Related
Simple question. I messed up my phone and want to return to the original.
I am a Canadian BELL i9000m - JL2 is what I need.
I know more-or-less how to flash etc. my question is this:
I am on the super optimized kernal, and seeARMS 2.2 JL2 rom.
all I have to do is get the original stock firmware released by bell/samsung for i9000m (JL2) and put it into Odin (and then once in download mode) it should work ?
my question is what boxes do I tick
like how do I get my stock kernal back - I need to get the modem, kernla, rom, etc. back to stock - which boxes in odin do I check ?
Disable any lag fixes you may have on the fone and download JL2 from samfirmware, unzip the file then pop it in the pda field in Odin, don't tick any boxes. Put your fone in to download mode - connect to pc then click start. This will flash JL2 on to your fone.
sean2476 said:
Disable any lag fixes you may have on the fone and download JL2 from samfirmware, unzip the file then pop it in the pda field in Odin, don't tick any boxes. Put your fone in to download mode - connect to pc then click start. This will flash JL2 on to your fone.
Click to expand...
Click to collapse
thanks alot man. and this will remove the other kernal too i suppose ?
anything else I have to disable? I put a few other fixes on there I think.
The flash will restore the fone back to stock and remove all your previous data including kernal. Do a factory data reset after the flash
sean2476 said:
The flash will restore the fone back to stock and remove all your previous data including kernal. Do a factory data reset after the flash
Click to expand...
Click to collapse
Thanks man -
I assume from there i can try and do it again and hopefully I won't mess up ?
I wonder if you can help me out so I don't break my phone again. Here are the instructions:
To install this ROM:
1. Download and extract the file you downloaded above to the root of your internal SD card (both the "seearms" folder and the .ZIP ROM file).
If you would like to customize your install, continue doing step 2. If you would like a stock install with all the applications + SpeedMod kernel + JL2 modem + Generation X theme, skip to step 3 (however I'd recommend customizing your install. )
2a. Browse to the "seearms/kernel" folder on your SD card and delete whichever kernel you do not want to install.
2b. Do the same with the "seearms/modem" folder: delete whichever one you don't want to install (I'd recommend installing the JL2 modem unless you've specifically had problems with it).
2c. Do the same with the "seearms/applications" folder: delete whichever applications you do not use. You're allowed to delete all of them to create a slim install, or delete none to create a stock install.
2d. Browse to the "seearms/extra" folder on your SD card, and delete whichever extras you do not wish to install (You're able to choose the Generation X theme, blue Android Market, custom boot animations, etc). Most importantly, if you would like the ROM to wipe your data, leave "wipe" untouched. If you don't want it to format your data, delete "wipe".
2e. So, before going further, you should have the following folder structure on your SD card:
"seeARMS.UGJL2.v0.4.zip" - anywhere on your SD card, doesn't matter
"seearms/extra" - customized to your liking
"seearms/applications" - customized to your liking
And a single file in both of these folders, depending on the kernel and modem you wish to install:
"seearms/kernel"
"seearms/modem"
3. Boot into recovery, and select "Install zip from sdcard".
4. Select "Choose zip from sdcard", and scroll to the ROM.
5. Select OK, and wait for the file to flash.
6. Reboot. This reboot will take a while (upwards of 2-5 minutes), so be patient and don't shut off your phone!
Congratulations, you've successfully flashed!
--------------------------------
Basically I get stuck at option 2 to 3
I didn't opt for the "custom" install (2a-2e) so I just went with the normal install and skipped to step 3
some guy said that I needed to delete certain things from the folder to customize the install -- but I didn't see that in the instructions - I just basically downloaded the seeARMS rom.zip and put it in my SD card and installed it from CWM that way -- was this wrong ?
Bin that ****e mate
1. Remove any lag fixes
2. Download the file
3. Unzip it
4. Open Odin
5. Put the unzipped file (now a .tar file) in the PDA box of Odin
6. Put fone in to download mode
7. connect to pc and odin will pick the fone up and the coms box will turn yellow
8. click start and let it do its thing.
The reboot will take about 10 minutes after the flash.
Add:
0) Charge your battery @ 100%.
0') restart your computer, dont start anything in background, open odin only, check and kill all Kies process.
0'') Make some coffee, chill a bit and you good to go.
ttf said:
Add:
0) Charge your battery @ 100%.
0') restart your computer, dont start anything in background, open odin only, check and kill all Kies process.
0'') Make some coffee, chill a bit and you good to go.
Click to expand...
Click to collapse
thanks guys - I understand fully how to get my phone back to stock 2.2 now.
But I still want to re-flash seeARMS rom again -- the question is how to do it without messing up my phone again. As stated, I posted the instructions above, I get stuck at step 2 - not sure how to go about it to be honest
You need to root your fone then flash the custom rom via Clockwork recovery. The instructions above look ****e mate. With the custom rom you put the .zip file on the root of the internal sd card then reboot in recovery then toggle down to install zip file then choose zip file. You must have clockwork recoverymod working first which you can download from the market
sean2476 said:
You need to root your fone then flash the custom rom via Clockwork recovery. The instructions above look ****e mate. With the custom rom you put the .zip file on the root of the internal sd card then reboot in recovery then toggle down to install zip file then choose zip file. You must have clockwork recoverymod working first which you can download from the market
Click to expand...
Click to collapse
"With the custom rom you put the .zip file on the root of the internal sd card then reboot in recovery then toggle down to install zip file then choose zip file. You must have clockwork recoverymod working first which you can download from the market"
I did this - and the ROM didn't come out and work as good (the home button didn't work) the reason I was told was because I didn't "customize" the installation --- apparently I didn't read the instructions correctly -- which is why I posted the instructions and was hoping someone could explain it to me where I was wrong
http://forum.xda-developers.com/showthread.php?t=906977
here they are :
NOTE: If you have a Bell i9000M, do the following to (hopefully) prevent your internal SD card from dying:
1. Upgrade to JL2 using either Kies (recommended) or Odin (make sure to check Bootloader Update).
2. After the upgrade, download and flash Super Optimized Kernel, which will give you access to ClockworkMod Recovery. Instructions to do so can be found in the FAQs (Q1).
(More information regarding the internal SD card dying can be found in Q2 in the FAQ)
To install this ROM:
1. Download and extract the file you downloaded above to the root of your internal SD card (both the "seearms" folder and the .ZIP ROM file).
If you would like to customize your install, continue doing step 2. If you would like a stock install with all the applications + SpeedMod kernel + JL2 modem + Generation X theme, skip to step 3 (however I'd recommend customizing your install. )
2a. Browse to the "seearms/kernel" folder on your SD card and delete whichever kernel you do not want to install.
2b. Do the same with the "seearms/modem" folder: delete whichever one you don't want to install (I'd recommend installing the JL2 modem unless you've specifically had problems with it).
2c. Do the same with the "seearms/applications" folder: delete whichever applications you do not use. You're allowed to delete all of them to create a slim install, or delete none to create a stock install.
2d. Browse to the "seearms/extra" folder on your SD card, and delete whichever extras you do not wish to install (You're able to choose the Generation X theme, blue Android Market, custom boot animations, etc). Most importantly, if you would like the ROM to wipe your data, leave "wipe" untouched. If you don't want it to format your data, delete "wipe".
2e. So, before going further, you should have the following folder structure on your SD card:
"seeARMS.UGJL2.v0.4.zip" - anywhere on your SD card, doesn't matter
"seearms/extra" - customized to your liking
"seearms/applications" - customized to your liking
And a single file in both of these folders, depending on the kernel and modem you wish to install:
"seearms/kernel"
"seearms/modem"
3. Boot into recovery, and select "Install zip from sdcard".
===============================================
It's in between step 1 and 3 that I get confused - the customization - it says if you want a stock installation just do you what you told me, select from CWM and install from zip card - but I did that and it didn't work
seeARMS said something about a "wipe" version and that I should do that and I should be fine - i don't understand this "wipe" version I wasn't prompted with a choice for this when I did it
I think your best to ask for help in the actual topic/ thread where you downloaded the rom from in the first place.
I have a similar issue, as I stated on the thread I've opened a few minutes ago...
Funkadelick said:
Simple question. I messed up my phone and want to return to the original.
I am a Canadian BELL i9000m - JL2 is what I need.
I know more-or-less how to flash etc. my question is this:
I am on the super optimized kernal, and seeARMS 2.2 JL2 rom.
all I have to do is get the original stock firmware released by bell/samsung for i9000m (JL2) and put it into Odin (and then once in download mode) it should work ?
my question is what boxes do I tick
like how do I get my stock kernal back - I need to get the modem, kernla, rom, etc. back to stock - which boxes in odin do I check ?
Click to expand...
Click to collapse
The best way to revive your I9000m is to first flash JPC (a three file ROM) with 512 PIT and repartition ticked. The phone will still be in a boot loop. Then flash the JL2 PDA without repartition or PIT. The best way to go back to stock! Has always worked for me. I9000m's are not the same as other I9000's and do not flash repartition and the PDA in the same flash! Good luck!
droilfade said:
The best way to revive your I9000m is to first flash JPC (a three file ROM) with 512 PIT and repartition ticked. The phone will still be in a boot loop. Then flash the JL2 PDA without repartition or PIT. The best way to go back to stock! Has always worked for me. I9000m's are not the same as other I9000's and do not flash repartition and the PDA in the same flash! Good luck!
Click to expand...
Click to collapse
I have an I9000m from bell, and i just used the JL2 from samfirmware with only the PDA file and it worked for me perfectly. I just had to do a factory reset after flashing and everything was back to what bell gave me.
I initially looked for a complete update guide on here and eventually found all the information I needed, but it was in multiple places and sometimes hard to find. After getting everything installed on my N1 I thought I would write a guide for other noobs like me that want to try out ICS or JB but would like a step-by-step guide. I hope that it is helpful. SpazeDog ROMs (both ICS and JB) are working wonderfully on my N1 - its a very nice update from CM7 with only minor issues so far.
Note: this was initially written specifically for SpazeDog roms, but as they have not been updated in a while I have provided links to other popular roms as well. If you would like to try a different ICS or JB rom this guide should work, just substitute with the appropriate rom and depending on the one you choose, you may also need to install Google apps.
If you looking at this guide and don't know the basics yet, check out the Newbie Friendly thread first.
Links to popular roms that will work using this guide:
Evervolv JB 4.2
Evervolv JB 4.1
CM 10, JB 4.1.2 by vijendrahs
CM 10, JB 4.2.1 by vijendrahs
Spazedog ICS/JB
Disclaimer: This guide involves making changes to your phone that potentially could brick your phone leaving it unusable. I am not liable for any changes you make or problems you may have with your phone. You should at least be familiar with entering commands using command prompt. This procedure will erase ALL the data on your phone. Make sure you have a backup of everything. A nandroid backup is highly recommended. Proceed at your own risk.
Before we get started make sure you have the following: a rooted Nexus One, a USB cable to attach your phone to a computer, and the Android SDK. If you are just now installing the Android SDK, open the SDK manager and make sure to install the "Tools" and in "Extras" the "Google USB Driver" are checked off and download them. Alternatively, you just download ADB and Fastboot (search this forum or google). If you have a Mac see this thread to get started with ADB and Fastboot.
If you Nexus One is NOT already rooted, then follow this guide from Cyanogenmod to root your phone. If you plan to use the adb commands below (they are optional) make sure you have usb debugging enabled: go to "Settings" → "Applications" → "Development" → enable "USB debugging."
Step 1 - Download everything you will need:
4EXTRecovery Updater - the first link will download the .apk to your computer or phone.
BlackRose - go down to bottom of the first post to "Attached Files" and download the latest BlackRose zip file. If you don't want to do it yourself, check out this thread to flash a pre-made partition scheme. Often the developers (Evervolv) will also have a partition schemes that you can flash via Fastboot from your PC as well.
Your rom of choice - go to the downloads section and choose which rom you would like to try. Download the zip installation file.
Since you will be decreasing the size of your partition that apps can be stored on consider something like Mounts2SD or AD2SDX to move apps to your SD card.
Step 2 - Install and use 4EXTRecovery Updater on your phone:
The easiest thing to do is go to the 4ext link above, download and install it, directly from your nexus one. You can also install it by copying the APK file to your SD card, then using a file manager to find it and install it or you can use command prompt by opening command prompt, cd to the location of the Android SDK tools, and then type in the following command (replacing "path" with the path to where the APK is located on your computer):
Code:
adb install /path/4EXTRecoveryUpdater.apk
After you have installed 4ext open the 4EXT Recovery Updater. Tap "Settings" → "Allow" superuser request → "Yes" to connect to 4ext to get new data. Now select "Online install/upgrade" → "Yes" assuming it detects your nexus one correctly → select and install the latest 4ext recovery (at the top of the list).
After 4ext has installed, it will have placed a recovery image on your SD card - find it (its called recover.img) and it should be located in SD/Download/4EXT_Recovery_Touch/ folder. Copy this to your computer in case something goes wrong later and you need to re-flash the recovery image!
After installation of the 4ext recovery turn off your phone and boot into recovery by turning off your phone, turning it on again while holding the trackball down. This will boot into the bootloader, then press the power button once, use Volume Down to select "recovery" and press the trackball to select. Alternatively you can use the command prompt:
Code:
adb reboot recovery
Your phone should now boot into the 4ext recovery menu. Before moving on make sure you have any important stuff backed up because you are about to erase your entire SD card! Select "tools" →“partition sd card” → “remove all partitions and start from scratch.” Then for the 1st partition select “1024″ for a 1GB partition (this will be where ICS will be able to put your applications & data). Select "skip" for the 2nd partition and for the swap partition. Finally select the system “ext4″.
Step 3 - Copy the Evervolv, SpazeDog, or whatever zip installation file you have chosen to your phone's SD card
Download the ICS or JB zip file above and copy it to the root of your newly formatted SD card.
Step 4 - Installing and using BlackRose to resize the system partition:
Download the BlackRose application and install it on your computer. (Alternatively people have made flash-able partition schemes that you can just flash from your PC - usually links and instructions are provided in the installation rom's thread, Evervolv's here. If you do have access to a computer you can check out this thread).
Make sure your nexus one is attached via USB to your computer.
Open the BlackRose application - it will install and reboot your phone. Then follow along as shown in this video to resize your partitions for a JB ROM.
If you plan to install the ICS rom then use the video above as a guide but use the numbers (sizes) for the different partitions as indicated below.
After BlackRose has installed you will need to restart the application. After it has started up and recognized your device select "apply stock/custom blackrose" by typing in 1 and enter.
Then select "custom blackrose" by typing in 2.
Then type "resize" when prompted.
Now you will need to change the sizes of the system partition to 220 for ICS or 260 for JB.
Change the cache size to 8.
Finally name the new system partition, either "ICS" or "JB" depending on what you plan to install.
Note: some people have reported having problems getting into recovery at this point (if not move on to step 5). If that happens, luckily for you, 4ext put a recovery image in the downloads folder of your SD card and if you did what I said in step 2 you saved it. Try reflashing that recovery image using fastboot (remember the one that was in SD/Download/4EXT_Recovery_Touch/ and was named "recovery.img"). Put your phone into the bootloader by turning off your phone, turning it on again while holding the trackball down. To reflash the recovery open command prompt and cd to the location of the Android SDK tools. Then type in the following command (replacing "path" with the path to where the recovery image is located on your computer):
Code:
fastboot flash recovery /path/recovery.img
If that does not solve your problems (inability to get into recovery) then I would recommend going back to the cyanogenmod wiki and installing Amon_Ra's recovery. Then you can use it to flash your installation zip.
Step 5 - Install JB or ICS:
Now turn your phone off and boot into recovery as you did in step 2.
4ext will load. Select "wipe/format" → "format all partitions (except sdcard)" and then also "wipe data/factory reset."
Now go back and select "install from sdcard" → "choose zip from sdcard" → and then select the ICS or JB zip you copied to the SD card in step 3.
Now either the ICS/JB installer will load or it will just install in one step. Just follow the prompts to install and enjoy.
Depending on the ROM you chose you may need to install Google apps (see the specific ROM thread for details) and will also likely want to flash an apps-to-SD script as mentioned above so you do not run out of space.
This method worked perfectly for me, hopefully it will work well for you as well. Enjoy.
Great work, your guide is amazing!!! I followeed it and ended with an infinite bootanimation , I'm trying to discover what I did wrong :fingers-crossed:, but the guide was superb!
diegolm said:
Great work, your guide is amazing!!! I followeed it and ended with an infinite bootanimation , I'm trying to discover what I did wrong :fingers-crossed:, but the guide was superb!
Click to expand...
Click to collapse
I am sorry to hear that. Can you boot into recovery or is that broken as well? If you can boot into ext recovery try selecting "wipe/restore" → "wipe data/factory reset" and then try to install BCM again. I probably should have added that above, I will do that now.
If your recovery is broken but you can get into the bootloader (holding down trackball while starting up), you should be ok. You will probably need to flash Amon_Ra's Recovery using Hboot as was described in the guide from cyanogenmod link above. If there is a way to directly hboot flash 4ext recovery I don't know how to do it. Then you can try installing BCM again from the Amon_Ra's recovery and re-install 4ext after you get everything working.
I tried the Texasice ROM and it worked, but I didn't like it! Later I tried again BCM and It worked! I dont know, maybe I did something wrong... Anyway thanks again for the guide!!
Does work the same if using fastboot method? Thx
Sent from my Nexus One using Tapatalk 2
intel415 said:
Does work the same if using fastboot method? Thx
Sent from my Nexus One using Tapatalk 2
Click to expand...
Click to collapse
I am not sure which part you are referring to, but, yes, a few of the above instructions could be replaced with fastboot commands.
The adb commands, instead using adb I can use fastboot commands right. That's what I used to root my n1 kinda familiar with fastboot. Thx
Sent from my Nexus One using Tapatalk 2
intel415 said:
The adb commands, instead using adb I can use fastboot commands right. That's what I used to root my n1 kinda familiar with fastboot. Thx
Sent from my Nexus One using Tapatalk 2
Click to expand...
Click to collapse
I used the adb commands above because you can use adb to reboot directly into recovery (fastboot you can only reboot normally or into the bootloader) and you can also use adb to directly install apk files - fastboot cannot do those two things - it is more for flashing images (recovery, roms, etc). In order for adb to work make sure you have usb debugging enabled: go to "Settings" → "Applications" → "Development" → enable "USB debugging."
Note that adb commands are not required - you can reboot into recovery and install the 4ext manually.
It won't let me post a link right now, but just google "adb commands" to find a list of all the commands you can use.
Hope that helps.
Thx. All I need it was to install black rose and partition it. Put zip on SD card wipe and flash. Installation was easier than I thought it would be lol
Also on ur guide you forgot to put 200 for the data part. You only had 220 and 16
Thx again got ics installed on my n1 smoother than cm 7.2
Sent from my Nexus One using Tapatalk 2
intel415 said:
Thx. All I need it was to install black rose and partition it. Put zip on SD card wipe and flash. Installation was easier than I thought it would be lol
Also on ur guide you forgot to put 200 for the data part. You only had 220 and 16
Thx again got ics installed on my n1 smoother than cm 7.2
Sent from my Nexus One using Tapatalk 2
Click to expand...
Click to collapse
Yeah, its not bad - glad you got it working! ICS has been smoother than cm 7.2 for me as well.
Blackrose didn't ask me about userdata - it just assumed that automatically after putting in 220 system and 16 cache... I'll make note of that in the guide so its clearer. Thanks.
Got the issue with not being able to get into recovery after step 4, but I don't have the recovery image to flash. Once the SD card was formatted in step 2 I don't have a download folder. I attached what is in my SD card right now. Help please.
Look for "recovery.img"
bobbyphoenix said:
Got the issue with not being able to get into recovery after step 4, but I don't have the recovery image to flash. Once the SD card was formatted in step 2 I don't have a download folder. I attached what is in my SD card right now. Help please.
Click to expand...
Click to collapse
Try to find if there is a "recovery.img" anywhere on your SD card, perhaps in the 4ext folder?
If you can't find it, do not worry, you can just go to the first page of this thread, click on the link labeled "follow this guide from Cyanogenmod" and then go to the section on how to download and install Amon_Ra's Recovery. Once you get Amon_Ra's recovery flashed you will be able to install any ROM of your choice.
You can reinstall the 4ext recovery later if you want.
c2med said:
Try to find if there is a "recovery.img" anywhere on your SD card, perhaps in the 4ext folder?
If you can't find it, do not worry, you can just go to the first page of this thread, click on the link labeled "follow this guide from Cyanogenmod" and then go to the section on how to download and install Amon_Ra's Recovery. Once you get Amon_Ra's recovery flashed you will be able to install any ROM of your choice.
You can reinstall the 4ext recovery later if you want.
Click to expand...
Click to collapse
OK I'm stuck on what the path name is suppose to be. I tried it every way I can think of. Can you take a look at my screen shot, and tell me where I'm going wrong? The recovery image is on my desktop, so I'm not sure what exactly I should be replacing "path" with. I tried it from the link, and how you have it in your note. You don't have the "/to/" after path as in the CM link.
Well I tried a couple more times, and I can get it to seemingly do it, but it just hangs on this: (see screen shot) I get no error, and if I try to enter recovery on the phone I still get the reboot to the android and triangle with the ! in it.
place the recovery under the folder which contains fastboot.exe and rename it to recovery.img
now use the command
fastboot flash recovery recovery.img from platform-tools directory
Sent from my Nexus One using Tapatalk
And right-click this folder while pressing the SHIFT key on your keyboard. Then choose "Open command window here".
n1newbie said:
place the recovery under the folder which contains fastboot.exe and rename it to recovery.img
now use the command
fastboot flash recovery recovery.img from platform-tools directory
Sent from my Nexus One using Tapatalk
Click to expand...
Click to collapse
tommert38 said:
And right-click this folder while pressing the SHIFT key on your keyboard. Then choose "Open command window here".
Click to expand...
Click to collapse
WOW Thank you both. I spent literally hours yesterday trying to get it to work. Tried your suggestions, and in five minutes it was up and running!
---------- Post added at 12:31 PM ---------- Previous post was at 11:33 AM ----------
I may have spoke too soon. I followed the instructions to the end. Installed the ROM, and rebooted, but now after the X I get the Spazdog splash screen with the big Z in the middle and green dots moving, but it stays there forever. I waited 20 minutes one time. Tried reflashing, but I get the same thing.
---------- Post added at 01:17 PM ---------- Previous post was at 12:31 PM ----------
Just giving an update on progress (in case someone else is in my boat too) Flashed back to stock GB. Reinstalled recovery, and reflashed Spaz. Got past the X, and the splash screen, but now it's stuck on the Android logo that looks like the night rider beam that goes across the word. Been there now for about 10 minutes.
You do have Blackrose, right?
Yep. Installed everything according to OP. I think it may be the partition sizes as I think flashing back to GB messed with them. It says 220 and 10, but after checking some threads, it looks like there is one missing (userdata). I tried flashing a custom GB from here http://forum.xda-developers.com/showthread.php?t=1214543&page=98 and I was able to install everything. Got it up and running, so I'm going to start over for ICS, or do you think I can flash one of these for ICS http://forum.xda-developers.com/showthread.php?t=1637166 , and then just flash the ROM after?
220/10 means that you have 220MB for system and 10MB for cache, everything that's left will be userdata, so it doesn't ask (total is ~436MB, so userdata will be ~206MB in that case).
In HBOOT you can check how large your partitions are, or you could use the FreeSpace app for example. Always make sure your system partition is large enough before flashing a ROM.
Hello,
I tried installing a custom ROM on my 7310 and it had issues. I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop. I think I need to repartition, but when I click the repartition checkbox in ODIN I get an error.
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Thanks.
A few questions:
spazlon said:
I tried installing a custom ROM on my 7310 and it had issues.
Click to expand...
Click to collapse
What did you try to flash and how did you try doing it (CWM, ODIN, ...)?
What 'issues'?
I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop.
Click to expand...
Click to collapse
How far into the boot sequence does it get?
Are you able to get into recovery?
If so, what recovery do you have (Stock vs CWM)?
Have you tried seeing what is causing the boot-loop using adb?
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Click to expand...
Click to collapse
This is an action of last resort. Exhaust all other avenues first.
boscorama said:
What did you try to flash and how did you try doing it (CWM, ODIN, ...)?
What 'issues'?
Click to expand...
Click to collapse
I used CWM to flash AOSP 4.1.2. It seemed to work fine for a day or two, but then it needed charging (as normal). I let it charge over night and in the morning it had less battery. I figured the charger or cable were flaky so I tried another set on another outlet and same thing. Then it finally ran out of battery. I let it charge again over night and when I tried to turn it on it was really slow. The boot animation was only 1 frame every couple seconds. It would eventually boot all the way up, but it was still REALLY slow. So I went into CWM and reflashed the same ROM. Then I got a boot loop of the boot animation. I couldn't get into CWM any more, so then I went into download mode and flashed the official firmware and flashed it with ODIN.
boscorama said:
How far into the boot sequence does it get?
Click to expand...
Click to collapse
Now when I turn it on it just says, "Firmware upgrade encountered an issue. Please select recovery mode in Kies & try again."
I can flash again with ODIN and it will get to the Samsung boot animation and just pulse SAMSUNG.
boscorama said:
Are you able to get into recovery?
If so, what recovery do you have (Stock vs CWM)?
Click to expand...
Click to collapse
If I hold power and volume down I can get into download mode or Samsung recovery, not CWM, and power with volume up doesn't do anything.
boscorama said:
Have you tried seeing what is causing the boot-loop using adb?
Click to expand...
Click to collapse
I don't know anything about adb and I'm not sure what I would be looking for. Is there a tutorial I can follow somewhere?
Thanks for any help!
This worked for me with similar problem
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Thanks! I'll give this a try when I get home. I'll let you know how it works out.
Don't ever try to 'repartion unless you really know what you're doing. You're soft bricked. Repartion and you'll hard brick.
I'd go back and get hc from sammobile and flash that with Odin. Ics has had some problems.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
jd1639 said:
Don't ever try to 'repartion unless you really know what you're doing. You're soft bricked. Repartion and you'll hard brick.
I'd go back and get hc from sammobile and flash that with Odin. Ics has had some problems.
Sent from my SAMSUNG-SGH-I727 using xda app-developers app
Click to expand...
Click to collapse
Agreed - my procedure avoids manual repartitioning - I tried lots of other procedures but none worked. I think my data partition had become corrupt because I kept getting error messages. My first try was to recover with my cwm recovery file I made originally but I kept getting back to the boot loop .
spazlon said:
Hello,
I tried installing a custom ROM on my 7310 and it had issues. I have tried installing the original ICS from the sammyfirmware site using ODIN. Now I have a boot loop. I think I need to repartition, but when I click the repartition checkbox in ODIN I get an error.
Do I need to repartition? If so, how do I do it? If not, how do I fix this error?
Thanks.
Click to expand...
Click to collapse
I always got something like that ...
After bootloop just go to recrovery mode then factory riset ... its 100% WORK
Sent from my GT-P7300 using xda premium
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
spazlon said:
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
Click to expand...
Click to collapse
Sorry - being a newbie myself I'm at a loss. It worked a charm for me.
spazlon said:
I followed the steps outlined by mobjunky and was able to get an official Honeycomb ROM installed, boot the official and copy my custom ROM and CWM 6.0.0.8 on it. Then install CWM 5.4.0.4 followed by 6.0.0.8.
Now my problem is that any custom ROM I put on there just does a boot screen loop. I tried CM10 and the latest AOSP. To install the ROMs I just booted into CWM, installed the ROM from zip, then installed the gapps. I've tried with and without formatting the cache, user data, and Dalkiv, same results.
What am I doing wrong? I have loaded tons of ROMs on this before without any issues, then all of a sudden I can't get anything except official loaded.
Click to expand...
Click to collapse
did a format /system before installing the custom roms? This is an important step.
prince93 said:
did a format /system before installing the custom roms? This is an important step.
Click to expand...
Click to collapse
This fixed it. Never had to do it with any of my other devices. CM10 loaded quickly after that. Loving how fast JB is!
Thanks!
Sent from my GT-P7310 using Tapatalk HD
It worked
mobjunky said:
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Click to expand...
Click to collapse
WOw! This fixed my Tablet! thank you ever so much!!
mjramos15 said:
WOw! This fixed my Tablet! thank you ever so much!!
Click to expand...
Click to collapse
mobjunky said:
Hi Spazlon,
Sorry I'm not allowed to post links yet as I am also very fresh. But I've underlined the addresses so you should be able to find them
I just spent the best of 2 days trying to solve a similar issue - my 8.9 P7300 kept running in boot loop. It had been running ICS stable for several weeks, then suddenly started to loop boot for no good reason. Anyway - you need two programs installed on your computer as well as USB drivers for your tablet. The two programs are Odin and SDK developer package. Odin3 v 1,87 and 1.85 are found here: filecrop.com/Odin-1.87 - try some of the links, one of them should work without having to type a password. The SDK is found here: developer.android.com/sdk You can find more about how to use the developer package on that site as well, but I installed as support for Android 2.1 through to 4.1
Also install the USB driver files for your tablet on your PC. For example from here: xpdrivers.com/usb/_1_24.cfm?gclid=CL2iDs7MCFWF7cAodxFYANQ
You also need the following recovery files which you can find by searching the developer forum for galaxy tab 8.9:
ClockworkMod_Recovery_v5.5.0.4.tar
P73xx_Stock_Recovery.tar
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and finally a ROM of your choice, for example the ICS rom cm-9-20121028-NIGHTLY-p5.zip that I just used. You can find the latest official ICS ROM's here get.cm/?device=p5
Now - hold down the volume down button on one of the boot cycles. You should now get into a menu with two choices - Download and Recovery. Default is "Download" - if you press volume down you switch between the two choices. Press volume up to select the choice you want.
First you want to select the "Download" option. Then connect your tablet to your PC. The drivers should now install and your tablet should read that you are connected.
Now start Odin3. Click the PDA button and select your P73xx_Stock_Recovery.tar file. Then press Start.
Once finished the tablet will reboot, and you now need to once again get into the recovery menu. Now select the recovery option, not the download menu. You get into the stock recovery menu where you navigate with the volume buttons and select choices with the power button. Do a full factory reset and wipe the cache. WARNING - you will loose ALL your data, but it'either that or stick to a bricked tablet so.... You will also loose your root access,m which is why the next step is needed.
Now that everything is wiped clean you can use Odin again in "download mode" to install ClockworkMod_Recovery_v5.5.0.4.tar with the same procedure as before. You now have root access.
Reboot again and once again into the recovery mode (not download mode). Once you get into the CWM recovery menu you are ready for the final step, which is to install your new operating system.
Go to your SDK installation folder and find the folder named "platform-tools".
First you want to copy two files into this folder (provided you want to install Cynaogen Mod 9):
Clockwork_Recovery_6.0.0.8_GT-P7300.zip
and
Your ROM file of choice
Press shift and right-click in that folder and select "Open command window here". In the command prompt write
adb shell
Note - I had some problems here which was caused by lack of permissions. On your tablet in the CWM menu there should be a choice under the advanced menu for fixing permissions. Use that and you should be able to get into the terminal shell afterwards with the adb shell command
Now write the following command sequence:
• mount /data (don't worry if you get an error message - it means the folder is already mounted)
• cd /data
• mkdir media (if you get an error message saying the folder already exists, that's also OK!)
• exit
• adb push Clockwork_Recovery_6.0.0.8_GT-P7300.zip /data/media
Now you may have to wait a little while until your command prompt is back confirming that the file was uploaded.
Now on your tablet go to the menu point "install zip from sdcard" and find your CWM file that you just uploaded and run that.
Reboot once again into the "recovery mode" - we are now nearly finished.
Run the above push command again from the computer terminal window, this time to upload the ROM file you want to install. (the command is adb push [filename].zip /data/media)
Now on your CWM recovery menu once again run the zip file you just uploaded from the "install zip from sdcard" menu
When completed and you now reboot you should have a completely fresh android installation. Hope this helps.
Remember to mark this thread with solved if it works!
Thanks to kallt_kaffe and all the others who helped me through their various posts (hope that coffee isn't getting too cold again), as well as the following web sites that indirectly helped me resolve this issue googleymind.com/2011/11/guide-so-you-think-you-bricked-your.html#.UJUNN8XAd8G and galaxytabhacks.com/galaxy-tab-10-1-hacks/how-to-root-galaxy-tab-10-1-the-easy-way/
Good luck.
Click to expand...
Click to collapse
Gee thanks. This saved my tab. I'd almost given up on it and then voila.
Hi there, only just joined site as have had problem with this phone for a while now but left it alone untill my GF nagged me to try and fix it, but am very stuck and confused so here it goes....
the phone's carrier was virgin mobile so i downloaded an app to unlock it to another carrier but phone froze during process so had to power off and on the it got stuck on logo screen so some how i managed to install twrp v2.6.3.0 onto the phone but i am now just stuck here the phone now has no operating system and it showing internal memory as 0mb and i can only mount external SD.
Please if someone can help me i would be very very happy as its driving me crazy...serious.
Hope this post is in the correct section and any other info required i can give if needed.
Thanks in advance
John
johnlfc81 said:
Hi there, only just joined site as have had problem with this phone for a while now but left it alone untill my GF nagged me to try and fix it, but am very stuck and confused so here it goes....
the phone's carrier was virgin mobile so i downloaded an app to unlock it to another carrier but phone froze during process so had to power off and on the it got stuck on logo screen so some how i managed to install twrp v2.6.3.0 onto the phone but i am now just stuck here the phone now has no operating system and it showing internal memory as 0mb and i can only mount external SD.
Please if someone can help me i would be very very happy as its driving me crazy...serious.
Hope this post is in the correct section and any other info required i can give if needed.
Thanks in advance
John
Click to expand...
Click to collapse
if you've got a working CWM or TWRP Recovery then it should be easy to flash a new firmware onto the phone. I haven't done this but try the following steps :
1. Download this http://www.ipho9.com/install-dmod-custom-rom-galaxy-s3-mini-gti8190/ custom ROM
2. DO NOT extract it (keep the .zip file, well, zipped )
3. Copy/Paste the above .zip file to your external sd card
4. Start the phone and go to recovery (power+home+volume up buttons)
5. Choose install zip from external sd card
6. Find the .zip file that you just copied and select it
7. Now wait until it installs (can take about 10 mins or more - just be patient)
8. Reboot phone when the installation of the ROM is complete
9. Have fun with your completely new S3 Mini with a new great S4 look&feel
Hope that works !
koragg97 said:
if you've got a working CWM or TWRP Recovery then it should be easy to flash a new firmware onto the phone. I haven't done this but try the following steps :
1. Download this http://www.ipho9.com/install-dmod-custom-rom-galaxy-s3-mini-gti8190/ custom ROM
2. DO NOT extract it (keep the .zip file, well, zipped )
3. Copy/Paste the above .zip file to your external sd card
4. Start the phone and go to recovery (power+home+volume up buttons)
5. Choose install zip from external sd card
6. Find the .zip file that you just copied and select it
7. Now wait until it installs (can take about 10 mins or more - just be patient)
8. Reboot phone when the installation of the ROM is complete
9. Have fun with your completely new S3 Mini with a new great S4 look&feel
Hope that works !
Click to expand...
Click to collapse
1. Download this http://www.ipho9.com/install-dmod-custom-rom-galaxy-s3-mini-gti8190/ custom ROM
Click to expand...
Click to collapse
you can download every ROM you want for s3 mini (somin.n, Virginity, CM, ...) - steps 2 - 9 are the same
good luck
JackoMJ is right. I just posted the one i'm on 'cause i know that all the stuff are working
hello
I want install recovery on official V30C rom.
Please help me. thanks
Dr.Nexus said:
hello
I want install recovery on official V30C rom.
Please help me. thanks
Click to expand...
Click to collapse
I. Before You Begin:
1. You must have rooted your device before doing
this procedure. Check out our guide on how to root
the LG Optimus Black .
2. The following procedure works on Windows based
PCs only.
II. Downloading Required Files:
1. CWM Flasher (Download link’s given there in the
second step)
III. Installing ClockworkMod Recovery
on the LG Optimus Black:
1. Download the CWM Flasher Tool to your Desktop .
2. Unzip files from the Tool archive to your Desktop .
You will get a folder and about two files.
3. Turn ON the USB debugging option on your
device. To do that, head to
Menu>>Settings>>Applications>>Development>>USB
debugging and check-mark the box.
4. Connect the device to your PC using the USB
cable.
5. Next, double-click the file named flash.cmd on
your Desktop . You’ve extracted this file from the
Tool archive.
6. It should start flashing CWM Recovery on the
device.
7. When the recovery is flashed on your device,
double-click on the reboot-recovery.cmd file.
8. Your device should reboot in the Recovery Mode.
It confirms that the Recovery has successfully been
flashed on your device.
9. Done!
Awesome! With the one-click method, the CWM
Recovery was successfully installed on your device
in no time. Now, head to the custom ROMs
repository to find out the best custom ROMs for
your device!
press thanks if I helped you.
@SidDev said:
I. Before You Begin:
1. You must have rooted your device before doing
this procedure. Check out our guide on how to root
the LG Optimus Black .
2. The following procedure works on Windows based
PCs only.
II. Downloading Required Files:
1. CWM Flasher (Download link’s given there in the
second step)
III. Installing ClockworkMod Recovery
on the LG Optimus Black:
1. Download the CWM Flasher Tool to your Desktop .
2. Unzip files from the Tool archive to your Desktop .
You will get a folder and about two files.
3. Turn ON the USB debugging option on your
device. To do that, head to
Menu>>Settings>>Applications>>Development>>USB
debugging and check-mark the box.
4. Connect the device to your PC using the USB
cable.
5. Next, double-click the file named flash.cmd on
your Desktop . You’ve extracted this file from the
Tool archive.
6. It should start flashing CWM Recovery on the
device.
7. When the recovery is flashed on your device,
double-click on the reboot-recovery.cmd file.
8. Your device should reboot in the Recovery Mode.
It confirms that the Recovery has successfully been
flashed on your device.
9. Done!
Awesome! With the one-click method, the CWM
Recovery was successfully installed on your device
in no time. Now, head to the custom ROMs
repository to find out the best custom ROMs for
your device!
press thanks if I helped you.
Click to expand...
Click to collapse
Have to go into the recovery should all the work to be done every time???
Please give me link for that i need too install recovery.:good:
I am still waiting for the link
Dr.Nexus said:
I am still waiting for the link
Click to expand...
Click to collapse
for cmw recovery
https://play.google.com/store/apps/details?id=com.koushikdutta.rommanager&hl=en
for twrp
https://market.android.com/details?id=com.s0up.goomanager