us anything.
From the sounds of it your battery has died. Until you get a good rom on there, the phone will NOT charge. You will need to find someone with a similar phone (or maybe go to your cell provider) and get them to charge the battery at this point. Once you have the battery charged then try following this step by step:
http://forum.xda-developers.com/showthread.php?t=298613
If that doesn't work, then come back and tell us more about what happened, what your IPL/SPL is, what type of phone you have, if its G3 or G4, etc... People here will help, but not without information.
mfrazzz said:
Hard to help someone that hasn't told us anything.
From the sounds of it your battery has died. Until you get a good rom on there, the phone will NOT charge. You will need to find someone with a similar phone (or maybe go to your cell provider) and get them to charge the battery at this point. Once you have the battery charged then try following this step by step:
http://forum.xda-developers.com/showthread.php?t=298613
If that doesn't work, then come back and tell us more about what happened, what your IPL/SPL is, what type of phone you have, if its G3 or G4, etc... People here will help, but not without information.
Click to expand...
Click to collapse
I have G3. i think its 2.25. I was trying to flash my rom when this all happened.
is there any way to charge it without a good rom?
ecomajor said:
I have G3. i think its 2.25. I was trying to flash my rom when this all happened.
is there any way to charge it without a good rom?
Click to expand...
Click to collapse
Not that I know of. Thats one of the reasons its recommended you start with a battery that has over 50% charge (personally I never flash with less than 100% in case something goes wrong). Not saying you didn't do that, but you appear to now be trying to work with a dead (or almost dead) battery, and that will only make things worse if you try to flash and then the battery dies in the middle (maybe not worse, but it sure won't help).
Like I said, you'll need to find someone with a similar phone or see if your local cell provider office will let you charge it (or swap it for a charged battery).
I got my ppc back up and I tried reflashing again and I have almost the same issue. It says format is successfull but then it gets stuck at the blue screen.
First of all i do not know where to post this. I have had a HTC wizard for over a year now. it has been working fine after cooking up wm6 and installing it for 6 months. today when i restartet the phone pulling the battery out and inserting it, the phone starts up, then the blue screen comes and shows ispl etc, then windows image shows, there it stops. i do not know what to do. It has been a while since i did pocket pc modding now, and i have forgotten all about it.
Alexander, [email protected]
Maybe something crashed the OS software.
Hope you have a system backup, or at least PIM backup using ActiveSync because what you need now is a hard reset.
Punching the reset hole (next to IR window) while holding CommManager+VoiceDial, then press "Dial" as prompted.
how do i hard reset my dash/s620?
i have tried hard reset
i have hard reset the phone. i do not have any backup in active sync. and i dont think that matters. because my phone does not connect to activesync since it does not start up. and in the three colored boot mode the phone is not detected by active sync. when i hard reset the phone it just came to the same point and freezed
If you didn't touch the ROM for long time, then it is probably a hardware failure...
lovemy318 said:
how do i hard reset my dash/s620?
Click to expand...
Click to collapse
READ YOUR PHONE MANUAL, and THIS IS NOT DASH FORUM.
hard to believe
First off, thanks for fast responses.
It cant be hardware(Not as a total theory of course) or likely not, because phone was not touched by water, shock, bumb fire or anything. it laid on my desk, worked, laid on my dask more, freezed. and it has been working for 6 months with wm6. is there anyway i can flash something into it. without activesync, but in the three colored boot mode?
Get into bootloader, plug in your usb cord and give it a minute...ON THE TRI-COLORED SCREEN do you see in the bottom corner "USB"??? If yes, you are OK. Get a stock rom such as the Tmo 2.26 and flash that. If you do not see "USB" in the bottom corner then as far as I know, you are fukd.
For more info on issues, read the linky in my siggy. There is valuable info there that may help with other ways to flash a rom.
Good luck.
i see usb
thanks, guess i am not fked then
Only problem is i have forgotten all about this now, and that i am sorry for.
But i have to ask you, as from norway wich stock rom to choose, what is stock rom, and when you say bootloader, is that an expression for the three colored screen or is that a program, that can flash in three colored screen? Thanks, i do not expect an answer on this noob questions, but i would really apreciate answers.
stock rom & bootloader
stock rom is the rom which comes with ur phone while purchasing it.. u can call it base rom..bootloader is tri-coloured screen which is bios for ppc if it gets fked then phone is bricked..next time if u cant boot up, then u can flash ur phone with the help of bootloader...
that was fast
thanks, but i do not think i have the rom that came with my mobile phone:/
and i do not know how to flash from tri colored screen, because all the files i have tried cant detect my phone.
ipl adn spl are 3.08 if that helps anything.
that was fast
is there an app you use to flash from tri colored
there is no need for any app, just connect ur phone to tri-coloured screen..u willl see usb in down left corner.. then ur phone is connected then run RUU utility.. if any problem comes i am online at hotmail... [email protected]
Can you power down? If not, remove battery for 1 seconds, the re-insert. Then press all at once the camera, comm and power buttons (or I believe you can also press the camera and soft reset. It is in the wiki explaining, as are some stock roms. Use any stock rom if you plan on flashing a cooked rom. The Tmo 2.26 is a decent stock rom, there is a 3.08 on the forum somewhere that you can also use. Get a stock rom. Get into the tri-colored bootloader. Look to see if it says usb in the bottom corner. If yes, connect your cable and using the ruu from the stock rom, flash your phone. Once a stock rom is installed follow the directions to cid/sim unlock your phone. Once unlocked, you can flash any cooked rom.
PS- I am assuming you have a G3 phone.
PPS- reading the wiki and the stickies are very helpful. Give them a try.
im sutch a noob
yeh i got same problem... i will try a hard reset but im at school... hope it fixes it... i got imate jasjam... BETTER WORK OR I WILL KILL MY BROTHER 4 STUFFING AROUND WITH MY PHONE
im sutch a noob
gah... it diddent work what do i do now????
yesterday i installed the rom of one of the above threads (win 6.5.28052) but everytime i boot up my device (when it is installed) it crashes.. constantly the same screen and i cant do anything?
i wanted to flash it to another win 6.5 rom. but i cant even turn on active sync on my phone
can anyone help me?
and fast. because i cant call and sms..
oh and: sorry for bad english
One post below is an exploit that seems to work without activesync, You could try this : http://forum.xda-developers.com/showpost.php?p=5336477&postcount=379
If I`m right it should connect again after You have a new SPL onboard. Relatively new here myself...
Another method would be to flash directly from an old SD card (not a new micro with adapter).
Edit : Maybe I misunderstood "turn on active sync on my phone" : Are You trying to flash when in bootloader mode (tricolor screen) ?
i was not flashing my phone in tricolor screen. but i did saw that screen when i installed the new rom?
but how do i come in the bootloader?
EDIT: can u please explain me in steps how i have to do this? (i am not so smart in those things..)
and how do u flash with a SD card?
another EDIT: i came a little bit further. no i see the commanager screen and disabled everything, then i tryed to turn on active sync. but then it freezes I WANT TO USE MY PHONE AGAIN!
Where did you find 28052 for trinity?.
Bootloader mode push on+camera botton+soft reset.
it was an older version.. typed it wrong. it was 28014..
but do u have a clue how i can fix this?
EDIT: now if i unlock my device. i get the windows screen when it boots up and does nothing.. so i cant do even less..
Ths to Supersport:
My recommendation for Flashing is:
Make sure you have Hard SPL on your Phone. I recommend Olipro 1.20 - Click Here for More Info
Be sure your battery is at least 50% full.
Start your phone in Tri Color Screen mode. Steps below
--Unplug your phone from USB
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
--Plug in the USB cable (if asked about installing a driver, do this), You should see USB in the White Box)
Now you can Flash.
And take a look also here:
http://forum.xda-developers.com/showthread.php?t=576880
Bye
atropo said:
Ths to Supersport:
My recommendation for Flashing is:
Make sure you have Hard SPL on your Phone. I recommend Olipro 1.20 - Click Here for More Info
Be sure your battery is at least 50% full.
Start your phone in Tri Color Screen mode. Steps below
--Unplug your phone from USB
--Hold down the Power & Camera Buttons
--While still holding them down, press the Reset Button using the Stylus
--Release the Reset Button, but continue to hold the Power/Camera buttons until you see the Tri Color Screen
--Plug in the USB cable (if asked about installing a driver, do this), You should see USB in the White Box)
Now you can Flash.
Click to expand...
Click to collapse
that tricolor screen says:
TRIN100
IPL-0.50
TRIN100
SPL-1.20.Olipro
so the spl version is good?
what to do next?
EDIT: what happens when i reset everything to factory standard?
ok. i did the steps u gave and i am flashing now..
now see what it does..
ow and btw.
how u can do dual boot on this phone? maybe i want android on it if it is possible
where can i find a good version of windows mobile 6.5? becuase the version i have now i dont like.. but the other version i tried was wrong?
Glad You found some help, I currently only have internet access at work...
What a good ROM is depends on Your liking. If You want a clean 6.5 base to install stuff Yourself and have lots of free RAM for bigger apps, check the second post of
http://forum.xda-developers.com/showthread.php?t=551424
The one my phone came with was also from xda-devs but couldn`t run iGO (nav software) because there was too little free RAM, too much preinstalled stuff running like Manila eyecandy...
So if You want a ROM with fancy today screens and other preinstalled stuff You`ll have to take a look around here, otherwise check the one above, many ppl recommend it.
Happy flashing
@flyby.
i dont like the standard skins of windows mobile 6.5 but i like the start menu and the file explorer thing,
and i used SPB Mobile before and i like that!
but what is the lightest version of windows mobile 6.5 here on xda? without that fancy touchflo etc, only the good start menu in the top and a good file explorer were u can scroll with u finger?
Hi guys!
I have been trying everything that I could find on XDA to fix my problem.
I got this HTC clone a few weeks ago, and it was working fine.
I decided to install a UI on it and it worked fine. After a while I got bored of the UI, so I decided to uninstall it. After the uninstall, the device indicated that it needed to be restarted. I did that, but after it rebooted, it started to reinstall Windows Mobile 6.1. I was annoyed by this, but was like, whatever, and let it continue.
Where the real problem started was when the device froze up (I left it alone for over an hour, but there was no change).
I then had to pull the battery. After I put the battery back into the T5355 it just keeps getting stuck on the "TOUCH Diamond2" screen.
I tried all the hard reset and soft reset tricks I could find and have no been able to either setting it back to factory or bootloader mode.
I was able to find a post that described how to place the boo.ini, flash.bin, and loader.bin file onto my micro sd card. I was able to to get the boot.ini an flash.bin files, but can't seem to find a loader.bin file (it that the actual OS rom?). I then found a post that showed how to use HiSilicon IDT to force the install of the OS Bin file (C02_HTC_20091102_R2127_英全视角B包.bin).
I followed the instructions on placing the T5355 into "Download" mode and pushing the OS bin fine to it.
I am able get the IDT software to detect the T5355 and start pushing the install, but the damned thing ends up giving an XLDR error.
PLEASE! PLEASE! Somebody help me! This phone is brand new and really want to get it working again.
Model: HTC(?) T5355
Please help me someone!!
Is there anyone out there that can help me???
I am so frustrated and can think of what else to do!
The biggest problem I have is that I can't use ActiveSync. If I could use that I wouldn't have much trouble.
Does anyone know how to use HiSilicon's IDT properly? The instructions I was working off of are in Russian. I think that a need a loader.bin file for the T5355 that I can put on my micro sd card...or maybe not...I don't know.
I just really want to get this device back to factory settings.
Please someone take pity on me!!!
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
I don't think you would be experiencing these problems with an original topaz
Please take care this is a HTC CLONE
Pisca said:
Please take care this is a HTC CLONE
Click to expand...
Click to collapse
oups, I'm high resolution on monitor, I thought it was saying "done" not "clone" ) ... there's a thread dedicated to china clones, look here http://forum.xda-developers.com/showthread.php?t=619643
run with a rom in bootloader, it shud work
enter bootloader [those orizontal strange colors]
try flashing a new rom. you may search and download the original 6.5 build from HTC
to enter bootloader, press "volume down + shutdown button" and then flash the rom
ATENTION: plug the USB cable, wait a few seconds, you should see USB on the lowest white color, then do the flashing job
Click to expand...
Click to collapse
DalvuS, thanks for the reply, but the issue is that I can't seem to get into bootloader mode . I wish I could. The T5355 seems to be stuck in the middle of wm 6.1 install. I need to somehow wipe the install and be able to push a reinstall back to the device.
I don't think you would be experiencing these problems with an original topaz
Click to expand...
Click to collapse
Exca that comment doesn't help me. It just makes me more sad. I was gipped when I bought the phone . I thought I paid for a "real" Diamond 2.
If you can't to catch the bootmode, looks like hardware problem.
You can't to repair it at home, imho. Try the specialized service.
..............
... and: are you sure about key combination for bootloader screen for CLONE?
Hello people, how can i dump my rom from my phone (mfu w71) for backup, because i cannot find any rom in english only in chinese. I started to dump the chinese rom with some chinese kitchen (K3系列ROM工具), but i'm stuck. I do not know to do anymore i have extracted ROM, SYS folder. I think it would be good to start another section on this forum for the chinese phones.
Some help from experienced cookers would me be much apreciated.
My T5355 is up and working!!!
Thanks to everyone who replied to my post!!!
I discovered that the problem was that the PC I was attempting the install from was running an AMD based processor.
I tried on the family laptop (which runs an Intel processor) and the install worked!
I AM SOOOO HAPPY!!!
b0gdi good luck with your issue. Try doing a search here in XDA for "dump my phone".
nothing[switched off] -> press start -> command -> bootloader -> bootloader commands -> system start -> play
checking one by one by interfering would have done the trick
I'm glad to hear that... so now you're ok
NEXT !
help me please
i Have Flash my phone 100 times with IDT for WM6.5 and WM6.1 all the versions my phone is T5355 Hot D2 but in one day i flash a rom that kill my phone the phone are conntinue to work but no screen picture only light i have try some russian Rom that kill my phone
the phone was been on guerant so i send him back to my supplier thay fix the phone but the factory said that thay need to change the screen so now thay really change the screen and the phone back to me with WM6.1 some New version 20.1.2010 some think like this i have made a call but the phone hang up and not make calls so i try to put him Back the WM6.5 English ROM that i use with this phone before i try to Flash Russian ROM that brake me the picture of the phone and block me the Bootloader Combination of SEnd+End+Power so that way i send him to repair .
so i try the English Rom that i have use before he DOwnload the Flash Fine but now the screen are stop to show picture But the Bootloader are work fine
so i try all the Roms that i have and all the same the screen dont want to show picture
some body have a same problem or can help me with this ?
hi guys i got a mda vario v t-mobile (htc tp2) dutch version i think because im from the dutch ehhehe. anyways im gettin trouble with install a other rom or updating this version...i know t-mobile rom sucks so i really wanna get this one off because the new roms rule the whole manila thingy clock thingy and stuff.. can anyone help me?
ye i forgot 2 tell that when i try 2 install the flash it gives me a error (260) its saying that i got connection problems but i think that might be wrong because i already tryed it out on a different pc... and i know i have 2 shut down my anti-virus programme
on my htc i get a warning(this package is not intended for your device type!! high chance of bricking!!! exiting now
I'm not sure what you're trying to flash, but check out the sticky threads. If you want a ROM other than that specifically designed for your device, your first step is HardSPL. Check out the sticky HardSPL thread, and if you have problems with it, then post in that thread.
well im trying 2 flash(hard-spl) my device HTC TOUCH PRO2(T-MOBILE VERSION VARIO V) i already downloaded the right rom for my device its the ENERGYROM FOR HTC PRO2. but when im trying 2 flash it with the hard-spl it says a error (260)(this package is not intended for your device type!! high chance of bricking!!! exiting now. and when im trying 2 install the ENERGY ROM for my device it stays on 0% of installing:S
tnx anyways
The fact that the ROM flash is staying at 0% is because you haven't got HardSPL. You need to get HardSPL on first.
I wonder if HardSPL can't handle the MDA Vario V ? What model number does it say it is, if you take out the battery, something like "RHODxxx" where the "xxx" is three digits, near where the serial number is ?
You really should post this in the HardSPL thread though.
ye thats why came with the hard-spl later on and even than it wont install the hard-spl. it says RHOD100
thank you for your support
1. Turn off your phone.
2. Connect USB with the PC (on the back on PC if not laptop)
3. Press Volume down + power button together on your phone (4 colored screen, red, blue, green and white should came up)
4. Connect usb to your phone. (should say usb in the middle of white part of the screen)
5. Start hard-spl.
6. When finished. remove the battery.
7. Put the battery back on
8. repeat 3 and 4
9. Start flashing "task 29".
10. repeat 6 and 7
11. repeat 3 and 4
12 start fleshing energy rom.
When you finish all adjusments turmno ff the phone, remove the battery for 5 minutes then start using your phone.
good luck
forster said:
1. Turn off your phone.
2. Connect USB with the PC (on the back on PC if not laptop)
3. Press Volume down + power button together on your phone (4 colored screen, red, blue, green and white should came up)
4. Connect usb to your phone. (should say usb in the middle of white part of the screen)
5. Start hard-spl.
6. When finished. remove the battery.
7. Put the battery back on
8. repeat 3 and 4
9. Start flashing "task 29".
10. repeat 6 and 7
11. repeat 3 and 4
12 start fleshing energy rom.
When you finish all adjusments turmno ff the phone, remove the battery for 5 minutes then start using your phone.
good luck
Click to expand...
Click to collapse
Erm, that's not going to work if HardSPL is bombing out with a "wrong device" error. But this discussion is going on in the HardSPL thread too.
May be you are not using the correct version of HardSPL? There are the CDMA and GSM versions. You should check which one your phone needs. Hope that helps
ye im using the correct hard-spl from the gsm thread.
ow ye
btw when i bootloader under the RHOD100 is writtin SPL-087.0000 that means theres already hard spl installed?
Please stop posting your questions in two places at once ? The HardSPL thread is the right place for your questions on HardSPL
please post your questions about hardspl in the appropriate thread, thread closed.