hi
i have hd7 and my stupidity made me delete
HKEY_CURRENT_USER\ControlPanel\Volume
the volume value in volume folder
i was trying to correct it but deleted it by mistake
in the red bar
Pd29*** ss-bc (4K)
hspl3.1.2250.0(119314)
cotullahspl 0X07
touch s1(v2.b,#1625)
in the green bar
sd sandisk 15193mb
partition info-v211v413
in the white bar
Serial
when connected to pc USB
i tried reflashing many other different roms and even shipped roms but its not working
please help
Related
Hi everyone,
my blackstone is not booting anymore. I have changed the sd card yesterday and since then I was not able to use my cellphone.
SPL 1.54
blackStonehenge v3.4
stock sd card 8gb
Recently I have installed Gen.Y boot selector in the internal memory.
It get stuck on "starting windows" screen (modified booting image from blackstonehenge) and then it shows up a black screen. I think it freezes before Gen.Y selector.
I tried booting with/without the sd and sim. No success.
I do not want to hard-reset it because I have no backup of my contact, sms, etc.
There is a way to fix it or at least get the data from the rom?
thanks
P.S.
sorry for my bad english
It may be accessible via ActiveSync even if it doesn't boot completely.
so, i have flashed many roms in the past so im no noob. however, i haven't flashed a new rom in quite a while now maybe three months. I am doing everything i used too but i am getting 'no image file'.
i am using a fat32 formatted sandisk 2gb mem stick.
kovs110
spl-0.72.01iNex
microp1-787
microp2-707
is the code at the top of the boot screen.
rom version: dmX1_wwe
radio version: 1.14.25.55
any help would be greatly apprecriated.
benohare98 said:
so, i have flashed many roms in the past so im no noob. however, i haven't flashed a new rom in quite a while now maybe three months. I am doing everything i used too but i am getting 'no image file'.
i am using a fat32 formatted sandisk 2gb mem stick.
kovs110
spl-0.72.01iNex
microp1-787
microp2-707
is the code at the top of the boot screen.
rom version: dmX1_wwe
radio version: 1.14.25.55
any help would be greatly apprecriated.
Click to expand...
Click to collapse
You have to download the ROM from the ROM dev. section...unzip the file and then save the file on the uSD card...if needed change the name of the file to Kovsimg.nbh and then use the down vol key/power button to flash the ROM you desire...
Tk cr
thankyou for your input, however i have been doing this but im still getting 'no image file' with the Kovsimg.nbh loaded on my memory stick. its puzzling me as its never happened to me before and ive flashed around 15-20 roms
hi
I expect your sd (and it's content, incl. the Kovsimg.nbh in root dir) is correctly displayed in your file explorer?
did you experiment a little: like shutdown phone, extract sd, restart phone, reinsert sd, retry flash; something on that line?
I read a few times that this might happen out of the blue, if you can't get it working for someone having the same problem and offering a workaround
cheers and gl
Hi, PLZ HELP ME! i just have run the Hard-SPL v1 on my xperia x1, and it was all fine, but then, i Used the KovskyAdvancedRUU (Task29 mode) in order to fix broken sectors of internal memory, and the process ended OK... but my X1 have restarted, and now,i dont go further than de "Sony Ericcson" screen when i shut it on.... If i go to the BOOT screen, It just stay in the "colours" screen.. (I have the Micro SD whit the ROM named kovsimg in my device.... so, PLEASE HELP! im kind of newie....
ALso, i just have formated the Micro SD card into FAT32, and have the room in the root...
You have done all things correctly until now.
1. Can you check your ROM name at your PC whether is 'kovsimg.nbh' or 'kovsimg.nbh.nbh'? (Correct name should be only one .nbh) I guess you renamed it to double .nbh already.
2. After confirm the ROM name is correct, remove the battery and insert memory card.
3. Put back the battery then press the volume button down, and power button together and HOLD BOTH BUTTONS UNTIL TRI COLOUR SCREEN APPEAR
4. If your ROM name is correct then it should start installation.
Hope this works for you..
HAve done it like 4 times... i checked and everything was allright... i tried with 3 different micro sd and nothing happened.... At the end, i just bored of triyng with the micro sd, and installed the rom with the cellphone connected to the pc (using the RUU kovsky)... but still dont know what goes wrong with the SD....
have you pull out the usb cable from pc when in the boot screen (after you finished perform task29)?
Ok,
I read through all the related articles and tried to downgrade my TMOUS HD7, firmware as below and I believe all other users for TMOUS have same as me if update firmware normally....
So I only re-arrange articles posted by Devs to here for not to confuse....for novice users just like me !!
---------------------------------------
OS : 7.10.7720.68
FW : 2250.21.51004.531
HD : 0002
RADIO soft : 5.71.09.02a_22.51.50.21u
RADIO hd : A12.0.D4
BOOTLOADER : 5.10.2250.0(132968)
CHIP soc : 2.2.5.0
---------------------------------------
PD28110 SS-BC(4K)
SPL-5.10.2250.0 (132968)
MicroP (LED) 0x07
Touch S1 (V1.8, #1624)
---------------------------------------
I have tried below ;
[SLSPL]HD7 HTC_Europe Stock Limited SPL ROM to downgrade >=5.10.x Bootloader by ansar
But not working for me as, maybe, my HD7's bootloader is locked only SIM unlocked. It stopped after starting flashing but no affect, no brick.... so it worth to try..... (Well, in my case....)
So only one and last choice for me to take a risk was Goldcard method by viperbjk..
Problem I was faced...
1) No 1G SDCard. (Damn! difficult to get ~~)
2) No SDCard Reader can be recognized by HD7 when I connect to Y-Cable together with HD7.... I tried 4 card reader and non of them were working..
So how I did without spending more money and time~~
2G microSDCard (SanDisk), get CID with android phone and make goldcard.img as instructed by here and save created goldcard.img to notebook.
Delete the whole partition of microSDCard and create FAT 32 partition for only 512M as a primary, leave as unallocated partition for rest of the space with using "EASEUS Partition Master".
Put 512M partitioned microSDCard to notebook and format FAT32, 4096 byte using Window explore.
Make Goldcard with saved img file and copy this goldcard.img file and "SCHUIMG.NBH" after changing the file name from "RUU_signed.nbh",which I got from here for TMOUS (I choose TMOUS NoDo Rom) to microSDCard.
Power off Xperia X10 and put Goldcard microSDCard into Xperia X10, boot to CWM recovery, select as USB storage and connect to Y-cable then connect HD7 after boot into USB Host Mode to another USB conncector of Y-cable but doesn't go forward after "Loading......" message on white screen.
Took out microSDCard and put into HTC Wildfire and did same as X10 but nothing happened. Worse than X10... HD7 even not recognize at all, not even to show "Loading...." screen.... (Here, I assume that POWER IS NOT ENOUGH....)
Put microSDCard into HTC HD2 and boot to Magldr recovery, select Mass USB storage and connect HD7 on USB host mode to another USB connector...
And OMG !!!!
HD7 recognize microSDCard as soon as connect to USB connector of Y-cable and flash very fast ( just single reboot and straight to completion).
So, conclusion, as a case study.....
For who has additional android phone...
You don't need to sensitive for Y-cable... just normal sync cable will work, even without soldering... just peel off to expose copper wire 1~2 cm for each cable and join / twist tightly.
microSDCard 2GB can be used... to make sure, just make a partition for 512M.
I assume that android phone's own power supplying is important to be recognized by HD7 as a USB mass storage (but maybe because of CWM and Magldr ??? I am not sure about this..) ..... when I connect SDCard adapter to one end of Y-Cable, it was not working... should blink the light but nothing happened (This is because of lack of power...) and of course HD7 did not recognize..
Funny thing is,
If connect direct to USB port of notebook, it blinking but connect to Y-cable, no blinking....
I didn't test other size of microSDCard so if someone tested, well it will be good information for other users instead of being crazy to find out "antique" 1G SDCard, I think....
After done, I checked Setting / About then I found out T-Mobile was gone.....
So my HD7 becomes unbranded now ?????
Then I flashed RSPL / HSPL without any problem and flashed straight for custom rom, NO PROBLEM !!!
Appreciate to ceesheim, viperbjk, xboxmod, ansar.ath.gr and other devs... who made my HD7 alive !!!!!
Thanks....
It worked perfectly with my Acer S100.....
You made me save money for me ~~
---------- Post added at 10:42 PM ---------- Previous post was at 10:39 PM ----------
Thanks....
It worked perfectly with my Acer S100.....
You made me save money for me ~~
My HTC HD7 (T-mobile) was initially bricked during an update.
Took it to a questionable phone repairer ..
Now you can start the phone, it goes to a red, blue and green screen with the following information:
PD29110 88-BC (4K)
SPL-1.16.2250.0(110866)
MicroP(LED) 0x07
TOUCH 81(v1.8,#1624)
Then it goes to a white screen with "Enter USB Host Mode.."
You connect it to the computer and it is not recognized via USB. Cannot turn the phone off using the on/off button.
Anyone know how can this be fixed?
NOTE: I am totally illiterate to phone tech talk so keep any answers to "very simple instructions". Thanks in advance :good:
Try flashing the device with a Tmobile Pre-NoDo/NoDo stock rom via the goldcard method and that should fix it.
Goldcard method - requires a Y cable, (either home made or purchased online) SD card reader and a 1gb to 2gb SD card (larger SD card can work but needs to be partitioned to 1gb) download the goldcard tool, goldcard image and the stock rom
Use this Tmobile rom -
https://rapidshare.com/#!download|4...02_Radio_5.65.09.25a_22.45.50.21U.7z|9315|0|0
Follow the goldcard tutorial and download the goldcard tool and image here -
http://forum.xda-developers.com/showthread.php?t=1597837
This process seems alot more complicated than what it really is...actually it's easy.
Download the goldcard tool and goldcard image and put them in a new folder on the desktop
Download the Tmobile rom and extract (use a program like 7Zip) it to a new folder on the desktop. Connect the SD card with the SDcard reader to the PC. Remove the Ruu_signed.nbh file from the rom and rename it to SCHUIMG.nbh (has to be capitalized) and put it on the 1gb - 2gb SD card (clean/wiped and formatted to FAT32)
Run the goldcard tool and press the Load goldcard image button and choose the goldcard image, the select patch MMC button.
Connect the SD card reader to the Y cable and connect it to the power source, put the device into "Enter USB Host Mode" and connect to the Y cable and the flash process should begin.
That's pretty much it. After the flash process the the device should be fixed and from there you can either connect it to your PC and update the device through Zune or you can install XSPL (RSPL/HSPL) and then flash a custom rom like one of the OS 7.8
If you need any help just let me know!
Loading ...
Thanks xdrc45, I really appreciate your assistance.
I managed to do everything you mentioned ... connected all up and the phone went from "Enter USB Host Mode.." to "Loading..." and then it just stays on that screen.
I left it on for over an hour and still no change. Any ideas?
Your welcome!
I had this same problem when I flashed mine with the goldcard method and I ended up using a different card reader and the flash process started immediately. Good thing is, it's recognizing the connection since it changed to "Loading" which means the Y cable is working.
Try some of these and see if they work -
1. Use a different card reader. If the card reader uses a USB cable (like a printer style USB cable) try a different cable.
2. Try switching around the connections to the Y cable.
3. Sometimes the camera button will get stuck in and prevent the device from flashing.
4. Make sure there are no other files on the SD card other than the SCHUIMG.nbh.
When the flash process doesn't start and it hangs on "Enter USB host mode or Loading" make sure to disconnect the device and pull the battery and re-enter USB host mode to start the process again.
Try these and let me know how it goes!
i have he same problem
hi
I have the same problem and I followed your steps and entered the usb host mode and it freezez in loading screen
as mentioned by you xdrc45 I removed the battery and re-entered the usb host mode stll its not moving further and stuck in Loading....
please help