Related
Hallo,
sorry for my bad English. I have translate my Problem with promt . I have flash my Tab with JM6. After the flash my Tab do not boot. On the tab is a picture, a yellow triangle and a PC are indicated. Get with Odin 3 1.7 following error message.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Have you tried recovery
Sent from my GT-I9000 using XDA App
thank you for your answer.
no, what must i do?
wheel14 said:
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Click to expand...
Click to collapse
after you're flashing with Odin, then restating automatic in download mode, press the power button for 10 seconds (until tab will switch off), then restart by pressing the power button together with volume up. wait until finishing installing of CSC and then will restart by it self.
check my tread
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
wheel14 said:
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
Click to expand...
Click to collapse
I had the same situation, just take a look here. try to don't panic... try to follow my steps described in the tread and you might be succeed. I hope it help
I do not look though there sorry. I am in panic..which step....is the right?
i have flash the pit-file only. ist this right? and now?
wheel14 said:
I do not look though there sorry. I am in panic..which step....is the right?
Click to expand...
Click to collapse
try to look here and here
thank you.. I have flah the pit File only. now i will flash the pda without the pit. re-partition will be not selected. is this right. thank you for your help
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
wheel14 said:
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
Click to expand...
Click to collapse
I can't get you....can you describe a little what have you done? you're saying that you flash the firmware with Odin, right? and then? have you restarted in recovery mode? or you boot the phone loading the OS.....you should restart directly in recovery mode in order to finalize the installation of PDA and CSC....
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
wheel14 said:
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
Click to expand...
Click to collapse
Welcome back in our family.
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Go to samfirmware.com download the files for your device.
Select pit file then check repartition - flash
Select pda csc modem, uncheck repartition - flash.
Good luck! If you get any trouble send me a msg. on skype luc_de_mar
khatypically said:
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Click to expand...
Click to collapse
Sent from my GT-P1000 using XDA App
Thanks Lucian, This is exactly what I did in the first place. Used Odin 1.7 and applied the PIT file coming with it, then applied the P1000JPJM5 PDA and CSC modem file.
Unless the P1000JPJM5 is not for my device?? How to know?
Lucian, any clue?
My tab is dead after I tried to install an arabic firmware from samfirware.com. I bought my tab originally from the US. Now, I'll download the "suitable" firmware from samfirmware.com as you advised, but How would I ever know the suitable firmware given that my device is exactly this one (that's where I bought)(my devise is dead now and can only display the download mode):
www .amazon. com /GALAXY-TAB-P1000-16GB-UNLOCKED/ dp /B004AKOVIS/ ref=sr_1_1?ie=UTF8&s=electronics&qid=1305378100&sr=8-1
Regards,
Khatypically, alive with a zoombie tab
totally unresponsive tab
I have been searching around forums looking for advice and have been unable to locate a solution so here seems as good a place as any to ask for help. I have an unlocked gtp-1000 that has been running overcome 1.4.5 for last month very nicely until tonight when I thought it would be a good idea to get some gingerbread goodness like I have been using on my nexus one. was going to flash Overcome ROM v2.0.0 BETA 2 and was following guide but only got halfway through flashing stock gingerbread with odin when laptop unexpectedly did a restart for an unknown reason while I was away getting a snack. was unsure whether flashing process had been completed so opened odin again and tried reflashing. couldnt get past
setup connection...
so tried to reboot into download mode and then powered down. now tab is dead. battery was at 80% when it died
before I take back to samsung tomorrow any ideas?
I have plugged into wall charger= nothing
plugged into laptop=nothing and not detected
held power and volume up=nothing
held power and volume down=nothing
held power and volume up & home=nothing
no sounds or anything at all on screen
truly bricked?
Updates:
Hi Guys,
I applied the p1000nubjm2 firmware. I downloaded it from samfirmware. It's the latest P1000L firmware for America/Australia. It failed in the PDA file: P1000NUBJM2_P1000NUBJM2_P1000NUUBJM2_HOME.TAR . I was planning to apply the gingerbread update after that.
Now to the results, As you know, before, I was able to reach the download mode, the startup Galaxy Tab/Samsung screen, and the battery displays when connecting the cable. Now, after application of this lovely firmware and failure, nothing (literally "Nothing") takes place. The device became more dead than it was before . It doesn't display anything and it doesn't respond to power or displays the battery. It became a black $500 cost brick No matter how much time I keep it charging (or what "should be" charging), it would never startup again (sigh!) The ODIN and samsung kies no more recognize the device when connected to the computer.
Any additional clues before I decide to convert it to a teacup base?
Regards,
ARK
Purchased two Bell Canada Samsung Galaxy S as-is from local kijiji.
They all performing the same thing, rebooting at Galaxy S logo, GT-I9000M page, it won't go any further. and there is no recovery mode at start-up.
Here are the steps which I have played with for past two days.
1. Trying to get to recovery mode
- tried ADB, but it doesn't work, since "USB debug" is not on, and it won't accept as a device, and I am not able to turn that on, since I can't even get on the main screen.
- tried three key combo, vol up + home + power on, at least a hundred times for past two days, it doesn't work. fortunately download mode is working (at least I have more option to try). and I know how to get to recovery mode, I played with my friend's before.
2. Trying to use ODIN to flash the firmware
- unchecked "re-partition", unchecked "bootloader", pick 512 as PIT and then choose following as PDA
JH2, JK3, JK4, JL2
always successful on refresh, but phone still does the same, stuck at LOGO page
- also tried, checked "re-partition", and checked "bootloader", pick 512 as PIT and repacking following into PDA, Phone/Modem, CSC, still won't work...
JP series, JH, JK series, JL
At the beginning I though it was problem on CSC, I didn't use correct one to match my phone model #, but what's mine??? I can't go into my phone to check. I checked my friend's I9000, he used I9000BMCJK4, and I assume all JK series should work with me, since our IMEI are similar. And I tried many times on different cache.rft as CSC.tar, still no luck for me
I go crazy now, $400 USD gone. Seriously needing help. Any help is highly appreciated.
try the one jl2 download file and samsungfirmwares.com it flashes a special bootloader that may fix things.. it should be a single file you put in as pda nothing else..
if not they may have permantely trashed internal memory and you are sol.
lgkahn said:
try the one jl2 download file and samsungfirmwares.com it flashes a special bootloader that may fix things.. it should be a single file you put in as pda nothing else..
if not they may have permantely trashed internal memory and you are sol.
Click to expand...
Click to collapse
I have tried one of JL2 file from somewhere (don't remember where), but I will get one JL2 file from samsungfirmwares.com again, see if that works.
Do you mean, only choose the file for PDA, left PIT empty, and get everything uncheck?
permantely trashed internal memory? are these the common problem with this model? I got two of these, and both of them have the same issue, I think, there should be a way to slove it, right? Should I give up these thoughts???
anyways, thanks anyways, I will report back after I flesh JL2 from samsungfirmwares.com
Ok, you need to flash jl2 with pda, repartition, pit file and the secondary boot loader... The SBL(secondary boot loader) is what will actually fix your phone
Hopefully it will work.
Sent from my GT-I9000m using XDA App
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> cache.rfs
<ID:0/005> Sbl.bin
<ID:0/005> zImage
<ID:0/005> factoryfs.rfs
<ID:0/005> modem.bin
<ID:0/005> param.lfs
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Still no luck on this firmware, I9000UGJL2, by the way, should be samfirmware.com instead of samsungfirmwares.com
above message I got from ODIN3 v1.30, it looks fine for refresh, but it doesn't work. the phone keep rebooting, it won't pass LOGO page, again, only download mode I can use.
HELP! HELP! HELP!
any leads???
is "<ID:0/005> Sbl.bin" secondary boot loader???
I got the file for PDA, I9000UGJL2, is this the one? if not, where should I get it? how do I update it?
I did it again, with "re-partition" checked, PIT choosed as s1_odin_20100512.pit, I9000UGJL2_homebinary_add_param.tar (which I just downloaded from samfirmware.com), it still doesn't work.
anything else I can try? maybe something simple I didn't do???
I too am a bell user I had the same problem a few weeks back. This is going to sound messed up, but i'm going to do my best to explain how I solved the problem.
DO NOT MULTI-TASK ON THE COMPUTER WHILE DOING THIS. CLOSE ALL OTHER APPLICATIONS.
-remove external sd and sim card
-go into download mode (hold vol down+power+home).
-turn on ODIN
-plug in usb (both computer and phone)
-check re-partition
-ONLY use the 512 pit file. DO NOT use a rom.
-start ODIN and it should only take a minute. this will wipe your device completely but still allow you to access download mode.
- remove usb close ODIN
- start up ODIN again and connect usb
- use 512 pit and JP1 or JP2 rom.
- After flashing, this SHOULD give you an error and send you straight into recovery mode. you're looking for a specific error code. you need the error to have "sl01" or "sl10" (whichever, i forgot which it was) at the end of the path. if the end of the path has "m(something)" then use a different rom till you get the "sl10".
these errors are internal sd errors which your phone is experiencing right now, but the phone is fixable from the "sl10" error.
continuing...
- once you get the "sl10" error, close ODIN, unplug USB, turn off phone.
- go back into download mode.
- boot up ODIN with 512 pit and ULG2 rom.
- plug in phone
- start flashing.
this can give you two outcomes:
1) fixed galaxy S
2) error code with "m(something)" at the end of the error path.
if it's #2 do this all over again until it works.
This took me 3 days to figure out these steps, 10 hours each day. although it doesnt seem to make sense, my phone is working right now and it is where I am writing all this from. My only explanation is that Bell gets ****ty product from samsung. it's almost impossible to flash custom roms on a bell galaxy i9000 because the internal SD seems to have trouble being mounted.
i hope this helps and i hope it doesnt take long for you to fix this problem.
btw, if it does get fixed data connection wont be available. to enable it go to your apn settings. create new named "Bell" with apn as "pda.bell.ca" and leave all other options blank. data should be restored after that.
Sent from my GT-I9000M using XDA Premium App
jt_kyle said:
I too am a bell user I had the same problem a few weeks back. This is going to sound messed up, but i'm going to do my best to explain how I solved the problem.
DO NOT MULTI-TASK ON THE COMPUTER WHILE DOING THIS. CLOSE ALL OTHER APPLICATIONS.
-remove external sd and sim card
-go into download mode (hold vol down+power+home).
-turn on ODIN
-plug in usb (both computer and phone)
-check re-partition
-ONLY use the 512 pit file. DO NOT use a rom.
-start ODIN and it should only take a minute. this will wipe your device completely but still allow you to access download mode.
- remove usb close ODIN
- start up ODIN again and connect usb
- use 512 pit and JP1 or JP2 rom.
- After flashing, this SHOULD give you an error and send you straight into recovery mode. you're looking for a specific error code. you need the error to have "sl01" or "sl10" (whichever, i forgot which it was) at the end of the path. if the end of the path has "m(something)" then use a different rom till you get the "sl10".
these errors are internal sd errors which your phone is experiencing right now, but the phone is fixable from the "sl10" error.
continuing...
- once you get the "sl10" error, close ODIN, unplug USB, turn off phone.
- go back into download mode.
- boot up ODIN with 512 pit and ULG2 rom.
- plug in phone
- start flashing.
this can give you two outcomes:
1) fixed galaxy S
2) error code with "m(something)" at the end of the error path.
if it's #2 do this all over again until it works.
This took me 3 days to figure out these steps, 10 hours each day. although it doesnt seem to make sense, my phone is working right now and it is where I am writing all this from. My only explanation is that Bell gets ****ty product from samsung. it's almost impossible to flash custom roms on a bell galaxy i9000 because the internal SD seems to have trouble being mounted.
i hope this helps and i hope it doesnt take long for you to fix this problem.
btw, if it does get fixed data connection wont be available. to enable it go to your apn settings. create new named "Bell" with apn as "pda.bell.ca" and leave all other options blank. data should be restored after that.
Sent from my GT-I9000M using XDA Premium App
Click to expand...
Click to collapse
great!!! Another option I can try. Thank you.
I will try it out right after my work. so the idea behind this, is bricking it into recovery mode and S10 error code. and then fresh right back with correct ULG2 (is this correct? frist time heard about this rom)
anyways, I will post back with result.
Where can i find this ULG2 rom?
did it work?
Thananjeyen said:
Where can i find this ULG2 rom?
Click to expand...
Click to collapse
I think jt_kyle meant I9000UGJL2
and you can get them from samfirmware.com
Paallikko said:
did it work?
Click to expand...
Click to collapse
yes, lucky I got one of my Bell Samsung phone work. Since I done a million times of refreshing and rebooting and etc... I am not sure what I did, now I still trying to remember last 10 steps I did to make this work.
But definitely, I could not have done this repair without jt_kyle. Thank you so much, jt_kyle.
jt_kyle, Thank you!!!
but none of JP1 or JP2 is givining me the error "tl10", I tried
I9000DXJP1
I9000TGYZSJP2
I9000XXJP1
I9000XXJP2
it come out error started with "m..."
I just keep refreshing each on PDA 3 to 4 times, and choose with re-partition or without. At the end I try a few another ROMs as well, I still get no "tl10", but somehow, just that magicical moment, the screen come out a set of commands that look like format sd card, so I got excited, fresh it with JL2. It is back to work.
still no clue the steps of fixing the problem.
one done, the another one to go.
any more ideas please, and I think I am really close to solve this one now.
Thank you All
FIX
Look for a file called I9000UGJL2Complete follow the same steps pit and so on after your phone boots up youll have a blank baseband then you get the I9000UGJL2 modem and flash it where it says phone this has unbricked a few for me hope this helps
EVERED78 said:
Look for a file called I9000UGJL2Complete follow the same steps pit and so on after your phone boots up youll have a blank baseband then you get the I9000UGJL2 modem and flash it where it says phone this has unbricked a few for me hope this helps
Click to expand...
Click to collapse
if you have a way for me to give you this file i do have it just not sure how to do so because its 286MB
Could it be dead?
Since you have one of the infamous i9000m's it might also just be a dead SD card? You might try calling samsung and trying to get it repaired under warrenty as they are all under a year old (try and flash jl2 first even it will not boot up). It sounds like no receipt may not be an issue.
Lots of info from allgamer's list of i9000m issues in the general section.
At least you have one in the meantime!
same problem
Hey ive got pretty much the same problem that you had. Only differences are that I'm from Australia and am on Virgin network.
My phone became semi bricked one day when it restarted and since the 3 button combinations did not work i ordered in a USB jig which i received today. I used odin 1.8 to try and flash to I9000BVJJPD which i got from samfirmware.com but it ended up stuck on the logo screen vibrating once in a while. I decided to repeat it with no avail and began to use other roms and use .PIT.
This is where my phone became even worse and is now in it's current position; rebooting at the GT-I9000 page. I tried the method that jt_kyle suggested, substituting australian roms instead but it is still in the same position.
Does anyone have any other suggestions or should i just try getting a warranty?
Look for the ugjl2 complette and repeat what I said
Sent from my GT-I9000 using XDA Premium App
EVERED78 said:
if you have a way for me to give you this file i do have it just not sure how to do so because its 286MB
Click to expand...
Click to collapse
I think I have this I9000M_JL2_JL2_JL2_JL2_UG_BMC file, is the same file that you are talking about? JL2 Complete?
I tried this file many times, it won't work neither.
for past one hour I played around this phone, trying to repeat the steps I did for the first phone. Unfortunately, nothing is working for me AGAIN!
but I got these error page all the time, like following...
update media, please wait
E:Can't mount /dev/block/mmcblk0p1
(I/O error)
E:copy_dbdata_media:Can't mount SDCARD:
I think that's bigest problem in my case, and for a lot of people in this forum. Do any people has a good solution for this???
New member and somewhat stupid for trying to do this:
Long story short I attempted to throw gingerbread 2.3.X on the phone and now its stuck in either download mode, recovery mode, or if i just turn it on it comes up and says "GALAXY S GT-I9000 Samsung" The last thing that was successful was putting the SpeedMod Kernel on it.
In recovery mode it says "ClockworkMod Recovery v2.5.1.0 SpeedMod ULFK" on top and bottom.
The phone started out with factory settings.
When i try and use the ODIN 3 and try to do the Mast Clear it says :
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> Master Clear Started.....
and then stays like that indefinately...
Same thing with hitting "start"
Please let me know how to fix this, I know there are some really brilliant individuals on this forum and it would be greatly appreciated.
search for odin, download it, follow the steps and flash back to stock. you'll be fine especially since you can get into download mode.
edit: gah you already have odin. do you have one click or the one where u have to put the pit and tar files?
the same advice applies though, find the stock files, and go into download mode, then plug it in and flash back to stock.
i think master clear only works when the phone is on and you have usb debugging enabled.
Ive got ODIN 1.7 and ODIN3. I can get them to both recognize the phone but when I try and hit "start" with v1.7 it ust sits there forever. and Im not able to get ODIN3 to do anything either.
Any way you could provide a more step by step solution?
If you're having problems with ODIN, something that seemed to work for me was to remove my SIM card.
Try removing it and see if you have any luck.
I dont have anything in the phone, no sim and no external.
Just left it alone for a bit and came back and turned the comp back on and everything worked for ODIN. Thanks for the help fellas
Hi I just decided to change my custom firmware to darkynote from rocketrom. It worked perfectly but I wanted to update my kernal also so afterwards i rebooted into recovery and installed version 2.6 of Abyss Note. Now My phone boots to the "Samsung Galaxy Note N7000" Screen and stays there unless i plug it in, then when i start it it goes to a frozen battery screen. I cant boot into recovery but i can boot into download mode. Can someone help me get my phone back to stock? I can't seem to find a tutorial anywhere that will work for me.
please help
edit: extra details, the Odin3 v1.85 process gets stopped at NAND Write Start!!
Here is the message feed:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXKL7_N7000OXAKL7_N7000XXKL7_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> factoryfs.img
<ID:0/006> NAND Write Start!!
Also tried using CF-Root kernal. no luck there. The Bar in Odin says KERNEL and the green bar is full, also stuck at NAND Write Start!!.
Someone respond, im gonna cry.
First Relax man, dont be in hurry, read this guide twice/thrice n calmly proceed...
It is nice still you can entre to download mode.
First get Stock firmware from here Type N700 in search field, it will show all available firmware, select you wish to flash n download
Note : If you select latest ROM KL7, you won't get Root + CWM, for that you have to Flash another ROM first, then You have to Root + CWM,then Install Mobile odin pro, now flash KL7 with Mobile Odin pro with 'ever root' option enable. If you selecting another ROM, ignore this note
Get odin n extract
Install:
Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly.
Extract tar file from the ROM you have download(password available at site from you have download). Put the phone into download mode (vol. down+home+power buttons),
Comlete close kies, if open. start odin, connect the phone via USB. Choose continue on the phone,
make sure that only two boxes are checked in odin - Auto Reboot and F.Reset Time.
Choose PDA button in Odin and select tar file you extracted before.
Choose START button.
The phone will reboot after the flash. Done.
Alright sounds good but i left it at the NAND write start thing overnight and when i came back it said this:
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/006> Removed!!
Now I have a black screen and its flashing on and off with the frozen battery symbol. I think the battery is drained or something.
Also my download of the rom finished, there isnt any tar files its just a zip with an MD5 file and a Dll. Should i just but the MD5 file in the PDA section?
Edit: now my phone wont do anything when i try to put it in download mode.
Anyway if you are still able to entre Download mode, then try to flash stock kernel as i said above.
But thats what I mean, is it possible for the phone to not boot into download because the battery is dead or is my phone just bricked forever $850 dollars out the window.
tangelos said:
I cant boot into recovery but i can boot into download mode.
Click to expand...
Click to collapse
Actually i dont understand properly, your first post said U R getting into DW mode, if you can entre into boot mode, i guide you earlier, i cant say it bricked.
many time this happen after some error in procedure.
If you even not able to entre into Download mode, you need to entre it with JIG.
dr.ketan said:
Actually i dont understand properly, your first post said U R getting into DW mode, if you can entre into boot mode, i guide you earlier, i cant say it bricked.
many time this happen after some error in procedure.
If you even not able to entre into Download mode, you need to entre it with JIG.
Click to expand...
Click to collapse
Actually I was just updating you. At first it was working, then i tried a tutorial simmilar then the one you just gave me and it caused the phone to not turn on whatsoever. Can you link me to one of these "jigs". Thanks
You can get it readymade from market e.g. ebay or you can make it own home made
see here http://forum.xda-developers.com/showthread.php?t=819551
better first try with other battery once, if you cud manage
I was able to get a hold of one locally. When I plug it in, nothing happens. Any advice? Its for a GSII. Is that why? Or is it the battery thing. Before it stopped working completely, when i booted into download it would say low battery. Looks like its game over for my new phone .
I tried this with an old usb cable http://forum.xda-developers.com/showthread.php?p=20914895#post20914895.
Inserted the USB Jig afterwards. No luck
I suppose i have to take it to be J-tagged: http://toronto.kijiji.ca/c-buy-and-...-JTag-Service-Phone-Unlock-W0QQAdIdZ341742939
I'm sorry if this is not helping, or being so late, but I wanted to share my experience.
So, now can you enter the recovery menu by pressing the 3 buttons?
if you can then do a factory reset/wipe from the recovery and then flash an entire flashable ROM, maybe a stockROM or ROCKETROM.
you can upload ROCKETrom from the ordinary windows explorer , just copy and paste to the ex.SD.
the looping android animation actually happened to mine, and that's how I fixed it.
BTW: I didn't use Odin at all, or any other program.
Thanks for trying to help but this is completely irellavent. My phony CAN'T get into recovery and it NO LONGER CAN even get into Odin (download mode). I guess I wasn't clear when posting. Is anyone aware of a hardbrick fix or if sammy will repair ,my phone for a price.
Hi buddy. The EXACT same happened to be when trying to flash RocketV16. Frozen charge screen and everything.
To sort it I first let the phone start and hang on the black/white writing splash screen, removed the battery while it was on, held down the power button without the battery in for 3-5 seconds, put the battery back in. I then held Vol Down, the Home button and then the power down button (hold down power last) for some seconds until the Odin-Mode downloader came up.
After that I just followed a guide on flashing with Odin.
No more £9999999999 brick
unfortunatly i cant try that stratagy because i cant even get to the splash screen anymore. + i gave it to a local guy who claims to be able to jtag it. If it doesnt work ill send it to samsung and of course pay because i voided my warrenty. oh well. better then my old i9000m.
Galaxy Note N7000 Screen
I hate to hijack your thread but what I have to ask directly relates to your issue.
I have been searching for any file that contains this actual GALAXY Note Boot Screen - I am looking for this image file with the hope of making this my sole wallpaper/background. If there is anyway you or those who are reading this can PLEASE attach the file or at the very least provide a link so I 'd be able to download it for myself. I'd sincerely appreciate any help I can get.
I'm willing to pay ANY PERSON WHO PROVIDES A HIGH QUALITY IMAGE HOPEFULLY ALREADY SIZED FOR IMMEDIATE USE.
I'm sorry - please don't take this message as that of "shouting", My hope was to capture readers attention. Again, I apologize in advance for anyone having taken this message as shouting. That was not my intent.
Jim
connection
hey,i don't get how u manage to transfer stock firmware into the phone when pc cannot detect any file from the note???is it using odin??if yes,may someone share how to connect the phone to the pc via odin??
---------- Post added at 07:37 PM ---------- Previous post was at 07:27 PM ----------
hey how you manage to upload rocket rom,my pc cannot detect any file from my phone..even simple window explorer does not turn up..i hope u may help me...
me too Stuck at Galaxy Note Boot Logo
dr.ketan said:
First Relax man, dont be in hurry, read this guide twice/thrice n calmly proceed...
It is nice still you can entre to download mode.
First get Stock firmware from here Type N700 in search field, it will show all available firmware, select you wish to flash n download
Note : If you select latest ROM KL7, you won't get Root + CWM, for that you have to Flash another ROM first, then You have to Root + CWM,then Install Mobile odin pro, now flash KL7 with Mobile Odin pro with 'ever root' option enable. If you selecting another ROM, ignore this note
Get odin n extract
Install:
Install Kies on your computer, connect your phone and make sure that all the drivers installed correctly.
Extract tar file from the ROM you have download(password available at site from you have download). Put the phone into download mode (vol. down+home+power buttons),
Comlete close kies, if open. start odin, connect the phone via USB. Choose continue on the phone,
make sure that only two boxes are checked in odin - Auto Reboot and F.Reset Time.
Choose PDA button in Odin and select tar file you extracted before.
Choose START button.
The phone will reboot after the flash. Done.
Click to expand...
Click to collapse
Dr Ketan,I have mentioned the same in your other thread about stucking at Galaxy Note Boot Logo forver.
I was on CheckRom v6 and then i went to flash a kernel and then got stuck at Galaxy Note Boot Logo.
I am not able to got to recovery mode by pressing power+home and vol+,but I can go to Download mode by pressing power+home and vol-.so i went to desktop Odin and tried flashing one of the rom(Dr Ketan Guide to Rooting).Seems like Odin was succesful but still stuck at Galaxy Note Boot Logo.
please need help here,I hope my Galaxy Note is not Bricked!
Try flashing a cf root kernel back
Sent from my GT-N7000 using XDA
Remkve battery for few min, thn put it back n try to enter recovery
If you able to enter recovery wipe cache n wipe data, thn reflash rom with pc odin.
Sent from my GT-N7000 using xda premium
I dont have CWM installed. I can join only in Download Mode,
I am trying to install via PDA file with ODIN 1.85 it said:
ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013>
<ID:0/013> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-------------------------------------
When I try with Odin 4.43 it stocked at
<1> setup connection...
I have changed USB port on PC, nothing yet.
Did You installed Kies?
On what system are You trying to flash the phone?
On XP ODIN is not working, I flashed my i9001 with CWM on Windows 7 with ODIN and installed Kies without any problems.
aXiDroid said:
Did You installed Kies?
On what system are You trying to flash the phone?
On XP ODIN is not working, I flashed my i9001 with CWM on Windows 7 with ODIN and installed Kies without any problems.
Click to expand...
Click to collapse
Hello,
- I think thats my problem. I will try via Windows7 when I am ready too. I will reply.
Thank you.
No problem, just don't rush.
Flashing CWM takes a minute, after that the phone will reboot.
To enter to Recovery mode press Volume Up + Power and keep it pressed for 2 seconds after Samsung logo will appear.
BTW: If you encounter boot loop don't panic, just clear cache, data and dalvik and everything will be ok. I fixed boot loop on my phone by doing so.
edit: could you please press the THANKS button if I helped?
Are you using a pit file if so one correct for your device
Sent via that ninja standing right behind you
sider pyrgeds
Latrop said:
Are you using a pit file if so one correct for your device
Sent via that ninja standing right behind you
Click to expand...
Click to collapse
Hi,
- Yes I am using PIT file also but it stock at 'setup connection' with odin 4.43
- With odin 1.85 it said fail by this logs as below:
<ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013>
<ID:0/013> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed
Make sure you run Odin as admin and also try uninstalling device through device manager whilst its connected don't click delete driver software then unplug and replug also make sure you have full firmware to install should be a few files not just PDA in my experience
Sent via that ninja standing right behind you
aXiDroid said:
No problem, just don't rush.
Flashing CWM takes a minute, after that the phone will reboot.
To enter to Recovery mode press Volume Up + Power and keep it pressed for 2 seconds after Samsung logo will appear.
BTW: If you encounter boot loop don't panic, just clear cache, data and dalvik and everything will be ok. I fixed boot loop on my phone by doing so.
edit: could you please press the THANKS button if I helped?
Click to expand...
Click to collapse
Hi,
I cant run right now into CWM there is no CWM installed. Also I dont have SD Card on phone, is this problem?
Pretty sure cwm is either part of kernel or in some devices installed to system
Sent via that ninja standing right behind you
Latrop said:
Make sure you run Odin as admin and also try uninstalling device through device manager whilst its connected don't click delete driver software then unplug and replug also make sure you have full firmware to install should be a few files not just PDA in my experience
Sent via that ninja standing right behind you
Click to expand...
Click to collapse
You are right but it wont.
I am tryin to install this package: I9001XXKP4
PDA(PDA FILE), PHONE(Modem file), CSC (CSC FILE), PIT(PIT FILE) and Boot_loader
but its the same it stock.
Don't do bootloader I'm pretty sure and how long did you leave it cause once it took 15mins setup connection for me if you still don't prevail only option is try another computer
Sent via that ninja standing right behind you
You are talking about ClockworkMod, yes?
It replace Samsung's Recovery, if You flash it with ODIN there is no way it wouldn't run. Just turn the phone as I wrote before: Vol UP + POWER, and keep them pressed for 2, 3 seconds after Samsung logo appears. This will take you to recovery mode, and by so to CWM.
I'm using "recovery-clockwork-5.5.0.4-ariesve.tar", but the latest one is: "CWM6012-TOUCH-CM9-recovery". As far as I know for this moment.
There is the same also with Windows7 it won't flash.
noc1 said:
There is the same also with Windows7 it won't flash.
Click to expand...
Click to collapse
Have You installed Kies?
Download the newest, with is 2.3.3. Install it, reboot, put the phone in to download mode, turn the ODIN, select the files, connect the phone and hit the START button.
No way this wont work! I did so many times.
aXiDroid said:
Have You installed Kies?
Download the newest, with is 2.3.3. Install it, reboot, put the phone in to download mode, turn the ODIN, select the files, connect the phone and hit the START button.
No way this wont work! I did so many times.
Click to expand...
Click to collapse
I have installed Kies from official Web download samsung.
I am going to reboot now. And I will run again.
Thank you.
Latrop said:
Don't do bootloader I'm pretty sure and how long did you leave it cause once it took 15mins setup connection for me if you still don't prevail only option is try another computer
Sent via that ninja standing right behind you
Click to expand...
Click to collapse
I have wait about 18mins it stockat Setup connection..
Have you try to flash simple rom file onto the phone? Or Are you flashing the PDA file?
With "One Package" there shouldn't be any issues.
aXiDroid said:
Have you try to flash simple rom file onto the phone? Or Are you flashing the PDA file?
With "One Package" there shouldn't be any issues.
Click to expand...
Click to collapse
it doesn't work
can you please find me someone some pda or One package files for flash
noc1 said:
it doesn't work
can you please find me someone some pda or One package files for flash
Click to expand...
Click to collapse
You can download original newest Samsung's package from www.samfirmware.com - just create an account.
Download depends on Your country.
Download the file, use ODIN and select "One Package". Aries file will be needed to.
noc1 said:
I dont have CWM installed. I can join only in Download Mode,
I am trying to install via PDA file with ODIN 1.85 it said:
ID:0/013> DO NOT TURN OFF TARGET!!
<ID:0/013>
<ID:0/013> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
-------------------------------------
When I try with Odin 4.43 it stocked at
<1> setup connection...
I have changed USB port on PC, nothing yet.
Click to expand...
Click to collapse
For i9001 please refer to your WIKI http://forum.xda-developers.com/wiki/Samsung_Galaxy_S_Plus/GT-I9001
you cannot use Odin 1.85, only Odin 4.43 with ariesVe.ops
IF "setup failed" in Odin its because KIES is running in system tray, you must shut it down for Odin to function
Open task manager and close:
Kies.exe
KiesTrayAgent.exe
KiesPDLR.exe
further reference refer to My Android Solutions link below