Related
Hi there,
i was trying to flash my samsung galaxy s and put darky's on it but for some reason i can't.
The recovery screen that pops op says recovery 3e (and every tutorial i found said 2e),
i try to "apply sdcard:update.zip
(i downloaded the update file from the darky roms thread)
and i get the error: failed to verify whole-file signature
signature verification failed, installation aborted.
i've got a samsung galaxy I9000XWJPA.
I've flashed the phone using z4root.
Then i've checked with terminal emulator that it's rooted.
I think that there's a problem with clockwork, or that i just didn't install that correctly, so i'm kinda stuck at the moment :s
could someone please help me?
First of all you should get the busybox file and flash it. Then copy the update.zip into the internal sd card and copy the darky rom too.
Before doing this i would restore it to factory settings. Dont root it with z4root, the busybox roots it and it allows you to open the update.zip
Try what i said and it should work.
Sent from my GT-I9000 using Tapatalk
You are on Android 2.2 which has the 3e recovery. 3e recovery doesn't allow using unsigned .zip files. You should first downgrade your recovery to 2e by flashing CF-root. After you downgrade your recovery, you'll be able to use any update.zip file.
You can find CF-root in this link:
http://forum.xda-developers.com/showthread.php?t=788108
Since you have XWJPA, you should download the JPA version from the second post. Instructions are in the first post.
Make sure you have 3-button recovery and download modes working before flashing.
oh that's via odin3 right?
i'll try that, thanks
Tell us if there's any problem.
Sent from my GT-I9000 using Tapatalk
hmm, i've followed all the steps, downloaded odin, and the CF-Root-XW_XEE_JPA-v1.2-Busybox-1.17.1.tar file, but the download screen only says "downloading, do not turn off target!!!
is there any particular setting or where to place the .tar file?
mavu said:
hmm, i've followed all the steps, downloaded odin, and the CF-Root-XW_XEE_JPA-v1.2-Busybox-1.17.1.tar file, but the download screen only says "downloading, do not turn off target!!!
is there any particular setting or where to place the .tar file?
Click to expand...
Click to collapse
Ok.
First of all disconnect the galaxy from the pc. Close odin. Open Odin, put in PDA CF-Root-XW_XEE_JPA-v1.2-Busybox-1.17.1.tar
Then shut down the galaxy. Reboot it again to download mode. Connect it via usb and then click start. Make sure re-partition isn't checked.
That's it. When setting up odin you can't have the galaxy connected to he computer. If something fails on download mode, you must always restart the download mode or it'll be stuck.
Good luck
aha, found the problem:
there doesn't appear a comport in odin
new problem, how do i get the phone recognized?
mavu said:
aha, found the problem:
there doesn't appear a comport in odin
new problem, how do i get the phone recognized?
Click to expand...
Click to collapse
It should recognize it when you connect it in download mode...
Mine recognizes it as COM4.
This may be simple, but restart your computer and phone and see if it works.
mavu said:
aha, found the problem:
there doesn't appear a comport in odin
new problem, how do i get the phone recognized?
Click to expand...
Click to collapse
It should recognize it when you connect it in download mode...
Mine recognizes it as COM4.
This may be simple, but restart your computer and phone and see if it works.
If not, re-install the drivers for your phone
hi mate i had exactly the same problems as you and it done my head in for about a day and a half but then someone gave me this advice and it worked a treat,
go to market
download sgs kernel
once done flash speedmod kernel using the app
re start phone
once done download darkys rom
reboot to download mode (should now have 2e)
flash zip
choose zip
find darkys
click yes instal darkys
job done
one thing i must point out in 2e is the back button on your phone is now the select button and the menu button on the bottom left is now your back button
hope this helps as it did for me
Restart your pc and make sure Kies is not working at all.
thanks man! reinstalling the drivers did the trick ten points for coldflid!!!
steve57925 said:
go to market
download sgs kernel
once done flash speedmod kernel using the app
re start phone
once done download darkys rom
reboot to download mode (should now have 2e)
flash zip
choose zip
find darkys
click yes instal darkys
job done
Click to expand...
Click to collapse
For the record, people do NOT have to flash Darkys or any other custom ROM to get 2e. Simply flashing a kernel that has Clockwork Recovery included will do the trick. Your reco to flash SpeedMod would have solved the problem without having to go further.
Very true but he wanted darkys which was the only reason I mentioned but good to point out for others reading the post
Sent from my GT-I9000 using XDA App
mavu said:
thanks man! reinstalling the drivers did the trick ten points for coldflid!!!
Click to expand...
Click to collapse
Im happy ir worked =]
Sent from my GT-I9000 using Tapatalk
steve57925 said:
Very true but he wanted darkys which was the only reason I mentioned but good to point out for others reading the post
Sent from my GT-I9000 using XDA App
Click to expand...
Click to collapse
You're 100% correct - my mistake for missing it on the first go-around.
not a problem
Hello ,
I have a similar problem with my Galaxy S I9000 .
I've updated it via KIES to the latest Froyo ( 2.2 as it shows my phone ) .
Next , I tried to install the voodoo lagfix .
I downloaded the .zip file and renamed it to "update.zip" .
Then I copied it to my phone's sd card ( I connect to PC via usb and copied in the 'Phone' folder ) .
Next , I used the 3 buttons ( Volume UP + middle button + turn off button ) and it got into Recovery mode .
I selected the 'update.zip' file and accesed it , but it says :
"E: signature verification failed, installation aborted."
I have to downgrade to 2E first ?
Official Rom from LG - v30a!!!!
This release is the same that is from 7.12.12!!!!!
---------------------------------------------------------------------------------------
links for download:
official link from lg (kdz version)
http://csmg.lgmobile.com/swdata/WEBSW/LGP990/ANEUDW/V30a_00/V30A_00.kdz
Smartflash version of the Rom
http://file.qip.ru/get/EpX_YlZ5/BIN_LGP990AT-00-V30a-EUR-XXX-N.html
mirrors:
http://www.multiupload.nl/Z4413CU6XN (thanks to sander-m)
http://www.putlocker.com/file/28C0DF5FDD929E34 (thanks to tiagorl)
Ril http://www.multiupload.nl/2764GZ1F8Q
BB http://www.multiupload.nl/0C893V659X (thanks to cojo11)
---------------------------------------------------------------------------------------
You are going to download zipped file. This The download contains the following files: (thanks to petr.klos)
LGP990AT-00-V30a-EUR-XXX-NOV-30-2012+0_AP.bin
LGP990AT-00-V30a-EUR-XXX-NOV-30-2012+0_CP.fls
---------------------------------------------------------------------------------------
For flash use Smartflash
Smartflash tutorial by PAUL (thanks to petr.klos)
I would just add, that this thread is focused on flashing sole baseband. To flash firmware (ROM) you have to add one single step.
Where is
"--Click the browse button next to 'CP Bin:' and select the baseband (FLS) file--"
you add
"--Click the browse button next to 'AP Bin:' and select the firmware (BIN) file--"
For those who get errors while flashing, this is what always fixes issues for me: (thanks to Custom40)
1) Reboot PC and just start over.
Or:
2) If you face an error in the middle of the installation, then re-plug the phone, start over but this time put the AP file in the CP bin box and the CP file in AP box.
---------------------------------------------------------------------------------------
-=How to get root=-
=1= (thanks gabrielecif)
To get root easy (no data wipe and original bootloader) go to these thread:
http://forum.xda-developers.com/showthread.php?p=35138820#post35138820
=2= (thanks to RobYyY)
UNLOCKED BOOTLOADER+CWM6+ROOT
o2x-nvflash-bootloader_unlock_v30a+CWM6.zip
♦unzip attached archive
♦put your phone into nvflash mode(don't know how? use search button)
♦open "flash-boot.bat"
♦put again your phone into nvflash mode
♦open "cwm.bat"
♦boot into cwm and flash SuperSU Root.zip
♦reboot and enjoy
EDIT1: Root doesn't work with su303.zip i don't know why.. but i have made a zip with supersu and root is working. have fun(supersuroot.zip is attached)
=3= (thanks to joiN85)
-After you install with smartflash v30a rom, download and flash "Bootloader unlock ICS Official" and "Recovery 5.0.2.8e v30a Official"
-Flash with NVFlash: Recovery 5.0.2.8e v30a Official + Bootloader unlock ICS Official
-Go in cwm and install "Superuser-3.1.3-arm-signed-tradotto.zip"
-Reboot
-Now you have Root
IMPORTANT!!!
Some users have charging problems (while connect your phone to charge with screen on - it breaks)
It is becouse of root in some case, without root everything is ok. Need more fredbacks for this!
Credits to Daniel Aminov, he received the link (smartflash version from 4.12.12).
wow. hope this is real.. can't wait to test
Yeah, i hope so too) Now i must go and I'll return in the evening, and downloading the firmware will be finished i think. Then I'll be able to say exactly.
It looks like that it comes from anonymous.
Gesendet von meinem Optimus 2X mit Tapatalk 2
URL from Leaker doesn't say error 404 anymore for me, but still can't download KDZ file :fingers-crossed:
sander-m said:
OK, new mirror for those who want stable/fast download (mirror by google);
http://goo.gl/RDqeW
Click to expand...
Click to collapse
File contains:
Code:
LGP990AT-00-v30a-EUR-XXX-NOV-30-2012+0_AP.bin 01.12.2012 00:02:38
LGP990AT-00-v30a-EUR-XXX-NOV-30-2012+0_CP.fls 30.11.2012 22:14:06
Could anyone who downloaded it, put it onto some other fileshare? (Kindly please)
Was at it myself but only downloaded 45 MBs then it crashed.
By my WinRAR, it contains
LGP990AT-00-V30a-EUR-XXX-NOV-30-2012+0_AP.bin
uncompressed filesize 1 018 167 296 B
and probably CP, which I cannot confirm, since my download failed and I can't w8 for another 12 minutes to redownload it. Worksh[ee]t.
downloading now. hope its real and genuine...for me, the leaker still says not found
donwloading
Downloading...
downloading 20 min left
The download contains the following files:
LGP990AT-00-V30a-EUR-XXX-NOV-30-2012+0_AP.bin
LGP990AT-00-V30a-EUR-XXX-NOV-30-2012+0_CP.fls
I will see if I can upload to a mirror.
Who got the baseband for this 30a?
Finally waiting to get back home n try this........
Shadowchaz said:
The download contains the following files:
LGP990AT-00-V30a-EUR-XXX-NOV-30-2012+0_AP.bin
LGP990AT-00-V30a-EUR-XXX-NOV-30-2012+0_CP.fls
I will see if I can upload to a mirror.
Click to expand...
Click to collapse
Can u confirm whether its genuine and can u gives all some more details after installing. I probably wud've done it if i had downloaded it... And thanks a million for mirroring it...waiting for the link...
orbital_71 said:
Who got the baseband for this 30a?
Click to expand...
Click to collapse
Correct me if I am wrong but Isn't the baseband just the fls file in the zip?
naazgulla said:
Can u confirm whether its genuine and can u gives all some more details after installing. I probably wud've done it if i had downloaded it... And thanks a million for mirroring it...waiting for the link...
Click to expand...
Click to collapse
Trying to upload to my dropbox, but the upload keeps failing
rxformula91 said:
Correct me if I am wrong but Isn't the baseband just the fls file in the zip?
Click to expand...
Click to collapse
We cannot correct you, since you in fact are correct.
rxformula91 said:
Correct me if I am wrong but Isn't the baseband just the fls file in the zip?
Click to expand...
Click to collapse
I just want BB
Thanks for sharing this,
I've completed the download, currently smartflashing it to my O2X.
I'm also uploading it right now to other filehosting services.
I will report back soon. Maybe this is the real deal.
Edit:
Mirror:
http://www.multiupload.nl/Z4413CU6XN
Smartflash error occured . Maybe it's just a fake or whatever. Device is still at v28G.
Flashing.....
i installed emanoN rom v7 a few months and reverting back to stock rom downloaded from samfirmware.com for some reasons
now i again flashed cyanogenmod 10.1 by rohan007(no doubt, its a great rom) :good: about a week ago
but it is too much for my mini to handle that....ram usage is always above 200 mb(why its said that mini has 384 mb ram while we get only 280 )
so i want to revert back to that stock rom which i dowloaded
but when i try to install from sd card-->choose file-->s5570ddkq7_ddkq6_INU
i get something like
e:/s5570_ddkq6_inu
(bad)
Installation aborted
WHY :crying: it worked earlier
PS: i tried from different microSD cards and copied for around 3 times to the microsd card
This will fix your problem (guides aren't mine)
Guide http://forum.xda-developers.com/showthread.php?t=1255305
Another good guide: http://forum.xda-developers.com/showthread.php?t=1551586
To root use "universal gingerbread root v.2.5"
I've tested with XWKTN ROM and all works fine.
Btw, test "chocobread" or "democracy" ROM's. Inmo they are good looking with good performance.
jeremypt said:
This will fix your problem (guides aren't mine)
Guide http://forum.xda-developers.com/showthread.php?t=1255305
Another good guide: http://forum.xda-developers.com/showthread.php?t=1551586
To root use "universal gingerbread root v.2.5"
I've tested with XWKTN ROM and all works fine.
Btw, test "chocobread" or "democracy" ROM's. Inmo they are good looking with good performance.
Click to expand...
Click to collapse
okk i got that...but do i need to download it again? (i am already past usage limit)
i have the file in .zip format which worked earlier through update from sd card in recovery mode
Galaxy_Addict said:
okk i got that...but do i need to download it again? (i am already past usage limit)
i have the file in .zip format which worked earlier through update from sd card in recovery mode
Click to expand...
Click to collapse
Open the ZIP (extract) in your computer. If you have 4 md5 files you need to flash using the 4 files method
If you have only 1 md5 file you need to flash using the 1 file method.
This is how you flash stock firmware, modded is flashed from SDcard using CWM.
jeremypt said:
Open the ZIP (extract) in your computer. If you have 4 md5 files you need to flash using the 4 files method
If you have only 1 md5 file you need to flash using the 1 file method.
This is how you flash stock firmware, modded is flashed from SDcard using CWM.
Click to expand...
Click to collapse
thanks mate for the info...there is a single .md5 file so i tried to flash using odin...but that odin is not detecting my phone
i think that my pc has all the drivers installed in it because i have the latest kies and usb mass storage,and usb tethering are working fine
odin worked when i first flashed my rom (emanoN v7)...but now its not working
any other alternatives please..!!!
you need to put the phone in download mode.
With the phone OFF, hold "volume down" + "power" + "home" untill you see the "download mode" screen.
Galaxy_Addict said:
thanks mate for the info...there is a single .md5 file so i tried to flash using odin...but that odin is not detecting my phone
i think that my pc has all the drivers installed in it because i have the latest kies and usb mass storage,and usb tethering are working fine
odin worked when i first flashed my rom (emanoN v7)...but now its not working
any other alternatives please..!!!
Click to expand...
Click to collapse
Just remove any model name from ops file & then place it in OPS field.
Remember, odin detects ur phone through the ops file..., no matter whether it's physically connected to pc or not (at that instant).
Disable kies b4 Starting.
Sent Via XDA™ Premium
jeremypt said:
you need to put the phone in download mode.
With the phone OFF, hold "volume down" + "power" + "home" untill you see the "download mode" screen.
Click to expand...
Click to collapse
i know that bro...i am not that much of a noob
Galaxy_Rohit said:
Just remove any model name from ops file & then place it in OPS field.
Remember, odin detects ur phone through the ops file..., no matter whether it's physically connected to pc or not (at that instant).
Disable kies b4 Starting.
Sent Via XDA™ Premium
Click to expand...
Click to collapse
so do i need to rename the file from tass.ops to what?
not a noob
how will you flash a tar file with cwm and you said you were successful last time
ops's name must be TASS.ops
dheeraj (dhlalit11) said:
not a noob
how will you flash a tar file with cwm and you said you were successful last time
ops's name must be TASS.ops
Click to expand...
Click to collapse
when did i say that i flashed a tar file using cwm....i flashed the .zip file using cwm
does usb debugging has anything to do with this..?
can you tell which firmware comes in zipped file
either the firmware would be tar or tar. md5
no usb debugging is not related download mode is
dheeraj (dhlalit11) said:
can you tell which firmware comes in zipped file
either the firmware would be tar or tar. md5
no usb debugging is not related download mode is
Click to expand...
Click to collapse
take a look here, they are the original samsung firmwares and they come in zipped files - www.sammobile.com/firmware/
secondly i think i found the problem....in devices and printers- when i connect the phone it automatically shows "MSM7x27" unspecified device
u are missing drivers for it
i troubleshooted the problem and searched and installed many drivers for it but still no luck
when you will open the zip you will see tar files
ok lets be on the topic this means you have not installed tar files
download Kies latest version and install it
close it completely
open Odin and select files
boot mobile into download mode and connect it (do this after opening odin)
dheeraj (dhlalit11) said:
when you will open the zip you will see tar files
ok lets be on the topic this means you have not installed tar files
download Kies latest version and install it
close it completely
open Odin and select files
boot mobile into download mode and connect it (do this after opening odin)
Click to expand...
Click to collapse
already installed latest kies...closed it from task manager
tried doing that...yes there are tar files in the archive
i 'll try doing this on another laptop and let u know if it works
i finally found d problem....it is the msm7x27 missing on my laptop
its bcoz i recently upgraded to windows 8 pro 64 bit...it will work on any other pc running 7
the problem is resolved but still i want those drivers for windows 8 pro x64..if u found them please let me know
Can somebody give advice what to do?
Problem In following - Galaxy S (I9000) not rebooted in recovery mode after I flashing zImage (5 step in manual for Installing a custom recovery i.e. run 'heimdall flash --kernel zImage --no-reboot'). No combination does not work, but download mode still work. Than I tried flash recovery.img (Replicant's recovery.img), but it not helped. The phone not working now.
Another variant that I see is to install official firmware with using Odin, but in instruction no mention about kernel only PDA, PHONE and CSC. Can i to do it with using 'heimdall' instead 'Odin' and download mode will still work after those manipulations.
Please, help.
Did you fixed your phone?
Habibutsu said:
Can somebody give advice what to do?
Problem In following - Galaxy S (I9000) not rebooted in recovery mode after I flashing zImage (5 step in manual for Installing a custom recovery i.e. run 'heimdall flash --kernel zImage --no-reboot'). No combination does not work, but download mode still work. Than I tried flash recovery.img (Replicant's recovery.img), but it not helped. The phone not working now.
Another variant that I see is to install official firmware with using Odin, but in instruction no mention about kernel only PDA, PHONE and CSC. Can i to do it with using 'heimdall' instead 'Odin' and download mode will still work after those manipulations.
Please, help.
Click to expand...
Click to collapse
Hi.can you tell me please if you fixed your phone and how.i have the same issue and i can't find any working sollution.Thanks!
vatco said:
Hi.can you tell me please if you fixed your phone and how.i have the same issue and i can't find any working sollution.Thanks!
Click to expand...
Click to collapse
Download mode works? Good!
Flash any stock firmware via Odin. After that, you can flash whatever you wish. Check my thread, there is pretty much all you need:
http://forum.xda-developers.com/showthread.php?t=2444308
Follow unbricking guide step by step there.
I9000 Wont boot no service mode is it bricked?
hello i was trying to update the the stock recovery service boot options on my gt I9000 so i could upgrade to CyanogenMod 10.2 Android 4.3 Jelly Bean.
but i kept getting "E signature failed" in the service boot options, so i tryed to update the service mode screen and so it
would get rid of the "E signature error" with odin.
i opened an update rar file instead of a tar (should have noticed) and ran odin it failed and now i cant,
get my gt I9000 to boot into service mode or start up.
when i do try to start phone the up i just get an picture of a *Phone ! Pc*
http://dl-1.va.us.xda-developers.com/thumbs/2/3/6/7/6/6/4/2367664.jpg
i can only access download mode volume down+home+power key
i tryed to install and run "Heimdall version 1.3.1 from the guide in the thread (link below)
http://forum.xda-developers.com/showthread.php?t=1886393
but it wont install i just get MSCVR100.DLL Errors i reinstalled vcredist_x86.exe
and tryed to register the dll from cmd but it didn't work.
Im just looking through this thread on bricked the I9000 (link below)
http://forum.xda-developers.com/showthread.php?t=2434225
And trying the steps in that post.
i did backup using titanium and saved the entire contents of my phone to my pc can i restore my phone from that, via the Pc?
is there a way to replace the boot loaders on the phone with odin or another program?
it was Froyo 2.0 JPO
can anyone advise me what i can do please?
Update
Hi just a quick update
i reinstalled windows 7 on a old harddrive and managed to install heimdall & oneclick unbrick installed on that
in the cmd box it says
Error: Null
Set Temporary Folder:C:\Users\xai\AppData\Local\Temp\\xaiHeimdallOneClick\
Log:C:\Users\xai\AppData\Local\Temp\\xaiHeimdallOneClick\log.txt
Operating System: Windows
Found Heimdall Version: Heimdall v1.0.2b
Is the Null Error a problem?
the oneclick unbrick window says
Set Temporary Folder:C:\Users\xai\AppData\Local\Temp\\xaiHeimdallOneClick\
Log:C:\Users\xai\AppData\Local\Temp\\xaiHeimdallOneClick\log.txt
Operating System: Windows
Found Heimdall Version: Heimdall v1.0.2b
Ive installed the samsung drivers Pc installed compensate device and mass storage or something.
Im on an old pc with crap internet connection which keeps disconnecting every few mins, and it makes trying to view threads very difficult, am trying to find some threads i was looking in at the time of posting my op
is it safe to go ahead with the unbricking?
some advice at this point would be greatly appreciated
Thank's :
Futher Update
So i took the plunge an Clicked Unbrick, it then said it needed to install drivers, i followed the steps it then gave me and i clicked show all devices then my device was found, it installed the zadig drivers etc and then configured it all by its self and restarted my phone
All is good and well again
At this point ide like to thank the members whos contributions/guides on the forum helped me get things back on track and a big shout out to the heimdall/oneclick unbrick developers :good:
You all have done/do some great work
Thanks Again folks!!! :good:
Yours Sincerly Xai
Downgrade E3 To E2 Recovery
hello again
I'm trying to downgrade recovery mode from E3 To E2, ive searched and read a few of the threads but I'm still unsure what do to
I've got a...
GT I9000 (international sim free)
Firmware
2.2
Baseband
I9000xxjpp
Kernal Version
2.6.32.9
Build Number
Froyo.xxjpo
I was gonna open CF-Root-XX_XEU_JPO-v1.2-busybox-1.17.1 in odin and hit PDA.
theres a few conflicting guides on how and what to do and a few of the guide take me to links that want to install stuff on my pc etc which i dont trust.
some links say it will work as i decribed there others say you need a stock recovery file or an e2 recovery file for the Froyo.
im lost with how to proceed, can anyone help or link me to the files i need please?
Thank's Xai
E2 is totally outdated thing, why would you need that?
What is your point, what do you desire to install?
tetakpatalked from Nexus 7 flo
tetakpatak said:
E2 is totally outdated thing, why would you need that?
What is your point, what do you desire to install?
tetakpatalked from Nexus 7 flo
Click to expand...
Click to collapse
Hello Tetakpataki hope your good & thank's for your reply :good:
i was trying to apply the lag fix but it wouldn't install cos i was in recovery E3 and kept geting the "E Signature" failed error
Ive since flashed my phone with "speedmod-kernel-k13c-500hz.tar" and can now access E2 recovery but I'm now stuck in clockworkmod recovery v2.5.1.0 speedMod ULFK.
When i flashed it it auto check repartition i didn't notice till it was too late.
Every time i try to start the phone it goes to "clockworkmod recovery v2.5.1.0 speedMod ULFK" screen and i cant get out it, i can still get into download mode, but the phone wont boot up normaly
Ive flashed with bootloader "i9000 boot.tar.md5" but that didn't work i change the extension to "i9000 boot.tar" it flashed but i still goto recovery.
Ive read through a lot of threads and guides a lot of the links to files i apparently need are down
I'm at a total loss as what i can do now? i cant find the froyo stock rom or the bootloader either (international version) can someone help me out please?
My phone is
GT I9000 (international sim free)
Firmware
2.2
Baseband
I9000xxjpp
Kernal Version
2.6.32.9
Build Number
Froyo.xxjpo
I hope that makes thing easyer
Any help would be greatly appreciated thank's
Can you reach the download mode?
tetakpatalked from P5110
tetakpatak said:
Can you reach the download mode?
tetakpatalked from P5110
Click to expand...
Click to collapse
Hiya Tetakpatak :good:
yes i can get into download mode
im just having a look at Xsenman's "[Toolkit][A.I.O Rescue & Recovery] My Android Collection" thread (link below) and seeing if i can do anything suggested there
http://forum.xda-developers.com/showthread.php?p=29331775#post29331775
I'm gonna try "Make CWM Recovery .img's into .tar.md5 odin flash-able files 1 CLICK " and see if that works
also ive gotta try mount the sd cards internal & external so im having a look at that too
I'l let you know what happens any other advice would be great thanks
xai25 said:
I'm gonna try "Make CWM Recovery .img's into .tar.md5 odin flash-able files 1 CLICK " and see if that works
http://forum.xda-developers.com/showthread.php?t=2281287
Click to expand...
Click to collapse
I tryed that edited the bat renamed the file to recovery.img it didn't work and is a lot of hastle messing around editing any futher tbh
I went here
http://forum.xda-developers.com/showpost.php?p=14013450&postcount=1
tryed to download the "EZboot-Froyo-1.0.tar.md5 - Froyo" file but the links dead and i cant post in the thread.
cant i get file or a kernal and just flash it with odin then get back to normal no?
I finally got it fixed
Hello
I finally found a copy of the I9000XXJPO firmware (the other night) and flashed my phone with it.
the phone was getting stuck on the S slash screen.
But to fix that i flashed it with I9000 dbdata.rfs file (as i had a few E fail errors showing in recovery mode too) and it booted up fine after that.
I'm all up and running again
A Huge Thank's...
To All The Folk & developers, who spend a lot of time on the software, & contributed the guides and files to the forum
Great Work!! :good:
Your's Sincerely
Xai