Related
Hello everyone
So a couple weeks ago I took a unexpected swim with my Nexus 6 in my pocket, and haven't gotten it to work since. When I got out I immediately took the phone out of my pocket and turned it off, only to have it boot back into fastboot a few seconds later, turn off, boot to fastboot, and turn of again. It did this several times till it just stayed off. I took it apart, dried it, and cleaned it in Isopropyl alcohol and tried to turn it on but got no response no matter what I did. :crying:
I would consider it fried except whenever I plug it into my charger, the charging icon comes up like normal and even does the battery filling up animation. I replaced the power/volume button strip inside the phone hoping that it was the only problem, but it still would't turn on. I haven't replaced the battery yet because the charging animation shows it's holding charge, but loosing 40ish% after a week and a half of sitting there.
So is there something else I can do, or is it fried? I'm probably going to get a new battery to see if that improves anything, but I honestly don't know what more to do. If anyone has any ideas, I'd love to hear them.
Thanks in advance!
It's fried. Best you can do is send to shop and see if they can salvage it.
Alright, I'll guess I'll have to do that. Thank you for your reply.
I would like to share photos of my phone and seee if anyone vcan help, my situation is kind of similar. I tried to charge after to days of silica drying and cleaning with IPA.
I thin the connection around the battery area isn't secure. Is there a glue that i could buy?
The only thing a shop may do, is give it a bath in a ultrasonic machine, and bake the board. Try a new battery, internal batteries never do well in WD.
oOflyeyesOo said:
The only thing a shop may do, is give it a bath in a ultrasonic machine, and bake the board. Try a new battery, internal batteries never do well in WD.
Click to expand...
Click to collapse
How about sticking the charging coil to the new battery? What type of adhesive is needed?
uncle_buckman said:
How about sticking the charging coil to the new battery? What type of adhesive is needed?
Click to expand...
Click to collapse
You may still have enough adhesive left over on the coil to stick it to it. Otherwise it doesn't matter much, as long as its connected and not crazy loose, the frame will hold it in place.
oOflyeyesOo said:
You may still have enough adhesive left over on the coil to stick it to it. Otherwise it doesn't matter much, as long as its connected and not crazy loose, the frame will hold it in place.
Click to expand...
Click to collapse
I got it kind of working, but the sound is fuzzy and the screen is flickering a little.
I'm missing some screws, so I'll need to buy some new ones.
T3/M3 torx screws, 2mm/3mm height/diameter?
Hello all!
I've been very pleased with my new Nexus so far, but yesterday I noticed the back cover was loose and and had a bit of a gap near the volume buttons. Some quick googling informed me this was a known issue, and is easily RMA'd. I have also discovered there are some very nice skins from Slickwraps and from Toast which can be used in place of the back cover. I find these to be very beautiful, and will most likely use one. Knowing this, is there any useful reason to send my phone in to be replaced? Has anyone discovered a flawed battery causing the cover to lift? If so, was it obvious before removing the cover?
I would be afraid that if I didn't get the phone replaced, it would leak if you ever got around water. I think I would send it back because if you ever decide to sell it you won't get much for a phone that doesn't have a tight fitting backup cover.
Sent from my Nexus 6 using Tapatalk
dalegg said:
I would be afraid that if I didn't get the phone replaced, it would leak if you ever got around water. I think I would send it back because if you ever decide to sell it you won't get much for a phone that doesn't have a tight fitting backup cover.
Sent from my Nexus 6 using Tapatalk
Click to expand...
Click to collapse
Those are both good points, but they are somewhat nullified by my plans. I'm going to be removing the back cover to use an aftermarket back. I will, of course, be fully responsible for protecting it from water, and for the damage if I don't. I tend to treat any device, water resistant or not, as if it were the Wicked Witch of the West and will melt upon contact with a drop of water. I also don't sell my old phones. They are way to useful to keep around for projects and such. I still have a couple of Blackberry Storms acting as desk clocks and a Galaxy Nexus doing tattle-tail duty for my home alarm system.
Basically what I'm looking for is any indication as to an actual malfunction being the cause of the back coming unstuck. As it stands, the loose back is a head start on getting it off for an aftermarket.
I say go for it as long as the new back cover fits tight. I am a snob about having a perfect phone.
Sent from my Nexus 6 using Tapatalk
Most the skins cover the back cover so need an intact backcover or have the same problem. Will see when remove back cover if it is battery related but then most likely can't RMA as you opened the device. It a catch 22 situation.
prdog1 said:
Most the skins cover the back cover so need an intact backcover or have the same problem. Will see when remove back cover if it is battery related but then most likely can't RMA as you opened the device. It a catch 22 situation.
Click to expand...
Click to collapse
I'm looking at the wooden covers. They're a bit thicker then the vinyl skins, and can sit flush with the frame when used without the back. They're rigid enough to do the job, though not advertised as backs, folk are reporting having success.
I am tempted to open it up and have a peek at the battery, but doing so would definitely void the warranty. That's why I was looking for any examples where a battery actually has gone bad. Though, it looks like the battery is pretty simple to replace anyway...
hawkjm73 said:
I'm looking at the wooden covers. They're a bit thicker then the vinyl skins, and can sit flush with the frame when used without the back. They're rigid enough to do the job, though not advertised as backs, folk are reporting having success.
I am tempted to open it up and have a peek at the battery, but doing so would definitely void the warranty. That's why I was looking for any examples where a battery actually has gone bad. Though, it looks like the battery is pretty simple to replace anyway...
Click to expand...
Click to collapse
Usually swells up in the middle and starts raising the back at the mid points.
prdog1 said:
Usually swells up in the middle and starts raising the back at the mid points.
Click to expand...
Click to collapse
Does it feel swollen? Can you tell by eye? The only ones I've witnessed having a dying battery had removable battery covers, like the Storm and the old Razr flip phones. My cover is only loose on one edge, and feels very firmly stuck the rest of the way around. The phone itself is functioning beautifully, not at all like the few I've seen the the grow-a-battery of death. They usually sputtered and gave up until I replaced the battery.
hawkjm73 said:
Does it feel swollen? Can you tell by eye? The only ones I've witnessed having a dying battery had removable battery covers, like the Storm and the old Razr flip phones. My cover is only loose on one edge, and feels very firmly stuck the rest of the way around. The phone itself is functioning beautifully, not at all like the few I've seen the the grow-a-battery of death. They usually sputtered and gave up until I replaced the battery.
Click to expand...
Click to collapse
If it's the battery will do the same. Will start acting up and then die. There is a thread somewhere in General I think with pics of expanding battery. Some just the backs come unglued. It is definitely a RMA situation anyway.
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Droidriven said:
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Click to expand...
Click to collapse
Already search extensively, no luck so far. Prefer not to 'experiment' and wreck the thing!
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Bro check YouTube very well... it there
Sent from my iPhone using Tapatalk Pro
I can help you.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Did u fix it? I can help you. I opened the phone like 10+ times.
Hi, I have the same problem, I need to open the phone to replace the camera but did not manage to find anything on youtube. Would u please help me? Thanks
Monster 00 said:
Did u fix it? I can help you. I opened the phone like 10+ times.
Click to expand...
Click to collapse
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
kiwironnie said:
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
Click to expand...
Click to collapse
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Monster 00 said:
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Click to expand...
Click to collapse
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
kiwironnie said:
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
Click to expand...
Click to collapse
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Monster 00 said:
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Click to expand...
Click to collapse
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
kiwironnie said:
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
Click to expand...
Click to collapse
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Monster 00 said:
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Click to expand...
Click to collapse
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
kiwironnie said:
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
Click to expand...
Click to collapse
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Monster 00 said:
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Click to expand...
Click to collapse
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
kiwironnie said:
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
Click to expand...
Click to collapse
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Monster 00 said:
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Click to expand...
Click to collapse
Brilliant, thanks again! No need for a video, as your explanation is very clear and should be obvious to others after they get the back off the phone. Having recently removed a glued battery from a Kindle, it was a hell of an arm wrestle! Hopefully it will be a bit easier with the Y6. I have a flat nylon spudger with a rounded edge, which should be able to lift the battery without puncturing it. Upgrading the speaker at the same time could be a useful hack, if a better one can be found that fits. Although don't know if the impedance is the same for most phone speakers.
Will post results here including any lessons learnt. Cheers Ron.
The replacement usb charge board arrived, purchased from this guy: http://www.ebay.com/itm/New-Origina...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 Posting the url as the service was excellent. Very well packed in its own cardboard box and sent by registered post. So I would buy from him again, even if he is a little more expensive than some on AliExpress.
To fit the new board, the case was opened, as described above and the battery removed. To remove the battery, two screws need to be removed from a metal plate covering the battery connector. The battery ribbon cable connector can then be levered up with a small flat screwdriver blade. It's a effectively a plug with a push fit onto the connector so just pops off.
To remove the battery I used an old credit card, sliding it underneath at one edge of the battery, then gently pushing it forward to release the battery bit by bit, from it being glued to the base. This shouldn't need a lot of force and it is important to avoid snagging the ribbon cable that runs under the battery.
The black plastic cover that houses the speaker and covers the charging board was then removed by unscrewing 4 screws. On my phone one screw had a white plastic covering, into which a cross head jewellers screwdriver can be pushed to grip the screw. The charger board was then exposed and the two speaker wires and two wires from the vibrator were unsoldered using a fine tip iron. The plastic cover was then fully removed. The black rubber tape covering the ribbon cable connector was scraped away, the connector unlocked and the ribbon cable removed. The antenna connector attached to the charger board was then levered off using a small flat bladed screwdriver. The charger board itself was then pulled out. It is held in place by tiny plastic tabs on either side and was a bit of a fiddle to remove.
The old charger board has some Kapton or similar tape underneath, which the new board didn't have. So I applied some similar tape to the new board, but this may not be essential. The new board was then fitted back in, again a bit of a fiddle. I found the best way was was to insert the right hand side of the board first under its tab (looking at the inside of the phone from the charger end), with the board rotated slightly anti clockwise, then pushing the left hand side forward (rotating clockwise) and under the left hand tab so that it effectively clicks into place (not much of a click). The rest of assembly was the reverse of disassembly. Soldering the 4 wires (polarity is marked on the board), pushing the ribbon cable squarely into the connector and locking it. Nearly forgot to push the antenna connector back on!
Replaced the back and the new charge board worked perfectly. What a relief! Thanks again to Monster for getting me started. Cheers Ron.
Hello everyone,
I have every tool needed to fix any problems on any mobile phones. But after fixing my y6, I have thought that a T5S would be piece of cake. But it's not.
Any ideas if I can just remove the broken digitizer to attach the new one or is it glued to the LCD like all new Samsung models?
Hey guys, so my mi5's digitizer broke and I'm changing it. Anyway I got a problem: while trying to remove the battery both the adhesives broke even before I started pulling them out. Now I'm stuck with the battery glued to the device. I don't want to try to pull it out using tools since I had a bad experience in the past (almost made a hole in a battery), is there anyway I can do it without damaging it? (since it is also pretty new and I don't want to change it). Maybe heating it and using a suction cup could do?
Good Question, I had the same Problem with another phone. I also heated it up with a hair dryer and pulled and carefully out with a plastic pryer tool (no sharp tools here as you stated - had the experience with a galaxy S7 edge that I made a hole into.it and it swollen up immediately...very scary but luckily nothing more happens...)
Good Luck!!
Naily
One way is to heat up adhesive with hair dryer and gently work it out with some plastic tool
Hi, I have an almost 2 year old Moto G6 (just the G6, not Play or Plus). Had it in the same case that length of time. About a month ago, found it was hard to press the power button. I finally just took it out of the case, and in doing so, found the allegedly permanently sealed back cover was coming loose on the side with the power button as well as the bottom where the USB-C jack is. Looks like the adhesive is stretchy but no longer very tacky, and trying to manually press the back cover into place is futile as it won't stay and won't even go all the way in. The phone still works, and after removing it from the case, I now see the power button is fine. I assume it's out of warranty now, I think 1 year and I have no add-on protection plan on my T-Mobile bill. I seen videos of people removing the back cover with a heat gun and razor blade to replace the battery. On what I can see, doesn't look like my battery is bulging. Tempted to crazy glue where the cover is separating, but I doubt that would hold with the pressure that makes the cover pull out again once pushed down. I would think at this point I could carefully just manually remove the whole back cover by hand.My dexterity is awful on repairing small delicate things. Can a shop repair this fairly cheaply? Any advice? I'm in Ohio/USA. Thanks!
I took mine out of the case tonight to clean it and discovered I have exactly the same problem! My case is such that if I put the phone back in it, the case "snaps" together and hence keeps the phone together. Mine is probably two years old too, so I'm sure no fix is possible (but I'll keep my eye on this thread). I'll leave the case on and begin looking for a new phone.
I'm with Sprint so I'm anticipating the conversion to TMo, so I'd rather wait until that happens before I buy a new one.
dannykewl said:
Hi, I have an almost 2 year old Moto G6 (just the G6, not Play or Plus). Had it in the same case that length of time. About a month ago, found it was hard to press the power button. I finally just took it out of the case, and in doing so, found the allegedly permanently sealed back cover was coming loose on the side with the power button as well as the bottom where the USB-C jack is. Looks like the adhesive is stretchy but no longer very tacky, and trying to manually press the back cover into place is futile as it won't stay and won't even go all the way in. The phone still works, and after removing it from the case, I now see the power button is fine. I assume it's out of warranty now, I think 1 year and I have no add-on protection plan on my T-Mobile bill. I seen videos of people removing the back cover with a heat gun and razor blade to replace the battery. On what I can see, doesn't look like my battery is bulging. Tempted to crazy glue where the cover is separating, but I doubt that would hold with the pressure that makes the cover pull out again once pushed down. I would think at this point I could carefully just manually remove the whole back cover by hand.My dexterity is awful on repairing small delicate things. Can a shop repair this fairly cheaply? Any advice? I'm in Ohio/USA. Thanks!
Click to expand...
Click to collapse
You could try using a hair dryer to heat up the glue to make it stick together again.
You could try using a hair dryer to heat up the glue to make it stick together again.
Click to expand...
Click to collapse
I thought maybe excessive heat and sweat from being in my pocket on hot days loosened it up.
Thanks for the replies FrogFan and Ragarianok. Sorry for the long delay. In the meantime, I got the back case half off, and indeed a swollen battery. I am going to order a new battery for $4 from Mobile Defenders in MI, battery image says Motorola on it, and they say authorized OEM. A nearby repair shop said they will put it in for $20. They said a decent battery should run $20+, but all those higher priced ones on ebay and Amazon are no-names.
Thanks for coming back, dannykewl. I wasted some time inquiring about a fix from Motorola and found out that their "fix" would cost more than the phone was worth. A local shop quoted a ridiculously high price to fix it, too, but they did say the problem could be caused by a swollen battery. I will check with other local shops to see what they'd charge to replace the battery and seal it back up.
Did you get yours fixed?
POP!
My phone separated today and it is a swollen battery. I suspected for about 2 months the battery was swelling because of pressure points showing up on the screen as bright circles. I was just going to buy a new phone as this was a cheap phone and 2 years old, but the battery did the hard work for me by separating the phone from it's back, so I decided to fix. I removed the battery, ordered replacement battery on ebay and will put back together myself for $12. The $4 batteries are out of stock. The phone has enough stickiness left to hold the backplate and phone together on it's own, and it'll be in the phone case so no worries. Might apply a little Elmers to the surround. From what I read online, and saw on Youtube, be careful with the back, it's actually a glass metal hybrid and not safety glass at that. It will shatter off the metal and into little tiny razors and knives. The screen artifacts disappeared when the back was removed, relieving pressure on the components mashing up against the screen from the inside.. No permanent damage. This new battery should tide me over long enough for the affordable 5g phones to come out. I don't buy pricey phones. Oh, fyi... this is a SUPER easy repair. Have faith and go for it.
I took mine to a local repair shop today and confirmed my problem was also a swelling battery. They will replace the battery for me for $75.
Oh, fyi... this is a SUPER easy repair. Have faith and go for it.
Click to expand...
Click to collapse
I checked out a YouTube video on this topic and quickly confirmed that this repair is way over my head. I don't have the tools or the patience to change the battery in this phone.