Related
Hey fellas,
I followed all the steps in http://forum.xda-developers.com/showthread.php?t=1030227 that link up until step 8, where my Nook would not recognize the SD card as a boot disk. My laptop does, however, which means the burning of cwm3.2.0.1 worked fine. The Nook just starts up as it normally would without automatically booting into recovery. The SD card is recognized as a standard SD card in the Nook, and all the files are seen (but can't be opened because they're not recognized...I'm not sure if I missed something or what, but I can't figure it out. It's running stock 1.2 and the SD card is a class 10 Samsung 32G, which works just fine. Any advice?
monkor said:
... Any advice?
Click to expand...
Click to collapse
Get a Sandisk class 4 card.
MISRy said:
Get a Sandisk class 4 card.
Click to expand...
Click to collapse
Is that actually why it's not going to boot? I think I have a 2GB class 4 in my phone...
Sandisk. It's important that it be a Sandisk class 4.
Somehow your card is not burned properly. It could be your card like misry said. But it could also be the steps you took. Pay attention to what eyeballer said in his first post. 'Run as administrator' and use external usb readers instead of built in readers.
The Nook is very finicky about how a card is formatted before it will boot from it. Your PC can read it, but the Nook will not boot from it. If the image from eyeballer is burned properly, it will boot.
Now that he mentions it I think leapinlar has a better handle on this one.
Alright I'll give it a try and Jerry you guys know! Thanks!
Sent from my HTC Sensation Z710e using XDA
MISRy said:
Get a Sandisk class 4 card.
Click to expand...
Click to collapse
i actually have the same problem...
i have a sandisk 32gb class 10-doesnt boot from that
i have a sandisk 16gb class 4-doesnt boot from that
i know my nook can boot from sd because i have been dual booting for a couple days now until i could find the correct tutorial for my nook (no green or blue sticker, 1.4.2, 8gb model)
what do you think i should do?
edit:when i do the dual boot, it works with either card
Edo526 said:
i actually have the same problem...
i have a sandisk 32gb class 10-doesnt boot from that
i have a sandisk 16gb class 4-doesnt boot from that
i know my nook can boot from sd because i have been dual booting for a couple days now until i could find the correct tutorial for my nook (no green or blue sticker, 1.4.2, 8gb model)
what do you think i should do?
edit:when i do the dual boot, it works with either card
Click to expand...
Click to collapse
What are you booting? The trick is to get the card formatted so it will boot in the first place.
Also if your dual boot sd is a cm, boot to that and go to ROM Manager and flash CWM to emmc using the first menu choice. Then you have CWM on internal memory you can use for flashing, backing up, etc.
Edit: I just added a section to my tips thread linked in my signature to help users understand about bootable SDs.
leapinlar said:
What are you booting? The trick is to get the card formatted so it will boot in the first place. Once you have done that, you can put the card in the PC and put any files you want there. Back up by renaming to .bak all the existing files on the boot partition of the working sd and put eyeballers cwm files there (all of them, including mlo, uImage, uRamdisk, etc.) See if that boots into cwm. If not, just remove eyeballers files and restore the original files.
Also if your dual boot sd is a cm, boot to that and go to ROM Manager and flash CWM to emmc. Then you have CWM on internal memory you can use for rooting, etc.
Edit: I just added a section to my tips thread linked in my signature to help users understand about bootable SDs.
Click to expand...
Click to collapse
i run Team-B-CM7SD-Alpha_final on my dual boot, but when i put the emmc .zip into my sd and booted i couldnt find it in the rom manager, only shows folders
Edo526 said:
i run Team-B-CM7SD-Alpha_final on my dual boot, but when i put the emmc .zip into my sd and booted i couldnt find it in the rom manager, only shows folders
Click to expand...
Click to collapse
First you are running on a Nook Tablet, not a Nook Color. You will never get eyeballers CWM card to run on that. That is for Nook Color. Second, that is not how you flash CWM with ROM Manager. You use the first two menu choices. But you will find no CWM for the Nook Tablet listed there. I suggest you start reading the Nook Tablet forums, this is Nook Color.
I think my not being able to boot is an issue with the Nook. On my first Nook that I got around Christmas, the root worked just fine. But the one I was recently asked to root, with the same card (32GB class 10), no success. I'm trying to find a backdoor into recovery so I can circumvent this issue. there has to be a way to manually boot into stock recovery and work from there
Sent from my HTC Sensation Z710e using XDA
leapinlar said:
First you are running on a Nook Tablet, not a Nook Color. You will never get eyeballers CWM card to run on that. That is for Nook Color. Second, that is not how you flash CWM with ROM Manager. You use the first two menu choices. But you will find no CWM for the Nook Tablet listed there. I suggest you start reading the Nook Tablet forums, this is Nook Color.
Click to expand...
Click to collapse
Wow thanks man, ill check out the tablet forums on here, you've been a great deal of help
monkor said:
I think my not being able to boot is an issue with the Nook. On my first Nook that I got around Christmas, the root worked just fine. But the one I was recently asked to root, with the same card (32GB class 10), no success. I'm trying to find a backdoor into recovery so I can circumvent this issue. there has to be a way to manually boot into stock recovery and work from there
Sent from my HTC Sensation Z710e using XDA
Click to expand...
Click to collapse
You say you got the card to boot to the CWM card on your other nook. Will it still boot it? If you have prepared the card fresh, see if you can boot it with either nook. And you are sure this second nook is a Nook Color, not a Nook Tablet like the other user above? They look very much alike.
Edit: You say root, do you mean you want to root the stock on emmc or do you mean flash CM on emmc?
Edit 2: If you are using winimage to burn, be sure to select "Restore Virtual Hard Disk Image on Physical Drive" rather than "write disk".
Sent from my Nook Color running ICS and Tapatalk
So I'm trying to follow everything from here http://forum.xda-developers.com/showthread.php?p=38153094#post38153094 and I got lost at the part where I have to burn the image. When I burn it basically repartitioned my 8gig sd card down to 120mbs... What am I doing wrong? I don't know if I need to burn cwm first or if it's included there?
jmstrat said:
So I'm trying to follow everything from here http://forum.xda-developers.com/showthread.php?p=38153094#post38153094 and I got lost at the part where I have to burn the image. When I burn it basically repartitioned my 8gig sd card down to 120mbs... What am I doing wrong? I don't know if I need to burn cwm first or if it's included there?
Click to expand...
Click to collapse
That is what it is supposed to do, be 120 MB. And that 120Mb includes the CWM so you can flash the CM ROM. When you boot it in the nook, it further partitions it so that CM can be installed on the SD. Don't worry, the rest of your 8GB will be available.
Sent from my Nook HD+ running CM10 on Hybrid SD
Thanks!
leapinlar said:
That is what it is supposed to do, be 120 MB. And that 120Mb includes the CWM so you can flash the CM ROM. When you boot it in the nook, it further partitions it so that CM can be installed on the SD. Don't worry, the rest of your 8GB will be available.
Sent from my Nook HD+ running CM10 on Hybrid SD
Click to expand...
Click to collapse
Ok, the problem I had was that I was confused regarding where to put the rest of the files, apperantly I'm and idiot and didn't realize I'm supposed to put them in the internal memory... Ok let's see how it goes, thanks!
jmstrat said:
Thanks but how am I supposed to copy the cm10 zip file and gapps/converter file if they wont fit onto it? Also do I just insert the sd card in and then it automatically reformats it and then I'm supposed to plug it back into my pc drag the cm10 files and then put it back into the nook again? Forgive my ignorance I really want to try this out though! I also forgot to mention that I haven't done anything with my nook, it's non rooted and then only thing I've done is sideloaded the playstore on there, that's it. My nook is completely stock.
Click to expand...
Click to collapse
I'm not sure you read my instructions. I said to put the CM zip, gapps zip and converter zip on the internal media SD built into the nook, not on the external SD inserted into your PC. So it does not matter if the SD is only 120 MB, you are copying nothing there. Just download the zips with stock to internal SD or hook your cable to the PC with stock booted and copy to internal SD.
EDIT: I just edited the OP to clarify all this.
Sent from my Nook HD running CM10.1 on Hybrid SD
You weren't supposed to see that message lol..
leapinlar said:
I'm not sure you read my instructions. I said to put the CM zip, gapps zip and converter zip on the internal media SD built into the nook, not on the external SD inserted into your PC. So it does not matter if the SD is only 120 MB, you are copying nothing there. Just download the zips with stock to internal SD or hook your cable to the PC with stock booted and copy to internal SD.
Sent from my Nook HD running CM10.1 on Hybrid SD
Click to expand...
Click to collapse
Oh no I figured it out!!! I thought I deleted that comment I didnt want to embarrass myself.. I have another question, I'm using an 8gig card, but I want to get a 64gib card, what should I do when I get the new card, reburn and do the same steps? Thank you for replying to my question so quickly you're ****ing awesome! Wow I'm just messing around with cm10, it's like a new tablet, holy ****. Sketchbook pro appears to have less latency, finally I can draw! So what else is possible with cm10 now, what do you like about cm10 that wasn't possible before? Also what build prop is the tablet being seen as now?
jmstrat said:
I have another question, I'm using an 8gig card, but I want to get a 64gib card, what should I do when I get the new card, reburn and do the same steps?
Also what build prop is the tablet being seen as now?
Click to expand...
Click to collapse
If you want to move to a larger card, use win32diskimager to read the 8GB card to a file. The file will be 8GB. Then use win32diskimager to write that file to your new 64GB card. Then use partitioning software like Mini-Tool Partition Wizard to expand the last partition to the full size of the card.
The build prop is set as a B&N Nook HD.
Sent from my Nook HD+ running CM10 on Hybrid SD
So, a few days ago verygreen uploaded his emmc cyanogenmod install for Nook HD+. I was ecstatic but only got around to installing it today. Install went great up until after flashing the rom.The nook threw an error when trying to unmount the sd card (as per verygreen's instructions) "no problem, I'll just shut down the tablet" I thought. So I do so, remove the SD card, turn the tablet back on, and insert a seperate SD card for storage. The rom loaded up just fine and everything seemed normal. I downloaded and ran a benchmark to see that everything was up to par then went to take a screenshot (to compare to other versions later). A second later I looked at my notifications bar to see a message that the screenshot could not be taken because there is no SD card. After a short investigation I realized that the SD card wasn't showing up in my storage section. It showed up just fine in my computer and I've used the card in this nook before. Just to be sure I plugged the CWM card from earlier, sure enough it didn't show up either. As I'm not a complete novice I figured I should try reflashing before coming here. I did so and the nook seemed to recognize that the card was there! Wait, it now says the card is blank or in an unsupported filesystem. Checking the SD on the computer shows it to be in Fat32, which worked in all previous Roms just fine and clicking the notification to try and format also does nothing. Anyone have any advice?
Additionally I should probably mention that I am using the 05/05 Rom, which I thought was supposed to fix mounting issues
Same issue here :/
tehkingo said:
Same issue here :/
Click to expand...
Click to collapse
Yours was on Hybrid and easily solved. His is on emmc.
Sent from my Nook HD+ running CM10.1 on emmc.
---------- Post added at 05:42 PM ---------- Previous post was at 05:36 PM ----------
Nookuser19 said:
So, a few days ago verygreen uploaded his emmc cyanogenmod install for Nook HD+. I was ecstatic but only got around to installing it today. Install went great up until after flashing the rom.The nook threw an error when trying to unmount the sd card (as per verygreen's instructions) "no problem, I'll just shut down the tablet" I thought. So I do so, remove the SD card, turn the tablet back on, and insert a seperate SD card for storage. The rom loaded up just fine and everything seemed normal. I downloaded and ran a benchmark to see that everything was up to par then went to take a screenshot (to compare to other versions later). A second later I looked at my notifications bar to see a message that the screenshot could not be taken because there is no SD card. After a short investigation I realized that the SD card wasn't showing up in my storage section. It showed up just fine in my computer and I've used the card in this nook before. Just to be sure I plugged the CWM card from earlier, sure enough it didn't show up either. As I'm not a complete novice I figured I should try reflashing before coming here. I did so and the nook seemed to recognize that the card was there! Wait, it now says the card is blank or in an unsupported filesystem. Checking the SD on the computer shows it to be in Fat32, which worked in all previous Roms just fine and clicking the notification to try and format also does nothing. Anyone have any advice?
Additionally I should probably mention that I am using the 05/05 Rom, which I thought was supposed to fix mounting issues
Click to expand...
Click to collapse
You make it sound like you are trying to insert the SD after you have booted to CM10.1. That won't work. You must boot with the SD already inserted so that it is recognized while CM10.1 starts up.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
Yours was on Hybrid and easily solved. His is on emmc.
Sent from my Nook HD+ running CM10.1 on emmc.
---------- Post added at 05:42 PM ---------- Previous post was at 05:36 PM ----------
You make it sound like you are trying to insert the SD after you have booted to CM10.1. That won't work. You must boot with the SD already inserted so that it is recognized while CM10.1 starts up.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
That didn't work I'm afraid. The message about the blank SD card is gone but it still won't let me save a screenshot. Gives a message about the storage being in use. Also, attempting to move an app to the SD card says there's not enough space... On my freshly formatted 32 gigabyte card that, once again, works and reads just fine on my computer. I will mention there is a header for the SD under my storage tab in settings, and it attempts to calculate the used space of the SD, however it does that whether the card is in or not. For that reason I don't think it means anything. Any other ideas? Because I'm certainly at a loss.
Nookuser19 said:
That didn't work I'm afraid. The message about the blank SD card is gone but it still won't let me save a screenshot. Gives a message about the storage being in use. Also, attempting to move an app to the SD card says there's not enough space... On my freshly formatted 32 gigabyte card that, once again, works and reads just fine on my computer. I will mention there is a header for the SD under my storage tab in settings, and it attempts to calculate the used space of the SD, however it does that whether the card is in or not. For that reason I don't think it means anything. Any other ideas? Because I'm certainly at a loss.
Click to expand...
Click to collapse
How did you freshly format the card? With Windows? You need to use a program named SDFormatter free on the web.
If you boot with no card in you will see that it does not show a card under storage, does not attempt to calculate, etc. There is something about your card it does not like. The hardware on the HD+ is notoriously faulty when it comes to SDs. Format it with SDFormatter, clean the contacts, make sure it is seated well in the slot and anything else you can do to improve things.
Sent from my Nook HD+ running CM10.1 on emmc.
Update
I'm a moron. I failed to notice that the rom that the I downloaded actually was the 05/04 rom, the one with no bluetooth or SD mounting... In my defense verygreen hadn't updated his post (I downloaded from the one he linked in the body of his text, not at the bottom). *Sigh* Still though, I should have been paying more attention and if I had been less lucky I could have bricked my device. Anyways, after flashing the PROPER rom SD mounting works fine (though it was a bit finicky, requiring a reboot before finally working). Anyways thanks for your time, and sorry for giving inaccurate information.
what is the sd format allowed by hd+ in emmc?
I wanted to follow up on this thread by asking a general concluding question-
In order to use the sd cards directly in emmc, will the SD cards have to be in fat32 format only? Or can it be in exfat (or even ntfs)? According to a thread, somebody put a quote from the nook website that it can handle exfat.
The reason is that I wanted my nook to be able to read mkvs. I went through the sdformatter software, and it seems that it only formats in fat32.
TIA.
leapinlar said:
How did you freshly format the card? With Windows? You need to use a program named SDFormatter free on the web.
If you boot with no card in you will see that it does not show a card under storage, does not attempt to calculate, etc. There is something about your card it does not like. The hardware on the HD+ is notoriously faulty when it comes to SDs. Format it with SDFormatter, clean the contacts, make sure it is seated well in the slot and anything else you can do to improve things.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
I am having same problems.Inastalled Verygreen's CM10.1 on internal storage this morning.SD card is not being recognized by nook.I go to settings and tap "storage" and settings force closes,Tried to mount sd card thru recoveryand error message comes up.I formatted sd card in windows and then SD Formatter in fat32 format,C
leaned sd slot with compressd air,No go.Tried 3 different cards Samsung.sandisk class 10 32 gb,sandisk class 4 16gb ,Samsung class10 8gb same result.E
nen reinstalled CM 10.1 emc 6/8/13.did not help.
akramarshad said:
I am having same problems.Inastalled Verygreen's CM10.1 on internal storage this morning.SD card is not being recognized by nook.I go to settings and tap "storage" and settings force closes,Tried to mount sd card thru recoveryand error message comes up.I formatted sd card in windows and then SD Formatter in fat32 format,C
leaned sd slot with compressd air,No go.Tried 3 different cards Samsung.sandisk class 10 32 gb,sandisk class 4 16gb ,Samsung class10 8gb same result.E
nen reinstalled CM 10.1 emc 6/8/13.did not help.
Click to expand...
Click to collapse
I temporarily had the same issue, but mine was caused by me tampering with /system/etc/vold.fstab to test a new swap I was trying to make. I changed a setting there and it would not recognize the SD and settings/storage crashed. So that tells me that your system is definitely not mounting the SD. It could be a faulty SD slot. Are you sure you are completely clicking the SD into the slot? Did the slot work well when running stock?
Edit: How does it act when you boot with no SD inserted? Does settings crash? And what happens if you insert the SD after it is booted to CM10.1? Does settings crash then?
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
I temporarily had the same issue, but mine was caused by me tampering with /system/etc/vold.fstab to test a new swap I was trying to make. I changed a setting there and it would not recognize the SD and settings/storage crashed. So that tells me that your system is definitely not mounting the SD. It could be a faulty SD slot. Are you sure you are completely clicking the SD into the slot? Did the slot work well when running stock?
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
It was working fine with stock as well as hybrids from Verygreen as well as Bokbokan.I will try doing a complete wipe including system.Previusly I wiped data and catch partitions.
akramarshad said:
It was working fine with stock as well as hybrids from Verygreen as well as Bokbokan.I will try doing a complete wipe including system.Previusly I wiped data and catch partitions.
Click to expand...
Click to collapse
See the edit above.
Sent from my Nook HD+ running CM10.1 on emmc.
SD card not reading Nook HD+
Reinstlled after wipingdata,catch and system and now it is working fine.I guess something in system was causing it,Thanks Leapinlar I appreciate you prompt help.
same here with samsung galaxy exhibit 4g
akramarshad said:
It was working fine with stock as well as hybrids from Verygreen as well as Bokbokan.I will try doing a complete wipe including system.Previusly I wiped data and catch partitions.
Click to expand...
Click to collapse
I have tried all of the things listed on here. My sd card is formatted fat32. it reads just fine on my computer but when inserted into my phone I can't move apps to it, I can't open it to look at my files. I even tried removing everything from the sd and starting over. This has only been since I upgraded to cyanogenmod 10.1. any suggestions? I really want to move some stuff and am in need of my music files at the gym
jmcpheeters said:
I have tried all of the things listed on here. My sd card is formatted fat32. it reads just fine on my computer but when inserted into my phone I can't move apps to it, I can't open it to look at my files. I even tried removing everything from the sd and starting over. This has only been since I upgraded to cyanogenmod 10.1. any suggestions? I really want to move some stuff and am in need of my music files at the gym
Click to expand...
Click to collapse
You cannot move apps to SD with CM10.1. Apps2SD is not implemented.
And to access your external SD, you need to look in ext_sdcard. But CM10.1 on emmc uses the internal SD by default for everything. You can change that by flashing my swap SD zip from my HD/HD+ CWM thread linked in my signature. See item 4.
Sent from my Nook HD+ running CM10.1 on emmc.
to clarify
ok thanks. so just to clarify, does the nook hd/hd+ work for my Samsung exhibit 4g?
leapinlar said:
You cannot move apps to SD with CM10.1. Apps2SD is not implemented.
And to access your external SD, you need to look in ext_sdcard. But CM10.1 on emmc uses the internal SD by default for everything. You can change that by flashing my swap SD zip from my HD/HD+ CWM thread linked in my signature. See item 4.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
nook HD/HD+
it isn't showing up when I go to unzip on my phone.
This has proven to mean this isn't compatible with my phone. is there another version you can suggest for me to try?
jmcpheeters said:
ok thanks. so just to clarify, does the nook hd/hd+ work for my Samsung exhibit 4g?
Click to expand...
Click to collapse
jmcpheeters said:
it isn't showing up when I go to unzip on my phone.
This has proven to mean this isn't compatible with my phone. is there another version you can suggest for me to try?
Click to expand...
Click to collapse
It is a Nook HD+ rom, and will not work on a non-Nook HD+ device. Try the roms in the Galaxy Exhibit development forum.
If This Helps Anyone...
I spent roughly 4 to 5 days' worth of working hours sitting here at my laptop, trying more and more frustratingly, to get my Nook HD+ to take the new CM Rom, and then dealt with about a dozen full 1080p HD movies I had already spent about 3 hours each to convert to .mp4 and the right size for my Nook, which now was not showing ANY of the content on my 32g SD card. Well, I tried all the formatting (using the SDformatter program), all the re-booting and putting the content directly on it through the Nook, and putting the files on it through my laptop, and I got nothing.
Finally, after noticing a theme among most of the users who were having problems specifically with SanDisk and/or 32gb sized cards, I took the awesome (and expensive) 64gb class 10 SDXC Samsung card out of my Note 2 phone, and formatted that one using the SDF program, and put it on 'exFAT', and after putting the blank card back in my Nook (powering it off fully first), I had to COPY THE FOLDER FROM THE NOOK'S MAIN STORAGE CALLED "MY FILES" AND PASTE IT INTO THE SD CARD STORAGE. Then, I opened it and made folders inside that one for Movies, Music, eBooks, etc... I then loaded the movies onto it via the Nook itself, making sure to paste the files into the SD folder. I also noticed that I needed to keep the Nook from falling asleep, and set it to the highest setting of time before it would go into sleep mode (30 min) and had to keep swiping the screen to reset that time. I also just loaded one large movie file or a few smaller video files at a time, because if the screen went off, or if I had videos loading onto the Nook for more than a couple minutes, then I would get the frequently reported error saying that it 'could not copy'.
After doing all of this, I was finally able to start a couple of my movies with minor problems. I hate how it says in the video player I was using, that you have to use the right side touchscreen to swipe on an invisible volume control up or down, and it was extremely sensitive but also not easy to control.
So, to review:
-Try using a different card other than SanDisk and 32gb
-DL the free SDformatter program and use that to format ANY card you put in your CM rooted Nook! Try to set it at 'exFAT' also.
-Power OFF the Nook before installing the new SD card.
-Then plug the Nook into your computer, and COPY-PASTE the file folder "My Files" in the Nook's MAIN STORAGE and put it into the SD card. Make folders inside this one to sort your movies, music, books, etc.
-Copy-Paste your files that are NOT eBooks from your computer into the new 'My Files' on the SD card. (I suggest using Calibre or another program to load eBooks into your Nook after you have gotten all the metadata correct for each book.) Keep the Nook 'awake' and do not allow the screen to enter sleep mode during loading of files. Make sure to load only about 3 minutes' worth, or no more than one LARGE movie file at a time onto the Nook, to prevent it from disconnecting and giving you an error pop-up.
That should do it, and if you have problems after this, then maybe ask around more. I only know how this works by my own extensive (and exhausting) trial and error...
I was installing CM from verygreen thread "http://forum.xda-developers.com/showthread.php?t=2032364" Nook HD+ CM10 development (sdcard) updated 5/11.
I am using a san disk 32gb sd, i followed the steps unzip cwm image and write it to your sdcard using Win32 Disk Imager as he linked. Did that and booted into the nook hd, mounted it no problems. I haven't used ADB so i turned off the nook as it says to do and went to put the cm-10-20130511-UNOFFICIAL-ovation-sdcard.zip on the sd card. One problem the sd card now shows 116mb only of the 32gb and with no option to reformat it to make it larger. I tried formating from CWM didn't do anything. Pleas help i read the forums link for about 30mins with no answer to solve this problem. Just seen pushing ADB which i'm not familiar with. Thanks for any help suggestions.
I have an install guide for that ROM. Look at my HD+ easy install guide linked in my signature. I have a new image file there to help you.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
I have an install guide for that ROM. Look at my HD+ easy install guide linked in my signature. I have a new image file there to help you.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
Thank you! One problem so far, i went and installed the cm10 and gapps on the internal sd. i rewrote the sd card with your 6028cwm.
Once i insert he SD it says on the bottom CWM v6.0.2.7 and it wouldn't mount the emmc to install Cm10. I rewrote the sd card again and it said it took and still same thing.
Also tried your newer ramdisk but i can not rename my old ramdisk.cwm once its in my computer.
EDIT: I was using the Micro to full size SD adapter and that was locking it. I took the Micro and put it right into a micro sd card reader and BAM! Installing now.
Ran into this problem where it just locks up on booting, I take the SD card out stock nook works great. Loads to 99% then nothing, just hangs. I let it sit for an hour even.
gamer4067 said:
Ran into this problem where it just locks up on booting, I take the SD card out stock nook works great. Loads to 99% then nothing, just hangs. I let it sit for an hour even.
Click to expand...
Click to collapse
You are confusing me. This thread I'd for HD+. Yet you say the CWM said v6.0.2.7, which is for the HD. You should not be following my old guide if you are using verygreen's new SD scheme.... Oh I see your other comment was an old one....
The reason it stopped at 99% is the old SD version has too many partitions to allow stock to boot. It hands at 99%. To fix the problem, remove the SD before booting to stock.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
You are confusing me. This thread I'd for HD+. Yet you say the CWM said v6.0.2.7, which is for the HD. You should not be following my old guide if you are using verygreen's new SD scheme.... Oh I see your other comment was an old one....
The reason it stopped at 99% is the old SD version has too many partitions to allow stock to boot. It hands at 99%. To fix the problem, remove the SD before booting to stock.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
With no SD card in it works great on stock nook. The problem i'm running into is it wont boot to CM with the SD in. I get the cynogen start screen then a laggy cynogen loading then it goes to the stock nook with the 99%.
So the problem i am having is i cannot boot to CM with the SD card in. Without the card it works fine.
With the card in its boots to CM screen and the circle loads choppy and then it swaps to the nook 99%.
I just want the CM to boot. Any help will be greatly appreciate it. I can boot to CWR and i did mount the SD card and still same problem.
gamer4067 said:
So the problem i am having is i cannot boot to CM with the SD card in. Without the card it works fine.
With the card in its boots to CM screen and the circle loads choppy and then it swaps to the nook 99%.
I just want the CM to boot. Any help will be greatly appreciate it. I can boot to CWR and i did mount the SD card and still same problem.
Click to expand...
Click to collapse
You need to abandon that SD setup and start fresh with verygreen's new SD scheme. The old setup had some bugs. His new setup work much better. So go to his HD+ sdcard CM10.1 thread and start over with his early 7.1 cwm image. Then install his latest ROM and gapps and you will be very happy.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
You need to abandon that SD setup and start fresh with verygreen's new SD scheme. The old setup had some bugs. His new setup work much better. So go to his HD+ sdcard CM10.1 thread and start over with his early 7.1 cwm image. Then install his latest ROM and gapps and you will be very happy.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
Thank you!
I have Leapinlar's SD card image installed on a SD card that I used to then install the EMMC version onto my HD+ which is working great, thanks to Leapinlar and Verygreen for that. Since I don't want to misplace the SD card I've left it in my Nook, but then whenever I reboot it, it boots off of the SD card and goes into the CWM on the card. I was wondering if anyone knew of a way to activate the Cyanoboot menu on the card so that I could choose to boot from the card, or the EMMC, and possibly change the default so that it boots to the EMMC instead. I realize that this might not be the right forum as it isn't necessarily a Nook question, so thanks for any help.
Edit: I should specify that I used the 4GB CWM SD card image in Leapinlar's thread, and is the one I'd like to modify. Thanks.
Ask and Ye shall receive.
Attached below is a .rar file that has four files in it. Extract those files to the boot partition of your CWM SD, replacing any duplicates. It will add the cyanoboot menu to it. It will by default boot to CWM, but if you want to boot to emmc (stock or CM10.1 on emmc), hold the n key and the cyanoboot menu will come up and you can choose stock. If you want it to boot to emmc by default, just change the Default Boot Device from "CM10/10.1" to "Stock". Then it will boot to emmc if you do nothing. Then you can boot to CWM by using the cyanoboot menu.
You rock, thanks!
leapinlar said:
Ask and Ye shall receive.
Attached below is a .rar file that has four files in it. Extract those files to the boot partition of your CWM SD, replacing any duplicates. It will add the cyanoboot menu to it. It will by default boot to CWM, but if you want to boot to emmc (stock or CM10.1 on emmc), hold the n key and the cyanoboot menu will come up and you can choose stock. If you want it to boot to emmc by default, just change the Default Boot Device from "CM10/10.1" to "Stock". Then it will boot to emmc if you do nothing. Then you can boot to CWM by using the cyanoboot menu.
Click to expand...
Click to collapse
I know this thread is a bit old, but thanks! Didn't know if it would work,, but added it to my CM 10.2 SD so I could dual boot that and CarbonRom. Other than the menu having the wrong text, it works quite well.
Sent from my BN NookHD+ using Tapatalk 4
I have the Stock BN rom on DS card and have 10.2 on native install.. but an i think as far as installing the dual boot menu i got that right..
but when i try to switch to the Stock BN rom living on the SD card it just says loading SD... but never continues to the BN boot animation.. or loads continues to login... it feels like a boot loop... do i have to have root access to get this to operate... i have 10.2 root but BN SD is not rooted... confused...
i would just like a boot menu to allow the option to boot to the BN SD card or default to native 10.2..
help?
scuzzo said:
Im trying to put the Stock BN rom on DS card and have 10.2 on native install.. but an i think as far as installing the dual boot menu i got that right..
but when i try to switch to the Stock BN rom living on the SD card it just says loading SD... but never continues to the BN boot animation.. or loads continues to login... it feels like a boot loop... do i have to have root access to get this to operate... i have 10.2 root but BN SD is not rooted... confused...
help?
Click to expand...
Click to collapse
My files do not work with the systems reversed. Stock must be emmc and CM on SD. Sorry.
Sent from my Galaxy Tab 2 using XDA Premium
leapinlar said:
My files do not work with the systems reversed. Stock must be emmc and CM on SD. Sorry.
Sent from my Galaxy Tab 2 using XDA Premium
Click to expand...
Click to collapse
Right thread this time! So this is dual boot thread (sorry about earlier Leapin!).
Took me about five minutes to get where I'd made my mistakes though even after finding this and trying again. Now that I understand how this installs, and that stock must be in emmc, I just have one question....do I place CM 10.1 on the root of my SD card as a zipped, or unzipped, file for it to load from the menu? Or is there still more to do other than just "sticking the file on there?"
I know this much...every day I have greater & greater respect for xda developers. To be willing to explain things so even myself can understand it a little - and put up w questions - has to be a chore in and of itself. Thank you!
Prof24 said:
Right thread this time! So this is dual boot thread (sorry about earlier Leapin!).
Took me about five minutes to get where I'd made my mistakes though even after finding this and trying again. Now that I understand how this installs, and that stock must be in emmc, I just have one question....do I place CM 10.1 on the root of my SD card as a zipped, or unzipped, file for it to load from the menu? Or is there still more to do other than just "sticking the file on there?"
I know this much...every day I have greater & greater respect for xda developers. To be willing to explain things so even myself can understand it a little - and put up w questions - has to be a chore in and of itself. Thank you!
Click to expand...
Click to collapse
First you need to go to verygreen's SD thread and make the early 7.1 CWM card. The put the CM10.1 zip on internal memory using stock. Then boot with the CWM SD you just made and after it finishes preparing the SD, install the zip from internal memory. Then you can use the files in this thread to put the cyanoboot menu on that SD.
Sent from my Galaxy Tab 2 using XDA Premium
leapinlar said:
First you need to go to verygreen's SD thread and make the early 7.1 CWM card. The put the CM10.1 zip on internal memory using stock. Then boot with the CWM SD you just made and after it finishes preparing the SD, install the zip from internal memory. Then you can use the files in this thread to put the cyanoboot menu on that SD.
Sent from my Galaxy Tab 2 using XDA Premium
Click to expand...
Click to collapse
Ok, I seem to be / was good until I got to installing zip from internal memory. This is what has happened so far.
1. Created 7.1 CWM SD with win32 disc imager ...No probs
2. Not enough room on external card to place CM 10.1 zip file even though I started with 16 Gb....so I assumed you meant load CM 10.1 to Nook HD+ internal memory from my PC...no problem there.
3. This is where I got stuck: 7.1 card booted up just fine, but then I wasn't quite sure what next step was...found "install zip from internal SD" and tried that, but of course it sent the update - apparently - to emmc, as Cyanogenmod spinner logo now comes up after reboot.
So my question is how do I need to go about installing from internal memory once CWM 7.10 is running. Is there an adb command I'l need, or did I just choose wrong option?
Prof24 said:
3. This is where I got stuck: 7.1 card booted up just fine, but then I wasn't quite sure what next step was...found "install zip from internal SD" and tried that, but of course it sent the update - apparently - to emmc, as Cyanogenmod spinner logo now comes up after reboot.
So my question is how do I need to go about installing from internal memory once CWM 7.10 is running. Is there an adb command I'l need, or did I just choose wrong option?
Click to expand...
Click to collapse
You used the correct menu item.
If you used an sdcard version of the CM zip, it should have put it on the SD. You can tell by popping the SD out of the slot and booting. It should still boot to stock if you used the correct version. Then when you put the SD back in the slot it should boot to CM.
If you have it correct, then use the files in this thread to add the cyanoboot menu so you can boot back and forth without taking the card out.
Sent from my Nook HD+ running CM10.1 on emmc.
leapinlar said:
You used the correct menu item.
If you used an sdcard version of the CM zip, it should have put it on the SD. You can tell by popping the SD out of the slot and booting. It should still boot to stock if you used the correct version. Then when you put the SD back in the slot it should boot to CM.
If you have it correct, then use the files in this thread to add the cyanoboot menu so you can boot back and forth without taking the card out.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
Didn't use correct version...I'll have to find SD card version of CM 10, reload stock and try again.
Prof24 said:
Didn't use correct version...I'll have to find SD card version of CM 10, reload stock and try again.
Click to expand...
Click to collapse
You get the SD version the same place you got 7.1, verygreen's thread.
Sent from my Nook HD+ running CM10.1 on emmc.
Missing memory on SD CM10 boot
First post so I hope I'm putting this in the right place.
I have a Nook HD+ 32GB
I' ve started with Leapinlar's
[CWM/ROOT/EXTRAS] HD/HDplus Stock Root and other Mods
I've then used verygreen's
[Nook HD+] CM10.1 development for sdcard last update 09/04
All that seems to be fine but in CM10.1
Settings - storage reports internal memory 1GB and no SD memory or available mounts
x-plore reports /storage/emulated/0 and /Root as 850MB free of 1GB
Without the SD card - reverting to stock - I have 2.44GB used and 26.56GB available.
Is the 1GB apparently available on a partion on the SD card? I only had a 2GB SD going spare - this now has three partitions, the boot files and two others, one of 1GB. If I'd used a 32GB card would I have 31GB free?
But, more importantly, can anyone tell me how I get CM to give me my 32GB of internal storage back?
Please?
FWIW I expect to run CM10 from internal memory in the long run, but want to be sure that a couple of critical apps run OK before replacing the B&N stock.
Dave
davedamsons said:
First post so I hope I'm putting this in the right place.
I have a Nook HD+ 32GB
I' ve started with Leapinlar's
[CWM/ROOT/EXTRAS] HD/HDplus Stock Root and other Mods
I've then used verygreen's
[Nook HD+] CM10.1 development for sdcard last update 09/04
All that seems to be fine but in CM10.1
Settings - storage reports internal memory 1GB and no SD memory or available mounts
x-plore reports /storage/emulated/0 and /Root as 850MB free of 1GB
Without the SD card - reverting to stock - I have 2.44GB used and 26.56GB available.
Is the 1GB apparently available on a partion on the SD card? I only had a 2GB SD going spare - this now has three partitions, the boot files and two others, one of 1GB. If I'd used a 32GB card would I have 31GB free?
But, more importantly, can anyone tell me how I get CM to give me my 32GB of internal storage back?
Please?
FWIW I expect to run CM10 from internal memory in the long run, but want to be sure that a couple of critical apps run OK before replacing the B&N stock.
Dave
Click to expand...
Click to collapse
Everything is as it should be. You only have 1GB for 'sdcard' since you only used a 2GB SD. If you had used a 32GB, you would have close to 31GB for 'sdcard'.
And on an SD install, the internal memory is still there but not as 'sdcard'. It shows as a folder named 'emmc'.
Since you are planning on installing CM to internal memory, it will be even different yet. 'Sdcard' will be your internal memory and your external SD will be shown as ext_sdcard.
And do not pay too much attention to the settings/storage. People get very confused when reading that since it mixes apples and oranges. (Media storage and app storage).
Sent from my Galaxy Tab 2 using XDA Premium
leapinlar said:
Everything is as it should be. You only have 1GB for 'sdcard' since you only used a 2GB SD. If you had used a 32GB, you would have close to 31GB for 'sdcard'.
And on an SD install, the internal memory is still there but not as 'sdcard'. It shows as a folder named 'emmc'.
Since you are planning on installing CM to internal memory, it will be even different yet. 'Sdcard' will be your internal memory and your external SD will be shown as ext_sdcard.
And do not pay too much attention to the settings/storage. People get very confused when reading that since it mixes apples and oranges. (Media storage and app storage).
Sent from my Galaxy Tab 2 using XDA Premium
Click to expand...
Click to collapse
Finally...it worked! Thanks leapinlar, for all your help!
I encountered the situation above and am wondering if, say, instead of the 2GB card I use a 16 GB...that gives me 16 GB of storage for the CM 1.0 tablet, and my regular flash storage also stays 16 GB? Or all the apps are by default stored on the emmc?
Prof24 said:
Finally...it worked! Thanks leapinlar, for all your help!
I encountered the situation above and am wondering if, say, instead of the 2GB card I use a 16 GB...that gives me 16 GB of storage for the CM 1.0 tablet, and my regular flash storage also stays 16 GB? Or all the apps are by default stored on the emmc?
Click to expand...
Click to collapse
On the SD install, both media and apps get stored on the SD. If you use a 16GB SD to install CM to, it will have about 15GB available for media and app storage instead of 1GB on the 2GB card. But 2GB is really too small to be running CM. You will be running out of app and media storage very quickly.
Since you will be dual booting, when booted to stock the media and apps will be stored on internal memory. You will either have 13GB or 28GB available on stock on emmc depending on the size of the device (16 or 32GB model).
Sent from my Nook HD+ running CM10.1 on emmc.
Updating SD version of CM 10.1
I know I've seen this elsewhere, but can't find it...if I go to update the rom on the SD card, it makes sense to me that I would need to load the latest SD version from verygreen's page...or can I just update from settings and not lose dual boot? Also, will a dirty install work so that the data is not lost? (backups are always good )
Man we're enjoying dual boot. My Acer a500 is unreliable so I backed the "build a city town park" up with Helium app. Long story short, with dual boot my kid and I get to continue building and enjoying our monsters in "Monsterama Park" by booting to CM 10.1and restoring data, yet I don't have to give up some of the reader features that I really like with the original Nook OS. Marvelous find....again, thanks y'all for the hard work!
Prof24 said:
I know I've seen this elsewhere, but can't find it...if I go to update the rom on the SD card, it makes sense to me that I would need to load the latest SD version from verygreen's page...or can I just update from settings and not lose dual boot? Also, will a dirty install work so that the data is not lost? (backups are always good )
Man we're enjoying dual boot. My Acer a500 is unreliable so I backed the "build a city town park" up with Helium app. Long story short, with dual boot my kid and I get to continue building and enjoying our monsters in "Monsterama Park" by booting to CM 10.1and restoring data, yet I don't have to give up some of the reader features that I really like with the original Nook OS. Marvelous find....again, thanks y'all for the hard work!
Click to expand...
Click to collapse
Do not use settings to update an SD install. It will try to put the new ROM on internal replacing stock. Go get the latest SD ROM from the verygreen thread. You can dirty install it with the SD install's CWM.
Sent from my Nook HD+ running CM10.1 on emmc.
So there is no way to switch the menu for stock on sdcard?
leapinlar said:
Do not use settings to update an SD install. It will try to put the new ROM on internal replacing stock. Go get the latest SD ROM from the verygreen thread. You can dirty install it with the SD install's CWM.
Sent from my Nook HD+ running CM10.1 on emmc.
Click to expand...
Click to collapse
I'm a little confused. I've put verygreens stock on sdcard and have cm 10.2 on emmc. If the images are renamed can you boot with the menu into stock on sd or cm 10.2 from emmc? If not is there a second solution?
krash1256 said:
I'm a little confused. I've put verygreens stock on sdcard and have cm 10.2 on emmc. If the images are renamed can you boot with the menu into stock on sd or cm 10.2 from emmc? If not is there a second solution?
Click to expand...
Click to collapse
It does not work on that configuration and there is no solution.
Sent from my BN NookHD+ using XDA Premium HD app