Related
I tried to soft reset my tytn II in the dark, and accidently put the stylus into the usb/charging slot and somehow screwed up my phone. It will not charge, or connect with my computer. Any suggestions?
OMG! I did the same thing, but luckily i didn't do further damage except the copper parts become bent
HTC should have done something about this! i am sure many other users did the same
can u take it back to your supplier for warranty claim?
same problem here...
i could bend back the copper contacts with a WOODEN (!!) toothpick (dont steer around with metal in there....)
Looks like i tried to reset the device in darkness last night and fumbled around in the usb jack.
Damn... really bad position for the reset-button!
Same issue here-- though some chargers now work, some don't. My phone will charge with my OEM charger and usb to computer, but not my 3rd party wall charger or my car charger. Aaargh
Same Problem Here
Check out this thread at AT&T Forum regarding my attempt to get a replacement phone.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=65536
I got mine replaced at the store. I was under 30 days and was lucky.
I am going to order one of these:
http://www.eforcity.com/silicone-mini-5-pin-plug-for-motorola-v3-2-pc-smoke-cmotv3xxpc01.html
it should fit. i also heard that certain verizon phones have rubber usb plugs on them. I may just stop in a verizon store and see if one fits. My tmobile wing had one on it and it worked great to protect the usb port.
Well...I did the samething last night. Tried to soft reset my phone while driving in the dark. Luckily I've had my tilt less than 30 days, called and now all I have to do is go to the AT&T store for a replacement....Also, I'm going to pay 10% restocking fee so I can get an extra battery and charger...W00T!!!!! I actually saved about 50 bux
One way to avoid doing this in the dark is to flip the phone upside down, locate ExtUSB socket with your left index finger, keep your finger over the socket and slide your stylus down your finger tip. Of course the easiest way is to turn a light on.
wizzzard said:
One way to avoid doing this in the dark is to flip the phone upside down, locate ExtUSB socket with your left index finger, keep your finger over the socket and slide your stylus down your finger tip. Of course the easiest way is to turn a light on.
Click to expand...
Click to collapse
true, but for those of us with this problem already, it is too late
Luckily, I tried a newer charger, and my car charger, and they both work. As far as connecting to my computer, I have to use my Y cable that was included with my old 8525. I'm still pissed, and I have a TyTn II and not a tilt, so warranty will be a pain in the ass, considering I have to send it to the UK. If it starts to act up, I will have to send it in, and if I get it fixed, I will definitely buy one of those plugs from the above post. Thanks for all the replies, and good luck to everyone with this problem.
Lesson # one don't put things in holes in the dark in bed
Well, good news is ATT is sending me out a replacement phone for free since I am still under warranty (outside the 30 days, but inside the 1-year). Now I just need to re-flash back to OEM status so I don't get busted on the return...time to test out the "Idiot's Guide to Re-Flashing Back to Original ROM" and see if it does me right.
Heijdemann said:
Lesson # one don't put things in holes in the dark in bed
Click to expand...
Click to collapse
that's why I have so many kids!?! anyways I had my phone charging in my car and it fell of my seat onto the floor. the nezt day I noticed it wasn't charging (tytn 2 no easy warranty fix) I then noticed that inside the usb thing is a black plastic piece with the small metal connections. the black piece was bent a little on one side so I removed the battery took a pair of tweazers and bent it it straight again than I took some forced air in a can (for a computer keyboard) and blew in there to make sure none of that cheap plastic shredded and got in the way of the metal connections. it looked like after I used the tweazers some of that black plastic chipped off (very small pieces) anyways after that it worked perfectly. hopefully this will help others
well it seems i messed up now and stuck my stencil in there one of the small Metal wires is out of whack now ad some chargers work and some dont did anyone get a plug yet?
pissed
so I live in metro detroit with a tytn 2 not a tilt. after I stuck my stencil in there it seems my car charger don't work. when charging with my audio adapter its flaky losing some power, maintaining, gaining some power. but when I use my wall charger with no adapter it charges!! if you put the kaiser flat on the table I see by 2nd wire (in the hole) is bent down(whereas the others are up) and its sitting in the middle of the whole.(my buddy told me to use a needle and a magnify glass because the 2nd wire was actually bent all the way down but I got it in the middle after messing with it. when that one wire was out of whack my car charger gave me a red constant light (no charge) after the stencil incident. I hope all that helps somebody! anyways so I call HTC first they tell me that's not covered under warranty. Then they tell me I have to send it to houston tx for 3 weeks. Then they tell me it will cost $300 usd to repair!!!! this is insane for a little miniusb piece that got hit once with a stencil. it probaly cost 22cents. what is everyone else doing? I think if I can get that metal piece to stick to the top it'll be fine. I just switched to att and I have 6 days until im locked to a 1yr contract I could buy a tilt for 250 or whatever but id have to sign a 2yr contract.
I stuck the stylus in the USB port as well but luckily I didnt seem to do any damage. I did bend it a bit but with some gentle pressure in the opposite direction it went back into place. I havent had any problems charging or syncing since then, so it seems I got lucky. Just gotta hope I dont do it again, lol.
ya the black piece as a whole seems to be able to bend a little but if u mess the little little metal connections in there you're gonna have problems
Hi, this is my first post and I hope to help someone. I had the same problem with my phone, it charged with the home charger and in the cradle but the car charger won't work. using a close light and a magnifier I could notice that with the phone with the screen upside looking at the usb connector that the pin al the way to the right was flat and a tip was showing as opposite to the others. I returned it to the former position and voila!! it works. I hope to help someone.
>>>>>><<<<<< PDF With All Steps And Images Added For Your Viewing/Downloading Pleasure >>>>>><<<<<<
***If this does not belong here I appologize, and feel free to move this if necessary. I just figured the development community is most likely to take this "upgrade" on***
After seeing that someone used Palm's wireless charger on their non-palm phone; I decided to put one on my Droid Incredible.
***This was done to a completely stock Dinc. I did not use any special back, and the stock back gets to stay on (unlike in the other video that I saw)
Wireless Charging the Droid Incredible
**Disclaimer: This will void your warranty, and if you solder something wrong will probably break your phone. With that said I can in no way be held accountable for anything that occurs while performing this “upgrade” to your phone.
>>>>If anyone knows where I can buy that little void sticker that you will see in a picture below, please let me know! If we can get that sticker then our warranty is not voided by doing this.
Supplies:
1.Palm touchstone charger http://www.shopping.hp.com/product/handheld/categories/palm/4/accessories/FB300AA%23AC3
2.Palm touchstone phone back http://www.shopping.hp.com/store/product/product_detail/FB306AA%23AC3?
3.Micro USB cable
4.Soldering Iron (the finer the tip on this the better)
5.Torx T6 screw driver
6.Safe pry tool (or a small flat head screwdriver)
7.Very tiny insulated wires (I just pulled mine out of a USB cable that I cut up)
8.Electrical Tape
9.[Optional] Multimeter to test that you actually made a good connection
How To (Images are of a higher quality (12mp) so I had to stick them in zip files to get them on here):
1.The palm touchstone phone back has a sticker inside of it that encases the wireless charging receiver, so you need to peel this off. Once it is peeled off it will look like this (without the wires soldered onto it):
(Images can be seen in: Palm Receiver.7z)
2.Remove the battery cover and the battery then unscrew the back from your phone (please view a tare down video for details, there are plenty of them on you tube that I used for a reference.)
1.All you need is a torx t6 screwdriver and a safe pry tool, I used a small flat head screwdriver and it worked just fine. Unscrew the 4 screws around the sides and then carefully pry off every place that the battery cover clips on, as they also hold on the red back.
(Images can be seen in: Dinc Inside.7z)
3.Solder on some wires to the USB connector as shown in the below image without soldering onto the pins next to them. This is difficult and takes some time and patience, since these connectors are very small and close (note the polarity in the image, notated in red).
A.Also it is necessary to place a piece of electrical tape over the components right next to the connector (Green box in the image) as they will short out the power and make it impossible to charge your phone if you do not (I found that out the hard way and went back and fixed it).
B.One final note here is that I had to melt down the red phone backing inside to allow the cables to get past the case. See the green rectangle in the image above for where I had to do that. I just used my soldering iron and melted it down, it makes a pretty nice indention for the wires to fit through.
(Images can be seen in: Dinc USB.7z)
4.Now push out the rubber plug in the red phone backing next to the USB cover (this is encircled in Green in the image from step 2).
A.Run the cables that you just solder on through that so that they are sticking through to the battery compartment on your phone.
B.You can also stick on the palm receiver to the inside of your phone cover (note the direction and placement, as this is necessary to close your cover).
3.Note that I placed electrical tape over the wires. This was necessary to keep them from breaking off of the USB connector since the solder points are so small.
(Images can be seen in: Almost Done.7z)
5.Solder on the wires to the palm charger receiver and you are done. Now you just need to carefully place the wires towards the middle of the phone so that you can close the back of your phone entirely (this is another reason why the wires need to be small).
A.Note the polarity of the connection.
B.Also I put a piece of electrical tape over the connections on the palm charger receiver to protect them (not shown in the image).
(Images can be seen in: Wireless Charger.7z)
Here is a video of the end product and how it works:
http://www.youtube.com/watch?v=YOMVJ-vmWpg
Also I just verified that my compass is working without any problems.
This could be truly amazing. I can't wait to see more.
ThugEsquire said:
This could be truly amazing. I can't wait to see more.
Click to expand...
Click to collapse
Its been done with the Evo, but don't know anyone who did it with the Inc.
http://www.goodandevo.net/2010/06/h...rk-with-palm-touchstone-wireless-charger.html
Sounds really nice. Not gonna try it with mine because I'm too scared
Though shouldn't this be in accessories or general?
What are you doing to align the coils? My biggest concern that's kept me from this is the magnets also would mess up the compass sensors readings which I for one actually value.
Wow, you managed to bring me out of my months of silence in posting...
I feel honored that I can get you out of your months of silence
The coil alignment is handled by the magnets inside of the palm touchstone charger itself (the base unit that plugs into the wall). The metal objects that you can see in the "Palm Receiver.7z" file are actually not magnets, but small circular pieces of metal that get pulled towards the charger base when you get them close to each other. So when you have the phone off of the charger, there are no magnets to mess with anything
Also you will notice that there is a piece of metal behind the coil, and that seems to block the inductive signal all together (because I tried to put it on backwards to no avail). Therefore your phone is mostly protected from the inductive transmission.
The only thing that I noticed, is that the touchscreen on the phone is a little weird when it is on the charger, but I see the same side effects when plugging the phone into a "non-htc" charger (before performing this "upgrade"). **I also saw this on my Moto Droid when connecting it to a 1 amp charger, and I have seen this with multiple other touchscreen devices so I think it just has something to do with the frequency of the charger.
Also in case of any concerns: MY PHONE HAS IN NO WAY BEEN DAMAGED BY THIS "UPGRADE"
pianoplayer said:
Sounds really nice. Not gonna try it with mine because I'm too scared
Though shouldn't this be in accessories or general?
Click to expand...
Click to collapse
Yah, it probably should be, and may get moved (which is perfectly fine by me). I put it in here because I am a developer and much more likely to do this, so I figured the development community would be more interested.
ThugEsquire said:
This could be truly amazing. I can't wait to see more.
Click to expand...
Click to collapse
You mentioned that you can't wait to see more....?
What more would you like to see? I am happy to add to the posts, but just not sure what further details you would like to see.
nevetsvsx said:
Also in case of any concerns: MY PHONE HAS IN NO WAY BEEN DAMAGED BY THIS "UPGRADE"
Click to expand...
Click to collapse
I trust your method, I just don't trust my shaky hands
BTW there is a multi quote button so you dont have to do a separate post for each reply
I have a rubber case on my Dinc... would I need to remove it for charging?
___________________________________
Yup.... The ones yoe momma told ya about.... Bad Seed Customs!!
I think you will be ok if it is one of those thin (about 1mm thick) rubber cases. Anything thicker than that and you would probably have to install the wireless receiver on the case itself and remove your battery cover all together.
I tested a thin rubber case that I have (no more than 1mm thick I think) that fits a Droid Eris and it charges as long as its flush to the back of my phone.
Sent from my ADR6300 using XDA App
Wow, this is amazing, very well done. I think this is the first hard mod I've heard of for an Android. I guess gold cards were a sorta gray area.
I've had my Incredible modded to work with a Touchstone since around June of last year. It works great, but I must caution anyone thinking of doing this to be VERY careful. Experience with soldering and a steady hand is a must. One could fairly easily mess up their phone attempting to do this.
Could you do this with a powermat if you wanted to? I have a few laying around I could use.
Sent from my ADR6300 using XDA App
Paul600k5 said:
Could you do this with a powermat if you wanted to? I have a few laying around I could use.
Sent from my ADR6300 using XDA App
Click to expand...
Click to collapse
Sure, if you wanna take apart one of those generic receivers and try to fit it inside your phone!
nevetsvsx said:
You mentioned that you can't wait to see more....?
What more would you like to see? I am happy to add to the posts, but just not sure what further details you would like to see.
Click to expand...
Click to collapse
What I originally meant was pictures. But now that you've added them and I've seen the glory, this mod is really quite impressive and I'm thrilled you shared it with us. But now that I think about it, could this also do USB wirelessly? That would be pretty amazing.
ThugEsquire said:
What I originally meant was pictures. But now that you've added them and I've seen the glory, this mod is really quite impressive and I'm thrilled you shared it with us. But now that I think about it, could this also do USB wirelessly? That would be pretty amazing.
Click to expand...
Click to collapse
No, the transmission of data wirelessly is achieved through modulated EM waves. This is simple inductance: a changing electric field creates a magnetic field, a changing magnetic field generates an electric field, so a current carrying loop placed near another loop of wire will induce current in the other loop. The receiver in the phone is engineered to "create" the "proper" amount current to charge your battery when combined with the base. In theory yes, but not with this equipment.
How does the phone treat a USB cable being plugged in - will it charge ok, and have your data transfer rates been adversely effected? I wouldn't think so, since you're only touching the power...
Mr. Spontaneous said:
How does the phone treat a USB cable being plugged in - will it charge ok, and have your data transfer rates been adversely effected? I wouldn't think so, since you're only touching the power...
Click to expand...
Click to collapse
I have used the USB charger and data transfer cables without any problems at all. Also I have copied some files off of my phone to my PC since the "upgrade" and did not notice any extended times or anything that would remotely make me think something was wrong.
I did not run a speed test before and after to see if anything slowed down, but as you said we are only touching the power pins, so I highly doubt anything has changed.
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
KillerbawX said:
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
Click to expand...
Click to collapse
You could probably buy two new Raiders for $250! Replacement might be the best bet, as you can likely find one on Kijiji for $100 or so. If you have a local cell repair joint, give them a call, and see if they offer the replacement. It might be tricky since the USB on the Raider (as other HTC phones) is actually a special type of HDMI jack that also has USB (known as MHL).
If you're adventurous, you might track down a broken Raider and attempt a part swap yourself. I've not seen the inside of the unit, so I can't say how easy or hard that would be at any skill level...
Hope you get it fixed up!
The part is on eBay you can always try to do it yourself should be a few small solder points
Sent from my HTC PH39100 using xda premium
KillerbawX said:
Any one know of a company that can fix the USB port on a HTC Raider in Canada. Rogers wants to charge me $250 to fix it.
Click to expand...
Click to collapse
A friend needed this. We ordered one off ebay ( http://www.ebay.com/itm/OEM-USB-Pow...328529?pt=PDA_Accessories&hash=item27c422a1d1 ) and although it required opening the phone up and voiding the warranty, it required no soldering. He doesn't open electronics up very often, and said it wasn't very hard to do.
i was babbling abt this in a thread in the dev forum, thot i'd best do it also here in the proper forum for it:
i changed the USB port in my Raider, was very simple. Six little screws, two different lengths so keep track of them. One screw also holds down the teeny cover under which is where the tiny connector resides that connects the port to the fone circuit board. Once the fone is back together that's where you make the final connection between port and fone.
Slip off the battery cover, undo the six screws, take off that tiny little cover. Carefully work off the entire back housing. There's no front housing, just the screen glass and the fone circuitry bundled together.
Micro-USB port and ribbon connector is fastened to the housing with two more of those little screws. Change out the port with the new one. New part may not be an exact duplicate of the old part: that's ok. Reassemble the fone. Under that hole left by the tiny cover, press home the miniscule plug that connects up the port to the fone.
Put back the tiny cover, fasten back all the screws, and you're done. Port cost me $9 USD plus shipping on ebay.
lowfatmilk said:
i was babbling abt this in a thread in the dev forum, thot i'd best do it also here in the proper forum for it:
i changed the USB port in my Raider, was very simple. Six little screws, two different lengths so keep track of them. One screw also holds down the teeny cover under which is where the tiny connector resides that connects the port to the fone circuit board. Once the fone is back together that's where you make the final connection between port and fone.
Slip off the battery cover, undo the six screws, take off that tiny little cover. Carefully work off the entire back housing. There's no front housing, just the screen glass and the fone circuitry bundled together.
Micro-USB port and ribbon connector is fastened to the housing with two more of those little screws. Change out the port with the new one. New part may not be an exact duplicate of the old part: that's ok. Reassemble the fone. Under that hole left by the tiny cover, press home the miniscule plug that connects up the port to the fone.
Put back the tiny cover, fasten back all the screws, and you're done. Port cost me $9 USD plus shipping on ebay.
Click to expand...
Click to collapse
Hey, dude, I know this thread is a little old, but can you PM me the link to where you bought your USB port? I think I need to replace my port (issues connecting to PC and charging requires wire wiggling), but I've read about certain ports not working with data transfer and only charging, and I don't want to make that kind of mistake.
projectisaac said:
Hey, dude, I know this thread is a little old, but can you PM me the link to where you bought your USB port? I think I need to replace my port (issues connecting to PC and charging requires wire wiggling), but I've read about certain ports not working with data transfer and only charging, and I don't want to make that kind of mistake.
Click to expand...
Click to collapse
Try this? Says OEM so I imagine you wont lose functionality.
http://www.globaldirectparts.com/product-p/htc747235-qs.htm
Thank you! And only $8 too
Sent from my Vivid 4G using xda app-developers app
Heres the backround on what i did to get wireless charging going...
1) get palm coil and touchstone. i bought this on ebay for 10$ (just search touchstone charging kit)
2) carefully remove the coil from the back cover of the palm phone. plastic cover first then the rest.
3) what worked easiest for me was to keep all the coil stuff stuck to the removable plastic piece holding everything together, then you can simply stick it in the back of our active covers. (make sure when moving the magnets all the positive sides are facing towards the dock)
4) Connecting it. I tried doing this a couple different ways and i eventually ended up pulling tiny copper wire out of computer speaker cable and used it like a twist tie on the phone terminals (then small amount of electrical tape to separate them...which worked out fine)*I attempted to do the same on the coil side of the connection but that was a bust so i ended up soldering it.. not my first choice but since its on the palm coil not my active I did it.*
5) you should be all good to go at this point
here are some pics too and of course if you some of mess your phone up...its not my fault
Video- http://www.youtube.com/watch?v=BvO01b1CKBk
feel free to pm if ya got a question me... I am leaving the country tomorrow night for a week, but ill try to get back to ya
happy modding
in the picture with highlighting yellow goes to left phone terminal(positive) and brown goes to right teminal (negative)
bdgarel said:
Heres the backround on what i did to get wireless charging going...
1) get palm coil and touchstone. i bought this on ebay for 10$ (just search touchstone charging kit)
2) carefully remove the coil from the back cover of the palm phone. plastic cover first then the rest.
3) what worked easiest for me was to keep all the coil stuff stuck to the removable plastic piece holding everything together, then you can simply stick it in the back of our active covers. (make sure when moving the magnets all the positive sides are facing towards the dock)
4) Connecting it. I tried doing this a couple different ways and i eventually ended up pulling tiny copper wire out of computer speaker cable and used it like a twist tie on the phone terminals (then small amount of electrical tape to separate them...which worked out fine)*I attempted to do the same on the coil side of the connection but that was a bust so i ended up soldering it.. not my first choice but since its on the palm coil not my active I did it.*
5) you should be all good to go at this point
here are some pics too and of course if you some of mess your phone up...its not my fault
Video- http://www.youtube.com/watch?v=BvO01b1CKBk
feel free to pm if ya got a question me... I am leaving the country tomorrow night for a week, but ill try to get back to ya
happy modding
in the picture with highlighting yellow goes to left phone terminal and brown goes to right
Click to expand...
Click to collapse
This video seems very helpful with the process, just wish i knew which side was pos and which is neg http://www.youtube.com/watch?v=jHw1QIPwkZU
EDIT: i see the pics thank that helps!
joshuadjohnson22 said:
This video seems very helpful with the process, just wish i knew which side was pos and which is neg http://www.youtube.com/watch?v=jHw1QIPwkZU
EDIT: i see the pics thank that helps!
Click to expand...
Click to collapse
Use a multimeter...if you dont know how, you probably shouldn't attempt this hack and should wait for an aftermarket back plate to come out
Out of curiosity, how strong are these magnets? Am I going to have to make sure that my phone gets nowhere near my credit cards (and other magnetic cards, media, etc.)?
jt3 said:
Out of curiosity, how strong are these magnets? Am I going to have to make sure that my phone gets nowhere near my credit cards (and other magnetic cards, media, etc.)?
Click to expand...
Click to collapse
They are fairly strong but I have yet to have any issues with my cards...however I usually keep my phone in a separate pocket
Have you tested the phones waterproof capabilities since you did this mod? I love the idea, want to do it, but im on the fence, as it seems it would make it very easy to make the waterproofing gasket fail with a small wire.... on the other hand, you dont have to take the back off, or open the charging port, so if it doesn't void the waterproofing, it could be even better
Obviously, if any wire or any part of the wireless receiver protrudes over the seal, the water resistance will be compromised, but that's not the only issue.
In the back panel replacement sticker on the back of the S4A, it tells you to press under the camera LED. Pressing there engages the rubber seal. The issue is that any of these non-oem wireless receivers is going to slightly lift the central portion of the back away from the phone. Thus, even if no part of the seal-line is breached, I still wouldn't trust that the seal could engage fully.
Don't get me wrong... I'm going to do something similar, since I'd rather have wireless charging. Still... until an OEM wireless charging backplate comes from Samsung, I'd assume it's an either/or situation. Wireless charging OR water resistance.
jt3 said:
Obviously, if any wire or any part of the wireless receiver protrudes over the seal, the water resistance will be compromised, but that's not the only issue.
In the back panel replacement sticker on the back of the S4A, it tells you to press under the camera LED. Pressing there engages the rubber seal. The issue is that any of these non-oem wireless receivers is going to slightly lift the central portion of the back away from the phone. Thus, even if no part of the seal-line is breached, I still wouldn't trust that the seal could engage fully.
Don't get me wrong... I'm going to do something similar, since I'd rather have wireless charging. Still... until an OEM wireless charging backplate comes from Samsung, I'd assume it's an either/or situation. Wireless charging OR water resistance.
Click to expand...
Click to collapse
I will fix the wire issue by using copper tape. I'm excited to try it...
I am doing this mod tonight and I thought I would share some information.
See below for the information I have gathered:
Yellow lines = Copper tape- as you can tell it gets very cramped around the end because of the gasket. I may need to use a different path or wires like the OP. The important stuff to gather from this is which is positive and which is negative on both the phone and the palm pre touchstone.
Nice idea, curious to see how this works out.
Update
My copper tape has not arrived but I installed everything else. It does appear that the coil makes the rear housing push out which leads me to believe it will not do well to repel water away from the seal during extended use but I would prefer wireless charging
If you plan on using a case I would recommend ordering stronger magnets from supermagnets.com part number Disc - D1046. These should work well with any case and it will fit more snug because they are a lot stronger. I will update with photos once the copper tape is installed and everything is working.
Am I missing something? Why doesn't the Samsung wireless charging kit work or the wireless receiver tags you can get for the S4 so you can use a Qi charger?
Sent from my SGH-I337 using Tapatalk 2
holysnikey said:
Am I missing something? Why doesn't the Samsung wireless charging kit work or the wireless receiver tags you can get for the S4 so you can use a Qi charger?
Sent from my SGH-I337 using Tapatalk 2
Click to expand...
Click to collapse
The battery door is different. In theory it will work but you would have to figure out a way to gut the back plate and that would be a lot harder than palm's touchstone mod. Or just wait for the active's wireless back plate to be released. This is a lot cheaper IMO $10 vs $30-150
Ya I just realized this. But still do you think the wireless charger receiver tag could work? If you search on Amazon or Ebay "Galaxy S4 wireless charging receiver tag" there's the component which is stuck inside the back cover Samsung is selling. Except it can be bought for $10-20 and most likely can fit in the Active. I don't know because I have the original S4 but just trying to throw out some ideas. In theory if the tag works you can get it for $15 then use any Qi charger and you're good. While not quite as cheap it's only a few bucks more and much easier and looks way better probably. That is if it works of course.
Sent from my SGH-I337 using Tapatalk 2
holysnikey said:
Ya I just realized this. But still do you think the wireless charger receiver tag could work? If you search on Amazon or Ebay "Galaxy S4 wireless charging receiver tag" there's the component which is stuck inside the back cover Samsung is selling. Except it can be bought for $10-20 and most likely can fit in the Active. I don't know because I have the original S4 but just trying to throw out some ideas. In theory if the tag works you can get it for $15 then use any Qi charger and you're good. While not quite as cheap it's only a few bucks more and much easier and looks way better probably. That is if it works of course.
Sent from my SGH-I337 using Tapatalk 2
Click to expand...
Click to collapse
that would probably work... if i understand it correctly...
That's the image of what I'm talking about. The official back plate you buy from Samsung is just the battery door with that tag glued on the inside of the door.
holysnikey said:
That's the image of what I'm talking about. The official back plate you buy from Samsung is just the battery door with that tag glued on the inside of the door.
Click to expand...
Click to collapse
It probably will work but it will cost a lot more than this mod we are talking about. It will be a lot easier to install though
holysnikey said:
That's the image of what I'm talking about. The official back plate you buy from Samsung is just the battery door with that tag glued on the inside of the door.
Click to expand...
Click to collapse
I went ahead and order this 2, so we will see
joshuadjohnson22 said:
I went ahead and order this 2, so we will see
Click to expand...
Click to collapse
Same here. Amazon. 14.99
jdminpdx said:
Same here. Amazon. 14.99
Click to expand...
Click to collapse
I paid a little more because I wanted to get it this week. The cheaper ones come from China and may take a while. I now need a replacement back for my active, somehow with the palm mod one of my clips doesnt work any longer so under my volume rocker it is propped up. Excited to have wireless charging. Hopefully this week
Sent from my SAMSUNG-SGH-I537 using Tapatalk 4 Beta
The charging speed is absolutely mental, the 0 -100% in 30 minutes is legit.
But one thing to note, the cable itself shouldn't be kinked, I've had a few of these before and you can break them fairly easy if you wrap up your cables all the time, try to leave it as loose and straight as possible.
Besides that, I'm so impressed by the speed of this charger, it goes like hell.
Avoid pulling* on them except by grasping the plug housing. Where the cable meets it are the weakest link. Never bend the cable there.
That's the spot where most fail.
*including phone saved by cable drops
blackhawk said:
Avoid pulling* on them except by grasping the plug housing. Where the cable meets it are the weakest link. Never bend the cable there.
That's the spot where most fail.
*including phone saved by cable drops
Click to expand...
Click to collapse
My wife has an Asus portable screen and the cables the same grade, she folded it up for transporting to work, after that it didn't work. The 10 pro one is very similar, just shouldn't be bent at all.
And of course don't use your phone while charging...
notnoelchannel said:
And of course don't use your phone while charging...
Click to expand...
Click to collapse
Or swimming whilst charging
In all fairness though, this phone remains so cool, I'm super impressed by it.
dladz said:
My wife has an Asus portable screen and the cables the same grade, she folded it up for transporting to work, after that it didn't work. The 10 pro one is very similar, just shouldn't be bent at all.
Click to expand...
Click to collapse
I have 2 stock Samsung cables that came with the bricks. One has been used well over 2000 times but it is never put away... it just sits there.
It's a stiff cable, never expected this kind of longevity from it. It's taken a few "drops" too.
A well designed/built cable/plug assembly shouldn't fail from simply coiling* it. I've fabricated many hundreds of custom cable assemblies, many still in use after over a decade.
*coiling verses sharp bends to jam it into a small space. I'm not concerned with saving shipping space but rather delivering the assembly in best condition. I also avoid using kind of tight binding of the coil that could deform the cable's internal structure. Teflon insulation is extremely susceptible to this.
Should be faster!
I charge my 9 pro (65w wall charger) from 0-100% in 27 minutes. With the phone OFF.
I recomend to everybody to buy wireless charger 50w. The model for 9 Pro. Is Very Fast and it saves usb_C port a lot.
Atention! You still need wall charger and OnePlus cable to work. When you buy the wireless charger does not come with wall charger and cable in the box.
null0seven said:
Should be faster!
I charge my 9 pro (65w wall charger) from 0-100% in 27 minutes. With the phone OFF.
I recomend to everybody to buy wireless charger 50w. The model for 9 Pro. Is Very Fast and it saves usb_C port a lot.
Atention! You still need wall charger and OnePlus cable to work. When you buy the wireless charger does not come with wall charger and cable in the box.
Click to expand...
Click to collapse
27 minute's?
null0seven said:
Should be faster!
I charge my 9 pro (65w wall charger) from 0-100% in 27 minutes. With the phone OFF.
I recomend to everybody to buy wireless charger 50w. The model for 9 Pro. Is Very Fast and it saves usb_C port a lot.
Atention! You still need wall charger and OnePlus cable to work. When you buy the wireless charger does not come with wall charger and cable in the box.
Click to expand...
Click to collapse
C ports can be quit durable* if kept clean (rarely need cleaning). They typically last many years and thousands of charge cycles. You'll likely replace 2 or more batteries before a C port.
Typically the C port is easier to replace than the battery. A heavily used device's battery will last 1 to 2 years at best.
Direct charging is faster and generates less heat. High temperature and cell voltage are an Li's prime premature degraders.
*at least on a Samsung N10+
blackhawk said:
C ports can be quit durable* if kept clean (rarely need cleaning). They typically last many years and thousands of charge cycles. You'll likely replace 2 or more batteries before a C port.
Typically the C port is easier to replace than the battery. A heavily used device's battery will last 1 to 2 years at best.
Direct charging is faster and generates less heat. High temperature and cell voltage are an Li's prime premature degraders.
*at least on a Samsung N10+
Click to expand...
Click to collapse
Yea I've had a problem with lint, just cleaned it, way more robust than micro..
They were horrific .
In regards to charge speed. The 80w 10 pro charger is the fastest I've ever used, it's insane
dladz said:
Yea I've had a problem with lint, just cleaned it, way more robust than micro..
They were horrific .
In regards to charge speed. The 80w 10 pro charger is the fastest I've ever used, it's insane
Click to expand...
Click to collapse
The micro's were nightmares. C ports will take some abuse without becoming loose.
The lint problem is likely a result of where it's kept. My N10+ nests in my lint free bdu pant pocket however I was keeping my Buds+ in my front pants pocket (cotten vs polyester/cotton).
Recently had to clean the lint out of the Buds+ case. It wasn't properly seating.
No big deal, carefully used a toothbrush and blew it out with a blower bulb. Now that case nests in my cargo pocket too
In spite of no cover cap the N10+'s C port has stayed remarkably clean in over 2 years of heavy usage in a dusty environment. Where you pocket the device counts the most in keeping the C port clean it appears. A dust repelling case with a slightly over hanging hood seems to help as well.
blackhawk said:
The micro's were nightmares. C ports will take some abuse without becoming loose.
The lint problem is likely a result of where it's kept. My N10+ nests in my lint free bdu pant pocket however I was keeping my Buds+ in my front pants pocket (cotten vs polyester/cotton).
Recently had to clean the lint out of the Buds+ case. It wasn't properly seating.
No big deal, carefully used a toothbrush and blew it out with a blower bulb. Now that case nests in my cargo pocket too
In spite of no cover cap the N10+'s C port has stayed remarkably clean in over 2 years of heavy usage in a dusty environment. Where you pocket the device counts the most in keeping the C port clean it appears. A dust repelling case with a slightly over hanging hood seems to help as well.
Click to expand...
Click to collapse
Exactly mate.
I've never broken one before, the cable itself though, very stiff, I've broken then before.
dladz said:
Exactly mate.
I've never broken one before, the cable itself though, very stiff, I've broken then before.
Click to expand...
Click to collapse
I have 2 Samsung C cables, one is 2.5 yo, the other over a year, both are used constantly. Both are very stiff, I never coil them.
The have aged well, which pleasantly surprises me.
Micro cables, always was replacing them... like dumb bunnies
blackhawk said:
I have 2 Samsung C cables, one is 2.5 yo, the other over a year, both are used constantly. Both are very stiff, I never coil them.
The have aged well, which pleasantly surprises me.
Micro cables, always was replacing them... like dumb bunnies
Click to expand...
Click to collapse
I've seen someone buy a phone, I was working in a phone repair shop and she bought the really expensive Sony phone. She was quite rough with it, shoved the micro usb cable into it the wrong way several times, broke off most the pins, literally list 1200 quid on the spot.
I think that's partly why usb c became a thing, so much more reliable, it's design I'm referring to. I know power delivery was it's driving force and data rate.
dladz said:
I've seen someone buy a phone, I was working in a phone repair shop and she bought the really expensive Sony phone. She was quite rough with it, shoved the micro usb cable into it the wrong way several times, broke off most the pins, literally list 1200 quid on the spot.
I think that's partly why usb c became a thing, so much more reliable, it's design I'm referring to. I know power delivery was it's driving force and data rate.
Click to expand...
Click to collapse
Some people...
Yeah never liked the polarized micro system. A good sideways pull or drop on the attacted charging cable could loosen them.
It was like playing Russian roulette. In 5 years went through over half a dozen cables.
USB C is much more reliable, rugged... and dumb bunny proof.
dladz said:
27 minute's?
Click to expand...
Click to collapse
Yes, with the phone OFF.
blackhawk said:
C ports can be quit durable* if kept clean (rarely need cleaning). They typically last many years and thousands of charge cycles. You'll likely replace 2 or more batteries before a C port.
Typically the C port is easier to replace than the battery. A heavily used device's battery will last 1 to 2 years at best.
Direct charging is faster and generates less heat. High temperature and cell voltage are an Li's prime premature degraders.
*at least on a Samsung N10+
Click to expand...
Click to collapse
Not all of them.
I bought for my sister Nokia 7 Plus few years back. Usb_C get broken. She use it for charging and copy to/from PC..
To replace the port they need to remove the screen (with heat & bla bla). It could Not be changed thruu the back cover. It cost almost 30 euro, which is a lot for a usb port.
You can clean the port with a sharp wooden toothpick with some contact spray or isopropyl alcohol.
dladz said:
I've seen someone buy a phone, I was working in a phone repair shop and she bought the really expensive Sony phone. She was quite rough with it, shoved the micro usb cable into it the wrong way several times, broke off most the pins, literally list 1200 quid on the spot.
I think that's partly why usb c became a thing, so much more reliable, it's design I'm referring to. I know power delivery was it's driving force and data rate.
Click to expand...
Click to collapse
Is funny how stupid people buy expensive things...
null0seven said:
Yes, with the phone OFF.
Click to expand...
Click to collapse
If that's true buddy, that's a hell of a trick I just didn't bother with for some reason. If that's the case then I'd imagine the 10 pro will top up faster than a car a petrol station.
I'd great find but I feel like a tit for not noticing it myself
null0seven said:
Yes, with the phone OFF.
Not all of them.
I bought for my sister Nokia 7 Plus few years back. Usb_C get broken. She use it for charging and copy to/from PC..
To replace the port they need to remove the screen (with heat & bla bla). It could Not be changed thruu the back cover. It cost almost 30 euro, which is a lot for a usb port.
You can clean the port with a sharp wooden toothpick with some contact spray or isopropyl alcohol.
Click to expand...
Click to collapse
C port quality depends on the manufacturer and perhaps model
A toothpick could deform contacts, a soft stiff bristle seems more appropriate... with care.
3% hydrogen peroxide can be used as it will get under the lint and react with it, dislodging it.
Dry throughly.
It makes sense that charging is faster with the phone off.
null0seven said:
It makes sense that charging is faster with the phone off.
Click to expand...
Click to collapse
Yes thank you Mr Hawkin