I just got a att tilt.. I have tryed to unlock it using the kaiser sim unlocker. At first it would just go to the load screen and it would say 0%... a white screen. so i looked for a posting with that. And i found this ------HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)-----
on that i got all the way up to 95% and then I got a err message.. now all it will do is go to the load screen (white) and show 0% and then I follow the instructions.. and when I go to restart the phone it show the red,green,blue,white screen.. top left show
kais1*0
spl-1.56.0000
cpld-8
top right show
ruunbh
what happen please help.. this is the first time this ever do this to me.. i have ren unlocked programs from hear befor with np..
bikepilot said:
I just got a att tilt.. I have tryed to unlock it using the kaiser sim unlocker. At first it would just go to the load screen and it would say 0%... a white screen. so i looked for a posting with that. And i found this ------HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)-----
on that i got all the way up to 95% and then I got a err message.. now all it will do is go to the load screen (white) and show 0% and then I follow the instructions.. and when I go to restart the phone it show the red,green,blue,white screen.. top left show
kais1*0
spl-1.56.0000
cpld-8
top right show
ruunbh
what happen please help.. this is the first time this ever do this to me.. i have ren unlocked programs from hear befor with np..
Click to expand...
Click to collapse
It shows you are using the 1.56 SPL, which is the Stock AT&T SPL.
Download the official AT&T 6.0 Shipped Rom here:
http://rapidshare.com/files/55298724/RUU_Kaiser_CINGULAR_WWE_.exe
Take out your SD card and flash this ROM. After you have a successful flash and your phone boots up normally, post back and we'll go from there.
bengalih said:
It shows you are using the 1.56 SPL, which is the Stock AT&T SPL.
Download the official AT&T 6.0 Shipped Rom here:
http://rapidshare.com/files/55298724/RUU_Kaiser_CINGULAR_WWE_.exe
Take out your SD card and flash this ROM. After you have a successful flash and your phone boots up normally, post back and we'll go from there.
Click to expand...
Click to collapse
Ok I tried that it go to 1% and then it go to say
ERROR[294] : INVALID VENDER ID
this update untility cannot be used for you pda phone pleas check you Update utility
bikepilot said:
Ok I tried that it go to 1% and then it go to say
ERROR[294] : INVALID VENDER ID
this update untility cannot be used for you pda phone pleas check you Update utility
Click to expand...
Click to collapse
You could try this
More specifically, might want to read this whole thread and search it for RUUNBH.
MTTY should be able to help as long as you use the proper commands.
bengalih said:
You could try this
More specifically, might want to read this whole thread and search it for RUUNBH.
MTTY should be able to help as long as you use the proper commands.
Click to expand...
Click to collapse
Ok got it back to all origanal...now every time i take the battery it go back to the colar screen ( now what
hello!
I am new here and i got one big problem.
So please help me!
I tried to flash my tytn II with this rom(ENDED- 28/V/2009 Anryl WM⑥.⑤ 21725 FINAL ULTIMATE(101RAM) -ENDED- ), but when i finished the flash, my phone want to boot. It stops on black screen and show "HTC"
If someon know how to fix it, please help me!!
R 1.27.16.21
G 22.52.88.13h
D 3.34.00.00
did you flash jumpspl and hardspl first?
Yes i did.
I did everything like it said in http://forum.xda-developers.com/showthread.php?t=433835 and my phone is stuck in bootloader. So how can i reflash it? i tried to flash it again with sd card but when i use power + camera + stilus to get bootloader, in a second there is a white screen where is written that there is no image, and it go back to three color screen mode, and in the bottom is a white screen where is written "serial"
When i try to flash it with activesync there is an error 262. I spend a lot of time reading many posts here, but i did not find enything what help me.
Any sugestions?
Thanks!
Bro, did you solve it? please let me know. Same issue and as described in the faq's tried using MTTY but that one also does not connect.
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Before I flashed my first rom, I read wiki.xda-developers.com to make sure I understood what I was doing, and used the search button, instead of risking turning my phone into a paper weight.
Since then, Crackwhore has written a very helpful post at the top of this forum about how to use HSPL and USPL to allow you to flash roms.
yeah i know all that. not my first time flashing a phone but the first time it got stuck loading the bootloader. and specially when i´ve only used the HTC update.
darfor said:
Im about to flash my ROM from original 1.56 to Duttys new, but when i enter bootloader the white loadingscreen gets stuck in my face. Nothing happens and i need to remove the battery to shut down device. Anyone? Freakin frustratin´.
Click to expand...
Click to collapse
you mean you couldn't get to boot loader page?
So you already have HSPL 1.56 installed (or have SPL1.54 and used USPL)?
If you have HSPL you could try renaming the .nbh file to blacimg.nbh and copying it to the SD card and entering bootloader
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
AFW said:
Same problem here. Stuck in bootloader mode. Loading progress indicator never moves beyond 0%. Have always used the card method (blacimg.nbh), but this time it doesn't work and nothing flashes. No matter what I do the system goes to tricolour bootloader screen and says ROM update error. Have tried 3 microSD cards, all in working order, so this isn't the problem. The full problem description is here. Help!
Click to expand...
Click to collapse
try dnloading the rom again amd try.
the file might be corrupt
Have tried that many times. File is not corrupt. I'm getting really worried this is now a brick...
OK, if you can get phone into bootloader, it is not bricked
What does your SPL say in bootloader? Do you get any errors when trying to flash rom? Are you using USPL or HSPL? If USPL, you have to use it before every flash to new rom or radio. If HSPL, are you using correct version?
Was on Dutty's 3.9 XT, but decided to revert to standard WWE 1.56. I flashed the Std 1.56 ROM successfuly, and then tried to restore the ship SPL 1.54 using the card flash method. This failed, and now I'm stuck on the bootlader screen forever.
No matter what I do the THD always goes to bootloader (red-green-blue-white screen), with following text:
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
Upgrade ROM code error
Please try again
USB
Click to expand...
Click to collapse
When I start blac_uspl.exe (USPL 2.5), a window flashes (Vista64) for a split second and then nothing else happens. The Vista64 system's USBs work with THD and have been used to sync over past few months.
When I try to run HSPLWrapper_Blackstone_156OliNex.exe and step through the preliminary screens, the Verify that you want to update ROM version screen has the From Image Version as blank and the To Image Version as 1.56.Olinex. When I click to commit the flash the THD screen switches to white with a progress indicator that always stays at 0% until it times out. Recovery does nothing and the same thing always happens. Using Vista64. .Net installed and fine. I can't use the card method (BLACIMG.NBH) - the system also stays on "Loading .... 0%" and nothing else happens.
When I try to flash anything (have tried HSPL1.56, Dutty's 3.9 ROM, stock 1.54 spl) using the card method, the system says "Loading . . ." and hangs there forever without a progress indicator showing.
Your SPL says 1.54.0000. When you try and run USPL.exe have you remembered to disable your antivirus?
Have you tried usb method instead of card for flashing rom?
I know you have said that youi have used usb for syncing, but when in bootloader does it change from 'serial' to 'usb' when you connect HD to PC?
Fallen Spartan - I want to thank you for taking the time to help me resolve this problem. Very much appreciated!
1. Yes, anti-virus disabled and indeed removed from the PC.
2. Yes, have tried the USB method at least 20 times.
3. Yes, the bootloader changes from Serial to USB. It then goes to the progress indicator screen and hangs on 0%. The progress indicator on the RUU on PC also stays at 0% and eventually times out. I've gone through the Recovery routine at least 20 times, with no luck.
When I try to run SSPL-Manual-TouchHD.exe it says "not a valid Win32 application".
I'm a bit perplexed by this.
You have obviously successfully flashed Duttys V3.9 so drivers are fine, you know how to use USPL, both flashing methods (SD card and usb/pc), disabled anti-virus, phone in bootloader.
Have you tried to reflash 1.56 rom or possibly performing a hard reset before trying to use USPL or HSPL. I doubt this would make a difference though.
Have you tried cRaCKwHoRe's USPL GUI v 2.5 Application?
You don't get any code errors?? I'm struggling to find a solution here.
Yes, this is most vexing. I've flashed innumerable times before and never had an issue. I suspect the SPL is fine, but somehow the actual WM ROM image is corrupted. Will now try to load Std 1.56 ROM image again...
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa (though I'm a rugby fan).
AFW said:
Success! The 3rd attempt at reflashing stock 1.56 ROM worked. I don't know why the system bombed out before. Perhaps one of those inexplicable brain farts..
Anyway, all seems to be fine now. Fallen Spartan, you have my endless gratitude for at least responding. Let me know if you need accommodation at next year's FIFA World Cup in South Africa.
Click to expand...
Click to collapse
No accomodation required, just glad you got it sorted
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
can anybody help me at all
Adamsville: perhaps you're stuck in bootloader mode because the WM ROM image flashed on your system has become corrupted or disabled, ie the only thing the system can boot into is the bootloader.
Try flashing a new compatible WM ROM image and see if that works.
AdamsvillE said:
Im still stuck. When i installed HSPLWrapper_Blackstone_156OliNex my screen changed colors but would go back to normal when i would turn the screen off and back on so i didnt see it as a problem. I installed the EnergyROM BLACKSTONE 20090608 Standard an tried to go back stock using RUU_BlackStone_HTC_WWE_1.14.405.0_Radio_52.49a.25.26_1.09.25.14_Ship but it gets to 1% then says this update utility cannot be used for you PDA phone. Please check your update utlity.
Then the phone boots up and at the black smart mobility screen in the bottom corner it says
R 1.09.25.14
G 52.49A.25.26U
D 1.14. 21010
the phone boots up with the funny colors again and goes to align screen but it keeps staying there even after i align it.
The bootloader screen says
BLAC100 32M
SPL-1.54.0000
MicroP-BlackStone (LED) v6
USB
Am i tryin to install the wrong stock ROM. I purchased the HD from phonesource-usa if that helps also
Click to expand...
Click to collapse
a hardreset followed by a 1.54 base rom will solve all ur probs.
or lower spl to 1.14 cos ur stock rom is a 1.14 base as suggested by th name..
cheers
Hello! I got a problem a couple of days ago with my Xperia. Whenever I try to load it i get the "Alien battery" dialog. I searched and found that reflashing it would probably fix it. I am not sure if flashing the phone means putting a new rom on it, but that is what I did. The rom worked but the problem was not fixed. I didn't know what to do so I accidently put a stock SPL rom file on my phone and installed it. I realized what I had just done when the progress bar had reached about half way through. When i start the phone with any Kovsimg.nbh file on my memory card the phone boots up with the "rainbow screen" and goes to a gray screen with blue text saying "Loading . . .". If I boot without Kovsimg.nbh or without memorycard it says something like "Loading . . .
Image file not found " and then it goes back to the "rainbow screen" except that it says "Serial" at the bottom of it. Have I destroyed my phone or is there any way to fix this?
Edit:
This is what the "rainbow screen" says, without sd card:
RUUNBH
KOVS110
SPL-0.072.0000
MicroP1-787
MicroP2-707
Continye to Upgrade ROM
Please wait...
Serial
Click to expand...
Click to collapse
Bump (The number of viewers stopped increasing.)
Bump.
Any Replies are appreciated.
I fixed it. I updated it with SEUS.
how u fixed fred; cuz i'm facing same problem but my configuration on the rainbow screen are different; do write briefly so novice like me can understand....thanx in advance
hello!i have an htc touch diamond 2 and i used hard-SPL in order to put a new rom to my device.i did it successfully(at least pc said so) and then i installed a rom energy topaz successfully too.but when it was done my device restarted on its own and it cant boot.the only thing that it does is to appear the htc green logo in white screen and then restarting again and again and again!!i kept the volume down button and it booted on the red-green-blue-white screen and it says this:
TOPA100 32Μ
SPL-2.51.oliNex ------>on the red part
MicroP-Topaz (led) V10
TURBO HW/TURBO SW
TPMFG DATA
517,557 190,896
186,212 854,214 --------->this one one green part
847,894 calibrated
and on the white part it says usb when its connected with pc and serial when its not!!what can i do now?i tried also some other roms for topaz which were succefully loaded too but the same thing happens again and again.i would apriaciate some help.
thanx.
billyprepo said:
hello!i have an htc touch diamond 2 and i used hard-SPL in order to put a new rom to my device.i did it successfully(at least pc said so) and then i installed a rom energy topaz successfully too.but when it was done my device restarted on its own and it cant boot.the only thing that it does is to appear the htc green logo in white screen and then restarting again and again and again!!i kept the volume down button and it booted on the red-green-blue-white screen and it says this:
TOPA100 32Μ
SPL-2.51.oliNex ------>on the red part
MicroP-Topaz (led) V10
TURBO HW/TURBO SW
TPMFG DATA
517,557 190,896
186,212 854,214 --------->this one one green part
847,894 calibrated
and on the white part it says usb when its connected with pc and serial when its not!!what can i do now?i tried also some other roms for topaz which were succefully loaded too but the same thing happens again and again.i would apriaciate some help.
thanx.
Click to expand...
Click to collapse
Sorry i didn't get back to you sooner and you added the perfect amount of info
ok where to start - firstly have you tried a hard reset after flashing the ROM this isn't always needed but may possibly free something up to make the energy ROM work. You could also try flashing back to a stock ROM from the HTC website and then re-flash the one you want after everything is ok on the stock ROM.
when you say successfully loaded do you mean the screen shows 100% (phone not computer) or does it say complete as it can say 100% on the screen for a little while and not work ? I don't do mine by the PC i use a memory card to flash it and mine always comes up complete when done and then press a key to restart the phone.
failing all of this head back into the hard_spl thread run the spl_relocker in the first post and once relocked flash with hard_spl 1.83 no idea if the newer version is less or more buggy but i use 1.83 and it's smooth sailing.
You could also try flashing from a memory card instead if you have one to hand
thanx warlordxxx!its done!
billyprepo said:
thanx warlordxxx!its done!
Click to expand...
Click to collapse
No problemo