HI dudes,
I'm actually in humeros 4.0.3 ICS on my Galaxy Tab P1000 but I'd like to go back to gingerbread 2.3.3, is this possible through Odin, do I need to re-partition ?
Thanks
alucard_xs said:
HI dudes,
I'm actually in humeros 4.0.3 ICS on my Galaxy Tab P1000 but I'd like to go back to gingerbread 2.3.3, is this possible through Odin, do I need to re-partition ?
Thanks
Click to expand...
Click to collapse
Yes it is possible.
You do need to insert PIT file i.e. need to re-partition. Not only that, you need to flash dbdata.rfs as well. I did this twice before.
Follow these steps carefully you should be fine:
1a. Get your 2.3.3 flashable file ready (.rar or .md5) -- you can find it in samfirmware.com if you don't have one yet.
1b. Download this pitfile from following link:
http://forum.xda-developers.com/attachment.php?attachmentid=631856&d=1308653969
1c. Download this dbdata from the following link:
http://forum.xda-developers.com/attachment.php?attachmentid=935230&d=1331091172
2. Start Odin - put the .md5 to PDA
Put the pitfile from step 1b to the PIT
Check re-partition. Leave everything else as is.
3. Go to download mode on the G-tab, connect to ur computer
and click start on Odin. It takes about 6 to 7 minutes to do the flashing.Once done flashing it will reboot but mostlikely you still have problems with your tab.
4. Reboot to download mode again. Reset Odin (make sure re-partition unchecked), put dbdata from step 1c to PDA, leave everything else as is. Reconnect your G-Tab to computer, click start on Odin.
5. When Dbdata is successfully put into your G-tab, reboot to recovery mode, do a factory reset wipe, and data cache wipe.
Reboot system, wait for about 5 minutes for the tab to boot up, you should be all set.
go back CM9,CM10,ICS from gingerbread
Hollo Guys,
i did the upgrade GT-P1000(gingerbread) to ics by cm9mod its come and run smoothly, but i lost my wifi,pakagedata connection,myfile option and most useful options are gone, so atlast i deside to to back original version, follow are the very useful and really work for me, if anybody bowing on cm9mod and go back original version, just click as follow.
yappoe said:
Yes it is possible.
You do need to insert PIT file i.e. need to re-partition. Not only that, you need to flash dbdata.rfs as well. I did this twice before.
Follow these steps carefully you should be fine:
1a. Get your 2.3.3 flashable file ready (.rar or .md5) -- you can find it in samfirmware.com if you don't have one yet.
1b. Download this pitfile from following link:
http://forum.xda-developers.com/attachment.php?attachmentid=631856&d=1308653969
1c. Download this dbdata from the following link:
http://forum.xda-developers.com/attachment.php?attachmentid=935230&d=1331091172
2. Start Odin - put the .md5 to PDA
Put the pitfile from step 1b to the PIT
Check re-partition. Leave everything else as is.
3. Go to download mode on the G-tab, connect to ur computer
and click start on Odin. It takes about 6 to 7 minutes to do the flashing.Once done flashing it will reboot but mostlikely you still have problems with your tab.
4. Reboot to download mode again. Reset Odin (make sure re-partition unchecked), put dbdata from step 1c to PDA, leave everything else as is. Reconnect your G-Tab to computer, click start on Odin.
5. When Dbdata is successfully put into your G-tab, reboot to recovery mode, do a factory reset wipe, and data cache wipe.
Reboot system, wait for about 5 minutes for the tab to boot up, you should be all set.
Click to expand...
Click to collapse
Related
On first boot I get
Can not mount / dev/block/stl10 (Invalid argument)
copy_dbdata_media: Can not mount DBDATE
Not Prepared your storage yet, please use UI menu for format and reboot actions
default copy content failed half
wiping / data cache and Does not Seem To fix anything.
Format sdcar unresponsive
HELP any occurrence and brick my phone
criskelo said:
On first boot I get
Can not mount / dev/block/stl10 (Invalid argument)
copy_dbdata_media: Can not mount DBDATE
Not Prepared your storage yet, please use UI menu for format and reboot actions
default copy content failed half
wiping / data cache and Does not Seem To fix anything.
Format sdcar unresponsive
HELP any occurrence and brick my phone
Click to expand...
Click to collapse
Go to Download Mode and flash ROM XWJM8 with pit512 and Re-Partition,after flash XXJPM with pit803 and without Re-Partition-this help
sardor said:
Go to Download Mode and flash ROM XWJM8 with pit512 and Re-Partition,after flash XXJPM with pit803 and without Re-Partition-this help
Click to expand...
Click to collapse
Fixed in a while I explain
My solution
With Odim 1.3, pit 512,
in my case JH2 I9000T GT
But for Europe JM8
Mark Re-partition, phone EFS clear and Phone bootloader Update
Then start
This process started well
JPM Process
Then uncheck re-partition, phone EFSclear and Phone Bootloader Update
JPM Pit 803 and firm JPM
Start
To enjoy
Thanks
criskelo said:
Then uncheck re-partition, phone EFSclear and Phone Bootloader Update
Click to expand...
Click to collapse
Is it normal for T model, or you just use weird and dangerous settings for fun?
Wiping EFS can lead to test-imei number and broken product code. Be sure you haver a backup of that folder before wiping that.
criskelo... I tried this and I didn't get anywhere :/
I had the same issue and it took me 2 hours to resolve (with a lot of pain, lol).
I've simply flashed the XWJM8 version using odin 1.3, no pit file and HENCE no repartition ticked.
It then booted to recovery console, because there was another error (can't remember which one cause I was too excited).
Anyway I did a wipe, cash clear and reformat SD card at the menu and let it boot.
After that I have flashed the latest version XXJPY also without PartitionInformation Table. (PIT). Then all the wipe and format stuff again.
I have now to go from scratch to setup anything again, but hey, at least my phone is alive again.
Some additional info. I also had that connection symbol on the screen with exclamation mark and triangle....so I thought I was done (due to trials with pit 512 which hung), but after removing battery and some trials I was able to enter download mode again....
Why happened that? I DON'T KNOW! I simply wanted to reflash the XXJPY stock rom, this time with pit512 and it lead to the topic of this thread!!!
This su**ed a lot, I didn't even modify something before!!!!
So: Less is even more! Don't fiddle with EFS and bootloader options it worked for me even without a pit!
Thanks to sardor for the initial idea, the XWJM8 seems to be a fixing rom for that when used properly, anyway to load a pit without to tick repartition is not a useful setting!
Well I was a long time reader at this great forum, IMHO the best regarding phone stuff, because there is the most useful knowledge shared.
I hope my first post will save other phones as well from sending it to repair.
Thanks I'm happy again..(let's see how long it'll last..lol...)
bricked my samsung galaxys and recoverd it
Hi I had exact same problem I totally bricked my i9000 Australian Optus version
I used
I9000DTJG4 firmware Australian Optus
With pit 512
And odin3 v1.3
Got all the files from
samfirmware . com / WEBPROTECT - i9000 . htm
Had to sign up but it’s free
However following criskelo's advice I unchecked the re partion box in odin
Even though the site above tells u to check it
And it worked
Thanks for everyone’s help on this thread.
Without you I would have had an expensive paper waited
Also the reason I got here in the first place as because I messed around with lag fix in clockwork recovery when I don’t know anything about it.
I was lucky this time but it’s really not worth playing around with things you doing understand.
sardor said:
Go to Download Mode and flash ROM XWJM8 with pit512 and Re-Partition,after flash XXJPM with pit803 and without Re-Partition-this help
Click to expand...
Click to collapse
I was messing with Darky's Rom which alway cause problems for me and found myself in the same situation as the first post.
What worked for me.
JM8 (2 files = code to PDA - Modem to PHONE) + Repartition + 512pit
after reset different error so goto download mode again then:
JPM + 803pit
Default OS reconfigures, Thank Fook
Awesome, thanks buddy! I have spent too much time trying to fix this phone and it all totally pays off now!
Here is the fix for the Bell firmware:
Background info: I orginally tried the Lagfix and bricked my phone, this is how I finally fixed it...
1. Using Odin v1.82
Put Phone in download mode
Use PDA: I9000UGJH2
Use Phone: Modem.bin
(both files came from samfirmware, I9000UGJH2 download)
Use: 512.pit(also from samfirmware at the bottom of the i9000 page)
Check Re-Partition, Auto-reboot, F. reset time, phone EFS clear and Phone bootloader update. I know everyone above says don't but I tried their way first and it didn't work, I would recommend you do try their way first and if no results try mine.
2. Using Odin v1.82
Put Phone in download mode
Use PDA: I9000UGJL2
Use 803.pit
Check only Auto-reboot, F. reset time
Good luck! I hope you do your happy dance like I did!!
crazycanuckeh said:
Awesome, thanks buddy! I have spent too much time trying to fix this phone and it all totally pays off now!
Here is the fix for the Bell firmware:
Background info: I orginally tried the Lagfix and bricked my phone, this is how I finally fixed it...
1. Using Odin v1.82
Put Phone in download mode
Use PDA: I9000UGJH2
Use Phone: Modem.bin
(both files came from samfirmware, I9000UGJH2 download)
Use: 512.pit(also from samfirmware at the bottom of the i9000 page)
Check Re-Partition, Auto-reboot, F. reset time, phone EFS clear and Phone bootloader update. I know everyone above says don't but I tried their way first and it didn't work, I would recommend you do try their way first and if no results try mine.
2. Using Odin v1.82
Put Phone in download mode
Use PDA: I9000UGJL2
Use 803.pit
Check only Auto-reboot, F. reset time
Good luck! I hope you do your happy dance like I did!!
Click to expand...
Click to collapse
hey how did it worked for you. Not working for me.
did you extracted the tar file? which file did you loaded into the pda tab then ?
Didnt worked for me at all
sardor said:
Go to Download Mode and flash ROM XWJM8 with pit512 and Re-Partition,after flash XXJPM with pit803 and without Re-Partition-this help
Click to expand...
Click to collapse
you saved my phone after me corrupting internal SD! just did my victory dance though hands still shaking a bit
Just thought I would add to what got my phone back running again after having the Can't mount DBDATA error. It's a bell I9000M.
Used Odin 1.3 , Flashed Darky's resurection per his instructions pulled battery once complete, went back into download mode and flashed stock JL2 with Odin , re-partition un-checked and no Pit file and after that my phone was running again.
You can find Darky's Resurection Here!
Can not find the link for the JL2 stock rom but it's in the general section somewhere.
the xxjpu version worked for me
tlick repartition
add 512 pit
tick and add pda
tick and add modem
tick and add csc
go to download mode
connect usb
press start
Need help with Fascinate
Hey guys, I've read the above posts but frankly it's above my skill.
Some how I ended up with the same message that the OP got.
Can someone walk me through the steps to completely fix my phone and get it back to bone stock?
I'm not familiar with PIT and other files. I need someone to hold me hand on this one...
cddt said:
I was messing with Darky's Rom which alway cause problems for me and found myself in the same situation as the first post.
What worked for me.
JM8 (2 files = code to PDA - Modem to PHONE) + Repartition + 512pit
after reset different error so goto download mode again then:
JPM + 803pit
Default OS reconfigures, Thank Fook
Click to expand...
Click to collapse
Was also messing around with darky. decided to go back to 9.5 for now. also got the error, then did what cddt said (thanks!!).
first flash - different error (something about CSC)
for second flash i used JS7 + 803pit + no repartitioning
worked flawlessly Thanks!
Stuck in boot loop
Samdroid_G_S said:
Just thought I would add to what got my phone back running again after having the Can't mount DBDATA error. It's a bell I9000M.
Used Odin 1.3 , Flashed Darky's resurection per his instructions pulled battery once complete, went back into download mode and flashed stock JL2 with Odin , re-partition un-checked and no Pit file and after that my phone was running again.
You can find Darky's Resurection Here!
Can not find the link for the JL2 stock rom but it's in the general section somewhere.
Click to expand...
Click to collapse
Hi,
I have bell sgs and I tried this and since then my phone is on boot loop. I can only go in download but not recovery. IT all started when I installed the boot loader for gingerbread...
Flashing Error - resolved
cddt said:
I was messing with Darky's Rom which alway cause problems for me and found myself in the same situation as the first post.
What worked for me.
JM8 (2 files = code to PDA - Modem to PHONE) + Repartition + 512pit
after reset different error so goto download mode again then:
JPM + 803pit
Default OS reconfigures, Thank Fook
Click to expand...
Click to collapse
Just followed this and it worked a treat thank you
Hi there,
I am having issues the same way. I am unable to do something. Can some explain me the procedure how to do it.
From where can i get the files.
Please help me out
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Dare{D}evil said:
hey..even i have a galaxy tab indian version...just follow the guides that are avaliable here for rooting flashing etc...etc...and i had the same modem when i bought it but its since been upgraded to a newer version of the modem so i just updated the modem to the ...DXJM2 version..thought the asian modem would be better for me..if u want i'll post the modem.bin
Click to expand...
Click to collapse
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
d) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
I really appreciated reply for my questions as it would allow me to move forward. I will ensure a good documentation at the end of the process for benefit of other users.
nchary05 said:
Thank you for quick reply. I started compiling the files need to flashing. So far, I could do following. Please advice me whether I am on the right path or not.
1. Rooted my tab with Z4root. Now I got root permission.
2. Downloaded Odin3 v1.7.exe and s1_odin_20100803.pit for flashing
3. Downloaded Roto-JMI-Full-v2.zip and Roto-JMI-Upgrade-v2.zip
Now, using Odin PDA button, I want to flash Roto-JMI-Full-v2.zip ?
Few questions:
a) Is this correct way of flashing or I am missing something?
b) Does above flash install Recovery also ?
c) which files need for PHONE and CSC files ?
MId) Which firmware best suitable for Indian Tab ?
Thank you in advance for clarifying above.
Click to expand...
Click to collapse
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Thank you.. I will do the same let you know the status....
blackheart2925 said:
Install Adfree or something which requires root acess for installation. Once rooted download something like root explorer from market which allows you to backup the modem.bin file. Or me or somebody else can just upload the file here.
Read the post/link in the thread where you downloaded Roto's JMI rom.
Use the .pit file from Roto's link not the thing which you posted...same place where you got the same ROM file. If you are flashing first time/from another rom then use the Full v2 zip file. Else use Update v2 when flashing from one of Roto's rom.
Connect the tab to your pc, reboot and go into download mode...press power+vol down button while rebooting...a yellow triangle icon with an android digging will come up...to get out of download mode,just keep the power button pressed till it rebooted normally.
Once in download mode, open up Odin and check that the yellow com box option is on. Check repartition option to ensure everything is wiped and you have a fresh install from scratch.
For PIT select the pit file downloaded from roto's link
For PDA select the Full.tar file
For PHONE select the modem.bin file
For CSC leave it blank...
Once done, recheck and hit start.
PLEASE CHECK ROTO'S JMI V2 THREAD IN THE DEVELOPEMENT SECTION...it has a link to howto which is old but gives some idea of how to proceed...for pit, pda, phone follow as I suggested and things will go fine...
Sent from my GT-P1000 using XDA App
Click to expand...
Click to collapse
I followed the steps after flashing 'full' tar, it rebooted tab, started the normally. After that, I verified that, all applications , phone (GSM) and wifi working fine.
Now my question is do I really need to flash *second* tar file ? what is it for ?
^^No. It is only for people upgrading from previous versions! You are good to go!
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Can you get into download mode? If yes then you should be able to flash...but I would suggest checking"I bricked my tab" threads in general or developement section...
Sent from my GT-P1000 using XDA App
nchary05 said:
Now, I want to install CWM recovery. Please some one can confirm below steps:
1. Make sure to have Samsung Kies installed, and your tab at least connected once, to be sure the drivers are correct.
2. Your Tab must be Rooted.
3. If you wish to do a backup, now is the time.
4. You will need an SD Card with enough free space for the filesystem conversion, and to put the Overcome ROM on before we start. (An empty 4gb should be plenty, as long as it is empty, or close too)
5. Download and Extract the following file to your computer: http://www.apksmash.com/corodius/galaxytab.zip (Contains "Odin3 v.1.7.exe" "Overcome_Kernel_v1.0")
Now, we will Install the Kernel and perform the EXT4 filesystem conversion.
1. Turn off your Galaxy Tab.
2. Turn your Galaxy Tab on into DOWNLOAD mode (Press Volume DOWN and Power On at the same time).
3. Open Odin3 v1.7.exe on your PC.
4. Connect your Galaxy Tab to your PC via the USB cable.
5. Make Sure the ID:COM box is highlighted yellow (meaning it sees your tab).
6. Click on the PDA button and select the Overcome_Kernel_v1.0.tar file you downloaded earlier (make sure PDA is ticked after selecting the file).
7. The only boxes ticked should be:
A. Auto Reboot
B. F. Reset Time
C. The PDA tickbox
8. Click start and wait for PASS! to show highlighted green on Odin.
9. Your Galaxy Tab will Reboot, and get stuck on the Samsung Boot Screen. This is fine.
10. Turn your Galaxy Tab off by holding the power button for about 5 seconds.
11. Turn your Galaxy Tab on into RECOVERY mode (Press Volume UP and Power On at the same time).
12. The Galaxy Tab will now perform the EXT4 conversion.
13. Sit tight, depending on how much data you have, this can take quite a long time.
14. Once finished, click reboot system now (by pressing the power button).
At this point, You have installed the Overcome Kernel with CWM included and converted the Filesystem to EXT4. It has been reported that many stock ROMs will boot and run fine now, however some may not, but it just depends on your ROM etc.
http://forum.xda-developers.com/showthread.php?p=11713685.
Would be there any problem ? or is there any easy way to install CWM Recovery.
Click to expand...
Click to collapse
I followed above steps and could able to install CWM RECOVER.
congrats dude
maddy_in65 said:
I had bricked my tab while modding battery icon and it was not booting now. Now i want to flash with the custom rom available here. I am noob to flashing so just want to confirm the steps mentioned above applicable to the bricked tab. Can somebody guide me for bircked tab.
Please mentioned the good custom rom with Ext4 conversion at the time of install. I am using indian tab.
@OP:- Sorry for hijacking this thread but find some info here for my queries
Click to expand...
Click to collapse
can you just tel me which modem.bin are u using coz i was planning to flash but stuck on decision bcoz of modem... is it jpz or jk3? or any other
A new GB version is available DDJPA
http://forum.xda-developers.com/showthread.php?t=1226674
need PDA PIT PHONE CSC files
Kindly send me the links for downloading the PDA PIT PHONE CSC files as I could find only broken links.
My samsung tab (Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)) is bricked and won't boot.
Than You
nchary05 said:
Could some one for benefit of Indian Tab Owners, write a step-by-step instructions or guide. Lot of information to digest for a new user including details of 1) rooting 2) installing recovery 3) flashing ... this information would be great useful for everyone.
My Tab details :
(Model: GT-P1000 | Code: INU | Version: P1000DDJK3/P1000ODDJJ1/P1000DDJJ1)
Click to expand...
Click to collapse
After installing the lastest "S.U.R.F.A.C.E" ROM on my GT-I9000 I'm presented with the Galaxy S logo and nothing else,
Tried and tried vol up + home + power number of times now with no avail.
Everything was working fine before was able to boot into clockwork recovery ect, unfortunately I do not have a usb cable so can't try odin any help would be great.
Grab yourself a jig from ebay or the likes, or make one
http://forum.xda-developers.com/showthread.php?t=819551
It will boot into download fine the problem I have is it won't boot into recovery is there any way I can wipe it or does it look like I am in need of a cable?
Then reflash back to stock using Odin
What were you flashing from as surface is an oxeded rom, not dexeded.
buttwad said:
What were you flashing from as surface is an oxeded rom, not dexeded.
Click to expand...
Click to collapse
clockwork recovery, i take it I messed up here so
No, meant what rom were you on before your flash? Stock?
oh sorry got the phone of a friend looked like a custom samsung rom, build version was easyprojectv2 if that rings any bells?
Looks like the problem was caused by trying to flash a odexed rom over a deodexed rom, or not having the correct bootloaders for the new rom. Normally before a flash I would return to stock (firmware from sammobiles.com) first via ODIN, do all the wipes, flash a kernel so you have a nice clean install to 'abuse'. Then I would add any custom rom from there be it by ODIN or by cwm.
Grab yourself a usb lead, nice clean flash and start again.
Ok so I've 3 file here:
APBOOT_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
CODE_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
KERNEL_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
s1_odin_20100803.pit (not sure if i need this as was in the root of the odin folder not the firmware?)
Where do the other 3 file go PDA PHONE CSC???
I am also stuck on the same front, i donwloaded rom from samfirmware but it only had PDA part and nothing else, please suggest which official rom should i download??
stevek93 said:
Ok so I've 3 file here:
APBOOT_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
CODE_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
KERNEL_I9000XWJW1_CL788890_REV03_user_low_ship.tar.md5
s1_odin_20100803.pit (not sure if i need this as was in the root of the odin folder not the firmware?)
Where do the other 3 file go PDA PHONE CSC???
Click to expand...
Click to collapse
I would go this way mate, first grab JVT from sammobiles.com ( register first)
Flash that using ODIN
Comes with 3 files, CSC, PHONE and PDA
PDA file goes to PDA in ODIN
PHONE goes into MODEM in ODIN
CSC goes in CSC in ODIN.
Also select PIT file, should be 512 on the PIT section on ODIN, hit start and it will flash then reboot.
Then open ODIN again, connect phone and flash your KERNEL to the PDA section of ODIN.
Then grab this http://forum.xda-developers.com/showthread.php?t=1117579
and flash using cwm.
Your then on JW1 all rooted and ready to play.
put the "APBOOT_I9000XWJW1_CL788890_REV03_user_low_ship.tar" file into the PDA and flashed it. Everything seems to be working fine might stick with the stock for a while never really needed to be rooted.
ok i just popped the SIM and have no network access when i tap on Mobile Networks in the setting it tells me to insert a SIM????
the firmware i had was wrong didnt have a modem. Downloaded a jvt as buttwad said flashed an now everything working perfect now. cheers mate!
CM9 nice but not ready .... ok, because I'm a noob I have a big problem. I have my new SGS (i9000 3.2.3firmware) with cf-root 2.6 from here (*http://forum.xda-developers.com/showthread.php?t=788108*). Yesterday put CM9 on it from here (http://forum.xda-developers.com/showthread.php?t=1363593) .. and this morning I do not like it..*so I open cwm and tap to restore from backup ... now my galaxy wont open again... what can i do now??
and odin can see my phone in download mode....
sorry for my bad english, i can speek only greek and german...
did you have a backup to begin with?
if odin can see your phone in download then just flash another rom
It doesn't work because the stock partitions are different to CM9. Flash a stock version of whatever you had before in odin with repartition, then a kernel. Then you should be able to restore your backup from CWM
As posted above. The partitions between CM & stock are different. I did exactly what you did. With the same result.
You can get a stock rom from here: http://www.sammobile.com/firmware/
Once you have a stock rom you need to use Odin to install it. You will need to have all three files & the pit file. (phone, modem, csc, pit - 512).
Make sure Kies is not running & open Odin. Click re-Partition. Click PIT & select your pit file, Click PDA & select file with PDA in name, click phone select file with phone in name, click CSS & select file with CSC in name.
Once you are ready with this start phone in download mode. Once in download mode attach phone to usb cable wait for top left corner to go green & click start.
This can take some time but once complete phone should restart. At this point my phone got stuck (either boot loop or black screen I can't remember)
If this happens don't panic just remove phone from USB & restart odin. Now make sure re-partition is unchecked & select the three previous files again, don't select pit file. Again put phone in download mode (you may need to pull battery first) wait for Odin to be ready & click start. This time when the phone reboots it should start although this can take a little longer than usual.
Once started I always like to reboot a couple times & clear cache & do factory reset in recovery.
I want to go back to gingerbread am rinning Dark Knight rom any help plz
Why God .. why ...
Flash stock through ODIN or Heimdall and thats it
If you had to ask this, it's probably a good thing you're going back to stock.
Sent from my Telus Fascinate running OneCosmics ICS!
why would you say that
Get stock ROM here.
http://www.sammobile.com/firmware/?page=3&t=1&o=1&m=GT-I9000&r=-1#modelsa
You need stock ROM (3 file stock ROM), Odin & Pit512.
1. Start ODIN.
2. Select the files into the relevant places in ODIN.
3. Click repartition.
4. Put phone into download mode.
5. Connect phone to pc.
6. wait for Odin to connect to phone.
7. click start.
8. wait for ODIN to finish & for phone to reboot.
You must have pit512 and click repartition as ICS uses a different file system to Gingerbread.
You may have a boot loop after doing this. I have had this occasionally. To solve this reflash with ODIN. This time make sure repartition is unchecked and don't flash pit file.
Sorry Screen shot says scs. I meant CSC.