hello xda developers
my friend came to me with his new galaxy s one phone to install Arabic firmware for him
well i tried home power voice down but it didn't go into download mode
then i tried power + home it went into download mode
after i start flashing using odin with 2.3.3 firmware I9000JPJV6_OJPJV6_JXJV6
odin failed to finish
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> cache.rfs
<ID:0/003> NAND Write Start!!
<ID:0/003> factoryfs.rfs
<ID:0/003> modem.bin
<ID:0/003> param.lfs
<ID:0/003> Sbl.bin
<ID:0/003> zImage
<ID:0/003> boot.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
and a message on the phone said invalid bootloader
later i knew that its not a normal galaxy s one
its anycall galaxy s and we don't have that version of galaxy S in my country so that's why i flashed the phone with out noticing that am flashing with normal S firmware
now the phone is completely died it don't go into download mode and no recovery mode nothing the phone is dead
is there any kind of solution for that or the phone need jtag box or smoothing ?
please help me because its the first time to face that kind of problem
lebknight said:
after i start flashing using odin with 2.3.3 firmware I9000JPJV6_OJPJV6_JXJV6
odin failed to finish
now the phone is completely died it don't go into download mode and no recovery mode nothing the phone is dead
is there any kind of solution for that or the phone need jtag box or smoothing ?
please help me because its the first time to face that kind of problem
Click to expand...
Click to collapse
1) All guides and Helpline for this model are in PIT STOP, link below
2) Flashing an SGS firmware on a Anycall SGS , will brick phone but recoverable by using Repair Kit found at PIT STOP
3) But since you say it is dead may be due to lack battery charge while flashing and rebooting (Try MY Android Solution link below for solution)
Related
So I tried updating to the newest Cyanogenmod Beta1 when it failed to boot repeatedly I went to reflash via Odin using stock JM9 with repartition 803.pit. This is what I got on Odin:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> modem.bin
<ID:0/004> modem.bin
<ID:0/004> Removed!!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
I had selected the modem and rom file that came with the samfirmware.com package.
Now phone will not even turn on, react to button presses, or show that it is charging while plugged in.. Tried taking out battery and putting it back in a few times with no luck.
This is an international version of the phone. Am I screwed? Could the battery have died while flashing or could the bootloader have been messed with?
I am panicing
Did you find a solution?
I have run into the identical issue and was wondering what your solution was?
I flashed the Vibrant firmware by accident onto my GT-i9000m and now the phone is dead, no boot screen, no logo, no reaction to any button combo.
I previously used the usb jig to get into the download mode, and when I reflashed a known to be good rom back on the phone I checked off "update bootloader" assuming the bootloader was at fault. Big mistake.
I've ordered a replacement phone from Bell, but if you have any info it would be greatly appreciated.
Thank you in advance.
p1010 dead!!
i tried to flash overcome kernel
there some pit error it said at odin
ahahahahahaha
but i manage to bring it up to life again lol
if anyone heres interested on making rom/kernel
i can be your tester.. ill be the one to take the risk
or can you teach me??
heres the error
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> zImage
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
sorry to hear that
try to flash to the original GTab wifi firmware ...
you can find it here ...
http://www.samfirmware.com/WEBPROTECT-p1010.htm
lol its working again ahahaha i manage it before i posted here
i want to know what is that error all about
thanks by the way
can you teach me how to flash the stock rom for the P1010???
my P1010 DEAD TOO!!!i try to use odin to flash the stock rom which i download from the samfirmware ,BUT , i DONT KNOW HOW TO FLASH IT..I SOLLOW THE GUIDE ON THE WEBSITE FOR P1000,BUT MY P1010 STILL BALCK DISPLAY after i flash it...HOW COME....HELP ME!
The P1010 nd P1000 are completely different (if I understood techno) right so don't follow those guides.
Sent from inside a whale.
Oh my god..then..what can i do..my p1010 cant open...it only stop at a black screen...
wo,i did it!I USE THE ODIN AND THE SAME METHOD TO FLASH BACK THE STOCK ROM!
where can i get a stock rom for the US WIFI version P1010? I messed up my Tab and now can no longer boot in.
This thread may help you flash back to stock.
Flashing Stock Rom
First of all I'm a beginner in android world .
Kernal: 2.6.32.9
[email protected] #1
The problem is:
I was trying to root my Galaxy S I9000 following the steps of [GUIDE] And then there was ROOT !
Everything was great until this step:
- Press "Start". ODIN you should now be flashing the kernel, and the device should reboot.
Odin gave me a red flag with " Failed " and I got this message:
<ID:0/009> Added!!
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> zImage
<ID:0/009> NAND Write Start!!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I unpulged my device and turned it off, when I turned it on a device-!- computer screen appered, after many tries I took off the battery and put it then I pressed the three combo button, finally I managed to get to download mode.
Now:
-My computer recognizes the device but Kies doesn't ( although it's the latest version and I tried to reinstall the drivers.)
-Odin keeps giving me the same error, and sometimes it stay stop at <ID:0/009> SetupConnection.. ( I tried XWKDD_insecure.tar & KE2_original.zip )
-I'm stuck in download mode.
Please help me get my phone to work (I prefer to return to the same firmware if it's possible).
https://www.wuala.com/Samsung Galax...and Odin/Original Firmwares/?key=AfzUZSU4SpKU
Download your original firmware from here and flash it in odin.
E: Btw are you using latest odin?
I got same problem when i m newb so calm down first go to www.samfirware.com and select ur phone download latest europen rom it is JVR and then flash them via odin by putting file respectively
Sent from my GT-I9000 using XDA App
i was rooted under 4.3 ML2, then i followed the second way(http://forum.xda-developers.com/showthread.php?t=2722073) to flash the pwnedkitkat.zip in safetrap, but my screen wasnt working so i searched forum and saw that it says reflash PDA from ML2, from http://forum.xda-developers.com/showthread.php?t=2721247 i did but it couldnt load up, so i wanted to reflash the BL for ML2, but instead i used the wrong one, i used the one called boot.tar.md5, which supposed to be PDA instead of BL, now i cant even boot up my phone.
ive done some research, and here are seems like where the problem from:
1: i cant recover it with safestrap installed.
2: the firmware on my phone is newer than the stock rom(ML2) im trying to flash.
im totally freaked right now, can somebody help me please, really really apreciate your help. (is there anyway i can get the ODIN files for 4.4.2? thanks thanks !!! compare with root, i need my phone first !!)
following is my odin log:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and on my phone screen it says
PRODUCT NAME : SGH-I537
CURRENT BINARY: Samsung Official
SYSTEM STATUS: CUSTOM
knox kernel lock: 0*0
knox warranty void: 0*1
csb-config-lsb:0*30
write protection: enable
ommc burst mode :enabled
start 224.1440
sw rev check fail: fused:4 binary:3
tqsdyy said:
i was rooted under 4.3 ML2, then i followed the second way(http://forum.xda-developers.com/showthread.php?t=2722073) to flash the pwnedkitkat.zip in safetrap, but my screen wasnt working so i searched forum and saw that it says reflash PDA from ML2, from http://forum.xda-developers.com/showthread.php?t=2721247 i did but it couldnt load up, so i wanted to reflash the BL for ML2, but instead i used the wrong one, i used the one called boot.tar.md5, which supposed to be PDA instead of BL, now i cant even boot up my phone.
ive done some research, and here are seems like where the problem from:
1: i cant recover it with safestrap installed.
2: the firmware on my phone is newer than the stock rom(ML2) im trying to flash.
im totally freaked right now, can somebody help me please, really really apreciate your help. (is there anyway i can get the ODIN files for 4.4.2? thanks thanks !!! compare with root, i need my phone first !!)
following is my odin log:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
and on my phone screen it says
PRODUCT NAME : SGH-I537
CURRENT BINARY: Samsung Official
SYSTEM STATUS: CUSTOM
knox kernel lock: 0*0
knox warranty void: 0*1
csb-config-lsb:0*30
write protection: enable
ommc burst mode :enabled
start 224.1440
sw rev check fail: fused:4 binary:3
Click to expand...
Click to collapse
I think your screen is deffective..? no other user has reported this issue
Sunderwear said:
I think your screen is deffective..? no other user has reported this issue
Click to expand...
Click to collapse
after many trials, i used boot.tar.md5 for BL and succesfully got back rooted on 4.3, however, i cant make phone calles, text messages are fine though, and hte screen, of course, works great . i rooted 4.3 then i followed your step for rooted 4.3 to 4.4.2 and i succefully installed it and the touch screen is not reponding, not at all, but only with one touch to unlock it, and after unlock, i cant do nothing. and most of the time i cant even unlock it. i am fine with rooted 4.3 or unrooted whatever, i jsut need a phone badly... please help me. when i try to make a phone call, after i pressed "call" nothing happens, the phone froze, yet people im dialing can receive the phone call, just that they cnat hear me.
(im not sure if this is a stupid question , but will there be an ODIN restore for 4.4.2? if yes, how long will it be released? i think the fact i cant make phone calls actually contributed by the wrong bootloader, (or i might be wrong). thanks a lot man, i know you're great! really appreaciate your work on rooting 4.3)
HI friends
I have note 5 duos SM-9208 brought in Taiwan, Its completely official with latest updates running on 6.1 marshmallow
I want to have just TWRP recovery on my phone no rooting for now, as i want to have my official stock rom backup as soon as i get twrp on my phone, later i can go for rooting
did oem unlock, usb debug on , connected on download mode and tried to flash twrp file (twrp-3.0.2-1-nobleltezt.img.tar)
the box turned green but no pass and then i get blue screen with white exclamation mark screen and chinese text on it ( i.imgsafe.org/ce3bada933 .jpg) remove space before .jpg
guide i used stechguide.com/install-twrp-recovery-on-samsung-galaxy-note-5
nothing happens in ODIN too it says RQT close!!
<ID:0/007> Added!!
<ID:0/007> Removed!!
<ID:0/007> Added!!
<ID:0/007> Removed!!
<ID:0/007> Added!!
<ID:0/007> Removed!!
<ID:0/010> Added!!
<ID:0/010> Odin engine v(ID:3.1203)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> SingleDownload.
<ID:0/010> recovery.img
<ID:0/010> RQT_CLOSE !!
I don't understand whats happening with that blue screen as everything is in chinese,
it didnt work as explained in that link, please help me guys any guys from taiwan if they can explain what it says and how to install twrp successfully here
thanks
..
Got the same problem after latest update of my note 5 SM-N9208 from Philippines.
yogiexp said:
blue screen error with chinese text i.imgsafe.org/ce3bada933 .jpg
guide i used stechguide.com/install-twrp-recovery-on-samsung-galaxy-note-5
Click to expand...
Click to collapse
Tried it but doesn't work.
yogiexp said:
HI friends
I have note 5 duos SM-9208 brought in Taiwan, Its completely official with latest updates running on 6.1 marshmallow
I want to have just TWRP recovery on my phone no rooting for now, as i want to have my official stock rom backup as soon as i get twrp on my phone, later i can go for rooting
did oem unlock, usb debug on , connected on download mode and tried to flash twrp file (twrp-3.0.2-1-nobleltezt.img.tar)
the box turned green but no pass and then i get blue screen with white exclamation mark screen and chinese text on it
nothing happens in ODIN too it says RQT close!!
<ID:0/007> Added!!
<ID:0/007> Removed!!
<ID:0/007> Added!!
<ID:0/007> Removed!!
<ID:0/007> Added!!
<ID:0/007> Removed!!
<ID:0/010> Added!!
<ID:0/010> Odin engine v(ID:3.1203)..
<ID:0/010> File analysis..
<ID:0/010> SetupConnection..
<ID:0/010> Initialzation..
<ID:0/010> Get PIT for mapping..
<ID:0/010> Firmware update start..
<ID:0/010> SingleDownload.
<ID:0/010> recovery.img
<ID:0/010> RQT_CLOSE !!
I don't understand whats happening with that blue screen as everything is in chinese,
it didnt work as explained in that link, please help me guys any guys from taiwan if they can explain what it says and how to install twrp successfully here
thanks
Click to expand...
Click to collapse
Just found a way to get TWRP back on my note 5.
I flashed with odin the Chainfire autoroot Auto-Root-noblelte-nobleltextc-smn9208.tar.md5
Your phone will get stuck on boot screen and it will say in left upper corner "seandroid not enforcing".
Push volume down + home + on/off, to get back in download mode.
Flash with odin the TWRP file.
Now you will have working TWRP (i rooted my phone directly)
It worked for me, let me know if it worked for you.
Regards,
Pr4d0
Did you run the CROM Service app to unlock the bootloader? You will not be able to flash anything until you unlock the bootloader. My girlfriend has the same phone and you are in luck that I still have the CROM Service app, you can download load it from here
https://1drv.ms/u/s!AumjSD0UEAABgpkxvUZZgxs0UAum5g
dhonzik said:
Did you run the CROM Service app to unlock the bootloader? You will not be able to flash anything until you unlock the bootloader. My girlfriend has the same phone and you are in luck that I still have the CROM Service app, you can download load it from here
https://1drv.ms/u/s!AumjSD0UEAABgpkxvUZZgxs0UAum5g
Click to expand...
Click to collapse
thanks i think its the issue with crom unlock, but i see warning everywhere it will knockout knox! i was trying to have twrp without rooting or disable knox, but i guess i dont have choice with my model.