Replacing back panel adhesives - Xperia Z Q&A, Help & Troubleshooting

hi friends,
I need to replace my back panel adhesive strips, can anyone please post a guide for how to do that? thanks in advance

come on guys, please

I had to open my Xperia Z once, to replace the headphone connector and I found good help opening the device in this video:
http://www.youtube.com/watch?v=jNrtamZuf7E
I ordered the spare parts on the site that posted the video; www.rounded.com. They also sell a complete adhesive strip for the back-cover:
http://rounded.com/sony-xperia-z-l36h-back-cover-adhesive.html
This back-cover strip is fixed in the correct shape between two plastic foils so placing it is as easy as positioning double-sided tape on the back of a poster.
Just watch out: rounded.com is a dutch company, so shipment to the US might take quite a while and half of the mails they send contain some dutch-english gibberish.

thank you very much I really appreciate it, so do I need to heat the strips and use clamps to hold the back cover after installing them?

No, the adhesive strip I got was self-sticking. I just centered it inside the phone and put the back cover on. After about half a minute of pressure around the edges of the back cover, it was like new. It's also waterproof again.

thanks man for all your helps

Related

Help i need touch screen replacement guide for htc diamond

Hi i need a touch screen replacement guide for htc diamond
same here, anyone?
http://www.mediafire.com/?jnh4f2ndyzz
@mod: please remove this post if it is not allowed to post such links
http://www.pdacenter.ru/razborka/razbor-htc-touch-diamond/
gmvmg said:
http://www.mediafire.com/?jnh4f2ndyzz
@mod: please remove this post if it is not allowed to post such links
Click to expand...
Click to collapse
check the wiki....points to the same link
Awesome... Thanks
Well i had the same issue and I had to give it to the service center and I got it back after 2 mnths yea i know it's a long time but i guess it was worth it in the end... but looking at how to do it urself I think it's a huge risk.... to even do it....
I've followed these steps and got to the last part. The service manua doesn't explain how to lift the LCD / touchscreen out (it's covered by grey tape). Does anyone know how to do the last steps?
I cant download that manual to see how far it goes but assuming you get as far as removing the 3 screws and removing the chassis plate to expose the rear of the LCD (can see the LCD part number 62H00004-31M)
All that holds the screen in now is adhesive, you can release this by, from the front, inserting an artists pallette knife around the sides and top and gently and progressively levering up to break the bond. Do not do this at the bottom or you will likely damage the flexi.
You now have an assembly which consists of a glass lens with the LCD bonded to the back and the digitiser bonded to the front, it is probably easier in the long run to replace this whole assembly.
To remove the digitiser lift the silver bonding tape and then the kapton tape from the digitiser connector (4 track connector) and de-solder the connector
To remove the digitiser from the front of the glass lens it is beneficial to heat it slightly (around 60 deg C). Then insert the pallette knife between the digitiser and the glass and slice it off - there is quite a lot of adhesive so take it carefully and do not lever as it may break the glass. Once the digitizer is off the glass needs to be cleaned of adhesive. Label removing fluid is good for this but ensure it doesn't get ino the LCD as it will ruin it.
All you need to do now is fit a new digitiser using optically clear adhesive-a tricky job unless you have a pressing fixture to ensure no air bubbles. I've also found that a lot of replacement Digitisers come complete with the glass lens and as it is impossible to remove the old LCD from the lens without cracking, they would seem pretty pointless to me?

Raplacing the digitizer

Ok so i have a cracked digitizer...
I am going to replace it myself, however this phone is obviously not a straight forward repair.
Anyone have any personal experience replacing the digitizer on this phone? I have seen the youtube videos and read the xda.cn chinese breakdown, just looking for some personal input on the process if someone has one.
Also what will i need to rebuilt it? Do i need double sided tape etc. Thanks
80 views and no ones ever had experience with this?
i replaced it on 2 hd7 phones.
its a real pain to get it off because the glue tape they use goes all the way around, and its strong stuff.
you need to take apart the entire phone to get to the ribbon cable where the digitizer plugs in, so just look for some youtube videos of a tear down and watch carefully.
honestly the hardest part for me was getting the screen and digitizer clean of fingerprints and tiny broken glass pieces without messing up the screen, while keeping the double sided tape i put on in place and intact.
just take your time and everything will go smoothly.
-edit- yes you will need some double sided tape because when you take the digitizer off the sticky layer of the tape goes with it, the rest of the tape stays on the screen and is impossible to get off without damaging your screen so you have to apply new tape over it.
i used some thin scotch brand double sided tape and i cut it into long narrow strips with a razor using my old digitizer as a cutting board, the same width as the original tape.
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
CraiGDaniel said:
Hi mate appreciate the advice in my thread on the HD7 replacement.
I managed to get the digitizer out, however on replacing the new one i have a problem..
You know the old digitizer has three plastic prongs, on the buttons at the bottom, search etc.
Am i rigth in saying they need to be transferred to the new digitizer? As i can't see how they fit on the LCD when stuck to the digitizer? It raises the digitizer a little, unless they hand off the edge of the lcd?
Thanks
Click to expand...
Click to collapse
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
StevetotheH said:
Those are nothing more than spacers. I have replaced two digitizers without them. As long as you get some good 3M double sided in that area there is no problems.
Click to expand...
Click to collapse
um no they arent spacers...they are what directs the light to the 3 bottom keys. they are there for a reason so i recommend using them... ... now you are spot on with the 3m tape as it is the tape needed to do this whole job properly... the scotch crap is not made for this and WILL NOT HOLD UP NOR SEAL PROPERLY>>>
and for the person who said to put the tape over the old.... not a good idea... it can be removed and new should be used to replace the old..
sorry but i do this daily for a living so i do have a clue about this... just trying to help make it a successful repair and not one that ends up in my shop after the home repair failed and it damaged more than just the screen.....

[Q] [SOLVED] Broken Back Bottom Shield Socket

Hi XDA Community,
due to changing the micro sd card of my hd7 it happens (because of a little bit to strong pulled) that one of the tiny stock clips is broken. Now my bottom back shield is not anymore clipped in on the left top side of the bottom shield.
Is there a way to get a new back bottom shield?
Or has anyone an idea to fix this on my own?
I thought of any industrial glue like 2 component resin. Just a tiny drop and let it dry. But i dont know if i need to get there in anytime in the future. And after fixing it with 2 component resin i will never be able to remove the shield without total destruction.
So guys if anyone has an good idea, i would be really thankful fo rur advice.
nice regards Synergi
you get the back cover anywhere online....but bottom back is not available in the market....:/
I guess u have to use the glue
Or else buy a hard case and don't put the bottom back cover at all....
If you are not going to remove the bottom back cover just seal it with the glue
Ok thx mate, i will stick with the glue.

How can I remove the back from a Doogee Y6?

Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Droidriven said:
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Click to expand...
Click to collapse
Already search extensively, no luck so far. Prefer not to 'experiment' and wreck the thing!
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Bro check YouTube very well... it there
Sent from my iPhone using Tapatalk Pro
I can help you.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Did u fix it? I can help you. I opened the phone like 10+ times.
Hi, I have the same problem, I need to open the phone to replace the camera but did not manage to find anything on youtube. Would u please help me? Thanks
Monster 00 said:
Did u fix it? I can help you. I opened the phone like 10+ times.
Click to expand...
Click to collapse
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
kiwironnie said:
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
Click to expand...
Click to collapse
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Monster 00 said:
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Click to expand...
Click to collapse
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
kiwironnie said:
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
Click to expand...
Click to collapse
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Monster 00 said:
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Click to expand...
Click to collapse
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
kiwironnie said:
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
Click to expand...
Click to collapse
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Monster 00 said:
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Click to expand...
Click to collapse
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
kiwironnie said:
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
Click to expand...
Click to collapse
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Monster 00 said:
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Click to expand...
Click to collapse
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
kiwironnie said:
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
Click to expand...
Click to collapse
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Monster 00 said:
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Click to expand...
Click to collapse
Brilliant, thanks again! No need for a video, as your explanation is very clear and should be obvious to others after they get the back off the phone. Having recently removed a glued battery from a Kindle, it was a hell of an arm wrestle! Hopefully it will be a bit easier with the Y6. I have a flat nylon spudger with a rounded edge, which should be able to lift the battery without puncturing it. Upgrading the speaker at the same time could be a useful hack, if a better one can be found that fits. Although don't know if the impedance is the same for most phone speakers.
Will post results here including any lessons learnt. Cheers Ron.
The replacement usb charge board arrived, purchased from this guy: http://www.ebay.com/itm/New-Origina...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 Posting the url as the service was excellent. Very well packed in its own cardboard box and sent by registered post. So I would buy from him again, even if he is a little more expensive than some on AliExpress.
To fit the new board, the case was opened, as described above and the battery removed. To remove the battery, two screws need to be removed from a metal plate covering the battery connector. The battery ribbon cable connector can then be levered up with a small flat screwdriver blade. It's a effectively a plug with a push fit onto the connector so just pops off.
To remove the battery I used an old credit card, sliding it underneath at one edge of the battery, then gently pushing it forward to release the battery bit by bit, from it being glued to the base. This shouldn't need a lot of force and it is important to avoid snagging the ribbon cable that runs under the battery.
The black plastic cover that houses the speaker and covers the charging board was then removed by unscrewing 4 screws. On my phone one screw had a white plastic covering, into which a cross head jewellers screwdriver can be pushed to grip the screw. The charger board was then exposed and the two speaker wires and two wires from the vibrator were unsoldered using a fine tip iron. The plastic cover was then fully removed. The black rubber tape covering the ribbon cable connector was scraped away, the connector unlocked and the ribbon cable removed. The antenna connector attached to the charger board was then levered off using a small flat bladed screwdriver. The charger board itself was then pulled out. It is held in place by tiny plastic tabs on either side and was a bit of a fiddle to remove.
The old charger board has some Kapton or similar tape underneath, which the new board didn't have. So I applied some similar tape to the new board, but this may not be essential. The new board was then fitted back in, again a bit of a fiddle. I found the best way was was to insert the right hand side of the board first under its tab (looking at the inside of the phone from the charger end), with the board rotated slightly anti clockwise, then pushing the left hand side forward (rotating clockwise) and under the left hand tab so that it effectively clicks into place (not much of a click). The rest of assembly was the reverse of disassembly. Soldering the 4 wires (polarity is marked on the board), pushing the ribbon cable squarely into the connector and locking it. Nearly forgot to push the antenna connector back on!
Replaced the back and the new charge board worked perfectly. What a relief! Thanks again to Monster for getting me started. Cheers Ron.
Hello everyone,
I have every tool needed to fix any problems on any mobile phones. But after fixing my y6, I have thought that a T5S would be piece of cake. But it's not.
Any ideas if I can just remove the broken digitizer to attach the new one or is it glued to the LCD like all new Samsung models?

Broken front glass (& usb port) - replacement?

Hi guys,
has anyone of you tried changing the front glass without digitizer and display?
In disassembly videos I can only see people changing the whole thing.
Also, do you think I can manage to repair the front glas as well as the USB port with just an iron instead of a hot air blower (and the usual tools made of plastic)?
Thanks in advance!
kadofl said:
Hi guys,
has anyone of you tried changing the front glass without digitizer and display?
In disassembly videos I can only see people changing the whole thing.
Also, do you think I can manage to repair the front glas as well as the USB port with just an iron instead of a hot air blower (and the usual tools made of plastic)?
Thanks in advance!
Click to expand...
Click to collapse
I haven't done the front glass on mine yet, but my understanding is that in general you're really better off replacing front glass as an entire unit with digitizer and display. An iron on pretty low through a cloth/towel might well work. It's not just glue that melts, it's a thin strip of rubber gasket material with adhesive (okay, maybe it's thick glue, but it looked pre-formed to me) holding the glass back cover on.
Heating probably helps a bit with softening the stuff, but after the first time you peel it up you won't really need to do that again. I'd recommend picking a corner (say, bottom left as you're looking at the back) and just plan on prying from there every time, so you only have one spot where the plastic gets marred.
Don't spend too much time heating, worry more about having a suction cup tool that you can lift with while you try to work a guitar pick or hobby knife or something in under the corner. Have at least two ready, so you can wedge one in, and work your way around without it just dropping back down on you. You'll probably tear the material a bit but that's okay, just spread it back out evenly around the edge on the glass before you put the cover back on. Also, you definitely should be using a case to make sure it doesn't just fall off in your pocket once you've opened it up a couple times.
USB cable replacement isn't awful, just time consuming. The biggest gotcha is to keep all three of the little gold clips on the plastic "mid frame" ring (that's the first thing you remove that requires screws after getting the back glass up) from fallling and getting lost.
You can PM me if you have any questions about this, I've replaced my USB cable/port assembly a couple times (first replacement was defective). And I'm about to attempt replacing the screen as a whole unit with glass & digitizer on my wife's Z2 Plus, so I'll let you know how that goes.

Categories

Resources