The screen on my Rogers HTC Raider is scratched. It is deep enough that I cannot remove by applying polisher. Screen still works but I rather replace the screen as the scratch is visible.
Where can I purchase the screen and replace it myself?
http://www.tmart.com/Replacement-LCD-Display-Screen-for-HTC-G19-Raider-4G_p137438.html
http://www.repairsuniverse.com/htc-vivid-screen-replacements-repair-parts.html
..
Thank you.
tap the thanks button
and good luck
A little advice - I've already replaced the screen on my Raider
Hi, glad someone else is attempting this. I had never replaced a screen in a phone before trying this so for me it was a little hair raising the first time I took it apart. On the back of the phone under the battery cover are 5 screws you need to remove, and one little plastic cover. Under the cover is the connector from the mainboard. Its just a little pop out connection, gently lever it loose before removing the shell to avoid hurting the ribbon.
Once you get this far, flip the phone face-up, and *from the bottom*, gently lever the sides and bottom of the plastic shell away from the screen. Its relatively easy.
Continue working along the edges toward the top until the plastic shell pops free, after that put it face-down again and remove the screws holding the battery holder to the rest of the phone. Pull it up and out to the left to remove it, being careful not to bend the battery contacts as they stay with the rest of the phone. Keep the screws with it, trust me - its easier to remember what goes where this way.
Once you have the battery holder off, put it aside and remove the screws holding the mainboard(s) to the shell. Also you will find three wires with little cup contacts at the ends, gently detach these as well, and when the screws and wires are off, carefully remove the boards. Look closely at the plastic tabs holding them in and you'll see how they come out. When taking them out of the phone you'll need to lift them like you were opening a book - ie. folding them to the right. Underneath are two sockets with ribbon cable connections, one should already be detached - the other can be popped off at this point. If you skipped detaching it at the beginning, now's the time to remove both.
This should leave you with two free boards attached in the middle by a black ribbon. Put them aside and what you have left in your hand is the metal shell, LCD, and digitizer.
NOW..the crappy news. This wonderful, beautiful, powerful, ESPENSIVE phone, is held together by black double-sided tape. Yep. Tape. AND you'll need some more before installing the new digitizer. I ordered mine from tmart as well and it not only comes with the wrong screwdrivers (btw you need a #1 philips bit - VERY tiny!!) but it doesn't come with any adhesive to mount the screen to.
Your new screen should also come with some prying tools, and they are quite handy. The guitar pick one didn't do much but the lever is very handy. You'll need to gently pry the digitizer away from the LCD with this tool being careful not to put too much pressure on the lcd or it might snap. Its only a few mm thick. GO SLOW.. you should have no problems. I've done it a few times now - I'm kinda rough on my toys.
Once you have the part un-taped, its still got the ribbon cable going back behind the lcd. Its connected to a small, thin socket on ther board. You lift a small white lever (remove the tape and save it - reapply it to the new connection) and slide the cable out. You'll need to use your lever again and pry up the lcd enough to slide the ribbon out from behind it. This can be tricky. Again, go slow, be real cautious..the tape is pretty strong. Once you have the panel out completely its just a matter of reversing the process. If you're real careful when removing the original panel, you might be able to reuse the double-sided tape thats in there.. I wasn't so lucky. Mine was covered in glass shards, as I mashed my screen pretty good.
Hope this helps!! I had a rough time the first time, but now its easy for me. I like taking it apart lol..
Let me know how you do! Good luck!
Brian
Hi guys, here is the problem.
I recently bought a full housing for my X8, it shipped with this http://pic.hkyrd.com/uploadpic/SKU/CA/CA100/CA100 (6).jpg
My question now is, how can I replace only the digitizer to this new front cover housing, I looked at this http://erkinson.altervista.org/en/sony-ericsson-xperia-x8-smontaggio-e-sostituzione-display-touch/ but there is the front cover with digitizer on it already and I have to replace only http://www.duocai.co.uk/media/catal...78eab33525d08d6e5fb8d27136e95/l/e/lensex8.jpg
Can someone give me a good and thorough answer, I'm not making any fun of it because digitizers are expensive. Is digitizer sticked on the back of the screen or what? How can I securely replace it? Thanks.
I think the digitizer is glued to the front cover and it's hard to separate. You will have to apply alot of force.
Be careful because the whole digitizer is made of glass and it can break easily (if it's not glass then it's a type of hard plastic that can break too).
I'm not sure of this, i opened my phone once but didn't notice how it is holded. Open it yourself and take a look.
Sent from the bathroom using the toilet
Put the old front with old digitizer in a cooker, not too hot, then push old digitizer out and use the hot glue to help stick your new one, if you end up having to use glue, be careful as it can run onto the screen
Sent from my E15i using xda premium
Thanks for info.
@Llor - I heard the option with hot air also, they sayed it's more safe..Also, if I put it into kitchen or hot air, can the chips or the flat cable or something like that melt?
lsalamun said:
Thanks for info.
@Llor - I heard the option with hot air also, they sayed it's more safe..Also, if I put it into kitchen or hot air, can the chips or the flat cable or something like that melt?
Click to expand...
Click to collapse
The chips and the cable are prepared for high temperatures since they were soldered together (but in a short period of time), i don't know about the rest toh..
The heat gun is better because you can have better control with the heat but they can also reach very high temperatures (enough to melt the solder and burn everything xD). You must use it from a good distance..
A good hair dryer that can make heat can also be an option. They make enough heat to burn you but not enough to melt anything..
150° Celcius is enough to melt the solder but by that time the whole front cover will be almost liquid
It's risky, be careful..
Edit:
Disclaimer: i'm not responsible bla bla bla yada yada yada
Sent from the bathroom using the toilet
Been lurking in this forum for months and I read a topic about the battery being able to be removed. So I tried it myself because my phone is fine but battery life capacity is getting worse with so much recharging. Got a new battery and I swapped it out so that works!
But now once in a while my phone likes to shut off for no reason as if I'm doing a battery pull. Why is that and what can I do about it? I know that I took off the sticky adhesive so the phone is not totally secure, is it okay to put tape on it to secure it? And since the phone must be held by T5 torx screws, does it have to be totally screwed in (the screw I use is cheap and might be worn out so it doesn't tighten completely)?
techhexium said:
And since the phone must be held by T5 torx screws, does it have to be totally screwed in (the screw I use is cheap and might be worn out so it doesn't tighten completely)?
Click to expand...
Click to collapse
The two screws at the base of the battery are terminals from what I can tell so if one of them is not fitting tight then that might be your problem.
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Droidriven said:
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Click to expand...
Click to collapse
Already search extensively, no luck so far. Prefer not to 'experiment' and wreck the thing!
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Bro check YouTube very well... it there
Sent from my iPhone using Tapatalk Pro
I can help you.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Did u fix it? I can help you. I opened the phone like 10+ times.
Hi, I have the same problem, I need to open the phone to replace the camera but did not manage to find anything on youtube. Would u please help me? Thanks
Monster 00 said:
Did u fix it? I can help you. I opened the phone like 10+ times.
Click to expand...
Click to collapse
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
kiwironnie said:
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
Click to expand...
Click to collapse
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Monster 00 said:
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Click to expand...
Click to collapse
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
kiwironnie said:
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
Click to expand...
Click to collapse
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Monster 00 said:
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Click to expand...
Click to collapse
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
kiwironnie said:
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
Click to expand...
Click to collapse
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Monster 00 said:
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Click to expand...
Click to collapse
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
kiwironnie said:
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
Click to expand...
Click to collapse
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Monster 00 said:
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Click to expand...
Click to collapse
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
kiwironnie said:
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
Click to expand...
Click to collapse
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Monster 00 said:
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Click to expand...
Click to collapse
Brilliant, thanks again! No need for a video, as your explanation is very clear and should be obvious to others after they get the back off the phone. Having recently removed a glued battery from a Kindle, it was a hell of an arm wrestle! Hopefully it will be a bit easier with the Y6. I have a flat nylon spudger with a rounded edge, which should be able to lift the battery without puncturing it. Upgrading the speaker at the same time could be a useful hack, if a better one can be found that fits. Although don't know if the impedance is the same for most phone speakers.
Will post results here including any lessons learnt. Cheers Ron.
The replacement usb charge board arrived, purchased from this guy: http://www.ebay.com/itm/New-Origina...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 Posting the url as the service was excellent. Very well packed in its own cardboard box and sent by registered post. So I would buy from him again, even if he is a little more expensive than some on AliExpress.
To fit the new board, the case was opened, as described above and the battery removed. To remove the battery, two screws need to be removed from a metal plate covering the battery connector. The battery ribbon cable connector can then be levered up with a small flat screwdriver blade. It's a effectively a plug with a push fit onto the connector so just pops off.
To remove the battery I used an old credit card, sliding it underneath at one edge of the battery, then gently pushing it forward to release the battery bit by bit, from it being glued to the base. This shouldn't need a lot of force and it is important to avoid snagging the ribbon cable that runs under the battery.
The black plastic cover that houses the speaker and covers the charging board was then removed by unscrewing 4 screws. On my phone one screw had a white plastic covering, into which a cross head jewellers screwdriver can be pushed to grip the screw. The charger board was then exposed and the two speaker wires and two wires from the vibrator were unsoldered using a fine tip iron. The plastic cover was then fully removed. The black rubber tape covering the ribbon cable connector was scraped away, the connector unlocked and the ribbon cable removed. The antenna connector attached to the charger board was then levered off using a small flat bladed screwdriver. The charger board itself was then pulled out. It is held in place by tiny plastic tabs on either side and was a bit of a fiddle to remove.
The old charger board has some Kapton or similar tape underneath, which the new board didn't have. So I applied some similar tape to the new board, but this may not be essential. The new board was then fitted back in, again a bit of a fiddle. I found the best way was was to insert the right hand side of the board first under its tab (looking at the inside of the phone from the charger end), with the board rotated slightly anti clockwise, then pushing the left hand side forward (rotating clockwise) and under the left hand tab so that it effectively clicks into place (not much of a click). The rest of assembly was the reverse of disassembly. Soldering the 4 wires (polarity is marked on the board), pushing the ribbon cable squarely into the connector and locking it. Nearly forgot to push the antenna connector back on!
Replaced the back and the new charge board worked perfectly. What a relief! Thanks again to Monster for getting me started. Cheers Ron.
Hello everyone,
I have every tool needed to fix any problems on any mobile phones. But after fixing my y6, I have thought that a T5S would be piece of cake. But it's not.
Any ideas if I can just remove the broken digitizer to attach the new one or is it glued to the LCD like all new Samsung models?
Hi guys,
has anyone of you tried changing the front glass without digitizer and display?
In disassembly videos I can only see people changing the whole thing.
Also, do you think I can manage to repair the front glas as well as the USB port with just an iron instead of a hot air blower (and the usual tools made of plastic)?
Thanks in advance!
kadofl said:
Hi guys,
has anyone of you tried changing the front glass without digitizer and display?
In disassembly videos I can only see people changing the whole thing.
Also, do you think I can manage to repair the front glas as well as the USB port with just an iron instead of a hot air blower (and the usual tools made of plastic)?
Thanks in advance!
Click to expand...
Click to collapse
I haven't done the front glass on mine yet, but my understanding is that in general you're really better off replacing front glass as an entire unit with digitizer and display. An iron on pretty low through a cloth/towel might well work. It's not just glue that melts, it's a thin strip of rubber gasket material with adhesive (okay, maybe it's thick glue, but it looked pre-formed to me) holding the glass back cover on.
Heating probably helps a bit with softening the stuff, but after the first time you peel it up you won't really need to do that again. I'd recommend picking a corner (say, bottom left as you're looking at the back) and just plan on prying from there every time, so you only have one spot where the plastic gets marred.
Don't spend too much time heating, worry more about having a suction cup tool that you can lift with while you try to work a guitar pick or hobby knife or something in under the corner. Have at least two ready, so you can wedge one in, and work your way around without it just dropping back down on you. You'll probably tear the material a bit but that's okay, just spread it back out evenly around the edge on the glass before you put the cover back on. Also, you definitely should be using a case to make sure it doesn't just fall off in your pocket once you've opened it up a couple times.
USB cable replacement isn't awful, just time consuming. The biggest gotcha is to keep all three of the little gold clips on the plastic "mid frame" ring (that's the first thing you remove that requires screws after getting the back glass up) from fallling and getting lost.
You can PM me if you have any questions about this, I've replaced my USB cable/port assembly a couple times (first replacement was defective). And I'm about to attempt replacing the screen as a whole unit with glass & digitizer on my wife's Z2 Plus, so I'll let you know how that goes.