Hi,
my girlfriend just came back from China with a P1000 from her friend. As the whole device was running on chinese language and for some strange reason it was not possible to enter System Setting to change the language, I decided to flash her the latest firmware and just make a fresh start. (i'm a flash veteran on my SGS since 2 years, so I know how to use Odin)
I downloaded the P1000XWJQ8 from Sammobile, fired up Odin and flashed the new ROM with repartition enabled.
The procedure went through without errors:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P1000XWJQ8_P1000XXJPZ_P1000DBTJQ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Sbl.bin
<ID:0/003> param.lfs
<ID:0/003> zImage
<ID:0/003> cache.rfs
<ID:0/003> hidden.rfs
<ID:0/003> modem.bin
<ID:0/003> factoryfs.rfs
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
<ID:0/003> Added!!
At the end of it the device didn't auto-boot as expected, it just stayed there with a black screen!!!!!!
Disconnecting and reconnecting it triggers in Odin the REMOVED and the ADDED lines but nothing happens.
I cannot switch on, cannot go into download nor recovery, the device just seems to stay dead :-(
My next idea was trying to pull the battery but apparently the battery is glued to the casing, so before I do more damage, I better start asking here.
Hope someone can help, my girlfriend will kill me if I can't repair this damn thing...
EDIT: after having closed Odin on the PC I tried to connect the device again and it started to play the startup song and Win7 started to install the new drivers from the new firmware. 7 out of 9 found drivers installed correctly, 2 instead failed.
But nothing changed to the vegetarian state of the P1000
EDIT 2: now, after 12 hours wait, the device doesn't do anything anymore when I connect it to the PC, no USB connect, no sign of adding it in Odin. It seems like the charging mechanism doesn't work anymore either. The deivce appears totally dead.
Did you see my thread http://forum.xda-developers.com/showthread.php?t=1769144? This problem is totally the same as mine.
Is yours rooted? Coz it says here http://www.teamovercome.net/p1000/?page_id=17 that :
[REQUIRED FOR FROYO-BASED TABS ONLY:] Your Tab must be rooted. (Please look for SuperOneClick root method as it’s usually the safe bet! But for more information on rooting, please refer here: http://forum.xda-developers.com/showthread.php?t=812367)
Click to expand...
Click to collapse
I hope someone can help us, or else, no choice but to bring this to service center.
itenos said:
Hi,
my girlfriend just came back from China with a P1000 from her friend. As the whole device was running on chinese language and for some strange reason it was not possible to enter System Setting to change the language, I decided to flash her the latest firmware and just make a fresh start. (i'm a flash veteran on my SGS since 2 years, so I know how to use Odin)
I downloaded the P1000XWJQ8 from Sammobile, fired up Odin and flashed the new ROM with repartition enabled.
The procedure went through without errors:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> P1000XWJQ8_P1000XXJPZ_P1000DBTJQ1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Sbl.bin
<ID:0/003> param.lfs
<ID:0/003> zImage
<ID:0/003> cache.rfs
<ID:0/003> hidden.rfs
<ID:0/003> modem.bin
<ID:0/003> factoryfs.rfs
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
<ID:0/003> Added!!
At the end of it the device didn't auto-boot as expected, it just stayed there with a black screen!!!!!!
Disconnecting and reconnecting it triggers in Odin the REMOVED and the ADDED lines but nothing happens.
I cannot switch on, cannot go into download nor recovery, the device just seems to stay dead :-(
My next idea was trying to pull the battery but apparently the battery is glued to the casing, so before I do more damage, I better start asking here.
Hope someone can help, my girlfriend will kill me if I can't repair this damn thing...
EDIT: after having closed Odin on the PC I tried to connect the device again and it started to play the startup song and Win7 started to install the new drivers from the new firmware. 7 out of 9 found drivers installed correctly, 2 instead failed.
But nothing changed to the vegetarian state of the P1000
Click to expand...
Click to collapse
MarlX said:
Did you see my thread http://forum.xda-developers.com/showthread.php?t=1769144? This problem is totally the same as mine.
Is yours rooted? Coz it says here http://www.teamovercome.net/p1000/?page_id=17 that :
I hope someone can help us, or else, no choice but to bring this to service center.
Click to expand...
Click to collapse
hey guys, are sure your gtab is P1000??
see the back cover, and chek your gtab model to make sure.
qm4n76 said:
hey guys, are sure your gtab is P1000??
see the back cover, and chek your gtab model to make sure.
Click to expand...
Click to collapse
Yes, 100% sure, my one is a P1000. As wrote in EDIT2 my device now seems to be totally dead
Related
hi guys,
my phone doen't work anymore..
when i press the power button nothing happens.
when i try to get into odin mode nothing happens.
when i plug in usb cable nothing happens.
its totally dead.
anyone idea what i can do?
or shall i send it to samsung?
thanks
lol4it said:
hi guys,
my phone doen't work anymore..
when i press the power button nothing happens.
when i try to get into odin mode nothing happens.
when i plug in usb cable nothing happens.
its totally dead.
anyone idea what i can do?
or shall i send it to samsung?
thanks
Click to expand...
Click to collapse
What exactly did you do to arrive at that point?
Sent from my GT-N7000 using Tapatalk 2
tried to flash using odin 1.85
ehmmm maybe try to charge battery. And sometimes phone works but screen isnt, try to go in download mode and to check is it connecting to odin even if screen is black ;D gl
batterie is charged.
already tried everything i know
i dont think so that after flashing with 1.85 odin you would get hard brick, i think that you messed up with files in not right sections and baam- brick :/
yes youre right
i just plugged into my pc and windows is searching for samsung mobile usb composite device drivers..
and now finaly odin found it too
i think i just paniced too hard...
where can i get a original firmware?
lol4it said:
yes youre right
i just plugged into my pc and windows is searching for samsung mobile usb composite device drivers..
and now finaly odin found it too
i think i just paniced too hard...
where can i get a original firmware?
Click to expand...
Click to collapse
www.sammobile.com all official firmwares ;D
ok gonna try:
GT-N7000 N7000XXLPY 4.0.3 2012 May N7000OXALPY Open Germany Download Unlock
(got vodafone germany)
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLPY_N7000OXALPY_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
lol4it said:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLPY_N7000OXALPY_N7000XXLPT_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
you extracted zip file? you need to put .tar file at PDA ^^
ok
now my pc find my phone as unknown device -.-
and odin nothign..
ok worked now:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
<ID:0/003> NAND Write Start!!
<ID:0/003> zImage
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
but when i press power button still black screen??
EDIT: do i have to change standard settings like re-partition or flash lock?
lol4it said:
ok worked now:
Code:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> factoryfs.img
<ID:0/003> NAND Write Start!!
<ID:0/003> zImage
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> cache.img
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/003> Removed!!
but when i press power button still black screen??
EDIT: do i have to change standard settings like re-partition or flash lock?
Click to expand...
Click to collapse
i didnt change settings like re-partition and etc. You fcked up something, a lot of people flashed without problems
yes i know =(
but i dont think my screen is broken..
wtf is this?? someone must help me
i got sound and everthing but dat screen is BLACK
Sorry mate phone had dont suppose u would sell as need screen for mine as drop it
Sent from my GT-N7000 using xda premium
Tried to flash aokp jb 4.1.2 milestone1 rom on my galaxy note ics 4.0.4.Launched cwm recovery mode and wiped data,which went off fine but when I flashed the aokp milestone 1 rom the whole thing stuck for few minutes and suddenly the screen went blank.I waited long hoping it would restart... but it didnt.Opened the battery,reinstall it and tried to switch on but failed..I also tried to launch the Cwm recovery ,also tried the download mode but the phone refused to start.... please help....
dead battery?
nokiamodeln91 said:
dead battery?
Click to expand...
Click to collapse
No... I charged the phone before proceeding....it was around 90-95% when I started....!!!
Hello Friends!
I have bricked my s5830i ace, while I wanted to return to stock with odin. Unfortunately I didn't check USB debugging, so I couldn't flash it.
The problem is the following:
-Usb debugging isn't checked=>Can't flash=>Can't unbrick
Please help me! If i connect the phone to the first USB, odin says: Operation(Write) failed...or something...I can't try now.
Or when I connect to the second USB, odin says: Connecting(or something like that) and stucks...
Please help me! I'm very nervous, and I don't want to bring it to service!
You're my last hope
(If you need details, I could have a look at flashing process, and messages)
Well, how did you brick it? Seems like you flashed the wrong firmware (a firmware for 5830 without the 'i')
If that's the case and odin is stuck at setting up connection, then bad luck. A jtag (if you know someone with one) or service center are your options.
I'm sad to hear that. I wanted to flash the official 2.3.6 from samfirmware. If I know well, I should use Odin 1.84, or 1.85 and the file, which I have downloaded should be under PDA section...
Does your ace still go into download mode?
If so, it might be fixed by flashing the correct firmware.
Make sure to have your firmware in your pc root (C:/) since i've read that it helps.
I've put the correct firmware (Samfirmware S5830i Hungary Telenor)...It boot into download mode without any problem. I haven't tried to put the md5 file to the root, but I will try it soon. Thanks. I hope It's a good idea.
But I think I should check USB debugging in settings, but I can't do this, because It's bricked
coda00 said:
But I think I should check USB debugging in settings, but I can't do this, because It's bricked
Click to expand...
Click to collapse
As far as I'm concerned, usb debugging doesn't matter when flashing via odin. Edit: confirmed, since in download mode the system isn't loaded, there's nothing to debug.
Most odin problems occur when using wrong firmware, wrong .ops file or filename, when drivers aren't installed, or when not running odin as admin.
Okay....nothing worked.
I've tried everything, which you've said.
Odin write me every time:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXLD3_S5830iBTULC1_S5830iXXLD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl.bin
<ID:0/004> BcmCP.img
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
That's all...I tried everything...maybe my last chance is the service
OK.....news...
I've tried to remove the Rafael.Baugis kernel, and I got new message from Odin:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> S5830iXXLD3_S5830iBTULC1_S5830iXXLD2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl.bin
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response form LOKE
<ID:0/004> BcmCP.img
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response form LOKE
<ID:0/004> boot.img
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004> Receive Response form LOKE
<ID:0/004> system.img
<ID:0/004> Transmission Complete..
<ID:0/004> Now Writing.. Please wait about 2 minutes
<ID:0/004>
<ID:0/004> Receive Response form LOKE
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
WOW...
Problem solved
I've found a multi package here:
http://forum.xda-developers.com/showthread.php?t=1822109
It helped me...my phone is unbricked again
And of course I've flashed the stock rom too.
Hi
I did an OTA update to Jellybean yesterday which Three (3) put out and it all went smoothly. I was making a phone call today and the phone suddenly died. Now every time I turn it back on it loads and stays on for about 30 seconds at which point it dies again.
I've tried it with/without charger and SD card but it's the same result each time. Tried using Kies to re-install the firmware but the phone doesn't stay on long enough for me to.
Is there anything I can try before giving it to Three for a month?
Thanks.
Download a stock firmware from sammobile and flash it using odin
_McShane_ said:
Hi
I did an OTA update to Jellybean yesterday which Three (3) put out and it all went smoothly. I was making a phone call today and the phone suddenly died. Now every time I turn it back on it loads and stays on for about 30 seconds at which point it dies again.
I've tried it with/without charger and SD card but it's the same result each time. Tried using Kies to re-install the firmware but the phone doesn't stay on long enough for me to.
Is there anything I can try before giving it to Three for a month?
Thanks.
Click to expand...
Click to collapse
Maybe when u did the update, the file was corrupted. This could be happened if your internet connection was not stable.
So, to make sure u get the right update. Just download it from sammobile...u can find the right rom for your region...there.
After the download completed, just install it through odin. U can find how to use odin from internet. Just google it
Sent from my GT-N7000 using Tapatalk 2
Hi
Thanks for the replies, I downloaded and installed the firmware and I believe it all went well.
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7000XXLSZ_N7000XXLSO_N7000OXXLS4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.img
<ID:0/003> NAND Write Start!!
<ID:0/003> factoryfs.img
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> zImage
<ID:0/003> RQT_CLOSE !!
<ID:0/003> RES OK !!
<ID:0/003> Removed!!
<ID:0/003> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Unfortunately it still dies on boot. I'm thinking it could possibly be the battery?
Just to let you know I got a new battery and the phone is now fine.
Thanks for the help.
Hey guys need a little help here, i just bought a motherboard for my girlfriends s5, the old one seemed to overheated and died, yeah seriously. was just sitting on the bed.
I just spent $100 to get an AT&T Mobo, cracked open the phone and installed it. (The LCD is really thin, but to my suprise is really strong)
Stock Android 5.0 L, tried to to downgrade to 4.4.4, realize i cant now because of locked bootloader. trying to just restore back to Android 5 now.
Recovery mode presents " Firmware upgrade encountered an issue, Please select recovery mode in kies"
Download mode presents " SW Rev Check Fail : [aboot] fused > 4 Binary 3 "
I suppose this is because i flashed 4.4.2 in Odin the following
AP, CP, CSC
BL was NOT flashed!
Currently tried to find BL, AP, CP and CSC for 5.0 L, figure it would solve the problem
However my google-fuu leads me no awnsers, Closest thing i could find was.
theandroidsoul dot com /att-galaxy-s5-lollipop-update-odin-firmware-80652/
looks like it will flash 5.0 software, but.
My odin fails everytime i try, I have tried this on two computers, Windows 7 & 8
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> One Click Downloader Mode
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003>
<ID:0/003>
<ID:0/003>
<OSM> All threads completed. (succeed 0 / failed 1)
I really dont think its a driver issue., tried multiple cables.
Thanks
ok so we both have note 4s and i rooted both of our phones many months ago. i put poprocks v.13 on both phones and everything worked out fine. well over time that rom became outdated so i decided to update the phones. i updated mine to N910TUVU2EPE3_N910TTMB2EPE3_N910TUVU2EPE3_HOME.tar modem and the overdrive rom. had a few hick ups but over all went fine and my phone works great. so i decided to upgrade hers tonight. i put her phone into download mode and started odin. loaded the N910TUVU2EPE3_N910TTMB2EPE3_N910TUVU2EPE3_HOME.tar.md5 and hit start. well it failed and now the phone wont do anything. no matter what i do in odin it fails. ive tried cf-auto root it fails to. phone under download mode says blocked by r/l. odin usally stays stuck on setup connection. any ideas how to get this thing working again before she kills me?
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-trltetmo-trltetmo-smn910t.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> cache.img.ext4
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
Delete the .md5 and just leave it as .tar
<ID:0/003> Added!!
<ID:0/003> Odin engine v(ID:3.1101)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> recovery.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img.ext4
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
assuming you ment delete the md5 from the name of file. it didnt work.
just tried cf-root with odin on her laptop and same result. seems like this phone is a paperweight. im completely dumb founded. we have the exact same phones and i did hers the same way as mine. hers failed on the first step and now it looks like im buying her a new phone. this thing wont do anything at all. it can go into download mode but no matter what you try to load through odin fails.
osiris999 said:
just tried cf-root with odin on her laptop and same result. seems like this phone is a paperweight. im completely dumb founded. we have the exact same phones and i did hers the same way as mine. hers failed on the first step and now it looks like im buying her a new phone. this thing wont do anything at all. it can go into download mode but no matter what you try to load through odin fails.
Click to expand...
Click to collapse
Do you use hangouts (google) or Skype (chat)?
It seems it would be easier to help via one of those mediums.
osiris999 said:
just tried cf-root with odin on her laptop and same result. seems like this phone is a paperweight. im completely dumb founded. we have the exact same phones and i did hers the same way as mine. hers failed on the first step and now it looks like im buying her a new phone. this thing wont do anything at all. it can go into download mode but no matter what you try to load through odin fails.
Click to expand...
Click to collapse
Dupe
I was finally able to fix this thing using Samsung smart switch emergency recovery.
osiris999 said:
I was finally able to fix this thing using Samsung smart switch emergency recovery.
Click to expand...
Click to collapse
Glad you got it working. Looks like reactivation lock was turned on on hers but not yours. I always keep it off on my devices as I would forget to check.
Sent from my SM-N910T using XDA Free mobile app