[Q] [SOLVED] Broken Back Bottom Shield Socket - HD7 Q&A, Help & Troubleshooting

Hi XDA Community,
due to changing the micro sd card of my hd7 it happens (because of a little bit to strong pulled) that one of the tiny stock clips is broken. Now my bottom back shield is not anymore clipped in on the left top side of the bottom shield.
Is there a way to get a new back bottom shield?
Or has anyone an idea to fix this on my own?
I thought of any industrial glue like 2 component resin. Just a tiny drop and let it dry. But i dont know if i need to get there in anytime in the future. And after fixing it with 2 component resin i will never be able to remove the shield without total destruction.
So guys if anyone has an good idea, i would be really thankful fo rur advice.
nice regards Synergi

you get the back cover anywhere online....but bottom back is not available in the market....:/
I guess u have to use the glue
Or else buy a hard case and don't put the bottom back cover at all....
If you are not going to remove the bottom back cover just seal it with the glue

Ok thx mate, i will stick with the glue.

Related

Take Apart

Anyone know how to get the front bezel off this thing?
It's begging for a paint job.
Thx!
and perhaps a generous application of rubber cement. I had ONE creek point when i bought it - annoying but livable enough (plus the fact all the bad hours of xmas I was working I never had time to return it in the 30 day period to best buy). now almost 2 months latter theres three...
theres a teardown thread or two on here somewhere but the search button seems to be failing (or my browser....)
- Will.
It must pop off, but I don't want to be the guy to try it...
In the tear down I remember seeing roughly 10 small philips screws holding it from the inside to the metal sub structure. To tighten it you need to remove the back of the device then you will see the screws running around the perimeter. I also remember the screen is held to the bezel with a form of double faced tape.
waremaster said:
In the tear down I remember seeing roughly 10 small philips screws holding it from the inside to the metal sub structure. To tighten it you need to remove the back of the device then you will see the screws running around the perimeter. I also remember the screen is held to the bezel with a form of double faced tape.
Click to expand...
Click to collapse
Its funny because the guy at Best Buy was trying to pull the back off of the one I returned... No idea why he was trying to yank the back off of it...
I guess if he had succeeded I would have seen the screws..
Funny enough the display model NookColor at my local best buy was practically falling off. When I first looked at the device I nearly did not buy one because of that but then getting one in my hands at B&N changed my mind.
The front bezel is a "tape and cover" paint job. The screen is glued to the frame pretty solid. I had mine apart to fiddle around and to get the back off for a mold. Most of the screws are Torx #5 or #6. Tape it off good and you should be ok as far as the front bezel. The rear and metal frame you can easily get to by proper disassembly.
Here's the zdnet guide,
http://www.zdnet.com/photos/nookcolor-teardown/487636?seq=21
Here's what I did.
You'll need a torx 5. After you unscrews the 2 screws by the sd slot, use your nail along the chamfer corner to lift the back siding up. Then use a credit card to lift the back up and run along the edge to unhinged the back.
techboydino, are you going to make a new front bezel? might be a small after market for such things. I'd pick up a more solid one if the price was right.
actually metal front and back pieces would rock...
- Will.
I would like to see a silicon back cover case that has a kickstand..
WillCameron said:
techboydino, are you going to make a new front bezel? might be a small after market for such things. I'd pick up a more solid one if the price was right.
actually metal front and back pieces would rock...
- Will.
Click to expand...
Click to collapse
I was really considering metal but the fact that most would have to really take special care to actually seperate the bezel from the screen really kind of set me off that. making a case for this is rediculously hard. (compared to my attempts at other devices. if you ever seperated a screen for a cell phone from the glass then you know what I mean. I am trying to replace the back with aluminum and wanted to do a carbon fiber front. so far everything is too thick or just plain looks bad.
Ever heard of masking tape?
3M BLUE painters tape FTW
Glad to find this post!!!
This maybe a little off the subject but does any know where I can purchase a replacement faceplate frame cover.
I accidentally drop my nook color and now it has a nasty crack...
Thank you all in advance!
i took the kickstand off a picture frame...white glued it and had one. Then took it off to fit my new cover...replacement kickstand not put on yet..
nookme said:
This maybe a little off the subject but does any know where I can purchase a replacement faceplate frame cover.
I accidentally drop my nook color and now it has a nasty crack...
Thank you all in advance!
Click to expand...
Click to collapse
Your best bet is probably to pick up a smoked one off EBay or one with a cracked screen and a good bezel.
Actually post up WTB (want to buy) dead Nook Color in the XDA market and link to it in this thread. I seem to recall a couple readers here who have more than "gently used" Nooks....

[Q] Scratched screen- How do I replace it?

The screen on my Rogers HTC Raider is scratched. It is deep enough that I cannot remove by applying polisher. Screen still works but I rather replace the screen as the scratch is visible.
Where can I purchase the screen and replace it myself?
http://www.tmart.com/Replacement-LCD-Display-Screen-for-HTC-G19-Raider-4G_p137438.html
http://www.repairsuniverse.com/htc-vivid-screen-replacements-repair-parts.html
..
Thank you.
tap the thanks button
and good luck
A little advice - I've already replaced the screen on my Raider
Hi, glad someone else is attempting this. I had never replaced a screen in a phone before trying this so for me it was a little hair raising the first time I took it apart. On the back of the phone under the battery cover are 5 screws you need to remove, and one little plastic cover. Under the cover is the connector from the mainboard. Its just a little pop out connection, gently lever it loose before removing the shell to avoid hurting the ribbon.
Once you get this far, flip the phone face-up, and *from the bottom*, gently lever the sides and bottom of the plastic shell away from the screen. Its relatively easy.
Continue working along the edges toward the top until the plastic shell pops free, after that put it face-down again and remove the screws holding the battery holder to the rest of the phone. Pull it up and out to the left to remove it, being careful not to bend the battery contacts as they stay with the rest of the phone. Keep the screws with it, trust me - its easier to remember what goes where this way.
Once you have the battery holder off, put it aside and remove the screws holding the mainboard(s) to the shell. Also you will find three wires with little cup contacts at the ends, gently detach these as well, and when the screws and wires are off, carefully remove the boards. Look closely at the plastic tabs holding them in and you'll see how they come out. When taking them out of the phone you'll need to lift them like you were opening a book - ie. folding them to the right. Underneath are two sockets with ribbon cable connections, one should already be detached - the other can be popped off at this point. If you skipped detaching it at the beginning, now's the time to remove both.
This should leave you with two free boards attached in the middle by a black ribbon. Put them aside and what you have left in your hand is the metal shell, LCD, and digitizer.
NOW..the crappy news. This wonderful, beautiful, powerful, ESPENSIVE phone, is held together by black double-sided tape. Yep. Tape. AND you'll need some more before installing the new digitizer. I ordered mine from tmart as well and it not only comes with the wrong screwdrivers (btw you need a #1 philips bit - VERY tiny!!) but it doesn't come with any adhesive to mount the screen to.
Your new screen should also come with some prying tools, and they are quite handy. The guitar pick one didn't do much but the lever is very handy. You'll need to gently pry the digitizer away from the LCD with this tool being careful not to put too much pressure on the lcd or it might snap. Its only a few mm thick. GO SLOW.. you should have no problems. I've done it a few times now - I'm kinda rough on my toys.
Once you have the part un-taped, its still got the ribbon cable going back behind the lcd. Its connected to a small, thin socket on ther board. You lift a small white lever (remove the tape and save it - reapply it to the new connection) and slide the cable out. You'll need to use your lever again and pry up the lcd enough to slide the ribbon out from behind it. This can be tricky. Again, go slow, be real cautious..the tape is pretty strong. Once you have the panel out completely its just a matter of reversing the process. If you're real careful when removing the original panel, you might be able to reuse the double-sided tape thats in there.. I wasn't so lucky. Mine was covered in glass shards, as I mashed my screen pretty good.
Hope this helps!! I had a rough time the first time, but now its easy for me. I like taking it apart lol..
Let me know how you do! Good luck!
Brian

Raplacing the digitizer

Ok so i have a cracked digitizer...
I am going to replace it myself, however this phone is obviously not a straight forward repair.
Anyone have any personal experience replacing the digitizer on this phone? I have seen the youtube videos and read the xda.cn chinese breakdown, just looking for some personal input on the process if someone has one.
Also what will i need to rebuilt it? Do i need double sided tape etc. Thanks
80 views and no ones ever had experience with this?
i replaced it on 2 hd7 phones.
its a real pain to get it off because the glue tape they use goes all the way around, and its strong stuff.
you need to take apart the entire phone to get to the ribbon cable where the digitizer plugs in, so just look for some youtube videos of a tear down and watch carefully.
honestly the hardest part for me was getting the screen and digitizer clean of fingerprints and tiny broken glass pieces without messing up the screen, while keeping the double sided tape i put on in place and intact.
just take your time and everything will go smoothly.
-edit- yes you will need some double sided tape because when you take the digitizer off the sticky layer of the tape goes with it, the rest of the tape stays on the screen and is impossible to get off without damaging your screen so you have to apply new tape over it.
i used some thin scotch brand double sided tape and i cut it into long narrow strips with a razor using my old digitizer as a cutting board, the same width as the original tape.
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
CraiGDaniel said:
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
Click to expand...
Click to collapse
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
StevetotheH said:
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
Click to expand...
Click to collapse
um no they arent spacers...they are what directs the light to the 3 bottom keys. they are there for a reason so i recommend using them... ... now you are spot on with the 3m tape as it is the tape needed to do this whole job properly... the scotch crap is not made for this and WILL NOT HOLD UP NOR SEAL PROPERLY>>>
and for the person who said to put the tape over the old.... not a good idea... it can be removed and new should be used to replace the old..
sorry but i do this daily for a living so i do have a clue about this... just trying to help make it a successful repair and not one that ends up in my shop after the home repair failed and it damaged more than just the screen.....

Replacing back panel adhesives

hi friends,
I need to replace my back panel adhesive strips, can anyone please post a guide for how to do that? thanks in advance
come on guys, please
I had to open my Xperia Z once, to replace the headphone connector and I found good help opening the device in this video:
http://www.youtube.com/watch?v=jNrtamZuf7E
I ordered the spare parts on the site that posted the video; www.rounded.com. They also sell a complete adhesive strip for the back-cover:
http://rounded.com/sony-xperia-z-l36h-back-cover-adhesive.html
This back-cover strip is fixed in the correct shape between two plastic foils so placing it is as easy as positioning double-sided tape on the back of a poster.
Just watch out: rounded.com is a dutch company, so shipment to the US might take quite a while and half of the mails they send contain some dutch-english gibberish.
thank you very much I really appreciate it, so do I need to heat the strips and use clamps to hold the back cover after installing them?
No, the adhesive strip I got was self-sticking. I just centered it inside the phone and put the back cover on. After about half a minute of pressure around the edges of the back cover, it was like new. It's also waterproof again.
thanks man for all your helps

[Q] help finding nexus 6 plastic frame

I need help finding a peice. I ordered a screen replacement and it did not come with the plastic screw mount. I attached a picture of the part I need.
I need this peice because the old one has old adhesive strips stuck to it and I can't remove them.
http://www.etradesupply.com/motorola/android-models/motorola-nexus-6.html?p=2
Mudderz said:
I need help finding a peice. I ordered a screen replacement and it did not come with the plastic screw mount. I attached a picture of the part I need.
I need this peice because the old one has old adhesive strips stuck to it and I can't remove them.
Click to expand...
Click to collapse
You can remove the adhesive. Rub it with your finger, and it will start to roll up and come off. And yes, it is a slow, labor intensive process, but it does work.
Anybody know how to replace this piece? I don't know how to separate the plastic from the glass.

Categories

Resources