Hello!
I've been flashing stock ROM for my ACE via ODIN. then I had a cut. hopefully the phone can get in download mode. but when i start normally there's a message of phone with a yellow sign trying to connect to computer. ODIN is STUCK with this message:
<1> START!!!
<1> set download environment.
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> mibib download..
PLEASE HELP ASAP! because one can not live without his ACE !
Samadony said:
Hello!
I've been flashing stock ROM for my ACE via ODIN. then I had a cut. hopefully the phone can get in download mode. but when i start normally there's a message of phone with a yellow sign trying to connect to computer. ODIN is STUCK with this message:
<1> START!!!
<1> set download environment.
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> mibib download..
PLEASE HELP ASAP! because one can not live without his ACE !
Click to expand...
Click to collapse
Try doing to Download Mode combo.. (Vol- Home Power) then hit start.
Luckier than me, the stock ROM I flashed through Ace had a corrupt boot.img- happy hard brick
So i press vol down & home & power! that's what i;ve been doing.
did you solve it ?
a yellow exclamation mark between a pc and phone icon is it?
try this.
take off battery, let the phone stay for around 10 seconds, press the three button combination for download mode (the home+vol down+power) and while u still holding those three button reinsert the battery. now device should go into download mode and u can properly flash with odin.
an0nym0us_ said:
a yellow exclamation mark between a pc and phone icon is it?
try this.
take off battery, let the phone stay for around 10 seconds, press the three button combination for download mode (the home+vol down+power) and while u still holding those three button reinsert the battery. now device should go into download mode and u can properly flash with odin.
Click to expand...
Click to collapse
Yes it's YELLOW mark.
I'll give it a try now, Hope it works because i really need to use it since I've an emergency.
EDIT: SAME stuck in mibib download, what's the mibib download??
crap.. forgot to mention.. while u do it, it shouldnt be connected to pc. only connect it to pc after it had succesfully go into download mode.
---------- Post added at 11:37 PM ---------- Previous post was at 11:32 PM ----------
Samadony said:
Yes it's YELLOW mark.
I'll give it a try now, Hope it works because i really need to use it since I've an emergency.
EDIT: SAME stuck in mibib download, what's the mibib download??
Click to expand...
Click to collapse
did u manage to force it into download mode by the step i said earlier?
flashing the phone while its still showing the error exclamation screen wont work.
an0nym0us_ said:
crap.. forgot to mention.. while u do it, it shouldnt be connected to pc. only connect it to pc after it had succesfully go into download mode.
Click to expand...
Click to collapse
Have you tried this sucessfully before? ..
trying one more time. thanks for ur help.
Samadony said:
Have you tried this sucessfully before? ..
trying one more time. thanks for ur help.
Click to expand...
Click to collapse
yes, i've got the same error exclamation screen before and i did personally test the force into download mode trick
I downloaded another stock rom to see if it's not from the other Stock i'm flashing but the one i'm flashing i'm sure 100% it's working...the new one have 3 .tar.md5 files here's the names:
APBOOT_S5830JPKP9_CL457554_REV03_user_low_true.tar.md5
CODE_S5830JPKP9_CL457554_REV03_user_low_true.tar.md5
GT-S5830-MULTI-CSC-OJPKP3.tar.md5
1. this isnot a one package stock?
2. shall i try another ODIN version
3. shall this be due to the OPS file?
an0nym0us_ said:
yes, i've got the same error exclamation screen before and i did personally test the force into download mode trick
Click to expand...
Click to collapse
Would you link me the stock you've flashed?
ughh u havent answered my earlier question yet. did u manage to force it into download mode by the step i instructed?
it doesnt matter which rom u download, which odin version u try, it wont work while its still showing the exclamation error screen.
an0nym0us_ said:
crap.. forgot to mention.. while u do it, it shouldnt be connected to pc. only connect it to pc after it had succesfully go into download mode.
---------- Post added at 11:37 PM ---------- Previous post was at 11:32 PM ----------
did u manage to force it into download mode by the step i said earlier?
flashing the phone while its still showing the error exclamation screen wont work.
Click to expand...
Click to collapse
Yes i did manage to force it into download mode, but still stuck in ODIN ! Crap. trying again and re informing you.
now the exclamation error solved, proceed with odin.
usually the stuck in odin caused by kies running in background. open windows task manager and kill kies process. and then open odin with administrator priviledge.
if its still doesnt work try on other pc.
an0nym0us_ said:
ughh u havent answered my earlier question yet. did u manage to force it into download mode by the step i instructed?
it doesnt matter which rom u download, which odin version u try, it wont work while its still showing the exclamation error screen.
Click to expand...
Click to collapse
1. i press the Vol down + home + power with no battery,
2. insert the battery while pressing
3. it automatically shows no screen but the downloading mode. (so i forced it to download)
4. i connect the cable to laptop
5. flash using odin, and still getting "mbib download..."
an0nym0us_ said:
now the exclamation error solved, proceed with odin.
usually the stuck in odin caused by kies running in background. open windows task manager and kill kies process. and then open odin with administrator priviledge.
if its still doesnt work try on other pc.
Click to expand...
Click to collapse
I've been trying this with no Kies, no SIM card and no SD-card.
trying on another laptop.
btw if your in windows vista or 7, disable windows uac control. that too can cause odin problem.
and u mention that u try without kies installed. make sure u had samsung's usb driver installed.
an0nym0us_ said:
btw if your in windows vista or 7, disable windows uac control. that too can cause odin problem.
and u mention that u try without kies installed. make sure u had samsung's usb driver installed.
Click to expand...
Click to collapse
ODIN reads my phone, i think then i have the USB Driver. I'm trying on another laptop now. hope it works.
an0nym0us_ said:
btw if your in windows vista or 7, disable windows uac control. that too can cause odin problem.
and u mention that u try without kies installed. make sure u had samsung's usb driver installed.
Click to expand...
Click to collapse
1. forced download
2. UAC is disabled
3. no kies
4. don't konw about Samsung USB driver if installed or no, but searching for that
5. it's been 5 mins and says mbib crap download.
what's wrong!??
EDIT: used ODIN as adminstrator, now it's stuck with setup connection? is that a driver issue?
u mention that odin can detect the phone, that proves u already had the driver installed.
but in case u want it, here u go. the standalone usb driver without kies crap.
https://hotfile.com/dl/141204140/576b45c/SAMSUNG_Mobile_Phones_USB_Driver.rar.html
and if the archive ask for password, its
Code:
samfirmware.com
Now I've made what you said, carefully. still Stuck in ODIN:
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
<1> START!!!
<1> set download environment.
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> mibib download.. << freeze here
Related
HELLP!! i am trying to update my moms S Plus I9001 to a newer Nordic version (i9001xxkqg) using Odin (Multi Downloader v4.43) and it stops on AMSS.mbn!! How do i fix this! i am on my cabin now with only one PC. so do you have a any idea???
Here is what Odin says.
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
<1> START!!!
<1> set download environment.
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> amss.mbn download..
(After 100 minutes)
I have tried many Odin versions but, only 4.43 works with (I9001 S Plus) And i have put the AriesVe.Ops in the Ops place and the Firmware in the One Package. And now my phone displays a yellow triangle and i cant turn it on!! plzzz help!! Plzzz!
I guess my phone is bricked.
Plzzz, help me.
Eirik2306 said:
Plzzz, help me.
Click to expand...
Click to collapse
1) remove battery and reinsert
2) go into download mode
3) ensure you got the correct Firmware and restart Odin
4) select location of files according to Firmware ( single file in PDA )
5) unchecked the " protect ops file" box on the Odin screen before starting
That should do it
Yeah.. Follow the above steps and you are good to go...
If my post helped, don't mind hitting THANKS ;-)
xsenman said:
1) remove battery and reinsert
2) go into download mode
3) ensure you got the correct Firmware and restart Odin
4) select location of files according to Firmware ( single file in PDA )
5) unchecked the " protect ops file" box on the Odin screen before starting
That should do it
Click to expand...
Click to collapse
That does not work for me, At the pda it says: wrong image type.
but it doensn't work at any way with protect ops on/off, and not with pda or one package.
can anyone help me?
jeantje said:
That does not work for me, At the pda it says: wrong image type.
but it doensn't work at any way with protect ops on/off, and not with pda or one package.
can anyone help me?
Click to expand...
Click to collapse
ok, lets try this again
First remove battery and reinsert
1) "Select OPS" AriesVE.ops
2) Unzip/unrar the ROM you are flashing.
If it's a single .tar.md5 file, check the option "One Package" in Odin and then load the .tar.md5 file using the One Package button at the very bottom. Odin will load it and check the MD5 checksum. and should be over in ten minutes
If your ROM consists of several .smd files,
Select Boot_loader.tar under BOOT
Select Modem under PHONE
Select PDA under PDA
Select CSC under CSC .
Press Start, Flashing should take about 10 minutes
If it fails, than try again with protect ops unchecked
:'(
xsenman said:
ok, lets try this again
First remove battery and reinsert
1) "Select OPS" AriesVE.ops
2) Unzip/unrar the ROM you are flashing.
If it's a single .tar.md5 file, check the option "One Package" in Odin and then load the .tar.md5 file using the One Package button at the very bottom. Odin will load it and check the MD5 checksum. and should be over in ten minutes
If your ROM consists of several .smd files,
Select Boot_loader.tar under BOOT
Select Modem under PHONE
Select PDA under PDA
Select CSC under CSC .
Press Start, Flashing should take about 10 minutes
If it fails, than try again with protect ops unchecked
Click to expand...
Click to collapse
hello, i'm dealing with the same situation :/
after unchecking the "protect ops" it goes as far as the "big partition size" error message and stalls again...
really really in need of help guys... :/
aspetos said:
hello, i'm dealing with the same situation :/
after unchecking the "protect ops" it goes as far as the "big partition size" error message and stalls again...
really really in need of help guys... :/
Click to expand...
Click to collapse
jeantje problem was solved by re downloading the Aries.ops from another source as samfirmwares was corrupted
xsenman said:
jeantje problem was solved by re downloading the Aries.ops from another source as samfirmwares was corrupted
Click to expand...
Click to collapse
xsenman do you have a direct link of Aries.ops that works? ty
aspetos said:
xsenman do you have a direct link of Aries.ops that works? ty
Click to expand...
Click to collapse
try this, have not checked it as, I use different phone
CWM For flashing with Odin: http://www.mediafire.com/?jg0jjdg8amjlj3b
AriesVe.ops http://www.mediafire.com/?ikx8iz8arzabx1h
xsenman said:
try this, have not checked it as, I use different phone
CWM For flashing with Odin: mediafire com/ ?jg0jjdg8amjlj3b
AriesVe.ops mediafire com/ ?ikx8iz8arzabx1h
Click to expand...
Click to collapse
Is it normal that it now seems to be on "recovery.img download" for like 9 minutes?
I used the above CWM For flashing with Odin, AriesVE.ops and provided Odin version (verified same odin version was used as previous attempts).
The "Protect OPS" check box is checked, right?
aspetos said:
Is it normal that it now seems to be on "recovery.img download" for like 9 minutes?
I used the above CWM For flashing with Odin, AriesVE.ops and provided Odin version (verified same odin version was used as previous attempts).
The "Protect OPS" check box is checked, right?
Click to expand...
Click to collapse
minimum time is not less than 10 min, so give it time, yes protect ops should be checked, inly If failed than try unchecked
I solved this problem with BroodROM RC5 all-in-one tar file, here is what I did:
A) Remove the .md5 extension and make it .tar
B) Use other USB port
C) Remove KIES and downloaded standalone drivers pack
D) Sit back and waited for 30 minutes until flashing complete
xsenman said:
minimum time is not less than 10 min, so give it time, yes protect ops should be checked, inly If failed than try unchecked
Click to expand...
Click to collapse
23 minutes and counting...
just to check, nothing moves on the phone screen (like a bar indicator)
Is that normal?
aspetos said:
23 minutes and counting...
just to check, nothing moves on the phone screen (like a bar indicator)
Is that normal?
Click to expand...
Click to collapse
hmm, think its stuck, do a battery pull to get out of it and you can try darristan suggestion
xsenman said:
hmm, think its stuck, do a battery pull to get out of it and you can try darristan suggestion
Click to expand...
Click to collapse
tried with the "Protect OPS" unchecked (just in case), left it a fair 10+ minutes, no indication, etc...
I'll try darristan suggestion. But excuse me for asking to be a bit more elaborate as far as steps are concerned, it's like 7:30 AM here and had a long night...
Is there a post relative to darristan downloads and/or procedures?
ty
aspetos said:
tried with the "Protect OPS" unchecked (just in case), left it a fair 10+ minutes, no indication, etc...
I'll try darristan suggestion. But excuse me for asking to be a bit more elaborate as far as steps are concerned, it's like 7:30 AM here and had a long night...
Is there a post relative to darristan downloads and/or procedures?
ty
Click to expand...
Click to collapse
here http://forum.xda-developers.com/showthread.php?p=20392786
darristan said:
I solved this problem with BroodROM RC5 all-in-one tar file, here is what I did:
A) Remove the .md5 extension and make it .tar
B) Use other USB port
C) Remove KIES and downloaded standalone drivers pack
D) Sit back and waited for 30 minutes until flashing complete
Click to expand...
Click to collapse
unfortunately no luck either...
stuck on amss.mbn download again, with out any indicators on the phone screen...
am i properly foobared?
aspetos said:
unfortunately no luck either...
stuck on amss.mbn download again, with out any indicators on the phone screen...
am i properly foobared?
Click to expand...
Click to collapse
Suggest you read the i9001 WIKI http://forum.xda-developers.com/wiki/Samsung_Galaxy_S_Plus/GT-I9001#Flashing to check, if there is anything you may or may not be doing.
please help..!!!
my galaxy mini s-5570 from ornge uk (network locked).. got bricked. i can get into download mode and ramdump mode.
as i can get into download mode i tried to flash stock roms with odin ...every time odin detects phone and flashes successfully and PASSES ... but after the step "close serial port and wait untill reboot" my phone starts blinking again and not booting up.
i tried many stock roms i found here but all ending up the same way. i dont know what to do now...
phone can still get into download mode...
when i simply turn the phone on the samsung logo is blinking on the screen
please help me.. i dont know if it is because i am flshing wrong ROM or what? if so please provide me the proper rom for GALAXY MINI S-5570 ORANGE UK..PLEASE...
if it say pass mean all is gone in the right way so is good that you can go into download mode cuz you can flash a custom recovery with odin and with a custom recovery you can flash a new rom...like cm7 and you can see if the phone bootup
Sent from my GT-S5570 using xda premium
I had something similar. Try to find a multi package 2.2.1. It's not easy, but if you can flash that, it will reboot (at least for me)
here the link for 2.2.1 froyo
http://www.youtube.com/watch?v=7mv5d1q4Bfo
ok try thos also complete guide + 2.2.1 packages
http://www.sleetherz.com/2011/10/how-can-i-switch-back-my-galaxy-mini-to-default-froyo-2-2-1/
Sent from my GT-S5570 using xda premium
galaxy mini soft brick...
MAD_psycho_Zz said:
here the link for 2.2.1 froyo
ok try thos also complete guide + 2.2.1 packages
Sent from my GT-S5570 using xda premium
Click to expand...
Click to collapse
thank you for replying to my post...
but i tried the froyo with multiple files but still the same thing happening..
after "close serial port....." message. phone screen starts blinking ...not rebooting.. HERE IS WHAT I GOT WHEN I TRIED ONE MULTI FILE FIRM WARE...... S5570_XXKB1
Download Start...
<0> Create File...
<1> StartThread Detected : 0
<2> StartThread Detected : 1
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<2> setup connection...
<2> odin mode.. check plcatform verification.
<2> VerifyPlatform:V0, P0,R0
<2> START!!!
<2> set download environment.
<2> big partition size!!
<2> big partition size!!
<2> big partition size!!
<2> big partition size!!
<2> big partition size!!
<2> mibib download..
<2> 1/10 Finished.
<2> qcsbl download..
<2> 2/10 Finished.
<2> oemsbl download..
<2> 3/10 Finished.
<2> amss download..
<2> 4/10 Finished.
<2> arm11boot download..
<2> 5/10 Finished.
<2> boot.img download..
<2> 6/10 Finished.
<2> recovery.img download..
<2> 7/10 Finished.
<2> system.rfs download..
<2> 8/10 Finished.
<2> data.rfs download..
<2> 9/10 Finished.
<2> csc.rfs download..
<2> 10/10 Finished.
<2> reset pda..
<0> Started Timer
<2> Close serial port and wait until rebooting.
<2> PASS!!!
<0> Destroy instant..
<0> Killed timer
BUT AFTER close serial port and wait untill rebooting my phone just starts blinking ..
please help
Remove sim card, memory card.
Flash a stock firmware which has all the 4 files + .ops file.
After pass.
Pull battery out.
Put it back in.
Go into recovery.(Home+Power)
Clear User data and cache
Reboot.
chemicalrage said:
Remove sim card, memory card.
Flash a stock firmware which has all the 4 files + .ops file.
After pass.
Pull battery out.
Put it back in.
Go into recovery.(Home+Power)
Clear User data and cache
Reboot.
Click to expand...
Click to collapse
i took out battery and after puting it back i tried to go into recovery but not going in to recovery as before ...only download mode and ramdump mode are available
how strange...:/ try flashing froyo with the guide above...then flash stock gingerbread then flash a cwm recovery with odin and then try going into recovery mode and do a full wipe(cache data dalvik cache battery stats and format system in mount and storage menu) if u can do it mount usb from recovery put a custom rom into your sd flash it wipe data and cache again and reboot hopeing your phone will boot...
MAD_psycho_Zz said:
how strange...:/ try flashing froyo with the guide above...then flash stock gingerbread then flash a cwm recovery with odin and then try going into recovery mode and do a full wipe(cache data dalvik cache battery stats and format system in mount and storage menu) if u can do it mount usb from recovery put a custom rom into your sd flash it wipe data and cache again and reboot hopeing your phone will boot...
Click to expand...
Click to collapse
is there any possibility that it is stuck at boot screen because of files left behind by previous roms...? in tht case is there any tool to wipe the partitions before flashing (as i can not go into recovery mode the usual way of wiping is impossible)?
Now my phone is totally bricked....!!!!!
jaizkt said:
is there any possibility that it is stuck at boot screen because of files left behind by previous roms...? in tht case is there any tool to wipe the partitions before flashing (as i can not go into recovery mode the usual way of wiping is impossible)?
Click to expand...
Click to collapse
now...my phone is totally bricked.....!!!!!!!!!!!!!!!!!! AS I tried to flash the file "arm11boot" as boot file in odin (as told by some person in this forum...)
and now i dont have anything except a blank screen... USB JIG is also not working..... SO MY ADVICE TO ALL....PLEASE DONT FLASH THAT BOOT FILE USING ODIN IT WILL JUST BRICK YOUR PHONE... DONT REMEMBER THE NAME OF THAT PERSON WHO SUGGESTED IT..
TODAY I LEFT MY PHONE AT SAMSUNG SERVICE FOR GETTING MY MOTHERBOARD CHANGED....its bit costly (3800 indian rupees)... but i dont want to make my phone my paper weight...so....
jaizkt said:
now...my phone is totally bricked.....!!!!!!!!!!!!!!!!!! AS I tried to flash the file "arm11boot" as boot file in odin (as told by some person in this forum...)
and now i dont have anything except a blank screen... USB JIG is also not working..... SO MY ADVICE TO ALL....PLEASE DONT FLASH THAT BOOT FILE USING ODIN IT WILL JUST BRICK YOUR PHONE... DONT REMEMBER THE NAME OF THAT PERSON WHO SUGGESTED IT..
TODAY I LEFT MY PHONE AT SAMSUNG SERVICE FOR GETTING MY MOTHERBOARD CHANGED....its bit costly (3800 indian rupees)... but i dont want to make my phone my paper weight...so....
Click to expand...
Click to collapse
that's the bootloader u shouldn't play with it
The person who told you about the bootloader should be banned from xda. I swear what a jackass.
Messi10 said:
that's the bootloader u shouldn't play with it
Click to expand...
Click to collapse
Dear Messi,
i have done all the above successfully, including rooting with odin and installing cwm recovery.
but now on trying to install a custom rom it is stuck on android logo screen. after restoring to the stock rom, it gets stuck to samsung galaxy logo screen
pls help.. its urgent and its my sis in laws phone..
thanks in advance..
Bhupen Gaitonde said:
Dear Messi,
i have done all the above successfully, including rooting with odin and installing cwm recovery.
but now on trying to install a custom rom it is stuck on android logo screen. after restoring to the stock rom, it gets stuck to samsung galaxy logo screen
pls help.. its urgent and its my sis in laws phone..
thanks in advance..
Click to expand...
Click to collapse
Try wiping from CWM.
I got an ide a but Dino if this would work
if you could go to recovery mode that's good
get your SD card out and put it in your PC then download a ROM and then put it in the SD card after that put the SD card back to your phone and go to recovery and flash it like normal and don't forget to wipe
I Duno if this will work
edit:woops I think I'm late
Sent from my GT-S5570 using xda premium
jaizkt said:
now...my phone is totally bricked.....!!!!!!!!!!!!!!!!!! AS I tried to flash the file "arm11boot" as boot file in odin (as told by some person in this forum...)
and now i dont have anything except a blank screen... USB JIG is also not working..... SO MY ADVICE TO ALL....PLEASE DONT FLASH THAT BOOT FILE USING ODIN IT WILL JUST BRICK YOUR PHONE... DONT REMEMBER THE NAME OF THAT PERSON WHO SUGGESTED IT..
TODAY I LEFT MY PHONE AT SAMSUNG SERVICE FOR GETTING MY MOTHERBOARD CHANGED....its bit costly (3800 indian rupees)... but i dont want to make my phone my paper weight...so....
Click to expand...
Click to collapse
You paid a visit to Samsung center.
Was the problem solved?
If Your devices brick with Blank screen. you can test my way.
Step 1. Pull out your battery, Remove Sd card and SIM card.
Step 2. Connect your phone to pc or charger (Charge without battery)
Step 3. Pres Vol Up + Down and power.
Step 4. Put your battery back, now if work your phone will charging.
Step 5. go to download mode now and flash it.
I try this because my phone bricked with CWM.
Sent from my GT-S5570 using xda app-developers app
Hi!
I try to Instal ClockworkMod on my Samsung Galaxy S Plus to install CyanogenMod 10.1. I use this tutorial for that:
Pre-requisites:
Make sure that you have charged your mobile at least up to 70% so that installation process will occur without any interruption.
It is recommended that you should take a backup of all your important personal data such as SMS, MMS, APN, contacts etc. to the external microSD card.
You must install your mobile’s drivers on PC. If you have installed Kies on your computer then you don’t need to install it separately.
Procedure to install Clockworkmod recovery on Samsung Galaxy S Plus I9001:
First download Odin v4.43 software and install it on your PC. It is necessary for flashing recovery on mobile.
Click here to download.
Download Clockworkmod recovery for Samsung Galaxy S Plus.
Also download AriesVE OPS file.
Now you have to boot your mobile into downloading mode. For that, first switch off your mobile then press & hold volume down + power button + home button simultaneously until it shows downloading message on your screen.
Now connect mobile to PC via USB cable.
Launch Odin software which you have installed previously on your PC. You will see Added!! message in Odin’s message box. If you won’t get this message make sure that you have installed mobile drivers properly.
Now click on the OPS button and then select AriesVE OPS file.
Click One Package button on Odin and select cwm6032-ariesve-touch-odin.tar file which you have downloaded earlier.
Ensure that Auto-Reboot and F.Resest Time is checked. Make sure that you haven’t clicked anywhere else.
Hit start button to flash recovery on mobile. After successful installation of recovery your mobile rebooted automatically. At the same time you will get pass message in Odin’s message box.
However if you mobile get stuck or you get a fail message then exit the Odin, disconnect mobile from computer, remove battery and re-insert it and follow the above procedure again.
Well done! Clockworkmod Recovery is now installed on your Samsung Galaxy S Plus I9001. Do let us know how it is working. If you any query regarding this article, you can ask us freely. We will try our level best to solve it.
Note: For entering into Clockworkmod recovery press & hold volume up + power button + home button simultaneously.
Click to expand...
Click to collapse
After 30 minutes of waiting I unppluged mobile and turn it off. After rebooting I saw icon of mobile and computer with yellow triangle with exclamation mark. After working with this once more I go to download mode and now is more than next 30 minutes...
[
Odin massages:/FONT]
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
<1> START!!!
<1> set download environment.
<1> recovery.img download..
Click to expand...
Click to collapse
I waited for 50 minutes and turn off installation. Tryied 3 more times, only detecting wrong port if I try to change USB. What to do with this now?
Try the same with this. It'll be ok
NB: This is for i9001 only. Please don't try this in other devices.
It worked instantlly! Thank you very much!:good: Now I go to install CyanogenMod.
first sorry for my bad english
i tried 6.0.1.1 but after 20 min half get green but do nothing....what should i do? may i still waiting?
...i tried CWM 6.0.2.8 and its ok now
thx
Hello everyone, i have a Galaxy S Plus, i flashing with 2.3.6 Gingerbread without sim card, after installation with odin multi downloader with AriesVe.ops file i tryed insert the sim card but it was restarted or power off., but without sim card it's perfectlly, no problems, no restarts, no anything.
In recovery mode it displays status " >>> status = 00 >> and i have a option "install fota", please help me and sorry for my english.
Happy? said:
Hello everyone, i have a Galaxy S Plus, i flashing with 2.3.6 Gingerbread without sim card, after installation with odin multi downloader with AriesVe.ops file i tryed insert the sim card but it was restarted or power off., but without sim card it's perfectlly, no problems, no restarts, no anything.
In recovery mode it displays status " >>> status = 00 >> and i have a option "install fota", please help me and sorry for my english.
Click to expand...
Click to collapse
download the i9001 firmware from here for your region and flash again with ariesVe.ops
Check this out! Links to useful Guides and " Banned " Documentaries
flashing with sim card or without ? thanks.
Happy? said:
flashing with sim card or without ? thanks.
Click to expand...
Click to collapse
you can flash with SIM Card, its not a problem. Its possible the earlier ROM you flashed could have been corrupted.
Check this out! Links to useful Guides and " Banned " Documentaries
Thanks, i try this now but i have a problem. i try connect my galaxy to odin and recived a error port..i tryed other port usb and i have two yellow box in odin(can see in attache file). i tryed closed the odin and reopen but when open odin without connect my phone first yellow box recived a message: added, and after connect my phone displays a second yellow box. the process runs in a second box.
I have again same problem with sim card, restarted restarted.. please...help me.
p.s: i search my region for firmware but i not found. my region is romania, i tryed germany because is close.
please help me.
with respect.
Happy? said:
but when open odin without connect my phone first yellow box recived a message: added, and after connect my phone displays a second yellow box. the process runs in a second box.
Click to expand...
Click to collapse
I think you need to try with another PC or laptop, as com port should not connect when nothing is connected.
also charge you phone fully and KILL KIES, using task manager when flashing
Check this out! Links to useful Guides and " Banned " Documentaries
i try this, man, i uninstall the kies, now open two yellow box.
i restart my laptop, i connect my samsung in download mode to pc, i open the odin, message: added, detected, i upload .ops file and trd.md5 file and start, but recived error port, swich the port added also yellow box..and this is problem..
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 1
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
<1> START!!!
<1> set download environment.
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> amss.mbn download..
<1> 1/7 Finished.
<1> adsp.mbn download..
<2> --- cannot open the usb serial port. code: 2
<1> 2/7 Finished.
<1> boot.img download..
<1> 3/7 Finished.
<1> system.img.ext4 download..
<1> 4/7 Finished.
<1> cache.img.ext4 download..
<1> 5/7 Finished.
<1> recovery.img download..
<1> 6/7 Finished.
<1> preload.img.ext4 download..
<1> 7/7 Finished.
<1> reset pda..
<0> Started Timer
<1> Close serial port and wait until rebooting.
<2> Download Error (transfer)..
Click to expand...
Click to collapse
Happy? said:
i try this, man, i uninstall the kies, now open two yellow box.
i restart my laptop, i connect my samsung in download mode to pc, i open the odin, message: added, detected, i upload .ops file and trd.md5 file and start, but recived error port, swich the port added also yellow box..and this is problem..
Click to expand...
Click to collapse
download the Odin 4.43 as well as aries VE.ops file from another source and try.
Check this out! Links to useful Guides and " Banned " Documentaries
i try and this..not work..
Odin 4.43 , Odin 4.43 with SMD + Aries Ve.ops
attached
i try and this..not working. i have a question. why working without sim ? exist a possibil option to be change this error?
Happy? said:
i try and this..not working. i have a question. why working without sim ? exist a possibil option to be change this error?
Click to expand...
Click to collapse
Good question, but honestly have no idea as first time, I heard of this problem, where Odin connects without having phone attached.
But I would like to know
1) Is your IMEI still available when you flash without SIM card?
2) Did you get this phone recently? was this SIM blocked by Network or original owner?
read this for clarification
Check this out! Links to useful Guides and " Banned " Documentaries
I try flashing on other pc and odin i worked perfectly (just one box) but i have again sim card problem.
I try the custom room, again.. reboot when insert sim card.
Do you think that problem be solved with unroot? My phone is root..
Happy? said:
I try flashing on other pc and odin i worked perfectly (just one box) but i have again sim card problem.
I try the custom room, again.. reboot when insert sim card.
Do you think that problem be solved with unroot? My phone is root..
Click to expand...
Click to collapse
can you try flashing with the SIM card inside ( just check your sim card is inserted without force and no pins are damaged ( i know difficult to see that)
Check this out! Links to useful Guides and " Banned " Documentaries
Hi all,
I wanted to change the rom on my i9001 to EHNDROIX and I read in the forum (here: http://forum.xda-developers.com/showthread.php?t=2590896&page=3) that I should change the recovery to twrp, so I downloaded the zip file and put it onto the sdcard just as I used to in case of any rom update. I installed the recovery in recvery mode. After the installation the phone boot without any problem but I can't reach recovery. I'm able to boot to download mode so I tried to revert back to cwm recovery with Odin, but odin stuck on verifying platform.
Now I don't know what to do.
I updated the USB drivers, redownloaded ariesve.ops, odin, but it didn't helped.
Please help me getting back to recovery!
Thanks,
deadakos said:
but odin stuck on verifying platform.
Now I don't know what to do. ,
Click to expand...
Click to collapse
Look here [Tutorial][A.I.O. Rescue & Recovery] My Android Solutions. [Help & Troubleshooting], basically you need to kill KIES First and use the i9001 flashing guide
Check this out! Links to useful Guides and " Banned " Documentaries
xsenman said:
Look here [Tutorial][A.I.O. Rescue & Recovery] My Android Solutions. [Help & Troubleshooting], basically you need to kill KIES First and use the i9001 flashing guide
Thanks for your reply.
Of course I found this thread yesterday but I didn't understand why should I install an app from market to boot into recovery because my current rom, the unofficial slim support booting into recovery from the turn off menu.
So this morning I double checked everything what I read:
- check and kill kies (as kies is not installed, that was not an issue for me)
- check the usb cable (I used the Samsung cable, so that couldn't be a problem)
I made this morning the following :
- I turned off virus protection and firewall during the odin download process
- pluged the Samsung USB cable to one of the USB3 back port of my computer
- I run odin as administrator
- downloaded CWM touch recovery odin version 6.0.3.7 mentioned here: http://forum.xda-developers.com/wiki/Samsung_Galaxy_S_Plus/GT-I9001#Buttons
- I boot into download mode with the 3 button way
- Started the odin process with AriesVE.ops, one-package-ticked, recovery.tar.md5 loaded to one-package
Odin's messages were the following:
<1> recovery.img download..
<1> 1/1 Finished.
<1> reset pda..
<0> Started Timer
<1> Close serial port and wait until rebooting.
<1> PASS!!!
<0> Destroy instant..
<0> Killed timer
The process lasts for maximum 3-4 seconds, and my phone rebooted into the slim os. I tried to boot into recovery but after the SAMSUNG logo, I just see a black screen again.
I always try to search the forum for a solution as this time I did. I think I made everything carefully, as I used to change roms on my htc one x and on my i9000 quite often so I know that it is easy to make mistakes. I don't know what went wrong.
Please advise!
Is it possible that the bootloader is partially damaged? Know I don't dare to redownload bootloader via Odin not to completely kill my i9001 :/
What was strange all the time is that recovery downloads seemed to happen too fast.
Now the
Click to expand...
Click to collapse
deadakos said:
Please advise!
Is it possible that the bootloader is partially damaged? Know I don't dare to redownload bootloader via Odin not to completely kill my i9001 :/
What was strange all the time is that recovery downloads seemed to happen too fast.
Click to expand...
Click to collapse
Flash this recovery
i9001 CWM 6.0 for amss.mbn download.. problems with AriesVe.ops in Odin 4.43
i9001 Touch CWM 6.0
if cannot boot
Flash i9001 Boot.tar with AriesVe.ops in Odin 4.43
Check this out! Links to useful Guides and " Banned " Documentaries
xsenman said:
Flash this recovery
i9001 CWM 6.0 for amss.mbn download.. problems with AriesVe.ops in Odin 4.43
i9001 Touch CWM 6.0
if cannot boot
Flash i9001 Boot.tar with AriesVe.ops in Odin 4.43
Check this out! Links to useful Guides and " Banned " Documentaries
Click to expand...
Click to collapse
As I don't have amss.mbn problems I tried the second option where the link contained the ariesve.ops file together with cwm 6.0.1.0. Odin said that everything is ok, but I still couldn't boot into recovery.
Should I give a try to feamodrecovery, or try flashing the boot with the suggested boot.tar?
I searched the net for amss.mbn error, and I found a thread where you suggested to somebody to use an even older cwm for flashing. Do you think that I should also try it?
I don't want to bother you too much but I'm really clueless
xsenman said:
Flash this recovery
i9001 CWM 6.0 for amss.mbn download.. problems with AriesVe.ops in Odin 4.43
i9001 Touch CWM 6.0
if cannot boot
Flash i9001 Boot.tar with AriesVe.ops in Odin 4.43
Check this out! Links to useful Guides and " Banned " Documentaries
Click to expand...
Click to collapse
Is it possible to use adb to write recovery.img just as I have to do in case of the boot.img of my HTC One X every time I want to change rom?
deadakos said:
As I don't have amss.mbn problems I tried the second option where the link contained the ariesve.ops file together with cwm 6.0.1.0. Odin said that everything is ok, but I still couldn't boot into recovery.
Should I give a try to feamodrecovery, or try flashing the boot with the suggested boot.tar?
I searched the net for amss.mbn error, and I found a thread where you suggested to somebody to use an even older cwm for flashing. Do you think that I should also try it?
I don't want to bother you too much but I'm really clueless
Click to expand...
Click to collapse
It does not matter about amss.mbn as I am the one who wrote it for users to identify some issues. ( best avoid feamod recovery) , so go ahead and flash that recovery after that you can flash the boot.tar or a kernel meant for the ROM you have on your device.
Check this out! Links to useful Guides and " Banned " Documentaries
xsenman said:
It does not matter about amss.mbn as I am the one who wrote it for users to identify some issues. ( best avoid feamod recovery) , so go ahead and flash that recovery after that you can flash the boot.tar or a kernel meant for the ROM you have on your device.
Check this out! Links to useful Guides and " Banned " Documentaries
Click to expand...
Click to collapse
I flashed the cwm 6.0.1.0 with the enclosed ops as previously, just to be sure. After it, I turned off the phone, took out the battery, sd-card, sim card, and pushed the power button for at least 30 seconds, then put back only the battery. Then started odin as administrator, opened ops again, ticked one package, and choose the bootloader.tar. Booted into download mode by the three button method, connected to the computer with Samsung cable.
Pressed start, and odin stoped again on verifyplatform:
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
I'm in a vicious circle
I read here:
http://androidsansar.wordpress.com/...overy-for-the-galaxy-s-plus-i9001-using-odin/
and here also:
http://forum.xda-developers.com/showthread.php?t=2204700&page=22
to put the recovery tar.md5 to pda in Odin.
Could this be the reason why I can't flash recovery correctly?
deadakos said:
ticked one package, and choose the bootloader.tar. Booted into download mode
I'm in a vicious circle
Click to expand...
Click to collapse
well obviously, you are missing the point here, Odin has specific locations, for single files like recovery, modem phone, it should be selected as "PDA" for Bootloader it is seelcted under "BOOT" and when a full ROM is integrated as a single file, it is selected as a "SINGLE PACKAGE"
Check this out! Links to useful Guides and " Banned " Documentaries
Pfff, now it is completly bricked...
Maybe I'm stupid and did something wrong, but I rooted this phone, and it was not the first one, and I used it and changed roms for more than one year, and now only black screen awaits when pushing the power button.
I made a screenshot about odin, would you please check what did I wrong?
First I flashed the suggested recovery put into PDA. After it, because I still couldn't boot into recovery, I flashed bootloader put into boot section, just as on the attached screenshot.
Is there any chance to wake my phone up? JTAG?
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Here is Odin's last message list:
Download Start...
<0> Create File...
<1> StartThread Detected : 1
<2> StartThread Detected : 0
<3> StartThread Detected : 0
<4> StartThread Detected : 0
<5> StartThread Detected : 0
<6> StartThread Detected : 0
<7> StartThread Detected : 0
<8> StartThread Detected : 0
<1> setup connection...
<1> odin mode.. check plcatform verification.
<1> VerifyPlatform:V0, P0,R0
<1> START!!!
<1> set download environment.
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> big partition size!!
<1> partition.bin download..
<1> 1/4 Finished.
<1> dbl.mbn download..
<1> 2/4 Finished.
<1> osbl.mbn download..
<1> 3/4 Finished.
<1> EMMCBOOT.MBN download..
<1> 4/4 Finished.
<1> reset pda..
<0> Started Timer
<1> Close serial port and wait until rebooting.
<1> PASS!!!
<0> Destroy instant..
<0> Killed timer
deadakos said:
Is there any chance to wake my phone up? JTAG?
Click to expand...
Click to collapse
Is download mode possible? the image and flash seems good, only thing I can think of, is your power( battery ran out) which would cause such an issue like totally dead. Look in [Tutorial][A.I.O. Rescue & Recovery] My Android Solutions. [Help & Troubleshooting] about getting download mode , likely with USB JIG, failing which it should be recoverable by JTAG, (unless you have a internal SD card problem that has been the issue all along)
Check this out! Links to useful Guides and " Banned " Documentaries
xsenman said:
Is download mode possible? the image and flash seems good, only thing I can think of, is your power( battery ran out) which would cause such an issue like totally dead. Look in [Tutorial][A.I.O. Rescue & Recovery] My Android Solutions. [Help & Troubleshooting] about getting download mode , likely with USB JIG, failing which it should be recoverable by JTAG, (unless you have a internal SD card problem that has been the issue all along)
Check this out! Links to useful Guides and " Banned " Documentaries
Click to expand...
Click to collapse
No, nothing is possible at this moment. I don't think that the battery is the reason as it was fully charged before the flashing process, and my device was turned on for maximum 15 minutes. Just to be sure I connected it to the cord, but even the loading process doesn't start.
deadakos said:
No, nothing is possible at this moment. I don't think that the battery is the reason as it was fully charged before the flashing process, and my device was turned on for maximum 15 minutes. Just to be sure I connected it to the cord, but even the loading process doesn't start.
Click to expand...
Click to collapse
Now it is official, the phone is dead. It had hardware problems. RIP!
Thanks for your help!