I'm currently on jellycore (hydracore kernel), I download the ICS rom below and tried to flash it via CWM. I wiped cache/dalvik and installed from SD, everything seemed to go ok but now the phone will only boot to the samsung logo.
http://forum.xda-developers.com/showthread.php?t=1872965
Do you think I should try and install an older ROM like gingerbread via PC-Odin ?
Thanks,
mug2k said:
I'm currently on jellycore (hydracore kernel), I download the ICS rom below and tried to flash it via CWM. I wiped cache/dalvik and installed from SD, everything seemed to go ok but now the phone will only boot to the samsung logo.
http://forum.xda-developers.com/showthread.php?t=1872965
Do you think I should try and install an older ROM like gingerbread via PC-Odin ?
Thanks,
Click to expand...
Click to collapse
Why did you only wipe cache and dalvik? You should've wiped data as well. Boot back into Recovery. Flash the Hydracore kernel (if you don't have that, flash the Jellycore ROM because it has the kernel). Reboot recovery. Wipe data, cache and dalvik. Flash stock ICS again. Boot.
andreww88 said:
Why did you only wipe cache and dalvik? You should've wiped data as well. Boot back into Recovery. Flash the Hydracore kernel (if you don't have that, flash the Jellycore ROM because it has the kernel). Reboot recovery. Wipe data, cache and dalvik. Flash stock ICS again. Boot.
Click to expand...
Click to collapse
I'm currently in download mode because I was going to install GB via PC-Odin. Can I just turn off the phone ?. Also is the ROM in the OP ok to flash once I've re-flashed hydracore ?.
mug2k said:
I'm currently in download mode because I was going to install GB via PC-Odin. Can I just turn off the phone ?. Also is the ROM in the OP ok to flash once I've re-flashed hydracore ?.
Click to expand...
Click to collapse
It should give you an option to reboot in download. But you can just hold down volume up + power + home button and restart to recovery.
After you re-flash Hydracore AND REBOOT RECOVERY, you can flash whatever stock ICS you want, just make sure you wipe data, cache and dalvik.
DO NOT WIPE DATA BEFORE YOU REBOOT RECOVERY! Can't stress enough.
andreww88 said:
It should give you an option to reboot in download. But you can just hold down volume up + power + home button and restart to recovery.
After you re-flash Hydracore AND REBOOT RECOVERY, you can flash whatever stock ICS you want, just make sure you wipe data, cache and dalvik.
DO NOT WIPE DATA BEFORE YOU REBOOT RECOVERY! Can't stress enough.
Click to expand...
Click to collapse
Just to be 100% sure, wipe data, cache and dalvik AFTER I've flashed hydracore, rebooted recovery and flashed stock ICS.
mug2k said:
Just to be 100% sure, wipe data, cache and dalvik AFTER I've flashed hydracore, rebooted recovery and flashed stock ICS.
Click to expand...
Click to collapse
You can flash hydracore, reboot recovery, wipe data, cache and dalvik, then flash stock ICS.
Still stuck on the samsung logo, must be something wrong with the ROM I have.
edit: its ok, just took a while
mug2k said:
Still stuck on the samsung logo, must be something wrong with the ROM I have.
edit: its ok, just took a while
Click to expand...
Click to collapse
Good.
It does take longer to boot the first time, especially on TW roms.
andreww88 said:
Good.
It does take longer to boot the first time, especially on TW roms.
Click to expand...
Click to collapse
Appreciate the help dude, got a bit scared for a while. Thought I bricked it
Related
a) coming from a rooted GB-ROM:
- download Abyss Kernel 4.2 from here: http://www.mediafire.com/?c65mndvpk6ocbaa
- put zip-file on your USB-storage
- boot in Recovery
- Flash Abyss Kernel 4.2!!!
- boot back in recovery (you find this option under 'advanced')
- FullWipe
- Flash ROM
- reboot system
- ...you are done
==> there have been reported problems with a constantly rebooting system when doing installation coming from a GB-ROM as posted above! So the safe and 100% successful way is installing LPY Stock-ROM, root Stock ROM and then go on as described below under point b2). Do not ask for a tutorial on how to install and root LPY Stock ROM....it is describe enough here in Forum!
Click to expand...
Click to collapse
I would like to flash Charck's ICS XXLPY V4 because of simple ROM.
But I do not understand "Fullwipe" in the instruction.
Is there the exact menu "Fullwipe" after flashing Abyss Kernel4.2?
Or I have to click all wipe menu? (there are two wipe menu...)
And I would like to try to flash this ROM without the installation of LPY Stock-ROM.
Is there anyone who succeed this way?
rapboy75 said:
I would like to flash Charck's ICS XXLPY V4 because of simple ROM.
But I do not understand "Fullwipe" in the instruction.
Is there the exact menu "Fullwipe" after flashing Abyss Kernel4.2?
Or I have to click all wipe menu? (there are two wipe menu...)
And I would like to try to flash this ROM without the installation of LPY Stock-ROM.
Is there anyone who succeed this way?
Click to expand...
Click to collapse
Full wipe = data/factory reset + wipe cache + wipe dalvik cache (in advanced).
Already Rooted
gee2012 said:
Full wipe = data/factory reset + wipe cache + wipe dalvik cache (in advanced).
Are you allready rooted or not?
Click to expand...
Click to collapse
Thanks for your advice!!!
My phone is already rooted now. and also I already installed Abyss Kernel 4.2, too.
I just confused if "FullWipe" is one of the exact menu or meaning of wiping menus.
I will give a try right away!
rapboy75 said:
Thanks for your advice!!!
My phone is already rooted now. and also I already installed Abyss Kernel 4.2, too.
I just confused if "FullWipe" is one of the exact menu or meaning of wiping menus.
I will give a try right away!
Click to expand...
Click to collapse
"FullWipe" is not one of the exact menu. Go to wiping menus, you need to do all three separately: wipe data/factory reset, wipe cache, then wipe dalvik cache.
rapboy75 said:
I would like to flash Charck's ICS XXLPY V4 because of simple ROM.
But I do not understand "Fullwipe" in the instruction.
Is there the exact menu "Fullwipe" after flashing Abyss Kernel4.2?
Or I have to click all wipe menu? (there are two wipe menu...)
And I would like to try to flash this ROM without the installation of LPY Stock-ROM.
Is there anyone who succeed this way?
Click to expand...
Click to collapse
i can't flash Abyss Kernel4.2 i don't know what happen to my SGN it was Working Good And When i Try To Flash Rocket Rom v7 ICS i want to make full wipe i try to install Abyss Kernel4.2 but when i reboot my phone i found clock work mode v5.8.1.8 i don't know what happens i try to flash my mobile using pc odin done and when i try to flash abyss i can't i don't know why can anyone help me plz
mhmoud2000 said:
i can't flash Abyss Kernel4.2 i don't know what happen to my SGN it was Working Good And When i Try To Flash Rocket Rom v7 ICS i want to make full wipe i try to install Abyss Kernel4.2 but when i reboot my phone i found clock work mode v5.8.1.8 i don't know what happens i try to flash my mobile using pc odin done and when i try to flash abyss i can't i don't know why can anyone help me plz
Click to expand...
Click to collapse
Hi,after flash abyss kernel pls go to advanced.menu and reboot recovery.hope this help.
Sent from my GT-N7000 using xda premium
If you can get into recovery
1: Flash abyss kernel from SD card
2: Press go back>advanced>reboot in recovery
3: Wipe data
4: Wipe cache
5: Goto advanced and wipe dalvik cache
6: Install the rom (eg rocket rom) from SD card
7: Press go back and reboot device
maionline said:
If you can get into recovery
1: Flash abyss kernel from SD card
2: Press go back>advanced>reboot in recovery
3: Wipe data
4: Wipe cache
5: Goto advanced and wipe dalvik cache
6: Install the rom (eg rocket rom) from SD card
7: Press go back and reboot device
Click to expand...
Click to collapse
i can't flash any custom rom
i try to flash abyss using kernel LQ2 but when i try my device load for like 5 min and then reboot without flashing i don't know what i can do i need someone online to told me what i can do exactly plz xda users help me i make something wrong with my mobile my email [email protected] i need someone to be with me step by step plz all
with LQ2 Kernel i can flash anything the device load for 5 min and then reboot without doing anything
i will try to back to GB rooted stock Rom using pc odin
i got error when i try to update throuhg recovery E:signature verification failed
Is it safe to backup and restore roms using abyss kernel?
Advice please...stuck at bootscreen! (followed instructions in crash thread s follows
1. Was on rocket rom v10 with notecore.
2. Flashed abyss
3. 3 wipes + JBroid cleaner
4. Flashed crash 8.2
5. Rebooted
6. Stuck on 'galaxy note' boot screen, tried rebooting. Still stuck. (waited over 10 minutes)
Advice please!!
Did you try booting to recovery and flashing again? Or try clearing cache and delvik cache.
barretp said:
Did you try booting to recovery and flashing again? Or try clearing cache and delvik cache.
Click to expand...
Click to collapse
Yes, tried booting into recovery and wiping again, didn't work. Tried reflashing, still stuck. Tried flashing a different kernel, still stuck.
What's going on?!
Edit: I'm suspecting JBroid might be the issue here..have flashed in the past with no problem but this time decided to use JBroid (as advised in crash thread)..
When you say wiping, do you mean factory reset or wiping cache? If those didn't work flash a stable CM9 kernel, reboot in recovery, and then try to flash again.
barretp said:
When you say wiping, do you mean factory reset or wiping cache? If those didn't work flash a stable CM9 kernel, reboot in recovery, and then try to flash again.
Click to expand...
Click to collapse
Tried both. First just wiping cache/dalvik, then just doing factory reset (after installing notecore because of mmc_erase bug). Neither worked! The only kernels I have on my sd are notecore, abyss. Running out of options..may just try flasing rocket rom again..
octavian90 said:
Tried both. First just wiping cache/dalvik, then just doing factory reset (after installing notecore because of mmc_erase bug). Neither worked! The only kernels I have on my sd are notecore, abyss. Running out of options..may just try flasing rocket rom again..
Click to expand...
Click to collapse
Try flashing a pre rooted stock GB firmware and see if you get the phone to work. Then, try flashing from there.
glevitan said:
Try flashing a pre rooted stock GB firmware and see if you get the phone to work. Then, try flashing from there.
Click to expand...
Click to collapse
Flashed back to RR v10 without any problems. Not sure why Crash wouldn't install but that was quite a scare!
octavian90 said:
Flashed back to RR v10 without any problems. Not sure why Crash wouldn't install but that was quite a scare!
Click to expand...
Click to collapse
glad you have your phone back. Maybe a bad download?
Sent from my GT-N7000 using xda app-developers app
Really digging the positive advice from everyone, thanks! It was a bad download. Downloaded again and flashed just fine =D.
Sent from my GT-N7000 using Tapatalk 2
currently on alliancerom, just wonder if it possible to directly flash ICS back via ODIN or i MUST go back to GB first?
you can flash directly to ICS, you may get some FCs after the flash because of old custom ROM files, So the best thing to do would be to:
Reboot into TWRP recovery (included with Alliance ROM)
wipe cache / dalvik cache / factory reset
reboot download mode
flash ICS via ODIN or Mobile ODIN.
azzledazzle said:
you can flash directly to ICS, you may get some FCs after the flash because of old custom ROM files, So the best thing to do would be to:
Reboot into TWRP recovery (included with Alliance ROM)
wipe cache / dalvik cache / factory reset
reboot download mode
flash ICS via ODIN or Mobile ODIN.
Click to expand...
Click to collapse
i wonder is it safe to flash philz kernel and reboot recovery into cwm and flash other rom? because as far as i know flashing cwm type of zip will cause big issue in twrp
sure you can, just download it and install like you would a ROM, It might not work with Alliance ROM, so be sure to reboot recovery and change ROM from there. :good:
whitepandaaa said:
i wonder is it safe to flash philz kernel and reboot recovery into cwm and flash other rom? because as far as i know flashing cwm type of zip will cause big issue in twrp
Click to expand...
Click to collapse
You can flash Stock ICS and philz kernel at the same time with Mobile Odin. Then, reboot in recovery and do the wipes....that is how I did it and worked fine for me.
Hey,
I got little problem and I need some help. I wanted to falsh OMNI AsylumKANG (from thread http://forum.xda-developers.com/showthread.php?t=2591479 ) , but my n7000 failed to start system. Instead after samsung logo it restarted into twrp screen.My version number is N7000XXLT9. These are steps I made:
1. using stock recovery I flashed PhilZ-cwm6-XXLT9-ORA-5.11.2-signed
2. then launched and rebooted into PhilZ recovery
3. flashed raw_kernel_r4_j43 and reboot into recovery
4. wiped data, cache partition and dalvik cache
7. flashed AsylumKANG_4.4.2_n7000_Build2.2
8. flashed pa_gapps-modular-mini-4.4.2-20140111-signed
9. flashed UPDATE-SuperSU-v1.86
10. reboot
Afterwards as I said phoned showed samsung logo and rebooted itself to twrp recovery
What is problem here?
Thanks for help.
Should reflash Philz. Go to wipe/factory reset menu, then choose clean to install rom. Then go to advanced, wipe dalvik cache. Then reflash raw5, then flask rom.
Sent from my phone.
forest1971 said:
Should reflash Philz. Go to wipe/factory reset menu, then choose clean to install rom. Then go to advanced, wipe dalvik cache. Then reflash raw5, then flask rom.
Sent from my phone.
Click to expand...
Click to collapse
Thanks for idea but I didn't help I flashed stock rom, then Philz then clean to install rom, wipe dalvik cache and the rest is just like from step 3 down. Same issue. I flashed once again stock rom and Philz, but this time installed paranoid android 3+ (pa_n7000-3.99-RC2-20131012). It worked. Maybe I just wait for more kitkat 4.4 based rom releases and then try.
After flash r5 you need to boot into recovery before proceed with lashing rom. Make sure you have done that step.
Sent from my phone.
forest1971 said:
After flash r5 you need to boot into recovery before proceed with lashing rom. Make sure you have done that step.
Sent from my phone.
Click to expand...
Click to collapse
After flash r4 i boot into recovery. You're saying to flash r5 instead of r4?
After installing latest cm11 my phone cant boot into recovery. Or cant boot the rom, even the boot logo of cm doesnt show up.
What i did before;
-Wiped system/cache/data (all f2fs)
-Flashed the latest cm11
-Wiped dalvik cache and boot
-After doing first config. Realized i didnt flash gapps
-Boot into recovery wipe system/data/cache
-Flash rom again, and latest pa gapps, wipe dalvik
-Boom, phone wont boot and cant get boot into recovery.
Tried flashing twrp via odin, latest cm11 with odin and neither of them worked. Can someone help me, please? Thank you.
heithered said:
After installing latest cm11 my phone cant boot into recovery. Or cant boot the rom, even the boot logo of cm doesnt show up.
What i did before;
-Wiped system/cache/data (all f2fs)
-Flashed the latest cm11
-Wiped dalvik cache and boot
-After doing first config. Realized i didnt flash gapps
-Boot into recovery wipe system/data/cache
-Flash rom again, and latest pa gapps, wipe dalvik
-Boom, phone wont boot and cant get boot into recovery.
Tried flashing twrp via odin, latest cm11 with odin and neither of them worked. Can someone help me, please? Thank you.
Click to expand...
Click to collapse
You wiped the system right? So you fkd up your phone. Never wipe the system.
mauam said:
You wiped the system right? So you fkd up your phone. Never wipe the system.
Click to expand...
Click to collapse
Whats wrong with wiping system before flashing a rom?
heithered said:
Whats wrong with wiping system before flashing a rom?
Click to expand...
Click to collapse
Don't know, I only remember a old advice from an old friend here, that's it. I never wiped the system, though. Good luck bud