Related
hi, new member here.
bought my tilt on 10/4/07. has been flawless since that time.
used the nav quite a bit during a road trip, used a cig lighter usb charger.
got home and my battery was at roughly 40%.
put it on the charger at night went to sleep. in morning disconnected it at 8 am. shortly after i arrived at work i got the critical battery low chime. checked and it had like 7% battery life.
figured i didnt plug it in right, or it got knocked loose some how and didnt get charged.
put it in flight mode to minimize battery usage. left work at 2 30 pm (4% battery life) and put it on the car charger. got home and put it on the HTC supplied wall charger. light turned amber, so i assumed it was charging.
checked an hour later and turned phone on, it said 0%, and immediately died. left it on the charger for a few hours and the light was still amber, turned it back on and again 0% and phone immediately died and did a soft reset on its own. i turned the phone off and left it on the ac charger, took out the sim card and put it in an old blackberry to use while the battery was charging.
its been on the ac wall charger for the last several hours, i checked and the phone is totally dead, cannot turn it on, and the LED at the top is now RED.
what is the problem here? why wont this thing charge?
thanks in advance, i have alot of critical info on this device and any help would be greatly appreciated.
i cannot hard reset because i cannot turn the flippign thing on....
Does it charge when you connect it to your computer? If it does, then your charger is toast. If not, then it's probably the phone itself.
I'd try a different charger first. If that makes no difference then a different battery. If that still does not make any difference then time to exchange it.
Lidberg said:
Does it charge when you connect it to your computer? If it does, then your charger is toast. If not, then it's probably the phone itself.
Click to expand...
Click to collapse
connected to either the computer or the wall charger, the LED thats normally amber when charging, and green when charged, remains red.
I had something very similar happen to my wizard.
And as weird as it sounds, the only fix was to charge the battery in a friends wizard on his charger. I'd check the battery if possible.
Could be the battery. Know any place or anyone that will let you try a charged battery? If not, you might have to go in to an AT&T store.
i think i got it working. did some reading/browsing...
took a usb wire and cut the mini usb head off. dissected it and found the the red and black charging wires. took out the battery and held the leads to teh battery while the other end was plugged into a USB/AC adapter wall charger from a old blackberry. after manually charging the battery for several minutes, i put the battery back in the phone and the phone started up. now it seems to be charging off the wall charger and the led is now amber from red.
thanks for all your help/suggestions.
well it worked briefly. the amber light has gone back to red and it seems that the battery is not charging.
dont know what happened to my perfectly functioning phone.
tiltyoself said:
well it worked briefly. the amber light has gone back to red and it seems that the battery is not charging.
dont know what happened to my perfectly functioning phone.
Click to expand...
Click to collapse
Repeat this proceedure but this time do not turn the phone on, just plug it in to the wall charger once you have zapped the battery again.
Turning your phone on probably just caused the already recovering battery to die whiles it is trying to take on a charge.
It is mentioned quite a lot on the boards that Li-Ion Batteries do not like being over disscharged and there is usually a little protection circuit in the battery to provent complete disscharging although this circuit may be on board the phone. Completely disscharging a Li-Ion cell will kill it stone dead and it will need replacing.
When you took the battery out and so called jump started it with your flying leads, this possibly reset the little protection circuit in the battery so it can now take on a charge. I feel that once you turned on the phone, this was to much for the already depleted cell to take and possibly re-tripped its inbuilt circuit.
If you do manage to recover you cell, in future it is good practice not to let the battery go below about 25%. Li-ion cells are generally happy being top off regularly.
I hope this helps buddy
Do let us know!
Cheers
C.
thanks, that was very helpful.
ive tried defibrillating this battery out of the dead several more times to no avail.
ill try it one more time when i get home from work, if its a no go i will go to teh att core store. the phone is 6 weeks old, dont know what they can do for me if the battery is toast...
That Sucks! I hope they'll give you a new battery.
tiltyoself said:
thanks, that was very helpful.
ive tried defibrillating this battery out of the dead several more times to no avail.
ill try it one more time when i get home from work, if its a no go i will go to teh att core store. the phone is 6 weeks old, dont know what they can do for me if the battery is toast...
Click to expand...
Click to collapse
I had exactly the same problem with my battery. It came on though after a day. Although the battery life after this happened went down to 10hrs max on standby. I sent the phone back and got a new one and now all is fine.
This is a problem that affects almost all makes of phone. There are three (main) causes of the problem:
1.
The battery charge drops too low to allow the charging circuit to recognise a battery is even in place (red no charge light stays lit)
possible solution:
http://forum.xda-developers.com/show...22&postcount=6
(in the end very similar in the end to the USB wire used in post above)
2.
A faulty battery (but if you can charge it using a cut usb cable or using a couple of AA batteries this may not be a faulty battery.
3.
A faulty charger OR a charger not delivering 5v at 1000mA as the OEM one does. Many chargers that are used for other phones or generic chargers only deliver 500mA. This is not enough when your battery drops very low. (these chargers are OK for occasional use but I do not advise using them regularly particularly if the no-charge syndrome has shown itself)
4.
A faulty USB connection on the phone. I have now seen a couple of reports where the fine wire connections in the phones USB port have become bent out of place.
Number 4 above is at least possible for the OP as it seems the battery will charge using a cut USB cable but not when either the PC USB cable or mains charger is connected. A USB port on the phone with a a bent internal contact would explain what's happening.
A previous poster was able with a needle or similar to bend the contact back into place.
Mike
i had the same problem with my phone.
put it in the charger overnight and woke up in the morning and couldnt turn on the phone with blinking red light. I don't know if my battery was over-drained though. I went to AT&T and was playing around with their charger and new battery and somehow the so-called dead battery started working again. They changed the SIM card on my phone there and then i haven't been able to use the phone since. I've changed the network to GSM instead of Auto setting under Phone Options which allows us to make calls; but now I can't connect to 3G network.
Charging thru mini usb
My phone started to exhibit similar problems...plugged in but no charging of the battery. I finally realized that my mini usb connection on the phone has been compromised (bent, distorted=not functioning properly) Now I have to prop the mini usb connection up at a slight angle to engage the charge. I think the plastic/metallic connector on the phone is somewhat fragile ...I had similar issues with my hermes.
called customer support.
they are sending me a new phone and battery.
how do i know its not a refurbished one? any clues?
before u send out your defect phone, have u check if your phone's mini-USB connector has bent or misaligned pins?
yeah all the connectors visually are fine.
Well I'm at about 2% battery life, and it will not charge. I'm using my computer to charge it. Charging it from the wall hasnt worked for me for a while, not sure why.
Anyway I was wondering what it can be? I doubt my battery's dead or something is wrong with the phone... I'm sorry if this question's been answered, but I couldnt find an answer on google.
If USB charging works, but not charging with the AC adapter then the adapter is either bad, or plugged into a bad power outlet.
Nope it's neither of those because Ive tried two working AC ountlets and two warking cables. However, that's not my problem, my phone died and I can't charge it :-/
Ya so the phone died. It didn't look like it was going to charge on the USB, really weird. Anyone ever have there phone refusing to charge? While it was alive I tried to run activesync; that didn't work. So what should I do?
Btw, I've had the phone for a couple months now and I haven't had any big problems. I don't think it can be my phone failing, worst case just the battery. I've had something similar before but it fixed itself, doesn't look like thats happeneing now.
Battery
Maybe charging from the computer wasn't such a good idea. I recommend changing the battery and the charger and always be a nice boy and charge from the outlet ::- ).
I had the same thing happen to me - the connector at the bottom was broken. I had to do a return to factory. I looked (using a magnifying class) at the bottom of the phone and clearly see a crack in the connector.
It doesn't charge from the outlet.... I kinda just explained that lol
jrd said:
I had the same thing happen to me - the connector at the bottom was broken. I had to do a return to factory. I looked (using a magnifying class) at the bottom of the phone and clearly see a crack in the connector.
Click to expand...
Click to collapse
Hmm my connector does look a little bent. However it would of had to be like this before, and it was charging until I let my battery get to 5% :-/
I had a similar problem with my Kaiser a couple of weeks ago - it started to crawl and a soft reset took over 15 minutes to come back up to a working state, after which the battery wouldn't charge. It definitely wasn't the charger at fault as that still works on my TyTN. Phone was about 3 months old, so called Vodafone UK who seemed to think it was software related and so provided next day swap out. Old battery works in the new handset so never did get to find out if it was hardware or software that caused it to die.
Here's what probabally happened... you meant to stick you stylus in the reset hole and accidently put it in the usb hole... thus bending your charging port. I did it and when I plugged it into my car it would actually discharge the battery.. but when I plugged it into an outlet it just wouldn't charge.. if I were you I'd go see if it charges in a car
I appear to have a similar issue when charging from PC usb, and have identified that if I put pressure up or down on the charger it will charge the kaiser. But if plug in the charger without applying directional force it will not charge. Currently i have a small weight resting on the mini USB chargin input.
So obviously something up with the connector. But I haven't jammed anything up the usb port to my knowledge. Are these ports really that flimsy?
Tilt owners: If charge mechanism breaks, is ATT cool?
Oh no, now I can't charge or sync my Tilt.
My power is slowly running out.
What do I do? This is covered by manufacturers warranty in a year, is
ATT going to take my Tilt back and give me a new one?
I need my phone to be working and working well.
Thoughts?
axonn said:
Maybe charging from the computer wasn't such a good idea. I recommend changing the battery and the charger and always be a nice boy and charge from the outlet ::- ).
Click to expand...
Click to collapse
Charging from the computer should be better than the wall, given that the USB ports on the computer have a 5.5v output, while wall chargers have 5v.
My battery died last night and i charged the phone up and now the phone will not turn on anymore. Anyone have any ideas cause i'm completely out of them???
have you tried takin git out an putting in the phone again?
Yup. I dunno what is going on. I was using sony's cable to charge the thing and the power button was lit up red and now i switched to a different cable and the power button doesn't turn red anymore but the indicator lights are flashing like it doesn't have enough power to start. It may just be dead and sony's cable just stopped working and never charged the thing
Nope that isn't it... it just won't power on for some reason. i hope someone has an idea as to what is going on because i don't
I had a similar problem and had to leave it plugged in for at least 10 mins before the LEDs indicated it was charging.
THANK THE LORD THANK THE LORD. I was right. The crap cable sony uses just didn't charge the phone at all. Now that i switched i was able to turn the phone on again.
Try hard reseting the device while it is powered, might do something if its a software issue.
battery stone dead~won't recharge
I have the same problem. I don't believe ti has anything to do with the cable. The first time it suddenly came to life after a day or two fo being dead, but this time so far it is still in a coma. It did briefly awaken when connected to the pc, but it kept blacking out, and now it's completely gone again.
Could it be that it is not set to power off until the battery is completely stone dead, and therefore it won't recharge?
I think you are absolutely right. I don't believe it allows you to charge it until it is turned on. So try and plug it for like 15mins and try and power it on. Let us know if it works
This sounds like what I have seen on more than one device. If you let the battery go completely dead it will not take a charge from a USB cable to a PC or hub, even if it was a powered hub. We had some old HTCs that would only take a charge from a transformer when the battery had been fully depleted. It was like the USB to PC or hub did not give it enough amps or watts to turn it on and start charging.
Tanquen said:
This sounds like what I have seen on more than one device. If you let the battery go completely dead it will not take a charge from a USB cable to a PC or hub, even if it was a powered hub. We had some old HTCs that would only take a charge from a transformer when the battery had been fully depleted. It was like the USB to PC or hub did not give it enough amps or watts to turn it on and start charging.
Click to expand...
Click to collapse
Came accross this also in the Kaiser forums - think it has something to do with the battery being absolutely drained, so much that there isn't enough power to switch the current to the battery again.
Never happened to me, so never quite figured it out. But the Kaiser forum had a lot of discussion (and solutions I think) on this. (Xperia has HTC involvement..or so it's rumoured).
Tanquen said:
This sounds like what I have seen on more than one device. If you let the battery go completely dead it will not take a charge from a USB cable to a PC or hub, even if it was a powered hub. We had some old HTCs that would only take a charge from a transformer when the battery had been fully depleted. It was like the USB to PC or hub did not give it enough amps or watts to turn it on and start charging.
Click to expand...
Click to collapse
yep... I have had that happened to my blackjack 2 a couple times too. everytime I had to connect it to the charger for like 10 15mins before it can turn on again... plugging it to the pc/hub never work.... also happened once to my iphone as well
Hey I just ran into this problem today.
Turns out it was activesync messing with the phone
Ended the mobile device center process in task manager and phone went back to normal.
EDIT: Ok maybe its not back to normal. But it was definitely caused by activesync...
EDIT2: Back to normal now... Had to plug in the wall charger. After a minute the charging lights flashed and i was able to turn it on.
Checking battery status, and its in the red.. I guess the activesync was just a coincidence.
But wow, I left the thing plugged into my computer overnight to charge, and apparently it drained more than it charged?
There is defiantly something extra going on with the Xperia. While other devices I’ve seen fully drained refuse to start charging again from a USB to PC cable and even some power outlet charges. My Xperia is also doing as Nipperos. With an almost full charge I plugged it into the USB to PC cable and the icon went to the little plug and when I clicked on it the status said that it is was charging but when I got ready to leave for the day it had drained down one red bar. It was also very warm. With this, the $800 price tag and the random crashing made worse by the incredibly poor location of the reset button and made even worse by the incredibly poor design of the battery cover. Really, what is the proper way to get the thing off without breaking it? I’m fighting the urge to return it.
Any word on a new firmware?
Nippero said:
Hey I just ran into this problem today.
Turns out it was activesync messing with the phone
Ended the mobile device center process in task manager and phone went back to normal.
EDIT: Ok maybe its not back to normal. But it was definitely caused by activesync...
EDIT2: Back to normal now... Had to plug in the wall charger. After a minute the charging lights flashed and i was able to turn it on.
Checking battery status, and its in the red.. I guess the activesync was just a coincidence.
But wow, I left the thing plugged into my computer overnight to charge, and apparently it drained more than it charged?
Click to expand...
Click to collapse
I've noticed this too... My phone will be on full charge, i connect it to my PC to install a software, then i check one bar's gone... it drains more than it charges...
my x1 did this today. my buddy has a verizon htc phone and let me use hus htc wall charger and it did the trick...
my x1 is a x1i so i dont know if the US. plugs or what dont agree with the phone. but out of 6 cables and chargers only 2 will charge the phone from a dead battery the other 4 would only charge after it was on.
so my best solution for you all is to find yourself a htc wall charger and let it charger for 20 mins before trying to turn it on.
and of course theres htc involvment on the x1. look in the windows folder. all drivers are HTCxxx.dll the comm manager is htc. theres a forum here the htc developers site. this isnt a site for samsungs and other makers. this is a site for htc devices. if it wasnt a htc device it wouldnt be here.
My experience
I had a similar experience while on a trip to Korea. I didn't foresee that a 200mA difference in the current output of a wall socket charger will cause me so much pain.
I had always been able to charge the X1 with my Jabra headset's wall socket charger, hence I brought it on my trip. Not being mindful of the ratings, it can only supply 500mA, which is different from the X1's charger, 700mA. I was using it happily on a bus, happily keeping it alive with a solar USB charger (till it ran out of juice too). A while later, playing with the GPS I noticed my battery power dropped to 20% (2 bar) so I pressed the power button to conserve energy.
Unknowingly, the battery kept draining and the next time I wanted to turn it on I couldn't. The top 2 LEDs gave me 3 red blinks. I thought, "ok, so I just go back to the hotel to charge it with my Jabra charger."
When I tried that, I noticed that the power button gave a constant red LED and the battery did not charge. Taking out the battery and putting it back, I noticed the power LED went off (which indicates it was going to charge) but came back out again. It never charged.
Back home, after using the supplied SE charger, the power LED went off and never came back. I tried to turn on the X1 after 15mins and it powered up, showing the usual charging LED cycles.
Lesson Learnt. Always use original accessories.
Same problem here....
I knew about problem charging totally dead battery with wall plug-in (from previous HTC). Totally dead battery was not possible to charge via USB (from PC). But I have bought xperia via ebay and didn't know the wall charger is not original SE charger... Hope to work with previous HTC charger
Tx for coming to the idea
Just happened to me :S
I had used it all day and Wifi was turned on so obviously battery was almost dead. To save battery I turned off the Xperia.
When I tried to turn it on again it wouldnt and so I connected it to the pc.
That didnt work out so I connected it to the standard charger but that also didnt work. Right now my Xperia X1 is lying unplugged on the table because someone said you should leave it unplugged for a couple of minutes.
Hopefully it will work, I only have had it for 3 days :´(
Also hope this doesnt happen everytime your battery is drained because that would be annoying as hell.
--Edit--
Ok so what I did was I removed the battery and plugged it back in. This worked and I managed to turn it on and right now its charging.
Though when I try to go to sleep mode it turns the display on again after about 3 seconds and does what I am guessing is a low battery beep (Sorry windowsmobile noob here) but then stops instantly, which is pretty stange.
ok anyone know a way to increase the power wattage from your pc to the usb device? (sounds dangerous i know), but there must be someone who has had a similar prob and was able to fix with a bit of tweaking....ill google and come back with any results
okay...i had similar problem today morning..it wudnt start.
so i left it charging for ten minutes...and now it has turned on finally.
i think the battery goes completely dead.
Sorry this was previously posted in the wrong forum, mis described as a tytn!
My son is unable to turn his tytn2 on, I think the battery has run down completely, as when I turn it on, I get the "smart mobilty" flash screen with the RGB data, then it turns off as if completely flat, when I plug the charger in, the led charging lighton the top of the phone does not light. At the moment I have tried removing the battery for a while to see of that "resets" it, I have also tried soft reseting but no joy yet.
Doing a bit of research, it looks like the fuse may have blown, I have emailed a repair company who have quoted £40+vat + £6 postage each way, which works out at £58, is the fuse the likely cause, could I get fixed anywhere else, looking on the htc manuals it would appear to definitely not be a diy fix (not for me anyway!)
Try charging from the USB cable plugged into a PC
Apk1 said:
I think the battery has run down completely, as when I turn it on, I get the "smart mobilty" flash screen with the RGB data, then it turns off as if completely flat, when I plug the charger in, the led charging lighton the top of the phone does not light. At the moment I have tried removing the battery for a while to see of that "resets" it, I have also tried soft reseting but no joy yet.
Click to expand...
Click to collapse
Sounds very familiar so far... no blown fuse involved here however, it was a blown HTC supplied original mains power supply unit in my case - the light on the power supply stopped working also. Although I could have had this replaced for free under warranty, I didn't want another of the same type (which is all HTC said they'd provide), so I splashed out on an £8.99 Power Supply from a company based in Aylesbury. It has a shiny black plastic case (nicely matching the TyTN II case), works at both 110 and 230 Volts and came with 4 interchangable mains socket adapters for use with different mains sockets around the world. Before you rush out to get another PSU however, check if the light on the power supply still works. Will the phone charge if you connect it to a PC via the USB cable and does the phone light come on in this case (note that the phone doesn't need to be powered on to charge the battery this way, as long as the PC it's connected to is up and running)? If not, you may have a damaged USB port on the TyTN II and although this can be repaired, if it's out of warranty, a repair centre would need to do the work if you're not handy with that sort of thing. HTC have a repair depot in Kingston, Milton Keynes that should be able to do this sort of thing. Depending how your results go with the above tests, you could give them a call, the number is in your manual.
I have tried 2 chargers + the usb, no lights on phone, if I plug in my TP2 it charges correctly, so I think the fault is with the phone, it is now getting as far as the windows screen then dying (presumably after standing for a day or so the battery has recovered enough to go a little further) so the fault would appear to be somewhere in the charging circuit.
Options, options
Apk1 said:
the fault would appear to be somewhere in the charging circuit.
Click to expand...
Click to collapse
Which includes the USB port on the bottom of the phone. Have a careful look for any bent or broken pins there. It's also worth searching here on xda-dev for broken Kaiser USB port threads because this is a topic which has been posted about many times.
If you don't want the expense of getting the phone repaired and can make do without a working USB charging port, you can always buy a Kaiser charging cradle that comes with an additional battery bay to use as a spare charger then just use the battery bay to charge a spare battery and swap them over when reqd. You could also use bluetooth for Activesyncing (buying a bluetooth dongle for the pc to be synched with if needed).
My sons 8925 did the same thing.. and even though his USB looked to be "perfect" it was the problem... It stopped taking a charge from it.. out "work around" involved ordering one of those phone docking stands which had a seperate battery charger and an extra battery or 2.. Then he just had to swap batteries when one died and charge it in the stand.. We did a 3 battery... 1 for in the phone, one for in his wallet so he had one to swap anywhere, and 1 for in the charger.. it worked well (and he is a heavy user of the Wifi and GPS and such)..I hope this helps you out!
Ok so this nook was bought brand new in December 2010 For my mother In-law. She hasn't used it much. So I asked if I could put Android on it? She said sure cause she hasn't used it at all. As a matter of fact the NC was totally dead when she gave it to me. So I get back to my house and put it on the stock charger. I let it charge for 2 hours. I picked it up and turn it on and all I see is this message: Battery too low to power ON. I did a search and turned up similar problems but the nc where all rooted. I'm wondering if other people have had this same problem? And what they did to solve this as it is more then likely an easy fix. A. Take it back to the store and exchange it. Or. B. Send it off for repairs. C. Someone On XDA has the answer.
Also I've done some trouble shooting like trying to reset it. Also I've used 3 Other chargers and its still not charging or turning on.
Edit: It turns on it just stays at the screen with a red battery displaying the message in the title. Also after charging for a while the screen kind of lites up like its going to turn on but only goes black after that and then comes back to the same red battery screen.
jvillejoe said:
Ok so this nook was bought brand new in December 2010 For my mother In-law. She hasn't used it much. So I asked if I could put Android on it? She said sure cause she hasn't used it at all. As a matter of fact the NC was totally dead when she gave it to me. So I get back to my house and put it on the stock charger. I let it charge for 2 hours. I picked it up and turn it on and all I see is this message: Battery too low to power ON. I did a search and turned up similar problems but the nc where all rooted. I'm wondering if other people have had this same problem? And what they did to solve this as it is more then likely an easy fix. A. Take it back to the store and exchange it. Or. B. Send it off for repairs. C. Someone On XDA has the answer.
Also I've done some trouble shooting like trying to reset it. Also I've used 3 Other chargers and its still not charging or turning on.
Edit: It turns on it just stays at the screen with a red battery displaying the message in the title. Also after charging for a while the screen kind of lites up like its going to turn on but only goes black after that and then comes back to the same red battery screen.
Click to expand...
Click to collapse
what are you charging from? are you using the stock nook cable and plug?
Yes. And charging it from the wall outlet. Did that with the stock charger. my charger from my HD2 and also tried with the charger from my vibrant. All have the same affect. It has the red battery and the messege below and it also has been a total of 6 hours of charging 2 hours each with the all the chargers.
That stinks. You may have to contact B&N for it. If your using the stock and other chargers then it must be a battery failure.
altimax98 said:
That stinks. You may have to contact B&N for it. If your using the stock and other chargers then it must be a battery failure.
Click to expand...
Click to collapse
Yeah seems to me thats what it must be I'll post back what I find out.
When that message is displayed, try holding the power button for 30+ seconds and then turning it back on.
That has worked for me the couple of times it seemed stuck on that screen.
RobertsDF said:
When that message is displayed, try holding the power button for 30+ seconds and then turning it back on.
That has worked for me the couple of times it seemed stuck on that screen.
Click to expand...
Click to collapse
Nope its not working at all. I was wondering is there an SD card that come with the NC bought brand new from B & N?
jvillejoe said:
Yes. And charging it from the wall outlet. Did that with the stock charger. my charger from my HD2 and also tried with the charger from my vibrant. All have the same affect. It has the red battery and the messege below and it also has been a total of 6 hours of charging 2 hours each with the all the chargers.
Click to expand...
Click to collapse
If you're using other chargers, it's possible that you've damages the usb port. The NC uses a non standard usb port, which has two stages. The first stage is standard 5 pin uusb communication, the second stage is non-standard 12 pin charging...
Sent from my Nexus One using XDA Premium App
Non-Standard chargers...
As far as I can tell it works fine with any microusb cord.
Their charger cables break...(bend and break) very easy. I have gone through 2.
The upside is that their charger provides power far faster than the normal microusb cords.
At this point...I'm charging mine almost exclusively from my stock evo cord.
If you don't turn off the screen when charging...it may not have enough power coming in to actually build a charge without their cable.
danger-rat said:
If you're using other chargers, it's possible that you've damages the usb port. The NC uses a non standard usb port, which has two stages. The first stage is standard 5 pin uusb communication, the second stage is non-standard 12 pin charging...
Sent from my Nexus One using XDA Premium App
Click to expand...
Click to collapse
I never used another charger besides the stock charger that came with the NC. Up until this happened all that was ever used was the stock cable for charging. I only used another charging cable once I ran into these problems cause I figured the cable was damaged. Its happened to me before with other devices. But the same results happen with every cord I use. When I plug it in it lights up and shows the red battery screen. So that tells me that the cord or USB port couldn't be the problem. Cause its clearly getting power its just not charging.
Fattychance said:
As far as I can tell it works fine with any microusb cord.
Their charger cables break...(bend and break) very easy. I have gone through 2.
The upside is that their charger provides power far faster than the normal microusb cords.
At this point...I'm charging mine almost exclusively from my stock evo cord.
If you don't turn off the screen when charging...it may not have enough power coming in to actually build a charge without their cable.
Click to expand...
Click to collapse
When charging I can not turn the screen off it's stuck on the screen with a red battery.
jvillejoe said:
Nope its not working at all. I was wondering is there an SD card that come with the NC bought brand new from B & N?
Click to expand...
Click to collapse
No. They sell it without one...the 8GB internal storage is enough for looooottts of books. The microsd was just a nice + for people with lots and lots of music.
I had this issue as well, but I found a fix!
No matter what I did or how long I let it charge, it would always have that red low battery icon.
What I ended up doing to fix it was opening up the back of the unit and disconnecting the battery cable from the unit. I then plugged it directly into the wall without the battery connected to see if it would boot, though I don't know if that was necessary, I don't even remember if it booted that way or not.. I think it did not.
Anyway I unplugged the power cable again, reconnected the battery, then plugged in the power cable and tried to boot and it booted up perfectly after that. The battery icon indicated 13% charge, but it quickly charged back up just fine.
FYI I left the unit in the car overnight right before this happened, and it was pretty chilly that night, 10-20 degreed Fahrenheit. I suspect that caused the issue for some reason, so I've been sure not to do so since.
P.S. I had to do a fair amount of googling around before I found good instructions on taking apart the NC. I think I had to take off the 2 screws under the SD card slot and use a butter knife to just pry the back off. It's just held in with clips and you can't tell it was opened except for the little stickers over the screw holes.
bstock said:
I had this issue as well, but I found a fix!
No matter what I did or how long I let it charge, it would always have that red low battery icon.
What I ended up doing to fix it was opening up the back of the unit and disconnecting the battery cable from the unit. I then plugged it directly into the wall without the battery connected to see if it would boot, though I don't know if that was necessary, I don't even remember if it booted that way or not.. I think it did not.
Anyway I unplugged the power cable again, reconnected the battery, then plugged in the power cable and tried to boot and it booted up perfectly after that. The battery icon indicated 13% charge, but it quickly charged back up just fine.
FYI I left the unit in the car overnight right before this happened, and it was pretty chilly that night, 10-20 degreed Fahrenheit. I suspect that caused the issue for some reason, so I've been sure not to do so since.
P.S. I had to do a fair amount of googling around before I found good instructions on taking apart the NC. I think I had to take off the 2 screws under the SD card slot and use a butter knife to just pry the back off. It's just held in with clips and you can't tell it was opened except for the little stickers over the screw holes.
Click to expand...
Click to collapse
Thanks for the feed back. I'm wondering by un-pluging the battery from the nook if it resets it. Kind of like if a phone freezes or if your computer freezes and you pull the battery. Seems like a plan. Not sure if this is what I'll do as I'm sure its still under warranty. If it comes back and its not covered or B & N wont replace it I guess thats my only hope.
im having the same problem as well it was off for a while and now its at the red batter screen. i guess ill try and take it apart?
CLMT said:
im having the same problem as well it was off for a while and now its at the red batter screen. i guess ill try and take it apart?
Click to expand...
Click to collapse
If your not worried about voiding the warranty then sure I guess its worth a shot.
So I got it fixed right. All it was was a faulty cable lol!
jvillejoe said:
So I got it fixed right. All it was was a faulty cable lol!
Click to expand...
Click to collapse
I had this problem too, but I'm not sure "faulty" is the right word for the cable.
My friend borrowed my nook and returned it with a dead battery (Thanks asshole). So I plugged it into my computer at work and just got the always-on low battery message. After 45 minutes I took it to my car so I wouldn't forget it. I plugged it into my USB charger in the car using a different cable. Two hours later, same state.
When I got home I pugged it into the Nook wall charger with yet another cable (not the nook's original) and got the same thing. I searched here to see if I could figure out what was going on and decided to try the original cable with the wall plug. literally two seconds after plugging it in it started booting into Froyo.
I'm sure I didn't have four "faulty" cables. I think those that are saying you should be using the original are correct. The others worked fine when the battery wasn't empty, but mine only responded to the original once it got to the point of the unending low-battery message.
Original charger / cable required with totally empty battery
Same here. With battery completely empty and non standard cable,stuck at red battery sign forever. With orginal cable, boots fine and charges.
solution I found
Have CM7 installed on SDCard, got the battery icon, even with the unit plugged into the charger with oem equipment. Held the power button 'til the unit turned off completely, removed the sdcard, rebooted. Nook booted into stock fine, turned off, re-inserted sdcard and rebooted. All is well.