Hello,
I have a Samsung galaxy s captivate and I now the ROM v6 continuum in 2.3.4 ... I wanted to stock rom using ODIN3 but its blocked in factoryfs and it makes a green screen I unplug the usb and remove the battery .. Now I can not open my samsung what can I do?! Help me I just buy it at a guy and he is in mid 2.3.4
I'm having the same problem, but mine won't go past the Galaxy S Samsung.
keep trying odin and it should work
Sent from my GT-I9000 using XDA App
I can not do anything.... I visited all the forums, but there is a solution, but I do know if the usb jig would work .. Because all youtube video showing usb jig with the problem of the panel exclamation between the cell and the computer, but they do not show the same problem as me
Thing is IF a jig wont fix it you will have to send it to get fixed with a Jtag. Jig can be made with little cost (made mine for about $2.50) or buy em already made for $8-$11.
Keep in mind when I say the jig can fix i mean it can force your phone in to download mode.
-Pull battery
-Plug usb cable
-Put battery & hold Vol+/Vol-
If you can't go in download via this method you need a usb jig to force it.
Then reflash with Odin until successfull. You just had a bad flash and a bad fs will not let you boot the phone normally and use the button combo to go into download so you need to bypass with the usb cable method or the jig.
v-sasuke said:
Hello,
I have a Samsung galaxy s captivate and I now the ROM v6 continuum in 2.3.4 ... I wanted to stock rom using ODIN3 but its blocked in factoryfs and it makes a green screen I unplug the usb and remove the battery .. Now I can not open my samsung what can I do?! Help me I just buy it at a guy and he is in mid 2.3.4
Click to expand...
Click to collapse
So let me get this right. You just bought the phone, then watched a video without reading anything and now your stuck. Please do your part is saving hard bricked devices. DO THE RESEARCH.
Yea flashing roms is a big deal you should be sure you read everything before tring then read it a 2nd and 3rd time. And not just info in the op all the info on your device.
Good luck
Sent from my GT-I9000 using XDA App
Related
A few months ago, I had a few issues with my I9000.
I had Darky's Rom 10.1 at the time, and decided to go back to a generic rom.
Went to Samfirmware and downloaded I9003XXKP9.
It seemed to flash correctly, but on completion, Odin showed "reset", but no "pass".
The phone wouldn't power on at all, no download mode, no recovery.
My PC won't recognise it at all.
It was only later that I realised I'd installed a I9003 rom onto my I9000.
I've tried every button combination, with and with out a PC cable and battery, no reaction. Also tried a JIG I got off eBay. Works on my Galaxy S2 and my brother's Galaxy S, but not this this phone. It will charge if I connect it to a wall charger however.
I brought it to a local phone shop who used a JTAG, but apparently although they were able to get it into download mode, once they reflashed, it still wouldn't power on, no matter which rom they used. They worked on it for about a week.
I'm just trying to figure out if this phone is recoverable. It was only about 2 months old when this happened, and it looks almost new.
Many thanks for any information anyone can give!
Anyone have any ideas?
So in my point of view.
When they used to try the JTAG and the phone would not start up the motherboard / bootloader is corrupt.
No way to change that back.
May you send the phone to samsung and they are able to restore that device.
No other solutions in my point of view.....
You could try this:
http://forum.xda-developers.com/showthread.php?t=1330491
http://www.jtagbox.com/jtag-news/riff-jtag-samsung-galaxy-i9000-unbrickrepair-bricked-boot
Hi,
Go to Youtube and search this :
"How I did: Restore soft-bricked Samsung Galaxy I9000"
phil_greg2001 said:
Hi,
Go to Youtube and search this :
"How I did: Restore soft-bricked Samsung Galaxy I9000"
Click to expand...
Click to collapse
A soft brick would usually mean the phone powers on
disclaimernotice said:
You could try this:
http://forum.xda-developers.com/showthread.php?t=1330491
Click to expand...
Click to collapse
Do what the guy says. the method is BULLETPROOF
it must go on ^^
Buy an usb jig on e-bay or make your own. This is just a 301ohms ressistor on pin 4 and 5. It should give ypu recovery mode.
Sent from my GT-I9000 using xda premium
no panic , it's not over i know this problem but you can fix it here are some tut's to repair your phone good luck
WOW
I haven't been on in a while - can't believe how many of you have taken the time to respond!
Just reading over the replies now, and will definitely be trying them out!
ok plug charger into wall and try get download mode it works for me but any function when not plugged in or plugged to laptop wouldnt work so hardbricked but like i say try to force it in download mode when plugged into the wall
Hello,
I tried to flash back to the stock ROM of Galaxy S and then install a new Jetpack 8.2 custom ROM.
Apparently, since I did a bad search on the internet on finding a stock ROM and pit file, i downloaded a pack from xda with the .pit file pda file phone file and CSC file.
I DONT REMEMBER which it was..i selected all the files from the pack through odin and re-partitioning was ticked (i saw it after the flash finished).
So when the processes was completed waited a bit and since the phone was not responding i pulled it out.
Now that's it.. The screen is black - wont power on - wont go into download mode - wont show battery charge while the USB cable is on - nothing (AND YES THE BATTERY IF FULLY CHARGED).
Is there anything i can do to fix it?
p.s: havent tried a usb jig but from searches i made on the internet and on xda forums ppl said it will prolly not work. are there any instruction on how to make one (link would be appriciated)?
Thanks in advance
Best option would be to try a Jig (you can buy one on ebay or dealextreme) and see if you can go into DL mode. Sometime the button combination for Download mode changes depending on the firmware. Try pressing the middle of the volume rocker and power at the same time.
If not wait for a Jib or build yourself one. There should be instruction in this forum on how to build one.
if the jig doesn't work, i would try and return it to the store you got it. I know its a long shot, but the same thing happened to me and I brought it back and she just gave me a new phone! Its worth a shot!
evanogrady said:
if the jig doesn't work, i would try and return it to the store you got it. I know its a long shot, but the same thing happened to me and I brought it back and she just gave me a new phone! Its worth a shot!
Click to expand...
Click to collapse
Worth a try. Just tell them it suddenly stopped working and you have no idea what's wrong. It's not like they can power it on and see that you failed flashing it or something. and even if they use a jig they can only get to download mode and reflash it...
even if they say no... a jig costs like $1.5 on eBay. search for "i9000 jig".
Insert if, press the power button and poof, you're in download mode,
the thing is that the phone is not under any warranty or something and the store i got it is far away now !!
JTAG service if you're in the UK: http://www.fonefunshop.co.uk/
The JIG won't work when you brick with a black screen (i.e. bootloader corruption, so no boot at all).
Your only solution is to JTAG it or sadlly, throw it away...
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
immortalcy said:
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
Click to expand...
Click to collapse
As long as your bootloader is intact, the jig will get you to the download mode
Wrongly flashed i9000 with i897 rom has been confirmed to work with the jig, but i don't know i9000 with i9003 rom...
Or you can apply the unbrickable mod if your phone's warranty was voided already, if not, send it back to the shop.
immortalcy said:
Hello,
Now that's it.. The screen is black - wont power on - wont go into download mode - wont show battery charge while the USB cable is on - nothing (AND YES THE BATTERY IF FULLY CHARGED).
Click to expand...
Click to collapse
Had that also yesterday putting a new ROM on my GS. The process of writing the PDA halted.. Black screen, no way to start it up en no screen indications of charging etc..
I removed it from my USB, Removed the battery a few times did the three way download mode trick several times and finally I got the download mode screen from where I successfully loaded the new ROM.
So try a few times.. even when you get a black screen !!
let me be clear once more..i downloaded a complete I9003 rom pack from xda... some guy posted..i just missed that it was I9003 and not I9000..
and on odin re-partition was clicked..but the process was completed successfully even thou after that the phone wont start or go into download mode :/
i used not only PDA and PIT files but 2 more was included as well :/ so what i am asking is if this could really have damaged the bootloader or not
immortalcy said:
I used a I9003 ROM to flash it !!
Maybe there is still a solution?
also from what i've found on forum sometimes the JIG helped ppl who had a black screen to go into download mode. so how can you be so sure? @ Dan_Aykroyd
Click to expand...
Click to collapse
Of course you're bound to brick it flashing a firmware for a phone completely different to yours...get a jig if you're confident or take it to a service centre
Sent from my GT-I9100 using xda premium
dk206 said:
Of course you're bound to brick it flashing a firmware for a phone completely different to yours...get a jig if you're confident or take it to a service centre
Sent from my GT-I9100 using xda premium
Click to expand...
Click to collapse
Try jig first.
Next try JTAG or UNBRICKABLE mod.
Then Try a service centre.
in case it wokes up.. anyone has links for stock rom and pit to flash with odin?
thanks again
There are some ways, when already got into DL mode is best to reflash with 812.pit file and then again with 512.pit file. After I bricked my phone and got "death" screen (God I was crying) I found way of taking up DL mode (hopefully SGS is pretty-hard to brick). Others than that try to connect to your phone via usb (remember to first inset usb and then battery) and hold ALL of the buttons on your phone. Screen must flash about 3 times and then release volUp to get DL mode combo. I hope that will help you as me.
Taxiozaurus said:
There are some ways, when already got into DL mode is best to reflash with 812.pit file and then again with 512.pit file. After I bricked my phone and got "death" screen (God I was crying) I found way of taking up DL mode (hopefully SGS is pretty-hard to brick). Others than that try to connect to your phone via usb (remember to first inset usb and then battery) and hold ALL of the buttons on your phone. Screen must flash about 3 times and then release volUp to get DL mode combo. I hope that will help you as me.
Click to expand...
Click to collapse
Any updates on this ? cause I'm also having the same issue!
Dan_Aykroyd said:
The JIG won't work when you brick with a black screen (i.e. bootloader corruption, so no boot at all).
Your only solution is to JTAG it or sadlly, throw it away...
Click to expand...
Click to collapse
Are you 100% sure the JIG wont work if bricked with a black screen. Are there any other possibilities to unbrick the phone. I really need this phone back or my dad will kill me..
So I accidentally flashed an AT&T firmware (Captivate) on a Korean-Type Samsung Galaxy S. To be more specific and detailed, I've written everything below.
Firmware Flashed: 2.3.5 SGH-I897_I897UCKJ1_UC_ATT
Phone I Flashed: SHW-M110S)
My Problem: I ca'nt get into download mode to flash the correct firmware to get it to boot correctly. It turns on, and I can get into recovery mode, but not download mode. The phone turns on, and goes through all the startup screens, but gets stuck on the colorful "S" screen, then reboots again. The second time it boots, it goes past the "S" screen then the screen just turns black. I have no idea what to do.
Any help? Advice? Or suggestions?
Thanks so much in advance
Do you have CWM recovery? If so you can copy a rom in the sd with your computer, plug it in the phone, mount the external_sd and load it from there.
Else, you can get Download mode with an usb cable, search in youtube, there are some interesting videos.
May be you need Usb Jig to go into download mode Instructions below
Needed materials:
1)SgS I9000 (obviously)
2)Microusb Pin with 100*3ohm+1ohm Connected in series to pin 4 and 5Diy tutorial here(otherwise buy it in ebay)
remove your battery fro about 2 min then plug in the usb jig it powers on automatically otherwise just do the normal vol down+enter+power
viola we got download mode
after that download your rom thru odin using a pc
Sorry for my bad English,If i spelled something wrong or a grammatical mistake please correct me
bv_abhi said:
viola we got download mode
after that download your rom thru odin using a pc
Sorry for my bad English,If i spelled something wrong or a grammatical mistake please correct me
Click to expand...
Click to collapse
Your English is quite good, your French however not so..
"viola" should be "voilĂ "
UPDATE: Now the phone won't turn on at all. Not even when its plugged in to the wall or the computer...
Sent from my GT-I9100 using XDA App
Use jig method it will work
be sure to take of the battery for 1 min (check the battery voltage using a multimeter it should be around 3.7 above voltsotherwise charge it in ur phone it does charge)and reinsert it and then plug the usb jig NOT THE USB Cable and it powers on automatically otherwise boot it up using vol down+enter+power while the usb jig is connected
Thanks for the help everyone. I've decided to just buy a usb jig after all... Since most of the replies say to do so. I'll order one on ebay, but my last question is does it matter which one I get? I see a lot of Samsung galaxy s2 and galaxy s usb jigs. Mine is the Korean type i9000 and I also have an s2. Is the i9000 usb jig compatible with my Korean one? And there's this usb jig that says its for a galaxy s i9000 AND a galaxy s2 i9100, can I just buy that one for both of my phones?
Sent from my GT-I9100 using XDA App
http://forum.xda-developers.com/showthread.php?t=1129457 Take a look and decide your self
If I helped you Give me a thanks
Adam outler's unbrickable mod WILL fix your phone if jig fails.
Hi everyone. Im not normally in this section as i have an x8 but my friend has seen all the roms,mods and updates ive done so he tried to do it to his galaxy s i9000 without rooting or unlocking his bootloader. I asked him what he did he said he just tried to update software with keis but now it wont turn on just white screen with a red triangle in the middle i hope its download mode as i dont have a galaxy i dont really no but the battery has died and it wont charge im guessing hes damaged the bootloader am i right and if so whats the best corse of action to tepair it. Thanks.
You can check if it is in download mode by pluggin it in pc with odin. See the wiki page what it says about soft brick.
Soft-Bricked
After flashing a rom you might not be able to enter the Download Mode by pressing Volume Down + Home + Power. In this case a so called 'JIG' would be helpfull.
You could build it on your own: [HOWTO] [REF] Get Download Mode without 3-button combo using homemade JIG
... or buy a preassembled one on a well known marketplace.Hint: There is no difference between a JIG for Samsung S/S2 or S-Plus.
See if you can go into d0wnload mode with vol down home and power. If that works go and try to find the stock firmware for the phone and download and extract. Download odin and put csc pda and phone/modem in there rightful places. 512 pit in pit section. Pit usually comes with odin download. If not find it somewhere. Repartition checked and hit start. It should reboot when done. It will problaby take a couple of min to boot but be patient. If it starts to go into boot loop put back into download mode again and reflash. Its very hard to mess up the phone to where you cant fix it. So relax and watch tuts or whatever helps you best. I know of a link i that i will find and post for you when i do.
Sent from my GT-I9000 using XDA
http://forum.xda-developers.com/showthread.php?t=1102881
Sent from my GT-I9000 using XDA
DEAD bricked phone
So, my friend's phone (hopefully she'll stay my friend after this) was turning itself on and off all on it's own. So I (no good deed goes unpunished) suggested that I will upgrade her firmware for her. She had 2.3.3 firmware. I downloaded the odin1.7 as well as a package of all the info for 2.3.5 firmware upgrade. I flashed the phone- originally only using the PDA option with a file called: CODE_I9000XXJVS_CL565837_REV03_user_low_ship
It worked, the phone restarted and showed the firmware as being 2.3.5.
I don't know why, but I thought it would be a good idea to update the CSC and the pit and the modem as well- so I did that. when this was finished - though odin said that the flashing was successful the phone is completely unresponsive. The computer doesn't recognize it, it doesn't show any signs of life at all- like it's in the dark ages and there is no electricity in it.
HELP!!!
First question: do you think a jig will work? how dangerous is it?
second question: is there any other option to try that I haven't come across other than changing the motherboard, and if there isn't do you know where I can get one, bear in mind I live in Israel.
Please e-mail me a copy of the response to [email protected] if you can...
Odin dosnt pick it up atall plus the batteries dead aswell now and the stupid thing wont charge so i cant evan try any thing till i find away or some one to charge it but thanks for the tips.
gavster26 said:
Hi everyone. Im not normally in this section as i have an x8 but my friend has seen all the roms,mods and updates ive done so he tried to do it to his galaxy s i9000 without rooting or unlocking his bootloader. I asked him what he did he said he just tried to update software with keis but now it wont turn on just white screen with a red triangle in the middle i hope its download mode as i dont have a galaxy i dont really no but the battery has died and it wont charge im guessing hes damaged the bootloader am i right and if so whats the best corse of action to tepair it. Thanks.
Click to expand...
Click to collapse
Try to recharge the battery from other phone or use another battery.
Check whether you have the download mode working. (Home+Power+Volume down)
If yes, put phone in download mode and flash Darky RE or any other Rom via ODIN. Try to get the recovery mod after rooting and then try ROMs.
Or try restarting the phone it may work without update also. Long press power in download mode restarts the phone. However be careful.
What is the status of the device can you go to download mode
Post your firmware files name and how you choose in the odin flasher.
Dont try anything crazy you will bricked your device more:banghead:
Sent from my GT-P1000 using XDA
Alternate way to Download mode
Hi gavster26
I have been there with a buddy's phone... not a nice place.
Found a link showing this other trick ... but you have to trial and error this one on the different combos:
1. Phone off
2. USB cable pluged in
3. Odin running
4. Down (or Up - test both) Volume button + Home button + plug in the USB cable.
This booted my dead "bricked" phone into download mode.
Try it.
Well I had a problem, root days ago my Samsung Galaxy i897 (AT & T) Android 2.3.5 The root am not perfect, but after a few days stopped working. Try re-do the root and the installation stopped I had to remove the battery and slide back in the surprise was that the phone was with the yellow triangle, buy a USB JIG which is not served by the version of "boot loader" had to put oldest one ... I did then the Bootloader Changing the phone does not start does absolutely nothing Any help?
PD Sorry my bad English, Use Google Translate
If u have absolutely no signs of life, like when u plug it up to charge, etc., then u have hard bricked it and it can only be brought back to life through j-tag or unbrickable mod.
If u do have signs of life and you can get into download mode then you can flash a Stock Firmware (i897ucKK4 is the latest official release). If that works to get you up and going, you can use the [Utility] KK4 Easy Root by Red_81to get Root.
Sent from my SAMSUNG-SGH-I777 using xda premium
re
4-2ndtwin said:
If u have absolutely no signs of life, like when u plug it up to charge, etc., then u have hard bricked it and it can only be brought back to life through j-tag or unbrickable mod.
If u do have signs of life and you can get into download mode then you can flash a Stock Firmware (i897ucKK4 is the latest official release). If that works to get you up and going, you can use the [Utility] KK4 Easy Root by Red_81to get Root.
Sent from my SAMSUNG-SGH-I777 using xda premium
Click to expand...
Click to collapse
The cell phone does nothing, and to change the boot (that was what caused the problem) but to give the light button several hours after the battery gets hot (as if turned on) but the pc does not recognize it by placing the USB mode and also download anything served
PS So the solution would be a brick Full? :/
The solution or fix is in my previous post.
The problem seems to have been a bootloader flash gone bad. Flashing Bootloaders on the Captivate is one of the few real risky things to flash.
Do you recall what you flashed before the phone messed up ?? What bootloader or ??
Sent from my SAMSUNG-SGH-I777 using xda premium
re
I do remember what happened before does not turn or do anything, had loaded several roms before, but decided to charge a short while installing the installation, to switch it appeared to me the typical yellow triangle, buy a USB JIG which is not served by the the android version (2.3.5) the only solution that worked for the JIG was loading a bootloader older, oldest Download a bootloader that according served, connect the phone Odin opened the PDA and place it in load bootLoader, the cell is turn off (I had to reboot) and there did not catch more bone turn give the button and nothing happens the screen goes black, I can not enter download mode because it obviously will not start, sorry for my low English ,to connect the usb the pc does not recognize it does not leave any warning or anything like that
Not sure why the Jig did not work, even with i897uckk4 android 2.3.5 ??
Anyway, sorry....it does sound like it is hard bricked. So like I said before, the only fix would be J-tag and/or Unbrickable Mod.
Not sure where you are located, but if in the U.S. you could contact mobiletechvideos.com for repair. If your not in the U.S. then i don't know...
Sent from my SAMSUNG-SGH-I777 using xda premium