Related
DID I JUST BRICK MY PHONE??
tried flashing the i9000 rom... got messed up sometime after flashing csc and pda.... now i can boot to recovery menu and get odin to recognize but im getting an error
copy_multi_carrier from: ATT
multicsc : can not acces to /system/csc/ATT/system/
copy_common_data
then it stalls.. my power button doesnt work to reboot system now...
Even though odin recognizes i hit start and nothing happens..
can anyone help.. i will donate and make it worth your time..
No you didn't brick your phone, you need to follow the I9000 guide in the stickied threads. You need to load a Captivate kernel before fully rebooting your phone.
First off get your phone back into download mode. Pull battery and usb cable, restart Odin, then follow this method to get you into download mode, put in battery, hold down both volume buttons, keep holding them and plug in the USB cable.
First when you flash a I9000 rom make sure you uncheck autoreboot on Odin.
When this done when you flash the Rom it will say Restet in Odin. At that time pull your battery and USB cable.
Restart Odin and load the Captivate kernel. Put you battery in, hold both volume buttons, keep them held and plug in the USB cable, should go into download mode. Start Odin, and it should be fine to let it autoreboot.
I missed something it will be in the stickied thread.
Sent from my SAMSUNG-SGH-I897 using XDA App
can you clear something up is Android System Recovery the same as download mode??
ok this thread can be deleted.. im a noob.. kjpdx throw me a link to donate.. i figured it out by myself but atleast you replied..
Two different modes. Download mode shows an Android holding a shovel and Recovery mode is where you would install update.zips.
Needs to be in Download mode when installing roms and kernels with Odin.
Sent from my SAMSUNG-SGH-I897 using XDA App
Dont worry about it, glad i could help.
Sent from my SAMSUNG-SGH-I897 using XDA App
Hi:
I have the same problem of my Galaxy S. It is stuck in this screen saying
copy_multi_carrier from: ATT
multicsc : can not access to /system/csc/ATT/system/
etc. etc.
I boot it to the download mode as instruction, but the Kies always shows connecting device, and it never gets connected. The Odin shows no com port or device for me to load the firmware. Can anyone help? Any help will be appreciated.
uehsgerg said:
Hi:
I have the same problem of my Galaxy S. It is stuck in this screen saying
copy_multi_carrier from: ATT
multicsc : can not access to /system/csc/ATT/system/
etc. etc.
I boot it to the download mode as instruction, but the Kies always shows connecting device, and it never gets connected. The Odin shows no com port or device for me to load the firmware. Can anyone help? Any help will be appreciated.
Click to expand...
Click to collapse
You can't have Kies and Odin running at the same time =P
^lol that solved my problem too! thanks!
Zilch25 said:
You can't have Kies and Odin running at the same time =P
Click to expand...
Click to collapse
Will try it later. Thanks
It is fixed. Thank you for the help. I just need to lauch Odin first prior to plug-in my phone. Now, I don't have bricked Galaxy anymore. Thanks
KJPDX said:
No you didn't brick your phone, you need to follow the I9000 guide in the stickied threads. You need to load a Captivate kernel before fully rebooting your phone.
First off get your phone back into download mode. Pull battery and usb cable, restart Odin, then follow this method to get you into download mode, put in battery, hold down both volume buttons, keep holding them and plug in the USB cable.
First when you flash a I9000 rom make sure you uncheck autoreboot on Odin.
When this done when you flash the Rom it will say Restet in Odin. At that time pull your battery and USB cable.
Restart Odin and load the Captivate kernel. Put you battery in, hold both volume buttons, keep them held and plug in the USB cable, should go into download mode. Start Odin, and it should be fine to let it autoreboot.
I missed something it will be in the stickied thread.
Sent from my SAMSUNG-SGH-I897 using XDA App
Click to expand...
Click to collapse
Thanks! I couldn't get download mode and this is the only thread online to help. I received this error when trying to install the voodoo lagfix while running cognition 2.2 beta 7. (for some reason, my cognition did not have the lagfix built in)
cliffgardner said:
Thanks! I couldn't get download mode and this is the only thread online to help. I received this error when trying to install the voodoo lagfix while running cognition 2.2 beta 7. (for some reason, my cognition did not have the lagfix built in)
Click to expand...
Click to collapse
That reason is that voodoo doesn't work with 2.2
For the sake of your wallet, I would read the threads more carefully before flashing new roms if I were you. I'm not trying to be a ****, but this issue was addressed many times in the cognition thread. I'm all for learning from others on this forum after they make the mistakes
Hello,
I have flashed my Galaxy Tab with roto JMI, but it's stuck at the "GalaxyTab / Samsung" boot screen.
I can get into download mode with volume down and power, I can reflash it but in the end it does not boot.
What can i do?
loony
*bump* anybody?
Help please!!! I have the same problem!
I am still having this problem. I am wondering if there is any way how to debug whats happening at the Samsung logo screen. With adb the devices is not detected (it seems not to be detected at the usb controller).
What did you use to flash?
What files did you use?
Give all the info so people can help
Sent from my GT-P1000 using Tapatalk
Hi, I have exactly the same problem.
After upgrade du JMI roto with odin 1.7 (all upload seems to be ok, repartition with p1 and pda file Roto-JMI-Full-v2 no error message) but the device hangs on samsung galaxy tab logo and don't boot.
In my case previous version was pda jj3/phone jid / scs jj2
rsmurdoch said:
What did you use to flash?
What files did you use?
Give all the info so people can help
Sent from my GT-P1000 using Tapatalk
Click to expand...
Click to collapse
Device it GT-P1000 (German/European version)
Bought the device
Got a lot of restarts
Flashed with P1000OXAJM6
Device worked again for some days
Device not booting anymore
Tried reset with different methods (Touch screen, press power; Touch menu button and power button): Sometimes worked, sometimes not
Recently not booting anymore, no trick worked
Flashed Roto Roto-JMI-Full-v2.tar with P1_add_hidden.pit
Device still not starting
Flashed original firmware: GT-P1000_P1000XXJK5_P1000OXAJK5_P1000XXJK5_P1000XXJK5_XX_DBT.zip
Device not starting
Flashed ROTO with Heimdall again (before used Odin only): Device not booting
Thanks!
Same Problem
Im on the SPH-P100, I have the same issue I can access it in Adb the log shows it in stalling all of my old .apks but it never boots past the logo.I have re flashed also but no luck plz help if u can i can post the logcat here but it goes for hrs -_- I assume it loops the process.
loonyt said:
Device it GT-P1000 (German/European version)
Flashed with P1000OXAJM6
Click to expand...
Click to collapse
So, this one contains a bootloader (Sbl.bin). maybe thats the cause of the problem. Still, I wonder why it started in the first place and then after some reboots it gets stuck. I tried different Kernels with no luck. Maybe I should try to flash a new bootloader? However, that could brick the device forever.
Loonyt
loonyt said:
Device it GT-P1000 (German/European version)
Bought the device
Got a lot of restarts
Flashed with P1000OXAJM6
Device worked again for some days
Device not booting anymore
Tried reset with different methods (Touch screen, press power; Touch menu button and power button): Sometimes worked, sometimes not
Recently not booting anymore, no trick worked
Flashed Roto Roto-JMI-Full-v2.tar with P1_add_hidden.pit
Device still not starting
Flashed original firmware: GT-P1000_P1000XXJK5_P1000OXAJK5_P1000XXJK5_P1000XXJK5_XX_DBT.zip
Device not starting
Flashed ROTO with Heimdall again (before used Odin only): Device not booting
Thanks!
Click to expand...
Click to collapse
*bump* Can anybody help?
I have a very similar problem.
I flashed the [ROM] Roto JMI Pre-Rooted Firmware v2 [Feb 4, 2011], and got stuck on the Samsung Boot screen.
Now, I can't even get the Downloading mode to work. It opens fine, but Odin/Heimdall doessn't detect the Tab at all.
Hopefully, someone knows what's going on. If not, I'm taking it back to my carrier, and asking them to fix it (assuming they'll fix it).
Maybe this will help for the bootloader.
Its a bootloader patch. Please read thru the thread. Hope it helps.
http://forum.xda-developers.com/showthread.php?t=888071
Sent from my GT-P1000 using Tapatalk
dlui1 said:
Now, I can't even get the Downloading mode to work. It opens fine, but Odin/Heimdall doessn't detect the Tab at all.
Click to expand...
Click to collapse
Dont get what you mean by that. You cant get it to download mode but your tab start up fine?
Download mode = press vol down + power pn button.
As for odin/heimdall doesnt detect the tab it could be usb port (some reports in android development thread) or could be usb drivers.
As i need to switch usb drivers when i need to flash my tab & my dell streak.
Hope it helps to start you off.
Sent from my GT-P1000 using Tapatalk
Qsilver2001 said:
Dont get what you mean by that. You cant get it to download mode but your tab start up fine?
Download mode = press vol down + power pn button.
As for odin/heimdall doesnt detect the tab it could be usb port (some reports in android development thread) or could be usb drivers.
As i need to switch usb drivers when i need to flash my tab & my dell streak.
Hope it helps to start you off.
Sent from my GT-P1000 using Tapatalk
Click to expand...
Click to collapse
I meant that I can get into Download mode, with the Downloading logo, but doesn't get detected by Odin. And it stays stuck on the Samsung boot logo if turned on normally. Can't get into recovery either.
Before I flashed the Roto ROM, Odin was working perfectly fine. I've been flashing other kernels and ROMs before. But now, the USB doesn't even seem to get detected. It's like nothing is plugged in. Can't even choose to install/uninstall old/new drivers.
I dont think it's the USB port, as I've tried to connect to Odin on 3 different computers, trying every available port on each. It's looking like the USB connector is just dead or something.
My tabs mainboard was broken, it was replaced and now it works again.
Sent from my GT-P1000 using XDA App
Same problem here man. I CAN get in to download mode. Odin recognize it normally. I CAN download normally. Look likes everything is normal, but after update it restarts, but hangs on Galaxy Tab Samsung logo. I've tryed everything with different firmware, custom-roms, hacking things, but with no success.
Can someone please help me?
Same problem here. My tab is stuck at samsung galaxy logo and until now, no one could provide an answer.
I flashed some ROM from samfirmware that must of locked the bootloader (JMF). Then I tried to flash JM6, JMA, JMC, JMK, JJ4, JJ7, JM5, JJ1, JID and almost all ROTO's. with and without pit files using ODIN 1.7. I also tried a stock ROGERS ROM (that i downloaded from this forum) using Heimdall. The tab always boots to samsung galaxy tab logo. I've done alot of reading in this forum and followed many flashing instructions but when applied, it doesn't work for me.
My main concern: is there still hope with the tab ? or it's gone forever.
Is there any specific order that i must follow when flashing ? ( ie, flash one specific ROM before another). The tab was canadian that was flashed to euro.
Thanks for reading my post.
the dbdata file is corrupted.
1) download this file
http://forum.xda-dev...98&d=1290261479
2) extract it
3) use Odin to flash it under the PDA option
-make sure repartition is UNCHECKED
-do not select any pit file
-leave everything else the same
handfree said:
the dbdata file is corrupted.
1) download this file
http://forum.xda-dev...98&d=1290261479
2) extract it
3) use Odin to flash it under the PDA option
-make sure repartition is UNCHECKED
-do not select any pit file
-leave everything else the same
Click to expand...
Click to collapse
Same prob. tab reboots to samsung logo.
Same Here, I tried many combinations with the help of experts on this board. Conclusion: shipped to Sammy for warranty repair.
Totally bricked it.
- Unable to boot into recovery.
- ODIN doesn't detect my phone. (possible USB brick?)
- Screen stays stuck at SAMSUNG GALAXY S
Was trying to re-flash CM7, wiped data, reboot, doesn't work.
Tried booting back into recovery, no longer works.
Anyone has any idea? Bootable SD card doesn't work too.
I'm totally out of ideas.
mate did u try to go to download mode???
Download mode flash stock rom with pit 512 and repartition ticked ..
No download mode recovery jig of front page .
jje
how do i do it if ODIN doesn't read my phone anymore?
if you don't go into download mode; odin will not recognize your phone. otherwise, if you can't access download mode, you must use a JIG made of resistors. search the forum. or, if odin fails to detect your phone again, you must clean the contacts of the cable and the phone and the pc. again search the forum. if this fails, try a different cable or a different computer. and make sure that you have the necessary usb drivers installed.
Managed to restore my phone! THANKS A LOT!
Hi everyone! I have Captivate(1008 batch) with Phoenix Ultimate firmware. Today I tried to flash it with batch Gingerbread. Seems like my mistake was that I forgot to turn off lagfix. Odin halted. Now I'm getting "phone-!-PC" screen each time I connect phone to PC...
I can not get cappy into download mobe(tried all 3 ways)
Odin doesn't see phone...
Do I have any chaces to repair my phone or it's a brick? Is there a chance that jig will help?
There's a new thread in the dev section about a one click unbrick from that screen. I read that it's just downlad the software, plug in phone and click run.
AdamOutler made this -
http://forum.xda-developers.com/showthread.php?t=1153310
Ok, thanks I'll try that! BTW which fimware should I flash if my cappy is back to download mode? As I understand Phoenix formated my phone memory into ext4 filesystem. Is that possible to flash stock Gingerbread on ext4 filesystem?
UPD: Unfortunately software unbrick doesn't help I got "Phone is not connected" message. My PC doesn't see phone at all
The Jig should work, assuming you don't have mixed bootloaders. If you do have mixed bootloaders, JTAG service will be what you need.
If you do manage to get back to download mode, use the JF6 Odin 1-click.
You can get it here: http://forum.xda-developers.com/showthread.php?t=731989
Here's another suggestion that I did with a 1008 that I had a while back. open Odin 1 click to prepare for download mode. (make sure it's not one with the three button fix - if you one click from gingerbread to 3 button fix stock, it is a certain hard brick).
Remove battery, count to 10, replace battery.
hold the vol up and vol down buttons at the same time until you see the screen flash. It should flash every 5-7 seconds as long as you continiuosly hold the buttons.
When you see the screen flash, insert usb cord (with it already connected to computer).
This got me to download mode. It mat take a few tries. sometimes it's a challenge to get to DL mode from this screen. This procedure worked on my 1008. Hope it works.
A jig may work too, but it n ever worked for me on the 1008.
Thank you guys. Hope your suggestions will help!
With the phone and PC screen the Jig will work for sure try and make one or u can buy it.
You can also try this, Remove the battery open odin 1 cick and plug the cable to the usb port at the back of the PC and then the phone and now put the battery see if the odin lits up if yes you are done.
I solved the problem(even without jig). So writing my solution, hope this will help someone.
1) I went home to use another PC. Installed Samsung drivers there.
2) I tried different key combos. Vol Up + Vol Down didn't worked but Vol Down + USB entered Download mode.
3) One guy from russian android forum told me to try with Odin 1 click 2.1 stock firmware. Only this version of firmware connected to my soft bricked phone.
One more time thanks everyone for your replies
For future reference.
If your phone turns on (you can see anything on the screen), then you do not have a perminate brick, and a jig will work.
And your filesystem/lagfix does not matter with odin 1click. It resets everything to the way it came, nomater what you came from. (It even works on cm7 witch repartisioned it and used MTD).
I have the same problem as you. I can't get get the one-click unbrick to work (doesn't detect a device). I ordered a jig yesterday, hopefully it comes soon. I have a 1010 though, which I heard had more problems than others.
use a JIG
i made my custom JIG for 60 cents, save my Cappy after a failed cyanogen install.
I followed instructions on a link via the cyanogenmod website, to try and get cm7 on my phone. The instructions were on a wiki website which I now know is not reliable!
I got to the stage "flashing cyanagonmod" to find out that the zip files had to be in the internal sd card BEFORE starting the whole process!
I can still access download mode and recovery. But my phone gets stuck on the "Samsung galaxy i9000" intro screen.
I tried restoring and factory reset but still no joy...
any help is very appreciated!
Download some odin flashable ROM, and flash that in download mode.
where do I find an odin ROM and how do I know which one to use?
corrected: samfirmware.com
If you want a custom rom, then look through here however your going to have to read which is odin flashable...
This is a guide and rom i have used myself. Click here
BTW this is obviously assuming you are on SGS I9000 the second link should be quite clear...
here's a nice link to finding stock firmwares and using Odin:
http://forum.xda-developers.com/showthread.php?t=1102881
Talon26 said:
samsungfirmware.com
If you want a custom rom, then look through here however your going to have to read which is odin flashable...
This is a guide and rom i have used myself. Click here
BTW this is obviously assuming you are on SGS I9000 the second link should be quite clear...
Click to expand...
Click to collapse
Thanks for your post. Only problem is ODin doesn't recognise when my phone is plugged in? i.e. there isn't that yellow box showing...help!
Ok so im guessing your trying the 3 button combo for download mode (vol up + home + power). Alternatives to force download is a homemade jig, which is easily obtainable from ebay for a relatively cheap price. Other ways you can try is holding the combo for as long as you can, some have reported it may even work after 3 mins. Another method is hold the combo and then whilst holding it insert the battery. Also the last method but have the usb plugged into with odin open, then put the battery in. Many many ways... just search
Is that what you mean or that you CAN get to download mode and Odin and the computer does NOT recognise when you plug it in. If this is try re-installing the drivers using kies, its under the tools menu. Try a different version of odin, plug phone in then try the combo (with battery already in, then without). Have you closed all Kies applications background processes? (use task manager in windows). Use another computer..
Also have you read this
Edit: Forgot to add, can you get into Recovery? Then use your nandroid backup which you should always do before flashing.. If you dont have a back up try use ADB to force download mode "adb reboot download"
Need to know what options you have available in-order to help, what can you do? Is there any response from your phone with pressing buttons or key combinations??