Database Develop

[Solved]Kaiser won't charge past 37% and slide won't register

I think it's my fault because I used my kaiser in moist enviroment. (little rain) Afterwards after sliding I would hear sliding sound few times as if I would quickly slide in/slide out and my keyboard was quickly blinking.
I turned the phone off and let it dry. This fixed the blinking.
But first it went during use from 9x% to 2x% in few seconds, then last 20% drained pretty quickly too. I charged it and it went to 100% then did the quick drop again. I decided I would let it drain completely and then try charging it. Now it charges only until 37%. The charging icon is there in my WinMo, so USB probably works well.
Other than that sliding the phone in or out doesn't register at all in WinMo. I can live with that because I always set winmo to use only landscape orientation anyway. Too bad I don't have autounlock/screen on when sliding out anymore.
So, anyone has an idea how to make the phone behave as it should? I have screwdriver that I used with SPV C600 long time ago and I think it used the same screws, so I can get into my phone if neccessary and if fix is simple enough.

At least try a new battery if you can and see if that corrects the problem. Ironically, though, after one of my HTC's got submerged in water, the battery was the ONLY thing that worked everything else was shot.

Well, my friend has Kaiser as well and I was playing to test out each others battery, but I won't see him until Wednesday or so. Anyway, now it's stuck at 25% max, when it was 37% it lasted for about 2 hours. Even though I was reading e-book and listening to music, writing SMSes and it was on train so it probably often changed the towers. When I could charge it to max it obviously worked a lot longer. I usually charged it once every 2 days.
And I didn't think it was that bad weather. It was just mizzle, if dictionary tells me right, so only keyboard got wet afterwards. I didn't think it would affect insides. Anyway, I'll keep you informed on the experiments after Wednesday. If other battery will work without problem I'll just buy new one.

You are right, It happened to me with my first kaiser. I spilled milk on it and the only thing that worked after was the battery
chambo622 said:
At least try a new battery if you can and see if that corrects the problem. Ironically, though, after one of my HTC's got submerged in water, the battery was the ONLY thing that worked everything else was shot.
Click to expand...
Click to collapse
Kaiser dying very slowly
Areinu said:
Well, my friend has Kaiser as well and I was playing to test out each others battery, but I won't see him until Wednesday or so. Anyway, now it's stuck at 25% max, when it was 37% it lasted for about 2 hours. Even though I was reading e-book and listening to music, writing SMSes and it was on train so it probably often changed the towers. When I could charge it to max it obviously worked a lot longer. I usually charged it once every 2 days.
And I didn't think it was that bad weather. It was just mizzle, if dictionary tells me right, so only keyboard got wet afterwards. I didn't think it would affect insides. Anyway, I'll keep you informed on the experiments after Wednesday. If other battery will work without problem I'll just buy new one.
Click to expand...
Click to collapse

Ok, I tested it just now.
I charged my phone overnight. It was 25% when I woke, 8% when I got to my friend. I put my battery into his phone. It showed 90%.
My friend's battery was at 80%. Put into mine it showed 1%.
So it seems my phone can now see only last 20% or so of the battery. It's... not good. It means I have to fix the phone somehow. Now any ideas how? Later today I'll open it and try to find things out of ordinary and I'll make photos of them if I won't know what to do.

Areinu said:
Ok, I tested it just now.
I charged my phone overnight. It was 25% when I woke, 8% when I got to my friend. I put my battery into his phone. It showed 90%.
My friend's battery was at 80%. Put into mine it showed 1%.
So it seems my phone can now see only last 20% or so of the battery. It's... not good. It means I have to fix the phone somehow. Now any ideas how? Later today I'll open it and try to find things out of ordinary and I'll make photos of them if I won't know what to do.
Click to expand...
Click to collapse
Try to clean your battery terminals and see if that can help... http://forum.xda-developers.com/showthread.php?t=358136

I tried cleaning terminals before, didn't help. But I did thing described in 1st post of that thread. Today my battery maxed out at 12% no matter how long I would charge. The thing at first post made 45% detectable, which... is at least much better than 12%. Or 25%. Or 37%.
I've tried getting into the Kaiser yesterday but the screw under the speaker is stuck and halfway stripped and I had no luck trying to unscrew it. But it might not be necessary after all, if the method from that post helped in getting to 45% then maybe playing with the battery more will help. There's more methods in that thread, I'll try them out later.
Well, thanks a lot for the link. Now I'm getting hope back

Ok, here's the update.
Now the phone is running at about 32% juice max and no matter how I play with the battery it won't go above 32%.
When it's on 1% it lasts on it for quite a long time. Like 20-30 minutes. Then the phone turns off.
When I try to turn on the phone then it goes trough the screen with radio etc. then htc logo and turns off when windows would have started. No matter how many times I try to turn it on then it will do it like that. So, my theory is windows has some kind of energy saving feature that makes it turn off when it detects it's like 0.5%. I wonder if there was a way to make windows not turn off no matter what and if then maybe I could use 100% of the battery even if 68% of it would be on 1%. Of course it's just my idea and might not work. I don't know how kaiser checks the amount of power left and if my kaiser can get power from the whole battery even if it can't measure it well.
I wonder if android might work well?
I'm thinking about software solution because I can't go trough the broken screw below the speaker. I went to a shop to see if brand new screwdriver would manage to unscrew it, but even it slipped out(new screwdrivers are usually not curved at the edges so sometimes they work). I have no idea how to remove the screw.
Ah, when it turned off and it was turning off at windows I played with the battery and managed to turn it on with 3%. Well, even with additional 3% it was only like 3.5 hours of use at most from 32% I had at the begining.
So to sum it up:
do you think a software solution is possible?
do you have any ideas how to get rid of that screw without damaging the phone?

Areinu said:
do you think a software solution is possible?
Click to expand...
Click to collapse
Not if it's a hardware problem causing all the symptoms. Besides, you wouldn't be able to flash with less than 50% battery charge registered (don't know if microSD card flashing has this requirement as well but I wouldn't do that anyway).
do you have any ideas how to get rid of that screw without damaging the phone?
Click to expand...
Click to collapse
Your comment earlier about screwdriver edges being rounded off makes me wonder if you're using the right screwdriver to begin with. You do realise they're torx screws which are meant to be removed with special Torx screwdrivers don't you? If you have failed using the correct tool for the job then you could either try glueing the driver into the screw head and letting it set for a couple of days (being very careful not to get any gue anywhere else other than inside the screw head cavity). There are also devices called screw extractors or easy outs which require the head of the screw to be drilled down the middle first. I've used this technique with success in the past on a much bigger scale but I don't know if they go down small enough in size to suit these phone screws - you might want to talk with a jeweler to see what your options are. You'd also need to tape a plastic bag all around the screw to protect the rest of the phone from swarf if this method is possible/necessary. I think the phone is going to need opening up to get to the bottom of the problem as my first thought of cleaning the battery terminals has already been tried (assuming you did it thoroughly with some contact cleaner on the end of a cotton bud).

Flying Kiwi said:
Your comment earlier about screwdriver edges being rounded off makes me wonder if you're using the right screwdriver to begin with. You do realise they're torx screws which are meant to be removed with special Torx screwdrivers don't you? If you have failed using the correct tool for the job then you could either try glueing the driver into the screw head and letting it set for a couple of days (being very careful not to get any gue anywhere else other than inside the screw head cavity). There are also devices called screw extractors or easy outs which require the head of the screw to be drilled down the middle first. I've used this technique with success in the past on a much bigger scale but I don't know if they go down small enough in size to suit these phone screws - you might want to talk with a jeweler to see what your options are. You'd also need to tape a plastic bag all around the screw to protect the rest of the phone from swarf if this method is possible/necessary. I think the phone is going to need opening up to get to the bottom of the problem as my first thought of cleaning the battery terminals has already been tried (assuming you did it thoroughly with some contact cleaner on the end of a cotton bud).
Click to expand...
Click to collapse
I know about torx screwdrivers and I removed all Torx screws I had to go with, but under the speaker is single cross screw meant to be removed with Thompson screwdriver. If you look into confidential service manual(this forum links in few places to it ) it tells you you need few screwdrivers for the job. Well, I assumed those extractors that require drilling the screw are mostly for bigger ones, like in cars etc. This one is pretty small. But I'll try with the glue, it's probably big enough for glue to catch on without me gluing the screw to the phone which would be a disaster.
Flying Kiwi said:
Not if it's a hardware problem causing all the symptoms. Besides, you wouldn't be able to flash with less than 50% battery charge registered (don't know if microSD card flashing has this requirement as well but I wouldn't do that anyway).
Click to expand...
Click to collapse
It's why I suggested Android. With haret you don't have to flash to boot it. And I actually did it and am trying to run out of the juice since yesterday(Wifi always on etc). While WinMO says it's 3% android says it's 30%, and it goes down slowly like hell. But it's for sure hardware problem so I can't see why android would be able to use whole battery -.-; I am trying to get phone to lose all energy, then I'll see how high it will charge on android(for now it didn't charge past about 50% but as I said it goes down very slowly).
As for flashing, it usually doesn't take that long at 50% figure is just for safety. But before attempting to flash I would start with hard reset, probably would fix most of things flashing would.
Anyway, as for the screw, it's easter and I'm at family house, I didn't take my tools or anything so it will have wait till I'm back.

Areinu said:
I know about torx screwdrivers and I removed all Torx screws I had to go with, but under the speaker is single cross screw meant to be removed with Thompson screwdriver.
Click to expand...
Click to collapse
Sorry, mine has the Void sticker over it and I just assumed it was Torx like the rest.
It's why I suggested Android. With haret you don't have to flash to boot it.
Click to expand...
Click to collapse
You'd still need a reliable boot loader to load anything though and from the sounds of it, you don't have that.
But it's for sure hardware problem so I can't see why android would be able to use whole battery -.-;
Click to expand...
Click to collapse
I can't see why Android would offer a 'solution' given it's a hardware problem which presented itself after your phone was rained on.
As for flashing, it usually doesn't take that long at 50% figure is just for safety.
Click to expand...
Click to collapse
The flashing program wouldn't let me progress when I tried it once before and although the flashing process is much shorter than it would normally take to use 50% of your batteries power, the current consumed during the process is higher than during normal operation and it's important that the voltages don't dip below acceptable values when writing to the EEPROM/Flash Memory. Much better to start by fixing the hardware issue and then sorting out any possible corruption in the EEPROM afterwards once the battery is fully charged.

Flying Kiwi said:
Sorry, mine has the Void sticker over it and I just assumed it was Torx like the rest.
Click to expand...
Click to collapse
Oh, I had Void sticker there too. It's Torx as well. Once you remove big piece of plastic under that(to that piece is attached the speaker) you have access to new screw and it's not Torx anymore.
Flying Kiwi said:
You'd still need a reliable boot loader to load anything though and from the sounds of it, you don't have that.
I can't see why Android would offer a 'solution' given it's a hardware problem which presented itself after your phone was rained on.
Click to expand...
Click to collapse
Well, I don't really know how the Kaiser works but my theory is the method it determines how much energy is left differs a bit from how it drains energy. Desktop Windows on laptops have a feature when on ~3% energy left they hibernate "to prevent possible loss of data". When on Kaiser Windows ran out of juice I could turn the phone as many times as I wanted and it would turn once on windows, so I made a hipothesis that Kaiser CAN use rest of the battery but it just can't measure how much is left. Well, it's from all the tests I made as well.
Somewhere under keyboard the rain must have gotten on onto something that measures energy and shortcuted it, or I don't know, made electrons jump between 2 things that it shouldn't, that are used to measure power left? It's more of intuition than real reasoning, I know.
Anyway I let android run out of energy and once it got to 1% and showed "no battery" icon it ran for 6 hours more on WiFi, GPS and 3G turned on(I don't know if GPS worked, I was inside whole time). Windows mobile even without WiFi, GPS and 3G never even lasted 6h since the rain broke kaiser. Futhermore I had screen turned on most of the time(I wanted to get power down quickly, plus I wanted to see what's new on the android). The phone got hot from WiFi usage, so I guess it was draining some energy at least to make heat
Finally the phone turned off(android showed me turning off animation so it somehow predicted it's the end of the line). When trying to turn off kaiser afterwards it wouldn't budge so I think I really made it go out of the energy.
When I was interested in android when first version emerged I recall reading that android can show energy wrong and to fix it one was supposed to use up all energy, then to charge it to max. Well, as I managed to drain my battery fully I charged android and now it maxed out at 76%.
One more thing about android trough haret - you boot into Windows mobile that you have, then from microSD you run haret.exe that turns off winmo and boots linux. It mounts all files needed on microSD so there's no permanent changes, and no need to do anything to bootloader. I booted into Windows mobile to check percentage there and it sees 63%. Android still has 76%.
Flying Kiwi said:
The flashing program wouldn't let me progress when I tried it once before and although the flashing process is much shorter than it would normally take to use 50% of your batteries power, the current consumed during the process is higher than during normal operation and it's important that the voltages don't dip below acceptable values when writing to the EEPROM/Flash Memory. Much better to start by fixing the hardware issue and then sorting out any possible corruption in the EEPROM afterwards once the battery is fully charged.
Click to expand...
Click to collapse
Well, good thing is I don't have to flash the mobile to run android then. I didn't know about the currents but it makes a lot of sense when one thinks about it. I never had below 70% when changing roms just in case.
Flying Kiwi said:
Much better to start by fixing the hardware issue and then sorting out any possible corruption in the EEPROM afterwards once the battery is fully charged.
Click to expand...
Click to collapse
Yup, but I'm trying to make energy level at least acceptable while my actions shouldn't break anything. After all I'm not making any permanent changes on the Kaiser, just changing files on the microSD. I can't do anything to the hardware at least till Wednesday anyway.
Update: Ok, today I let it go out of all power again and afterwards the phone wouldn't charge no matter what. I know that sometimes one has to charge about 30 minutes before anything happens, but I kept it 2 hours, tried charger, then USB and even orange diode wouldn't light up. I thought that maybe battery broke.
I tried cleaning up connectors of the battery and graysh-silverish something appeared on them. Cleaning it up didn't help at all. I looked at USB port in my Kaiser under flashlight and from what I could see connectors weren't bent or anything. I tried (without using force) to push usb in to the limit. Didn't help.
Well, I wanted to check if maybe battery was at fault. I took out the battery and then put usb in, then tried pressing power and green diode lighted up. When afterward I put the battery in the orange diode normally lighted up and the battery charged, the windows mobile turned on and it showed about 1%.
Well, I guess using Kaiser at all might be a little dangerous for it untill insides are fixed, so I'll wait until I can unscrew that screw with glue. Anyway, this information might help someone understand what's happening, it's just simply bizzare for me.

Wednesday. I tried getting rid of the screw again. Failed. But I got inside. I realized(and called myself an idiot over and over again) that the screw only held that small board next to sound controller connected to phone, but I could still proceed to open it. Anyway, I got inside.
I looked around for things out of ordinary. There was some dust here and there, but nothing serious. Except for this:
What, wait, isn't that mold? It seems like it is... Well, I cleaned it all off. Furthermore I got rid of most of the dust, as I was inside already, checked connections here and there. General maintenance.
After turning on the phone:
- Slide in/Slide off works
- WinMo showed 77% and it's probably right. I charged it fully on android then used for enough time to get ~25% down.
After using it for a bit the phone froze. I restarted it and WinMo was showing 3%. I realized I didn't press the casing to the keyboard hard enough so there might have been some elements loose. Another restart and it shows 76% again. Well, let's see how far it will charge.
Update: It charged with normal speed to 100%, and both WinMo and android agreed on it. Case solved, I guess.

[Q] Drunk G1 turns itself off

Hi fellas, long time no see!
So, first of all, yes, I've used the search, but what I've found is threads about wet phones, mine I believe is already dry.
Situation: I'm in the club, glass of absolut and redbull in my hand, phone in my jeans pocket, extra glass of absolut w/redbull on the bar next to me. Fat drunk aproaches the bar and tips my glass with his elbow, all my drink spilled over my clothes. After a brief discussion I realized the guy was too drunk and was a worthless douche so I let it go. I reach for my phone and realize my pocket is soaked wet, when I take it out, phone is out, red light dim. So I turn it off, take it apart and forget about it til the next day. Next day, it began to turn on, but shut itslef off after a few secs, so I take it apart again (that is back cover, battery, SIM and sd, I dont have the screwdrivers to go further), cleaned what I could with alcohol, let it vent in front of a fan for a few hours, then in a bowl of rice for 2 days, no good.
So I got an extra phone and let it sit for more than a month. The other day I decided to give it another try and voila! it worked, had to be dry by now! used it for a day, left it charging, when I came back, it was off again, unresponsive. I have an extra battery, so I got one of those universal battery chargers, because I though the problem could be the phone not charging the battery. It was (even when the light turns on red and it says charging and all). So, first weird thing, light turns on red, screen says charging, but USB wont wont actually charge the battery if it is somewhere below.. 70% maybe, it does charge if it is lets say about 80% or above.
I used it like this for a week or so, and now, when I turn it on, after the bootscreen and the initial loop, the phone now powers itself off (with the text "turning off" -or whatever it says- and vibrating and all), even with the battery full. Tried with both batteries full, plugged in the usb (the light is green when full, and will even charge), erased battery stats (recovery works fine) but the damn thing wont load android properly!
Any ideas what might be causing this? it should be dry by now (its been like 2 months already and I let it vent and used the rice method), it doesnt smell funny (you know, like burnt, like when sth short circuits).

btw, also tried flashing the ROM again (i always have a couple in the sd just in case) and didn't work neither, does exactly the same.
i know it is a bit long to read but i wanted to give you the most insight i could. i know that it works! it did a couple days ago, but something got screwed with the startup and i dont know what it is!

i see that u tried flashing the ROM again, but just to be sure u did do a super wipe correct?
this is very strange though, and yeah it should be dried by now.

Thanks for the reply, and yes, I did! I'm sure that is not the problem :/

Problem with cool down mode.

well, my phone fell into the toilet yestedey, i pulled it out inmediatly, dried him, and turned it off. I waited 20 min and when i thought it was dry (yes, i now know that it was REALLY STUPID to do that) i turned it on, it booted normally and it works perfectly fine, but after 40-30 min, it enters in cool down mode. Thought it was because it still wasn't fully recovered so i turned it off and on again, but this time 5 min after it booted it entered in cool down mode.
After researching more, i put it in rice and left it all night, when i woke up i tried again, everything works fine, but it enters again in cool down mode in 40-30 min.
The phone doesn't overheat when it enters this mode, however i think it might be because some circuit enters in shock with residual water or is already damaged. My question is, how long should it be in rice ? and if the problem persist, i havel use alcohol to clean the components?

Try using a hair dryer on medium heat on the phone (heat the phone to approximately 40 centigrades by blowing warm air on it. This will generate evaporation and disipation of any water that is inside
the trick is to have the whole phone warmed up .. not just a little in one corner. The rice will absorb water, true, but not "large" quantities.

ro_explorer said:
Try using a hair dryer on medium heat on the phone (heat the phone to approximately 40 centigrades by blowing warm air on it. This will generate evaporation and disipation of any water that is inside
the trick is to have the whole phone warmed up .. not just a little in one corner. The rice will absorb water, true, but not "large" quantities.
Click to expand...
Click to collapse
I waited all day and turned it on again, now this is interesting, the phone seems to be ok, but it entered cool down mode again, instead of turning it off i leave it on and waited, the battery was draining so i decided to charge it, it seems it can't charge from the usb. I turned it and connected the charger, everything normal, but instead of the normal battery metter it shows up an empty battery with an ? on it.
I know the battery is fine because the phone actually responds, but i'm afraid the usb port is damaged.
I connected it to my computer, it appears it has a false contact, my pc recognizes it, and the phone for a seconds shows the normal battery metter, but it goes to the empty ? again.
What should i do?

You have water in the protection circuit of the battery itself. That protection circuit is measuring constantly the battery parameters and currently is reading something wrong.
Al you can do is wait longer ...
If I were you, I would open the phone and dry it from the inside (I opened mine to change the bezel after a drop and it is quite easy). All you need is some precision screw driver set and some patience.

ro_explorer said:
You have water in the protection circuit of the battery itself. That protection circuit is measuring constantly the battery parameters and currently is reading something wrong.
Al you can do is wait longer ...
If I were you, I would open the phone and dry it from the inside (I opened mine to change the bezel after a drop and it is quite easy). All you need is some precision screw driver set and some patience.
Click to expand...
Click to collapse
i decided to wait more, so i left it in rice these days. Now, i tried to turn it on, but it won't do nothing, i supposed it was the battery so i connected the charger and left it like 30 min. When i plug it to the charger, the green leed appears and it vibrates, but it doesn't do anything aside from that.
I might open the phone tomorrow and clean it with alcohol, then assemle it again and wait another hours before giving up, really thanks for helping and idiot like me.

BoredDude said:
i decided to wait more, so i left it in rice these days. Now, i tried to turn it on, but it won't do nothing, i supposed it was the battery so i connected the charger and left it like 30 min. When i plug it to the charger, the green leed appears and it vibrates, but it doesn't do anything aside from that.
I might open the phone tomorrow and clean it with alcohol, then assemle it again and wait another hours before giving up, really thanks for helping and idiot like me.
Click to expand...
Click to collapse
You could have removed CoolDown mode *.apk from the system -- but it is risky since as said before something is being read to the system wrong in order to enter in that mode, could be an over current sensor in the SoC that triggers that (maybe by the lowered resistance by the residual water in the system). Good luck!

IT LIVES ! IT WORKS AGAIN !.
I cleaned it and now it works ! Thank you very much !. The only damage was made to the power button, now it's a little bit harder to turn on but i can live with that.

Relax!!
Bro Hard Reset your phone and relax. Keep calm you are not in trouble so please take it easy firstly hard reset your phone so it will be nice to your phone and you will not go in rice again. I hope you understand and give me a thanks on my post thank you very much hope you like it

[Q] Battery Status Unknown.

Ok guys, Last night my HTC One got water damage, I was using it for 5 minutes and it was keep bootlooping, I switched it off for 1 night and put it in Sun light for an hour, Now it is working fine except battery, its showing Exclamation mark on Battery and stuck on 13%. What should i do ? please help me.
I switched it off and let it charge for 10 minutes, now its showing 15%.

That was really silly. You should turn it off straight away and put It in rice for a few days. Quite frankly I'm suprised it still works at all. Water damage is never good. Probably needs to go in for repair

nateboi81 said:
That was really silly. You should turn it off straight away and put It in rice for a few days. Quite frankly I'm suprised it still works at all. Water damage is never good. Probably needs to go in for repair
Click to expand...
Click to collapse
thank you for your reply, but it shows just unknown battery status and my phone is not in warranty.

avesh6994 said:
thank you for your reply, but it shows just unknown battery status and my phone is not in warranty.
Click to expand...
Click to collapse
The phone is still wet inside
turn it off - put in a ziplock bag of rice for 3-4 days, letting it set in the sun may speed it up but not by alot

clsA said:
The phone is still wet inside
turn it off - put in a ziplock bag of rice for 3-4 days, letting it set in the sun may speed it up but not by alot
Click to expand...
Click to collapse
ok thank you so much.

i disconnect my charging and turned it off but however its still showing charging

[Q] Can re-soaking fix water damage?

I know it seems like a stupid question but I've got nothing to loose at the moment so I'll explain my situation.
About 3 months ago I took my Xperia Z1 for a swim in the pool to see how the camera performed underwater. The screen started to go black when I took it out and then it completely shut off. I took it inside and turned it on again. It lasted a minute before shutting off so I plugged it in to the charger and got the boot logo before shutting off again with nothing: Screen was off, no led, no vibrations, nothing.
I opened the flaps and they were still white and still are today and there was no moisture or anything. I tried plugging the phone in a few days ago to see if it still works and the led turned on and it just stays like that with no action. Left it for a few hours but still nothing.
I don't really need this phone anymore because I have a Z5 now but a second handset is always nice to have. The pool water would have had a very small amount of salt in it and I think that might be causing issues. Either that or there is still water in there (unlikely) or parts have rusted or even the phone might have got shocked when I plugged it in to charge. What I was thinking was opening the ports and soaking it in water for a minute or less and then taking it out and putting it in a bag of dry rice to drain the water out of it. I'm not sure if it will work but I haven't got anything to loose so I was wondering if it is even worth giving a shot or even some tips would be nice.

tommylittle02 said:
I know it seems like a stupid question but I've got nothing to loose at the moment so I'll explain my situation.
About 3 months ago I took my Xperia Z1 for a swim in the pool to see how the camera performed underwater. The screen started to go black when I took it out and then it completely shut off. I took it inside and turned it on again. It lasted a minute before shutting off so I plugged it in to the charger and got the boot logo before shutting off again with nothing: Screen was off, no led, no vibrations, nothing.
I opened the flaps and they were still white and still are today and there was no moisture or anything. I tried plugging the phone in a few days ago to see if it still works and the led turned on and it just stays like that with no action. Left it for a few hours but still nothing.
I don't really need this phone anymore because I have a Z5 now but a second handset is always nice to have. The pool water would have had a very small amount of salt in it and I think that might be causing issues. Either that or there is still water in there (unlikely) or parts have rusted or even the phone might have got shocked when I plugged it in to charge. What I was thinking was opening the ports and soaking it in water for a minute or less and then taking it out and putting it in a bag of dry rice to drain the water out of it. I'm not sure if it will work but I haven't got anything to loose so I was wondering if it is even worth giving a shot or even some tips would be nice.
Click to expand...
Click to collapse
Resoaking your phone will help as much as trying to jump from a cruise ship in the middle of the ocean for the second time and you can't swim...

optimumpro said:
Resoaking your phone will help as much as trying to jump from a cruise ship in the middle of the ocean for the second time and you can't swim...
Click to expand...
Click to collapse
Haha yeah that's what I thought

tommylittle02 said:
Haha yeah that's what I thought
Click to expand...
Click to collapse
To clarify, the Xperia Z1 relies on closed ports to ensure waterproofing. So soaking it a second time would destroy it further.

there is a easy way you can try.
buy some electrical contact cleaner from a computer shop or maplins etc, spray that all over the circuitry and contacts and scrub it off with a paint brush, there is a good chance it will work again as it will remove any corrosion casued by water, ive repaired hundreds of water damaged phones this way and it doesnt need any special things.....