[Q] i9000b won't flash "Odin Xmitdata Fail" device bricked - Galaxy S I9000 Q&A, Help & Troubleshooting

hi there..
since i bought my phone it never got a firmware update, neither OTA nor a manual one. It came and stayed with android 2.2 with all these years.
Now that i am more into android i decided to use a custom rom, this one = http://forum.xda-developers.com/showthread.php?t=2012061
But before flashing this rom i had to flash it with an official 2.3 rom, since it was one of the requirements and it still had a 2.2 in it.
I went to samobile, grabbed this rom http://www.sammobile.com/firmwares/3/?download=4340, plus a .PIT that was necessary according to the tutorial i was following.. and on the first attempt i got the error and the device got bricked.. So i tried, and tried, and tried... but i always end up getting the same error within Odin. This one:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> __Xmit Write fail
<ID:0/004> XmitData Fail..
<ID:0/004> Complete(Write) operation failed.
The device is now bricked, i can't even enter in downloadmode anymore, so i bought a USBJIG to enter in downloadmode and it works, but i still get the same error when trying to flash. I've tried dozens of different roms (of course all of them were made for this device), different versions of Odin, different USB port, Samsung Kies is installed but it is completely closed. I don't know what else to do, i need help... Please help?

xcaninox said:
I've tried dozens of different roms (of course all of them were made for this device), different versions of Odin, different USB port, Samsung Kies is installed but it is completely closed. I don't know what else to do, i need help... Please help?
Click to expand...
Click to collapse
you cannot use i9000 ROM's only i9000B ROM's, you need to kill KIES , Open task manager and close these : Kies.exe , KiesTrayAgent.exe, and KiesPDLR.exe
preferably use Odin 1.85 or 3.04
FIRST STEP for ALL Problems:-
Whenever you have a problem with your Phone, power it down, remove battery, remove SIM card and Ext SD card and press and hold your power button for at least 30 seconds to a min, before reinserting battery and trying any solution
First reboot PC after a power cord unplug and also reboot the Phone after a battery pull. Always use a Fresh Odin after any attempt to flash, than make sure you "Uncheck Repartition", If you had checked it or clicked PIT when you are not using one. You should also be running Odin as an Admin and ensure that KIES is not running when using Odin. Most of all, only use Samsung USB cable and not others as they may be incompatible and trying it out on a lap top or another PC ( when it happens repeatedly)

i discovered what was causing the error. it was Windows 8, samsung drivers are not working correctly on it, i don't know if this is a localized or a global problem... my guess is it is a global one
i had Kies installed in windows 8,and all its process were killed before flashing pretty much on all of the time i was trying to flash.
yesteday by pure luck my sister came to my house for a visit, and she had hers notebook with her that btw has windows7, so i decided to try flashing the phone through it, i grabbed it installed samsung drivers and didn't install Kies, surprisingly, for me at least, the flashing went perfectly OK on the first attempt.
after the flash i had one error, "couldn't mount db/data", i googled it and easily fixed it already, but that is another thing for another thread.
thank you for helping

xcaninox said:
i discovered what was causing the error. it was Windows 8, samsung drivers are not working correctly on it, i don't know if this is a localized or a global problem... my guess is it is a global one
Click to expand...
Click to collapse
All PC's running any version of windows seem to get USB connection problems at one time or the other But lap tops and notebooks seldom have this problem.

Related

Galaxy Tab dead!

Hallo,
sorry for my bad English. I have translate my Problem with promt . I have flash my Tab with JM6. After the flash my Tab do not boot. On the tab is a picture, a yellow triangle and a PC are indicated. Get with Odin 3 1.7 following error message.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Have you tried recovery
Sent from my GT-I9000 using XDA App
thank you for your answer.
no, what must i do?
wheel14 said:
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Click to expand...
Click to collapse
after you're flashing with Odin, then restating automatic in download mode, press the power button for 10 seconds (until tab will switch off), then restart by pressing the power button together with volume up. wait until finishing installing of CSC and then will restart by it self.
check my tread
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
wheel14 said:
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
Click to expand...
Click to collapse
I had the same situation, just take a look here. try to don't panic... try to follow my steps described in the tread and you might be succeed. I hope it help
I do not look though there sorry. I am in panic..which step....is the right?
i have flash the pit-file only. ist this right? and now?
wheel14 said:
I do not look though there sorry. I am in panic..which step....is the right?
Click to expand...
Click to collapse
try to look here and here
thank you.. I have flah the pit File only. now i will flash the pda without the pit. re-partition will be not selected. is this right. thank you for your help
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
wheel14 said:
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
Click to expand...
Click to collapse
I can't get you....can you describe a little what have you done? you're saying that you flash the firmware with Odin, right? and then? have you restarted in recovery mode? or you boot the phone loading the OS.....you should restart directly in recovery mode in order to finalize the installation of PDA and CSC....
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
wheel14 said:
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
Click to expand...
Click to collapse
Welcome back in our family.
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Go to samfirmware.com download the files for your device.
Select pit file then check repartition - flash
Select pda csc modem, uncheck repartition - flash.
Good luck! If you get any trouble send me a msg. on skype luc_de_mar
khatypically said:
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Click to expand...
Click to collapse
Sent from my GT-P1000 using XDA App
Thanks Lucian, This is exactly what I did in the first place. Used Odin 1.7 and applied the PIT file coming with it, then applied the P1000JPJM5 PDA and CSC modem file.
Unless the P1000JPJM5 is not for my device?? How to know?
Lucian, any clue?
My tab is dead after I tried to install an arabic firmware from samfirware.com. I bought my tab originally from the US. Now, I'll download the "suitable" firmware from samfirmware.com as you advised, but How would I ever know the suitable firmware given that my device is exactly this one (that's where I bought)(my devise is dead now and can only display the download mode):
www .amazon. com /GALAXY-TAB-P1000-16GB-UNLOCKED/ dp /B004AKOVIS/ ref=sr_1_1?ie=UTF8&s=electronics&qid=1305378100&sr=8-1
Regards,
Khatypically, alive with a zoombie tab
totally unresponsive tab
I have been searching around forums looking for advice and have been unable to locate a solution so here seems as good a place as any to ask for help. I have an unlocked gtp-1000 that has been running overcome 1.4.5 for last month very nicely until tonight when I thought it would be a good idea to get some gingerbread goodness like I have been using on my nexus one. was going to flash Overcome ROM v2.0.0 BETA 2 and was following guide but only got halfway through flashing stock gingerbread with odin when laptop unexpectedly did a restart for an unknown reason while I was away getting a snack. was unsure whether flashing process had been completed so opened odin again and tried reflashing. couldnt get past
setup connection...
so tried to reboot into download mode and then powered down. now tab is dead. battery was at 80% when it died
before I take back to samsung tomorrow any ideas?
I have plugged into wall charger= nothing
plugged into laptop=nothing and not detected
held power and volume up=nothing
held power and volume down=nothing
held power and volume up & home=nothing
no sounds or anything at all on screen
truly bricked?
Updates:
Hi Guys,
I applied the p1000nubjm2 firmware. I downloaded it from samfirmware. It's the latest P1000L firmware for America/Australia. It failed in the PDA file: P1000NUBJM2_P1000NUBJM2_P1000NUUBJM2_HOME.TAR . I was planning to apply the gingerbread update after that.
Now to the results, As you know, before, I was able to reach the download mode, the startup Galaxy Tab/Samsung screen, and the battery displays when connecting the cable. Now, after application of this lovely firmware and failure, nothing (literally "Nothing") takes place. The device became more dead than it was before . It doesn't display anything and it doesn't respond to power or displays the battery. It became a black $500 cost brick No matter how much time I keep it charging (or what "should be" charging), it would never startup again (sigh!) The ODIN and samsung kies no more recognize the device when connected to the computer.
Any additional clues before I decide to convert it to a teacup base?
Regards,
ARK

How to Flash a Kernel

how come when i d/l a kernel
I897UCKJ3 Android 2.3.5 Gingerbread
Stock
from http://forum.xda-developers.com/showthread.php?t=1300843
it's a 6mb file or something. How do i use a .tar? I tried opening Odin 1.85. but what do i load it as? PDA, PHONE?
Sincerely,
Semi-confused
like Boog's KJ3 Kernel. I don't have CWM, so i need to flash that kernel to move on with Illuimance. But how do i used ODIN to do that?
Place kernel in PDA and hit start. (MAKE SURE repartition is UNchecked).
i did, but it doesn't do anything to the phone.
Debugging or DL?
ODIN recognizes phone in debugging, but not DL mode for some reason...
repartition unchecked, and the .tar loaded to PDA slot.
i click start, but it just says (.../failed 1)
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<OSM> All threads completed. (succeed 0 / failed 1)
Put your phone in download mode first.
You have to be on download mode. Try rebooting your computer or using main USB port. Also checking drivers and cable also helps.
sent from awesomness
U have to be in download mode. Right click on Odin and run it as admin, also if it still fails try a different primary usb port (1st one on a laptop or the ones in the back of pc that connect to the motherboard). Removing sdcard (if u have one) and sim wouldn't hurt if ur still facing issues.
Dang it viny beat me to it
i run "I897UCKJ3 Stock without BL" as admin
i put phone in download mode (hold vol + and -, plugin usb, put in battery)
but nothing happens with ODIN
i changes USB ports, and now it shows up in ODIN. But it is stuck at :
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
ccamwilkins said:
i run "I897UCKJ3 Stock without BL" as admin
i put phone in download mode (hold vol + and -, plugin usb, put in battery)
but nothing happens with ODIN
Click to expand...
Click to collapse
Do U see a yellow indicator on Odin saying something like COM6 or some other number? If not than Odin is not seeing ur phone....high chances of faulty data cable...happened to me....i changed the cable worked like charm
EDIT: Even the above scenerio can be caused by faulty cable
yeah it sees it as COM5.
i plugged the phone in (download screen didn't pop up) but ODIn still recognized it, i hit start, and it's working now (just a blue status bar progressing across the bottom) So i guess it's going to work now? odd...
thanks though. I've had crazy misfortune with this phone so far.
yep... working like a charm. (finally)
Don't get me wrong, we are glad to help you and everyone else, but pls do a lil reading before u start flashing things next time (for your sake). These questions are answered almost if not daily, the first 2 pages usually have ur answers, if not then use the search button.
yes... it is working

[Q] Samsung Galaxy S won't come on after flash

Hello All,
I tried flashing my phone (to I9000XXJVS)
I've only gotten to step 11, which flashes the phone.
In ODIN, I selected PIT, PDA, PHONE and CSC. All 4 had files.
I selected the following options:
Re-Partition, Auto Reboot and F. Reset Time
While flashing, I got the following messages
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> factoryfs.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> cache.rfs
<ID:0/005> zImage
<ID:0/005> modem.bin
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/005> Removed!!
I switched off the phone and tried to turn it back on.
It won't come one at all. It's not showing anything.
It won't even go into recovery mode.
It won't go into download mode.
Pls help.
Take the battery out for 15 minutes and then replace and see if it powers back on.
If it still wont turn on or go into download mode using the key combination then try using a USB JIG.
What rom did you try flashing?
I'm trying to go to Gingerbread 2.3.5 I9000XXJVS.
I waited 15 mins. Still nothing.
Even when I put in the cable through USB, nothing shows up. Normally it shows that it's charging.
See screenshot of my ODIN configuration while flashing:
Try and plug your phone into the PC and then try the 3 button combo with the cable attached.
No difference. Still won't come on.
I hope the board is not fried.
Very strange...
I cant view the image you posted at the moment to see if files were put in the right places because im on works ancient internet browser but from what you wrote in the OP the flash appears to have gone ok...
Might be worth getting a JIG and trying that. If that doesnt work maybe its time for the unbrickable mod.
REALLY stupid question but you have flashed the right firmware for your device right?
I would give the JIG a try. You can buy one from ebay for like less than £5 GBP or you can throw one together youself.
Did the phone reboot fully after the flash before you turned it back off?
Yes, the flash went OK.
What do you mean by the right firmware? I got the firmware from samfirmware. I actually new to this.
And what's a JIG? How do I put one together?
The phone didn't reboot. The screen was blank but kinda slightly lighted. So I tried powering it up but it didn't so I removed the battery.
I got the JIG. I'll try to build one myself.
I'll let you know if it works.
One more thing: the battery was kinda low when I started this operation.
I'm thinking maybe the battery ran out.
But it's not even charging when I plug it in.
What i mean is do you have an i9000 and not an i9000M or another variant of the i9000 and have tried to flash a firmware from an i9000 onto an i9000M or i9000B for example.
I wish i could see that picture you posted to have a better look.
In the PDA box you should have had a file called PDA or CODE... The modem box should have had MODEM or PHONE... and then CSC should have had CSC...
There should have been a PIT file in the PIT box...
You should have had repartion ticked... auto reboot ticked and auto F reset ( ithink its called that ) ticked.
The update bootloader and other check boxes that are below the 3 i mentioned should all have been unticked.
I use a GT-i9003
in PDA i have CODE...
in PHONE i have MODEM...
in CSC i have GT...
in PIT i have a .pit file
I had all three boxes ticked (Re-Partition, Auto Reboot, F. Reset Time)
All other checkboxes were unchecked.
It looks like you have flashed incompatible firmware onto your device.
You have flashed firmware for the i9000 which wont work on the i9003.
You have gone into the wrong section on Samfirmware.com. There is a seperate section for the i9003.
You can still try the JIG trick but im not sure if that will work either on your device as the hardware may be slightly different and require a different resistor value to force download mode but im not sure about that part...
It looks like you have flashed bootloaders onto your device that wasnt designed for it which could mean a hard brick.
Maybe the unbrickable mod will help you out.
Im not too sure how to help you from this point on im afraid if you cant get download mode working...
Have a good search through google and see if you can find any helpful information.
Other thing is to say you had an update for it and it broke your phone and try and play dumb and see what happens =/.
I hope you can get it sorted mate.

Need Help with Samsung Brick Issue

Hi,
I am from UK and am a complete and utter noob and not very technical at all.
I bought an SGS GT i9000 and it already had 'Darkys ROM' installed. (I just thought that was normal). The phone worked well etc and a few days later since the phone was second hand I came across a 'factory reset' option and then the phone never worked again.
Got stuck in a boot loop so I read.
Also my phone will not enter download or recovery mode using the 3 button procedure so I purchased a 'jig' off ebay. It will now go into download mode upon inserting the jib.
I tried to recover the phone by following: http://forum.xda-developers.com/showthread.php?t=1802778
I completed all the steps but it made no difference to the phone. It still gets stuck in the boot loop.
Can anyone recommend a guide for me? I have seen others but cannot follow them as they often use too much jargon.
Furthermore, if possible I would like to just put my phone back on to a stock ROM. But I will do anything just to get it back working again and cross such bridges once it is up and running!
All help is really appreciated.
cheers
Furthermore,
Odin output (from following the xda guide linked above):
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> Removed!!
Odin resets the phone after the firmware update start and then it gets stuck in the same loop again. The four colours coming together to form an x-shape (red, yellow, green and blue).
After which the phone starts up and gets stuck in the boot loop where it was getting stuck previously.
Can anyone point this noob in the right direction please?
thanks
sbow1 said:
Can anyone point this noob in the right direction please?
thanks
Click to expand...
Click to collapse
Check Here to chose your forum/Guide by Version of your phone or you will have more problems by using wrong solutions due tio differnt versions of Galaxy S
But First powerdown, pull out Battery, SIM CARD, and EXT.SD card, press power button for a minute, than powerup without SIM and Ext.SD Card...make sure you have more than 50% battery charge before you attempt any sort of flashing.
Odin will get stuck for two reasons 1) KIES is running in the background of your PC or 2) the files you downloaded are corrupted
Look at the solutions thread for answers and collections thread for rescue kits
you can get a rescue kit from My Android Collections and or a solution from My Android Solutions
Hey
try to upgrade to 2.3.6 (link below) after applying the JIG..plus make sure that u have the SGS drivers installed and KIES IS NOT RUNNING...
checkout video guide for bricked sgs gti9000 on youtube puggereduk.com
here try this i made it myself just read the readme and follow. works for me everytime
http://www.mediafire.com/download.php?34oxweahfpy53dj
I agree with the recent posts, you need to follow a guide on how to flash a stock rom through Odin. Good luck flashing!

Software broken samsung galaxy s1 (i9000)

3 things for I start 1 I'm bat in English because I'm dutch sorry for that if you don't understand a sentence just ask I will try to explain it 2 I'm also bad in making sentences that's why you don't see any dots Sorry for that to and the third thing is I'm not at bad at rooting or installing custom roms did it on my galaxy tab 3 no problems also on my cousins phone also no problems same as that from my mother.
I have for a long time my galaxy s1 like 3 years now I had it rooted and installed the Cyanogen mod (nightly form the 5th of April) and it was jut working fine I just update once in the moth or so always the lasts nightly but when I did updated for the newest nightly for that day (11th of may update) and when it restarted it was just stuck at the boot screen so I got the battery out waited 5 minutes and put it back in end reboot it did that like 3 times but every time it was stuck at the boot screen so I searched on Google but nothing works because Odin(3.0.7 also 3.0.9) fails to make connection or it was stuck at the nand write start
all what I tried was in the odin:
use an other cable
other pc / laptop
other usb ports (used always the back of the pc)
other packages for odin
other odin versions
I also tried using heimdall also no success
and after trying this all my phone even get worse when it was stuck i can only access download mode
recovery wasn't able any more so I also set the root package not on the pda from odin but on phone and when i booted the phone I get into an old recovery of cwm but he was not able to mount my storage or something else after just trying around with odin and a little heimdall no success now I can only access download mode and odin sees my phone but it doesn't matter where I put any package it just loads normal and when it needs to reboot it is just black screen it makes connection but it stops if I put the root package in the pda or a phone package in the phone sections then it stops at nand write start I tried to re-partition it with different pit files but also no success
*edit a friend said ty using odin 1.3.0 but now odin said this
<ID:0/012> Added!!
<ID:0/012> Odin v.3 engine (ID:12)..
<ID:0/012> File analysis..
<ID:0/012> SetupConnection..
<ID:0/012> Initialzation..
<ID:0/012> Set PIT file..
<ID:0/012> DO NOT TURN OFF TARGET!!
<ID:0/012> Can't open the specified file. (Line: 1455)
<OSM> All threads completed. (succeed 0 / failed 1)
if I do a root package in pda or phone
* edit
I fixed it just do this
http://forum.xda-developers.com/showthread.php?t=1583026
except for the voodoo kernel part its was stuck at boot screen hear only a women talking cant under stand it because my speaker in my phone is messed up
if you want to root it use this package http://download.chainfire.eu/132/CF...XA_JVU_2.3.6-v4.3-CWM3RFS.zip?retrieve_file=1
so maby you People can help me
Thanks for any help that comes

Categories

Resources