[SOLVED] S Pen Screen Pressure - Galaxy Note GT-N7000 Q&A, Help & Troubleshooting

Does anyone know if there is a setting somewhere to increase the touch screen pressure sensitivity when using the s pen?
I have to press quite hard with the s pen (not when using my fingers) and am worried about damaging the screen. I've see other people using their pen much more lightly and the screen responds well for them.
I know there is a potentionometer (sp?) inside the s pen that is supposed to increase sensitivity but I'm not sure if it's the same as adjusting the actual pressure sensitivity. I've seen conflicting advice on whether the button should be turned clockwise or anti-clockwise. I don't get any ghost writing on my screen when hovering over it and the air view works as it should, it's just the amount of pressure I need to put onto the screen to make it work with the pen.
Also, does anyone know what the other button is for in the s pen? I mean the one farthest from the nib of the pen.
Thank you anyone who can help with this

Solved
If anyone is interested who has the same problem all I did was turn the second potentionometer 90 degrees anti clockwise. It was tricky as it's underneath the plastic clasp but if you use a small pin and take your time it eventually turns, little by little.
The first button seems to be for hovering sensitivity, the second is for pressure sensitivity. You can calibrate it to your liking.
Mine is working perfectly now.

Related

Pressure on the screen

Hey guys, there seems to be something a little irregular with the screen. When I press on the screen anywhere, there is a spot on the screen that appears to be what looks like pressure being exerted on it. Just like how it looks when you press on the LCD screen of a laptop. This happens also when i press on the case at the top on the left side. The spot I am talking about is about 1 in down from the top of the screen and about 1.5cm to the right from the left of the screen. It is not easily seen unless the screen is displaying a very dark background.
There is a membrane over the surface of the screen that will flex as any pressure is applied to the touch screen, both by the pen and by the frame. If you look at it through polarized sunglasses you can see the effect of any pressure quite dramatically. Unless the screen is malfunctioning or there is color distortion, I don't see a problem.
liquidsilver said:
There is a membrane over the surface of the screen that will flex as any pressure is applied to the touch screen, both by the pen and by the frame. If you look at it through polarized sunglasses you can see the effect of any pressure quite dramatically. Unless the screen is malfunctioning or there is color distortion, I don't see a problem.
Click to expand...
Click to collapse
i dont think thats what hes talking about, he makes it sound like whne he touches the screen a "lcd ripple" appears somewhere else on the screen.
Mine does this when i slide hte keyboard, i can see one in the middle, it kinda worries me, especially since my last kaiser's screen broke and i didnt do anything, i just took it out of my pocket and it was like that.

[Q] S Pen Calibration

My S Pen doesn't seem very accurate. When I touch the screen with it, it is off by a couple of millimeters. This is very annoying when drawing.
Is there a way to calibrate the screen/pen or something?
ltrulsse said:
My S Pen doesn't seem very accurate. When I touch the screen with it, it is off by a couple of millimeters. This is very annoying when drawing.
Is there a way to calibrate the screen/pen or something?
Click to expand...
Click to collapse
Well, that "problem" it isn't that. They need to do that because they want you to see the line that are you drawing.
If you enter in to the options of the drawing pen and change to left handed, you will see how that millimeters move to the other side of the pen. So, 1 2 up and 1 or 2mm left/right are necessary and it is how the wacom screens works. In other side I have tried a lot of wacom devices and this is one of the most accurate.
The only problem that I see it is the pen that if you don't give enough pressure it doesn't works, and if you give much, then it will writes in "bold" rather than skinny lines.
Try to move the pen without pressing it, only light slide and see how it doesn't do anything.
Other funny thing on the wacom devices is that the accuracy is not the same in the center of the screen and in the side of it. Problems of magnetism
Did you try pen pressure with autodesk sketchbook, is it working ?
Hi
Just a quick question for you who have the phone and use the pen. When you use your pen for drawing, what happens when your hand (which you hold the pen with) touches the screen? It must be annoying always to write without touching the screen with the hand/fingers like you would do if you were to write with an ordinary pen on a classic paper.
drelle said:
Hi
Just a quick question for you who have the phone and use the pen. When you use your pen for drawing, what happens when your hand (which you hold the pen with) touches the screen? It must be annoying always to write without touching the screen with the hand/fingers like you would do if you were to write with an ordinary pen on a classic paper.
Click to expand...
Click to collapse
The good thing is that u can touch the screen with finger when u write, unlike pure capacitive screen
If u touch the note with finger u will get a mark, ie u can use ur finger to write on the note
If u touch the area of screen above the note, the note app disappears to show the app beneath it and when u remove the finger the note comes back. This is to jot down things from the app beneath it. Hope this makes sense.
ltrulsse said:
My S Pen doesn't seem very accurate. When I touch the screen with it, it is off by a couple of millimeters. This is very annoying when drawing.
Is there a way to calibrate the screen/pen or something?
Click to expand...
Click to collapse
I'm curious, are you left handed?
There is a setting: settings -> pen settings -> dominant hand.
I changed mine to left handed (which I am), and when my right handed friend used it, he complained that it was off by a millimeter or too to the right.
- Frank
drelle said:
Hi
Just a quick question for you who have the phone and use the pen. When you use your pen for drawing, what happens when your hand (which you hold the pen with) touches the screen? It must be annoying always to write without touching the screen with the hand/fingers like you would do if you were to write with an ordinary pen on a classic paper.
Click to expand...
Click to collapse
Thats not an issue as when the pen is touching (so it's active), the screen will no longer accept any additional touches. So with your fingers, multi touch will be active for upto 10 (I believe) seperate touches at once, but as soon as the pen is touching the screen, it will only pick up the pen and no additional touches from your fingers etc so you can rest your fingers on the screen while you are writing.
Thanks for the explanation that makes sense nevertheless the offset is annoying and difficult to get used to.
Try this. It works for me.
http://jjpda.blogspot.com/2012/01/how-to-calibrate-galaxy-note-s-pen.html
try turn on the auto rotation
Or turn off auto rotation
Just try...
Actually all this is nonsense.
The offset is variable and depends on the angle of the pen.
The most simple way to test this and to get used to it, is to open
a S-memo. Then instead of using the line option you choose the
eraser option. Touch the screen and on the screen you see a circle.
Now with the pen on the screen change the angle of the pen and you will see
the tip of the pen 'move' inside the circle. Now get used to the angle of the pen
where the tip is in the center of the circle. Once you are used to this angle your pen will be dead on when drawing.
Remember way back when you learned how to write, it took you days to get used to holding a pen or pencil the right way.
I can recommend the official samsung s-pen holder for a much nicer feeling when using the pen.
Hope this helps
Keethos said:
Thats not an issue as when the pen is touching (so it's active), the screen will no longer accept any additional touches. So with your fingers, multi touch will be active for upto 10 (I believe) seperate touches at once, but as soon as the pen is touching the screen, it will only pick up the pen and no additional touches from your fingers etc so you can rest your fingers on the screen while you are writing.
Click to expand...
Click to collapse
I just want to clarify thhis, the pen needs to be touching and in writing pressure on the screen for it to stop accepting input from your skin.
friedje said:
Actually all this is nonsense.
The offset is variable and depends on the angle of the pen.
The most simple way to test this and to get used to it, is to open
a S-memo. Then instead of using the line option you choose the
eraser option. Touch the screen and on the screen you see a circle.
Now with the pen on the screen change the angle of the pen and you will see
the tip of the pen 'move' inside the circle. Now get used to the angle of the pen
where the tip is in the center of the circle. Once you are used to this angle your pen will be dead on when drawing.
Remember way back when you learned how to write, it took you days to get used to holding a pen or pencil the right way.
I can recommend the official samsung s-pen holder for a much nicer feeling when using the pen.
Hope this helps
Click to expand...
Click to collapse
Go to photo editor choose a bright picture choose the pen option from photo editor hold the phone on portrait mode and try to draw on the edge with a smaller tip on the pen then go switch dominated hand on spen and try again and then come back and say this isn't a devs calibration problem or coding or call it how you want. But give attention to
PHOTO EDITOR
PEN OPTION
PORTRAIT MODE
RIGHT HAND DOMINATED > RIGHT SIDE
LEFT HAND DOMINATED > LEFT SIDE
Sent from my GT-N7000 using XDA App
This idea that we need to see where we are writing is just as imbecilic as Motorola's idea of protecting users from rain drops. Back then, it stoped you from playing any games that required you to keep your finger stationary for more than 15 seconds. Here, it makes drawing and writing very difficult.
I don't ****ing see where I'm writing when I'm using a paper, why would I need that on my phone's screen?
I have also problems using my spen. Is it realy normal to put quite much pressure on the pen to write sth.? It's realy hart to dram thin lines without any interruption of the line..... feels as if that'S not "normal"
how about yours? Is that normal?
I don't know if this will help, but my s-pen was off a few millimeters too after an official update. I tried calibrating the accelerometer and gyro and the s-pen became accurate again. I'm not sure though if this indeed did the trick or if my mind was just playing tricks on me.
Thanks, I'll try that, too. But my Problem primarily is not the millimetres off, it's the pressure needed to draw sth.
I also wrote Samsung's support yesterday. I'll see what they say.
I won't flash my phone before I can be sure that it's okay and I don't have to return it.....
Matrox182 said:
Thanks, I'll try that, too. But my Problem primarily is not the millimetres off, it's the pressure needed to draw sth.
I also wrote Samsung's support yesterday. I'll see what they say.
I won't flash my phone before I can be sure that it's okay and I don't have to return it.....
Click to expand...
Click to collapse
iam having the exact same problem..please tell me if you find a solution.
it didnt happen with the pen which came with phone..it had the millimeters away problem..and when i lost i ordered new pen this new pen has more pressure problem..its very hard to draw thin lines
friedje said:
Actually all this is nonsense.
The offset is variable and depends on the angle of the pen.
The most simple way to test this and to get used to it, is to open
a S-memo. Then instead of using the line option you choose the
eraser option. Touch the screen and on the screen you see a circle.
Now with the pen on the screen change the angle of the pen and you will see
the tip of the pen 'move' inside the circle. Now get used to the angle of the pen
where the tip is in the center of the circle. Once you are used to this angle your pen will be dead on when drawing.
Remember way back when you learned how to write, it took you days to get used to holding a pen or pencil the right way.
I can recommend the official samsung s-pen holder for a much nicer feeling when using the pen.
Hope this helps
Click to expand...
Click to collapse
This is absolutely correct... the stylus orientation definitely does affect the point offset.
The problem is (at least on mine) is that the "left-handed" setting appears to do nothing. The point offset is the same regardless of the setting (it's biased for right handed), so trying to write left handed is very hard.
How many people that are having the problem are 'lefties'? If I pretend to be right handed, the offset is perfect (regardless of the left or right setting). This has to be a bug and I'll presume it'll get fixed soon. Because it's really quite intolerable as a leftie.
Today I upgraded my phone to Criskos rom with Abyss kernel and all accuracy problems are gone for me.Never had problem with pressure.
Sent from my GT-N7000 using Tapatalk

Screen Distortion / Ripple

Does anyone else have this problem:
When you're just pressing a bit harder than the usual touch, on the top and bottom Left side bezel, it causes the Screen to ripple (fluid wave effect).
Not even pushing down too hard, just a firmer press than usual. This is easy too see on a darker background, like the default background when the device wakes up and still in locked mode.
Yes I realize it's a LCD screen, plus this Corning glass is thinner, and we're not always pressing it that hard to notice anyway.
But the Right side bezel and other areas are mostly fine,
So I'm wondering if it's a defect on my device or not (the left side being too sensitive)? would this cause further problem in the future? And it could be a concern if I carry the Nexus 7 in the backpack and other items pressing on it.
Other reports on this:
http://www.theverge.com/2012/6/29/3125396/google-nexus-7-review
"the display can give a little and cause the LCD to ripple if you really press hard against the screen"
http://forums.androidcentral.com/google-nexus-7-tablet-forum/191040-screen-distortion.html
I wonder if I try the Fix on the other thread, taking off the cover, but instead, loosen the screws a bit on the left side, would that help?
Thanks!
Hi,
My device has this too. Mostly on the left side & a little less on the right side but hardly any on the top or bottom.

Is my s-pen broken?

Hi guys
I just got an second-hand note and i'm wondering, is my s-pen broken?
I know that it registers multiple levels of pressure, but i can't seem to figure it out.
I know the note app makes a thicker line when u press harder, but i can't seem to get it to work.
Also, i cant "feel" the tip going "up" a little bit. I can imagine for diferent levels of pressure the tip moves a bit up and down, but i cant feel it. It feels like it is stuck.
Is it broken or is it supposed to do this?
I mis-click sometimes (i clearly touch the screen but it doesn't register) and the "sync" is way of, like 2 mm to to the top and left.
Any ideas?
Thanx!
Check with another pen.
Sent from my GT-N7000 using xda premium
my spen is fine and i dont find the tip moving at all. it works just fine.. on the snote app try with a brush instead of pen.. that should a better picture of pressure sensitivity
Hmm i tried it but it goes from thick to not registering the stylus (as it is clearly on the screen)
Do u guys get feedback when u let ur pen "fall" on the screen? with this i mean it is bouncing on the screen, with only its own weigt. I can go as high as i want but when it touches my screen i wont get feedback. I need to press it myself, on top of the weight of the pen.
Also the position is off. Any way to calibrate this? Or is it my pen? And if it is the software, wil flashing a new rom fix it?
i dont know about any feedback..
i have read and seen some apps that can calibrate the spen by just changing the spen settings dominant hand to left then to right,
In papyrus the line should get thinner when less pressure is given.
so i finaly figured it out. in papyrus, it is clearly noticable that when i press harder i get a thicker line.
What i do notice about the allignment is that when it is on righthand mode the cursor is off somewhat to the up-left side, and on lefthand mode it is to the up-right side. I found that this is because it thinks i want to hold the pen with an angle. If i do that (as i just found out) it alligns just fine. But i want to be able to use it 90 degrees from my screen, straight. Is there any way i can fix this? Because i think the screen is reporting the right position only the left- or righthand mode is correcting it.
i think its made to use it in an angle.. that why the hovering icon aligns just right at a slant
My stylus is registering the pressure input plus it wont go thicker than the ppont u selected. The thickness is only apparent when u use a thick bruah. So check it again.
Sent from my GT-N7000 using xda app-developers app
Fixed
Got a new s-pen, "problems" still exists, so i think its just how s-pen works, not exactly as i want it but will do fine.
Thanx everyone

S-Pen Over Sensitive

My S-Pen is over sensitive. It activates when it's very close to the screen or when I barely touch the screen briefly. Very annoying. I have a tempered glass screen protector but still it's over sensitive. I have seen many solutions to increase sensitivity, but not to decrease it. Is there solution for this?
Did you increase the sensitivity because of the screen protector? Is is better, for spen at least, if the sensitivity is on default setting?
Define, "activates." What does it do?
With default settings, and a glass screen protector, my phone recognizes the S Pen when it is within 12mm - about 1/2 inch - from the screen. That's when the little circle appears, and the Air Command button highlights (for example). I rather think it's supposed to work like that. You shouldn't need to touch the pen to the screen or apps like Glance wouldn't work.
The s-pen detects pressure by sensing how hard the nib is pressed, thus the phone can recognise by determining where the pen is on the screen and the pressure exerted (you can test this by pressing the nib with your finger, and hover your s-pen on something you want to click)
You could try removing the nib and re-inserting it back, if that helps
raul6 said:
Did you increase the sensitivity because of the screen protector? Is is better, for spen at least, if the sensitivity is on default setting?
Click to expand...
Click to collapse
No, the Touch Sensitivity is turned off in Settings.
RGardner said:
Define, "activates." What does it do?
With default settings, and a glass screen protector, my phone recognizes the S Pen when it is within 12mm - about 1/2 inch - from the screen. That's when the little circle appears, and the Air Command button highlights (for example). I rather think it's supposed to work like that. You shouldn't need to touch the pen to the screen or apps like Glance wouldn't work.
Click to expand...
Click to collapse
By activate, I mean it will launch apps on the home screen, open links in by web browser, etc. I get the little circle when my S-Pen is close to the screen and it works as it should. That's not the problem.
n1Bb135 said:
The s-pen detects pressure by sensing how hard the nib is pressed, thus the phone can recognise by determining where the pen is on the screen and the pressure exerted (you can test this by pressing the nib with your finger, and hover your s-pen on something you want to click)
You could try removing the nib and re-inserting it back, if that helps
Click to expand...
Click to collapse
I tried replacing the nib, but it makes no difference. I have a second S-Pen that came with the phone and it does the same thing. So, I don't think it's the S-Pen that is the problem, it's the sensitivity of the screen.

Categories

Resources