[S] HTC One M7 Semi Bricked Force AC Problem - One (M7) Q&A, Help & Troubleshooting

So I think I may have hard (or Soft) bricked my HTC one, I recently installed faux123's sense kernel: m7-faux123-GE444-016u and was experiencing several crashes and problems so I re flashed the elementalx kernel (A past WORKING configuration) following all the same steps I normally do when installing a new kernel (clearing cache and my devlick [Not sure how to spell it])
After re flashing I was experiencing boot issues where my phone wouldn't make it past the "HTC" Splash screen, so I tried several times re flashing ElementalX with different settings, after several tries i decided to restore from a recently made backup of my ROM, which gave me the same results as installing the ElementalX kernel... no ability to boot. Then out of frustration I decided to reformat my entire /sdcard thinking I could re flash my roms and kernels via usb and my laptop... until I went into fast boot... turns out I have ac mode locked (A kernel setting I set awhile back when experimenting) so now my phone is stuck in clockwork mod recovery and I'm unable to make any changes via ADB commands or Fast Boot.
So basically what I'm asking is if my phone is completely screwed over, and if there is any way of removing the AC Charging lock, without flashing a new kernel or booting (Since I did a full SD wipe, all my backups and roms, and kernels are gone) and if I will have to send my phone in to get it repaired
UPDATE: so I noticed some basic functions of the phone work, pressing the volume up and down keys eventually cause the phone to viberate, as if the phone is vibrating when it goes into silent mode, the backlight turns on and off when the power button is pressed quickly, what is going on, any ideas?? is the phone running properly and i just cant see it??
Final Update: So I got Everything working and I am now able to flash a new rom and everything on my phone... the way it was fixed was by use of the OTG cable, After leaving my phone running a little while The usb Mounted with absolutely no trouble I used the reccommended roms and it installed with no issues, now that I have a running backup I am now going to install the roms I used before all the issues arose, thank you for all your help!! you guys saved me a trip to a repair center, and also spending for a new phone Cheers!

Jromkes1 said:
So I think I may have hard (or Soft) bricked my HTC one, I recently installed faux123's sense kernel: m7-faux123-GE444-016u and was experiencing several crashes and problems so I re flashed the elementalx kernel (A past WORKING configuration) following all the same steps I normally do when installing a new kernel (clearing cache and my devlick [Not sure how to spell it])
After re flashing I was experiencing boot issues where my phone wouldn't make it past the "HTC" Splash screen, so I tried several times re flashing ElementalX with different settings, after several tries i decided to restore from a recently made backup of my ROM, which gave me the same results as installing the ElementalX kernel... no ability to boot. Then out of frustration I decided to reformat my entire /sdcard thinking I could re flash my roms and kernels via usb and my laptop... until I went into fast boot... turns out I have ac mode locked (A kernel setting I set awhile back when experimenting) so now my phone is stuck in clockwork mod recovery and I'm unable to make any changes via ADB commands or Fast Boot.
So basically what I'm asking is if my phone is completely screwed over, and if there is any way of removing the AC Charging lock, without flashing a new kernel or booting (Since I did a full SD wipe, all my backups and roms, and kernels are gone) and if I will have to send my phone in to get it repaired
Click to expand...
Click to collapse
ummm lol oops, can you post your fastboot getvar all please, is that even possible ? then we can see if we can find an RUU for you to run through your phone.
EDIT, just saw you cant make any changes via fastboot or adb, my bad, my first question to you is why would you enable an option like that ?, I could suggest you get a USB OTG cable and stick a custom rom on it then plug it into the phone and from recovery flash it, problem is, most custom roms require twrp recovery and you have cwm.
you could send your phone in for repair, but im guessing your bootloader is unlocked and unfortunately, this voids warranty and you'll have to pay for any repairs.

Seanie280672 said:
ummm lol oops, can you post your fastboot getvar all please, is that even possible ? then we can see if we can find an RUU for you to run through your phone.
EDIT, just saw you cant make any changes via fastboot or adb, my bad, my first question to you is why would you enable an option like that ?, I could suggest you get a USB OTG cable and stick a custom rom on it then plug it into the phone and from recovery flash it, problem is, most custom roms require twrp recovery and you have cwm.
you could send your phone in for repair, but im guessing your bootloader is unlocked and unfortunately, this voids warranty and you'll have to pay for any repairs.
Click to expand...
Click to collapse
Thanks for your response! (im a newbie, as you probably already know)
about the Force AC issue: I foolishly enabled it when i was customizing my kernel not knowing that it would give me this much trouble, and the effects it'd give.
if I got a OTG cable would that work? or would it go into AC mode? What if i got the sense venom rom and installed it on CWM? that's what I used before and it worked quite well. i am going to town now to buy a OTG cable ill be back and ill let you know how it goes, I think this may work... Finally a slight gleam of hope for my HTC One

Jromkes1 said:
Thanks for your response! (im a newbie, as you probably already know)
about the Force AC issue: I foolishly enabled it when i was customizing my kernel not knowing that it would give me this much trouble, and the effects it'd give.
if I got a OTG cable would that work? or would it go into AC mode? What if i got the sense venom rom and installed it on CWM? that's what I used before and it worked quite well. i am going to town now to buy a OTG cable ill be back and ill let you know how it goes, I think this may work... Finally a slight gleam of hope for my HTC One
Click to expand...
Click to collapse
that rom will just bootloop, it requires twrp recovery.
you could try and put CM11 on a usb stick, plug the usb stick into one end of the OTG cable (on the go cable) and the other into your phone, boot into cwm and then select install from OTG, I think CM roms require CWM, cant promise anything, but worth a try.
normally you would beable to put stock rom.zip on the otg cable and flash that, but it requires a locked or re-locked bootloader, and that's not going to be possible without a fastboot command.
another option that springs to mind, is put the kernel you originally flashed on the OTG cable, install it in CWM, im guessing the option to enable force AC was enabled during install ? just disable it and continue with the kernel flash, after a reboot you may get fastboot USB, easy to fix once you get that.

Jromkes1 said:
So I think I may have hard (or Soft) bricked my HTC one, I recently installed faux123's sense kernel: m7-faux123-GE444-016u and was experiencing several crashes and problems so I re flashed the elementalx kernel (A past WORKING configuration) following all the same steps I normally do when installing a new kernel (clearing cache and my devlick [Not sure how to spell it])
After re flashing I was experiencing boot issues where my phone wouldn't make it past the "HTC" Splash screen, so I tried several times re flashing ElementalX with different settings, after several tries i decided to restore from a recently made backup of my ROM, which gave me the same results as installing the ElementalX kernel... no ability to boot. Then out of frustration I decided to reformat my entire /sdcard thinking I could re flash my roms and kernels via usb and my laptop... until I went into fast boot... turns out I have ac mode locked (A kernel setting I set awhile back when experimenting) so now my phone is stuck in clockwork mod recovery and I'm unable to make any changes via ADB commands or Fast Boot.
So basically what I'm asking is if my phone is completely screwed over, and if there is any way of removing the AC Charging lock, without flashing a new kernel or booting (Since I did a full SD wipe, all my backups and roms, and kernels are gone) and if I will have to send my phone in to get it repaired
Click to expand...
Click to collapse
I second the idea of the USB OTG, I use mine all the time.
this Older version of ARHD should work fine with cwm
http://www.androidrevolution.org/downloader/download.php?file=Android_Revolution_HD-One_31.6.zip

clsA said:
I second the idea of the USB OTG, I use mine all the time.
this Older version of ARHD should work fine with cwm
http://www.androidrevolution.org/downloader/download.php?file=Android_Revolution_HD-One_31.6.zip
Click to expand...
Click to collapse
I use mine all the time too, mainly for backup's though, I have a 8gb USB stick pretty much full of backup's

OK So i got an OTG cable and now I am preparing to download the required roms and everything onto the USB, the only question i have is if the usb will work with the current (AC only) power settings, or will it not work? *Sigh* this is so frusterating
EDIT: soo... the OTG cable does not work from what it appears, I just cannot figure out a way to mount it with CWM, any ideas?

Jromkes1 said:
OK So i got an OTG cable and now I am preparing to download the required roms and everything onto the USB, the only question i have is if the usb will work with the current (AC only) power settings, or will it not work? *Sigh* this is so frusterating
Click to expand...
Click to collapse
only one way to find out, with the phone in the bootloader, plug in the USB OTG cable now and see if it turns to fastboot host ?
if not, don't worry just yet, you'll still need to see if it works in recovery or not.
---------- Post added at 09:54 PM ---------- Previous post was at 09:53 PM ----------
Jromkes1 said:
OK So i got an OTG cable and now I am preparing to download the required roms and everything onto the USB, the only question i have is if the usb will work with the current (AC only) power settings, or will it not work? *Sigh* this is so frusterating
EDIT: soo... the OTG cable does not work from what it appears, I just cannot figure out a way to mount it with CWM, any ideas?
Click to expand...
Click to collapse
when you select install, does it not give you an option to choose between internal storage and USB OTG ?

Seanie280672 said:
only one way to find out, with the phone in the bootloader, plug in the USB OTG cable now and see if it turns to fastboot host ?
if not, don't worry just yet, you'll still need to see if it works in recovery or not.
---------- Post added at 09:54 PM ---------- Previous post was at 09:53 PM ----------
when you select install, does it not give you an option to choose between internal storage and USB OTG ?
Click to expand...
Click to collapse
no it does not, i went to advanced > mounts and storage > Mount USB Storage and nothing happens aswell
EDIT: Fastboot does not turn into fastboot Host either

Jromkes1 said:
no it does not, i went to advanced > mounts and storage > Mount USB Storage and nothing happens aswell
Click to expand...
Click to collapse
unfortunately I think its lost, theres only a couple more things you could possibly try, one is to riffbox it, you should beable to get this done at a little back street mobile phone shop or although its not a hard brick, you could try this, not sure if it will work on your device, but if it does it will re-write your partitions.
http://forum.xda-developers.com/showthread.php?t=2770684
this is the first soft brick.......ummm.......hard brick HTC M7 ive seen.

Seanie280672 said:
unfortunately I think its lost, theres only a couple more things you could possibly try, one is to riffbox it, you should beable to get this done at a little back street mobile phone shop or although its not a hard brick, you could try this, not sure if it will work on your device, but if it does it will re-write your partitions.
http://forum.xda-developers.com/showthread.php?t=2770684
this is the first soft brick.......ummm.......hard brick HTC M7 ive seen.
Click to expand...
Click to collapse
ok, the only problem is that it requires a usb connection, and that's my problem, it changes to AC power when it gets plugged into any powered device via usb... see I know i could fix my problem if it were not for the damn kernel settings I made a long while ago, like It still works, I just can't access the internal SD card

Jromkes1 said:
no it does not, i went to advanced > mounts and storage > Mount USB Storage and nothing happens aswell
EDIT: Fastboot does not turn into fastboot Host either
Click to expand...
Click to collapse
maybe this will help
https://www.youtube.com/watch?v=ZLISkavPg9U
---------- Post added at 05:20 PM ---------- Previous post was at 05:16 PM ----------
Seanie280672 said:
I use mine all the time too, mainly for backup's though, I have a 8gb USB stick pretty much full of backup's
Click to expand...
Click to collapse
I have a couple of these their really handy
http://www.kingston.com/us/usb/pers...SB-OTG&gclid=CISjr6HI_78CFSxk7AodwFEABQ#DTDUO

clsA said:
maybe this will help
https://www.youtube.com/watch?v=ZLISkavPg9U
---------- Post added at 05:20 PM ---------- Previous post was at 05:16 PM ----------
I have a couple of these their really handy
http://www.kingston.com/us/usb/pers...SB-OTG&gclid=CISjr6HI_78CFSxk7AodwFEABQ#DTDUO
Click to expand...
Click to collapse
sadly I was just watching the same video, I have no options to open the OTG external sd cards, anywhere, I am genuinely mystified by this

Jromkes1 said:
sadly I was just watching the same video, I have no options to open the OTG external sd cards, anywhere, I am genuinely mystified by this
Click to expand...
Click to collapse
not OTG just install / external sdcard
reformat the flash drive your using to fat32 copy the rom to it and try again

clsA said:
not OTG just install / external sdcard
reformat the flash drive your using to fat32 copy the rom to it and try again
Click to expand...
Click to collapse
still nothing... but i did find something interesting, when it reboots and it passes the HTC splash screen the screen goes black like it should, but the USB light turns on and it flashes like its supposed to (No Light when in recovery), and also the power buttons turns on and off the backlight, and the volume buttons turns seems to make the mute single vibration when it is pressed down enough times. very strange
edit: when doing the unlocking gesture it seems my phone is working! volume presses makes the default beep, holding power buttons makes a quick vibration like when the power menu appears... do you think my phone IS working its just the kernel that is messed up? and is not allowing my screen to function correctly?

Related

Reboots when Usb connected

Flashed today my GT-I9000 to TO froyo I897UCJI6. I know i should not have done that now. But i really got pissed today at the gps of my phone and when i saw and update for galaxy s i just went for it, haven't checked the phone variant version. Thing is now my phone has no gps whatsoever it boots up fine but, sound only shows when i plug my headphones, accelerometer dont work correctly and so on....
So i though i`ll flash it back to stock. But the thing is once i connect the usb cable the phone just reboots and stays dead until the usb is disconnected.
I read the other threads but found no similar issues.
Here is a brief video of my problem
-http-://-www-.youtube.-com/-watch?v=MtcCvfCbAFk-
Remove all "-"
since i can`t post links
Anyone has any ideas how to get me back to stock?
Thanks!!
Damn i can`t even charge it!
Kinda weird indeed, try to remove the battery, wait a little, insert the battery and go to download mode (volume - / home / power) then start odin, put all files needed, and connect the usb, if it doesnt reboot hit start...
you got to enable adb debugging on your phone then open a command window and type: adb reboot download connect the usb to the phone and hit the enter key for the adb command before your phone fall asleep, then you are in download mode an can flash any rom with odin.
hope this helps, i flashed the same wrong firmware from the Vibrant.
Thanks Franklin, i tried the battery trick to no luck.
This is i cannot put my phone back to download mode because my "HOME" button is not mapped to do anything, seems like the "RETURN ARROW" button does the fuction when the system is loaded.
Any other ways to flash it back? Sd card or something?
Thanks for replies ;]
please try it my way it worked for me and i think it will work for you
I open the cmd navigate to c:\androidsdk\tools\ type in adb reboot download hit enter, it mounts daemon tools i plug in usb cable and 3 seconds later the phone goes blank and it stays unresponsive(no 3 key combination, not even the power button can turn it back on) i unplug the usb cable and the phone automaticaly shows the AT&T logo and starts up. The same happens when i plug my charger in!. Does that mean my SGS usb port is fried or something? Is there another way to flash my pnoe back to stock ROM?
I am so sorry i tried to make it better :[
Any clues?
no this is NOT a defective phone, its the result of the ROM and the 3 Button combo can´t work oh and you dont really mean deamon tools? and you musst plug the usb cable in the phone right before you hit enter or it can´t work!
I did that too. Like i said the phone turns it self off once the usb cable is attached.
Here is a brief video of my problem
-http-://-www-.youtube.-com/-watch?v=MtcCvfCbAFk-
remove all "-" from url.
dainiuxxx, this thread belongs in the Q&A section, not in development. Take a moment and read the "STOP, READ THIS BEFORE POSTING" thread at the top of both of these sections, it has clear guidelines for proper thread placement.
Sorry for that sirphukee.
Any help? Anyone?
Anyone that can help?
have you tried plugging it into another PC or Laptop?
Yup tried amothe laptop, reboot.
Wall charger, reboot.
So i`m kinda out of options?
yes, return it to the store, to get an exchange
a normal working SGS does not reboot when plugged into any USB port/charger
it's Shorted (damaged) for some reason
ok, return sounds good to me, but what will i have to say when they`ll switch on the phone and see the AT&T logo?
I`m in UK and my network is Orange UK.
Will they accept it back with no problems, i kinda doubt that....
uhh... you are in quite a pickle ...
try to remove the evidence, intentionally use a Update.zip ROM flash to kill the flash
or flash it to stock if you find a good ROM via Update.zip
use the WiFi to download the Update.zip ROM flash to the root of the internal SD to flash it.
ROM Manager can get the same results, you can WiFi install it from Market
AllGamer said:
uhh... you are in quite a pickle ...
try to remove the evidence, intentionally use a Update.zip ROM flash to kill the flash
or flash it to stock if you find a good ROM via Update.zip
use the WiFi to download the Update.zip ROM flash to the root of the internal SD to flash it.
ROM Manager can get the same results, you can WiFi install it from Market
Click to expand...
Click to collapse
Installed ROM manager from market, but seems it needs the phone rooted, right?
And rooting can be done only via usb cable, right?
Where do i find a Update.zip ROM via Wifi? and what are the procedures when i do find it?
OK,
so obviously the question now is HOW DO I F...k up my phone completely so no one could see what was done to it. When i`ll take it back to the shop.
dainiuxxx said:
Installed ROM manager from market, but seems it needs the phone rooted, right?
And rooting can be done only via usb cable, right?
Where do i find a Update.zip ROM via Wifi? and what are the procedures when i do find it?
Click to expand...
Click to collapse
you can ROOT the phone within the phone itself
by downloading Ryzaa One click lag fix from the market
instead of installing the lag fix, select the option to ROOT the phone
Same issue here. Amazing how easy it is to mess this phone up when you are really stupid. Oh well....
Tried the one click lag fix to root it, but cannot find a way to get into download or recovery mode. Tried every button combo I have seen suggested, but either gets stuck in a loop on the AT&T screen or just boots into the OS.
At the moment I feel my only option if we cannot find a way to get into download mode is to format the internal SD card and send it back to o2 (my provider), tell them it fried when Kies tried to do an update, cross my fingers and hope they send me a new one.

[Q] Weird problem

Running rooted stock KJ3 with Samurai Kernel 1.0
I have no idea what caused this but all of a sudden the ONLY way I can get into download mode is with a jig, no button combos work, the volume buttons with usb plug doesn't work (only turns the phone on). And weirder still if the phone is off, plugging in the charger turns the phone on.
Anybody know what caused this?
Should I reflash bootloaders?
Any ideas would be appreciated...
im having about the same problem right now but the bigger issue with me is that my computer doesn't recognise the phone it keeps saying unknown usb device. im converting back to rfs now to change roms back to ki2 and see if it is still doing it. ill report back if i can find anything out.
---------- Post added at 07:28 AM ---------- Previous post was at 06:46 AM ----------
well i cwm back to ki2 and im still having that problem but i really think that im having usb issues with the phone. the phone doesn't recognise when i plug the usb from the computer it only thinks it is charging.
1. horrible tread title, next time give some clue as to what your problem is IN the title.
2.do the recovery button combos work? reflashing the boots may work just remember as with all flashes that include bootloaders there is a risk of hard bricking the phone if something goes awry.
kschumake83: go to settings> application>>usb settings and toggle mass storage (if its on it already switch to something else and switch back.) then go to development thats right above usb settings and retoggle usb bedugging back on.
you also may have a driver issue and a reinstall of them might help.
and finally, i oncwe ran over my usb cable with my office chair, it would still charge but the data connection was broken and could only be used to charge. so it might be your cable.
studacris said:
1. horrible tread title, next time give some clue as to what your problem is IN the title.
2.do the recovery button combos work? reflashing the boots may work just remember as with all flashes that include bootloaders there is a risk of hard bricking the phone if something goes awry.
kschumake83: go to settings> application>>usb settings and toggle mass storage (if its on it already switch to something else and switch back.) then go to development thats right above usb settings and retoggle usb bedugging back on.
you also may have a driver issue and a reinstall of them might help.
and finally, i oncwe ran over my usb cable with my office chair, it would still charge but the data connection was broken and could only be used to charge. so it might be your cable.
Click to expand...
Click to collapse
1) bedugging???
2) If it is a bad cable, DO NOT try to flash bootloaders.
Oic we're doing the typo dance this morning lol.
But right the bootloader reflash advice was directed just at the op, because yeah bad cable + bootloader flash = very bad day.
Yeah, end up sending phone out for Unbrickable Mod or JTAG.
My apologies for the horrible "tread" title ;-)
recovery button combo does work...
I also have problems with computer or Odin recognizing the phone. I reinstalled drivers (no change), then I tried reinstalling kies and it would recognize phone and work through one Odin flash but not through a second...so the process becomes: reinstall kies, flash rom, reinstall kies, flash custom kernel...
Any ideas?
studacris said:
1. horrible tread title, next time give some clue as to what your problem is IN the title.
2.do the recovery button combos work? reflashing the boots may work just remember as with all flashes that include bootloaders there is a risk of hard bricking the phone if something goes awry.
kschumake83: go to settings> application>>usb settings and toggle mass storage (if its on it already switch to something else and switch back.) then go to development thats right above usb settings and retoggle usb bedugging back on.
you also may have a driver issue and a reinstall of them might help.
and finally, i oncwe ran over my usb cable with my office chair, it would still charge but the data connection was broken and could only be used to charge. so it might be your cable.
Click to expand...
Click to collapse
Im almost positive its my port on my phone because my wifes captivated connects perfectly and i tried toggleing the usb settings too.
Sent from my SAMSUNG-SGH-I897 using xda premium
Are you on captivate bootloaders?
Edit.. I assume you are because you said stock kj3.. Perhaps you have a short inside the usb slot on your phone.. Maybe take a look in there and see if there is any debris
Sent from my SAMSUNG-SGH-I897 using XDA Premium App

HTC Vivid Bricked?

Hi,
I have a 1 month old HTC Vivid. It was running it on ICS 4.0.3 and it was rooted. Today, while I was working on it, it suddenly powered off and now it won't do anything. Like it doesn't display anything on the screen, doesn't get powered up and when I connect the charger, I can't even see the orange light. ITS TOTALLY F**KED UP!!!
Please Help!! Thanks!!
Can you boot into H-Boot?
Sent from my HTC PH39100 using XDA
I got the same problem. The phone did not work at all. It only flashed for a few seconds when I pressed the power button. I searched all the websites, but nothing worked. My solution is to send the phone to HTC to have it fix. They have a very good customer service.
With the charger plugged in, does the phone vibrate when the HOME, MENU, BACK, or SEARCH buttons are pressed?
Had a similar problem, for me HTC was the only solution, just say that it happened suddenly and dont mention anything about boot loader or roms.
Have you guys tried project UNBRICK yet? Search that on the forum here, as I can't post links yet.
jul644 said:
Had a similar problem, for me HTC was the only solution, just say that it happened suddenly and dont mention anything about boot loader or roms.
Click to expand...
Click to collapse
This. AT&T replaced my no-power Vivid under the One Year Warranty.
BTJustice said:
With the charger plugged in, does the phone vibrate when the HOME, MENU, BACK, or SEARCH buttons are pressed?
Click to expand...
Click to collapse
mine does. do you know how to fix it.
rhino474 said:
mine does. do you know how to fix it.
Click to expand...
Click to collapse
Yes but it is a pain and takes several tries. I had this problem a few days ago and this was the only way I could get around it.
I HOPE YOU HAVE DATA BACKED UP! That's your responsibility and not mine. If this ruins your phone then tough. I will not be held responsible for a bricked phone...
First off, assuming the bootloader is UNLOCKED, install the ALL IN ONE tool on your computer (it actually runs from a folder and doesn't really install which is good)...
http://forum.xda-developers.com/showthread.php?t=1498003
Open it, then...
Remove any bought protective case (it may mess with the buttons).
Unplug charger.
Remove battery.
Wait 5 minutes.
Reinstall battery.
Plug in USB cable from the computer.
Hold down the VOLUME DOWN button and then the POWER button.
It should boot into the bootloader. On the ALL IN ONE tool, flash recovery to CWM. Once complete, click on "Boot into Recovery".
If the phone does not boot into Recovery, flash recovery to WCX.
If the phone reboots into Recovery, you will want to do a factory reset, wipe cache, go to mounts and format them all. Then mount it as USB and copy/paste a ROM over and flash to that ROM. I like Virtuous Inquisition v4.0.2.1.
Good luck.
BTJustice said:
Yes but it is a pain and takes several tries. I had this problem a few days ago and this was the only way I could get around it.
I HOPE YOU HAVE DATA BACKED UP! That's your responsibility and not mine. If this ruins your phone then tough. I will not be held responsible for a bricked phone...
First off, assuming the bootloader is UNLOCKED, install the ALL IN ONE tool on your computer (it actually runs from a folder and doesn't really install which is good)...
http://forum.xda-developers.com/showthread.php?t=1498003
Open it, then...
Remove any bought protective case (it may mess with the buttons).
Unplug charger.
Remove battery.
Wait 5 minutes.
Reinstall battery.
Plug in USB cable from the computer.
Hold down the VOLUME DOWN button and then the POWER button.
It should boot into the bootloader. On the ALL IN ONE tool, flash recovery to CWM. Once complete, click on "Boot into Recovery".
If the phone does not boot into Recovery, flash recovery to WCX.
If the phone reboots into Recovery, you will want to do a factory reset, wipe cache, go to mounts and format them all. Then mount it as USB and copy/paste a ROM over and flash to that ROM. I like Virtuous Inquisition v4.0.2.1.
Good luck.
Click to expand...
Click to collapse
it didnt work, but thanks for trying.
---------- Post added at 05:17 AM ---------- Previous post was at 05:06 AM ----------
rhino474 said:
it didnt work, but thanks for trying.
Click to expand...
Click to collapse
Never mind, I got it working. Thanks.
rhino474 said:
it didnt work, but thanks for trying.
---------- Post added at 05:17 AM ---------- Previous post was at 05:06 AM ----------
Never mind, I got it working. Thanks.
Click to expand...
Click to collapse
What did you wind up doing to get it to work? Be descriptive.
I too had my vivid bricked but i use Toolkit to solve the issue.:victory:
BTJustice said:
Yes but it is a pain and takes several tries. I had this problem a few days ago and this was the only way I could get around it.
I HOPE YOU HAVE DATA BACKED UP! That's your responsibility and not mine. If this ruins your phone then tough. I will not be held responsible for a bricked phone...
First off, assuming the bootloader is UNLOCKED, install the ALL IN ONE tool on your computer (it actually runs from a folder and doesn't really install which is good)...
http://forum.xda-developers.com/showthread.php?t=1498003
Open it, then...
Remove any bought protective case (it may mess with the buttons).
Unplug charger.
Remove battery.
Wait 5 minutes.
Reinstall battery.
Plug in USB cable from the computer.
Hold down the VOLUME DOWN button and then the POWER button.
It should boot into the bootloader. On the ALL IN ONE tool, flash recovery to CWM. Once complete, click on "Boot into Recovery".
If the phone does not boot into Recovery, flash recovery to WCX.
If the phone reboots into Recovery, you will want to do a factory reset, wipe cache, go to mounts and format them all. Then mount it as USB and copy/paste a ROM over and flash to that ROM. I like Virtuous Inquisition v4.0.2.1.
Good luck.
Click to expand...
Click to collapse
Worked perfect - had to pull the kernel out of the ROM I used and flash it with the tool but it worked perfectly...
Im betting your screen might be toast, happened to my wife's vivid, completely just up and died one day for no reason. I haven't rooted yet and this sort of stuff makes me leary to do it.
Sent from my VTC HIVID using the xda app
http://forum.xda-developers.com/showthread.php?t=1717766
http://forum.xda-developers.com/showthread.php?t=1479060
http://forum.xda-developers.com/showthread.php?t=1531208
http://forum.xda-developers.com/showthread.php?t=1694017
http://forum.xda-developers.com/showthread.php?t=1769616
http://forum.xda-developers.com/showthread.php?t=1652689
http://forum.xda-developers.com/showthread.php?t=1732268
http://forum.xda-developers.com/showthread.php?t=1754534
EDIT: I have stopped looking for these threads. The more I look, the more I find. If the above threads don't convince you that there is a serious issue with the vivid, then adding more of the same problem will no longer help.
I have added this thread to a growing list of similar threads. Please read the other threads and see if your issues seem familiar.
From what I understand... Don't let your battery run out on this phone. Some Vivids kill batteries.
Solution? None yet.
1. Buy a new battery once a couple of months-ish, until someone figures out why some Vivids are eating batteries. YMMV
*OR*
2. You might invest in a external charger and see if that can bring the "Vivid munched" battery back to life. YMMV
I vote to thread merge the above threads if this proves to be the issue.

[Q] Another way to boot to Recovery?

Hi everyone,
I started to use custom roms about some months ago, and I'm facing my biggest problem right now, hope someone can help me.
I flashed my phone via TWRP Custom recovery with CM10.1 and one day, suddenly the pin (that little entering for the charger and usb cables) stopped working, so I couldn't charge my phone in any "normal" way, I started using a direct battery charger. But today I flashed my phone with another version of CM and forgot to wipe data/cache, so now it's stucked in the CM boot animation. Thing is, I can't even access to recovery mode to flash again because for some reason, everytime I turn my phone off, it turns on automatically. Without pressing any button, and it doesn't give me time to do the vol-/home/power combo. I can't use any direct cable alternative either for what I described above. So I was wondering if some of you had a similar problem and can give me a hand with this. I'd be very much appreciated it.
Many thanks and greetings from Perú!
unotresocho.
unotresocho said:
Hi everyone,
I started to use custom roms about some months ago, and I'm facing my biggest problem right now, hope someone can help me.
I flashed my phone via TWRP Custom recovery with CM10.1 and one day, suddenly the pin (that little entering for the charger and usb cables) stopped working, so I couldn't charge my phone in any "normal" way, I started using a direct battery charger. But today I flashed my phone with another version of CM and forgot to wipe data/cache, so now it's stucked in the CM boot animation. Thing is, I can't even access to recovery mode to flash again because for some reason, everytime I turn my phone off, it turns on automatically. Without pressing any button, and it doesn't give me time to do the vol-/home/power combo. I can't use any direct cable alternative either for what I described above. So I was wondering if some of you had a similar problem and can give me a hand with this. I'd be very much appreciated it.
Many thanks and greetings from Perú!
unotresocho.
Click to expand...
Click to collapse
Press recovery combos when your turning off, see if that works, you might just be holding power too long and it turns on again
No usb at all? If you can connect with adb, you can reboot to recovery that way.
Combo.
unotresocho said:
Hi everyone,
I started to use custom roms about some months ago, and I'm facing my biggest problem right now, hope someone can help me.
I flashed my phone via TWRP Custom recovery with CM10.1 and one day, suddenly the pin (that little entering for the charger and usb cables) stopped working, so I couldn't charge my phone in any "normal" way, I started using a direct battery charger. But today I flashed my phone with another version of CM and forgot to wipe data/cache, so now it's stucked in the CM boot animation. Thing is, I can't even access to recovery mode to flash again because for some reason, everytime I turn my phone off, it turns on automatically. Without pressing any button, and it doesn't give me time to do the vol-/home/power combo. I can't use any direct cable alternative either for what I described above. So I was wondering if some of you had a similar problem and can give me a hand with this. I'd be very much appreciated it.
Many thanks and greetings from Perú!
unotresocho.
Click to expand...
Click to collapse
Use key combos mate... and after the phone vibrates, release only power button for avoiding the autorestart :fingers-crossed:
Hi, thanks all for your advices. I try em all but with no sucess. Though, something weird happened today. After the battery completely drained I tried charging it with the my regular charger, the cable to the wall one, and the phone vibrated, like it recognized it, but didn't turn on. Just vibrated. So I tried again using my micro USB to PC cable and the phone vibrated again when I plugged in to the USB port, but didn't turn on either, nor the PC recognized the device. Don't know if this is good or bad :S
If you have any more ideas, please let me know.
Thanks!
Unotresocho.
AlexGardunio said:
Use key combos mate... and after the phone vibrates, release only power button for avoiding the autorestart :fingers-crossed:
Click to expand...
Click to collapse
I'm trying this, but it keeps auto restarting. I'll describe what I'm doing, maybe there's something wrong:
1. Insert the battery.
2. Phone vibrates, I press Vol-/Home/Power and Samsung Galaxy S3 mini shows.
3. Keep pressing the combo and the phone turns off
4. Release the power button
5. Phone vibrates and again shows the Samsung logo and then the CM boot animation
Turn off again and same.
Thanks for the advice!
Hi again, I managed to get to "Odin Mode", the recovery that comes by default with the phone. Don't know why if I had TWRP installed. Does anyone know if it's gonna help me in some way? Remember I can't use a cable
Thanks!
How did you get into "Odin Mode"? Are you sure the cable is not working when the phone is in download mode?
Got into it by doing the button combo, tried several times and it was tricky but finally got it. And yeah I quickly connected to the computer (I have a Macbook but I also try on a PC) neither of them recognized it. Don't know what else to do
Try wireless adb.
When connected to computer:
Code:
adb shell
su
reboot recovery
As far as I know the phone should not vibrate everytime you put battery back. But if you're able to go into odin you should be able to go into recovery (unless volume up key is damaged). But... while in odin... you can go back to stock rom and that should solve lots of your problems mate.
tys0n said:
Try wireless adb.
When connected to computer:
Code:
adb shell
su
reboot recovery
Click to expand...
Click to collapse
Hi tys0n, thanks for your suggestion. I did a little research and found that to connect the phone on adb wirelessly I'd need a previously installed app. Do you know any other way to get it?
Many thanks!
unotresocho said:
I did a little research and found that to connect the phone on adb wirelessly I'd need a previously installed app.
Click to expand...
Click to collapse
You also need a working rom.
If the usb connector on the phone is broken, you can buy another one for 4$ on ebay, but you'll need to solder it and it's a smd component with small pins, so it may be difficult.
You can also try to reboot your phone in safe mode:
http://skp.samsungcsportal.com/integrated/popup/FaqDetailPopup3.jsp?cdsite=uk&seq=898277
http://androidjinn.com/boot-android-4-1-safe-mode.html
deconectat said:
You also need a working rom.
If the usb connector on the phone is broken, you can buy another one for 4$ on ebay, but you'll need to solder it and it's a smd component with small pins, so it may be difficult.
You can also try to reboot your phone in safe mode:
http://skp.samsungcsportal.com/integrated/popup/FaqDetailPopup3.jsp?cdsite=uk&seq=898277
http://androidjinn.com/boot-android-4-1-safe-mode.html
Click to expand...
Click to collapse
Yeah, thats true. A working system is needed.
Just a question.. When you try to enter recovery (vol+/home/power), have you tried to keep pushing when it reboots?
Have you tried to connect usb in download mode (vol-/home/power) to see if Odin detects it?
Whiteout a being able to synch to your computer or accessing recovery mode youre not gonna be able to restore your phone. Your best bet is buying a new micro usb cable (they are inexpensive) and restore using Odin.
tys0n said:
Yeah, thats true. A working system is needed.
Just a question.. When you try to enter recovery (vol+/home/power), have you tried to keep pushing when it reboots?
Have you tried to connect usb in download mode (vol-/home/power) to see if Odin detects it?
Click to expand...
Click to collapse
Yeah, I keep pushing the buttons combo and it reboots again, it won't start to boot CM, just displays de Samsung logo and reboots. About the second question, I've tried connecting the computer while in Odin mode but it won't recognize it, I haven't tried with Odin itself open because my primary computer is a Macbook and don't have a PC with the Odin installed near to me all the time. Do you think it could recognize the device, despite the fact the whole PC doesnt?
Thanks!
Arrrroz said:
Whiteout a being able to synch to your computer or accessing recovery mode youre not gonna be able to restore your phone. Your best bet is buying a new micro usb cable (they are inexpensive) and restore using Odin.
Click to expand...
Click to collapse
Hi, I wish it'd be that easy! The problem is the pin entrance in the phone, not the cable. I have like 4 with me, but none of them works
unotresocho said:
Hi, I wish it'd be that easy! The problem is the pin entrance in the phone, not the cable. I have like 4 with me, but none of them works
Click to expand...
Click to collapse
Oh, I see. You mention you could access odin mode, Im not familiar with it, but maybe it is possible that you could flash TWRP again, or CWR from the odin recovery? Also if you don't mind me asking, do you know how did the phone's pin got damaged?
I'm starting to thing you aint got a recovery at the moment. I've seen this type of thing before. Problem is, if you can't get odin to work you won't be able to solve it :/
Arrrroz said:
Oh, I see. You mention you could access odin mode, Im not familiar with it, but maybe it is possible that you could flash TWRP again, or CWR from the odin recovery? Also if you don't mind me asking, do you know how did the phone's pin got damaged?
Click to expand...
Click to collapse
I have no idea. I didn't fall or anything, it just stopped working one day. I thought it had to do with a "software" thing more than hardware, because I was using CM 10.1 and of course it wasn't official, it had bugs. I actually was trying to go back to CM10 to see if that was the problem but I got stuck here.

[Q] Need to backup files from i9000 with no display`

Hi all, I have an i9000 with a broken screen and digitiser. I need to recover the data from it (pictures mainly). There is no display at all but the phone is working otherwise - I can hear it booting up and I can put it into Download and Recovery modes.
Unfortunately it's running the stock firmware so I can't use Recovery Mode to mount USB storage. When turned on normally, it will connect to my PC but obviously I can't press the button to mount storage (why doesn't it mount automatically???).
Does anyone have any ideas? I am considering flashing a new kernel to get CWM Recovery and possibly blindly mount USB storage. But I don't know the current stock firmware so I'm unsure which version of Semaphore/CF-root to flash...
Is there any other way? Other than buying another i9000 with a working LCD/digitiser which would be too expensive.
darwinws said:
Hi all, I have an i9000 with a broken screen and digitiser. I need to recover the data from it (pictures mainly). There is no display at all but the phone is working otherwise - I can hear it booting up and I can put it into Download and Recovery modes.
Unfortunately it's running the stock firmware so I can't use Recovery Mode to mount USB storage. When turned on normally, it will connect to my PC but obviously I can't press the button to mount storage (why doesn't it mount automatically???).
Does anyone have any ideas? I am considering flashing a new kernel to get CWM Recovery and possibly blindly mount USB storage. But I don't know the current stock firmware so I'm unsure which version of Semaphore/CF-root to flash...
Is there any other way? Other than buying another i9000 with a working LCD/digitiser which would be too expensive.
Click to expand...
Click to collapse
Try this: http://78.46.194.137/kernels/Semaphore_2.7.4.tar . Flash it via Odin.
Gokulbalram said:
Try this: . Flash it via Odin.
Click to expand...
Click to collapse
Thanks for that. Is it definitely possible to flash it without interaction on the phone? I've flashed with Odin before but it's been a while.
If I did flash it successfully, do you know which version of CWM would it use? I need to know the exact order of options in the CWM Recovery so I could blind mount the USB storage...
darwinws said:
Thanks for that. Is it definitely possible to flash it without interaction on the phone? I've flashed with Odin before but it's been a while.
If I did flash it successfully, do you know which version of CWM would it use? I need to know the exact order of options in the CWM Recovery so I could blind mount the USB storage...
Click to expand...
Click to collapse
Well, I'm on KK and I'm using a kernel different from the one I sent you (Higher Version). I will let you know after some research!
Why don't you get your phone to the nearest Samsung Service Center otherwise?
Gokulbalram said:
Well, I'm on KK and I'm using a kernel different from the one I sent you (Higher Version). I will let you know after some research!
Why don't you get your phone to the nearest Samsung Service Center otherwise?
Click to expand...
Click to collapse
Cheers! I think it would be too expensive to take to a Service Centre unfortunately (plus there aren't any nearby). I'm looking at broken i9000s on Ebay at the moment, maybe I can find one for not too much and swap the parts over...
darwinws said:
Cheers! I think it would be too expensive to take to a Service Centre unfortunately (plus there aren't any nearby). I'm looking at broken i9000s on Ebay at the moment, maybe I can find one for not too much and swap the parts over...
Click to expand...
Click to collapse
Do you remember if you've enabled USB Debugging?
Gokulbalram said:
Do you remember if you've enabled USB Debugging?
Click to expand...
Click to collapse
Annoyingly I think it's disabled - I have tried using adb but it doesn't show up under devices. It's my sister's phone which is why it's not rooted (or backed up!) etc.
darwinws said:
Annoyingly I think it's disabled - I have tried using adb but it doesn't show up under devices. It's my sister's phone which is why it's not rooted (or backed up!) etc.
Click to expand...
Click to collapse
Okay, I'll try flashing the kernel myself and then let you know
---------- Post added at 05:29 PM ---------- Previous post was at 05:17 PM ----------
darwinws said:
Annoyingly I think it's disabled - I have tried using adb but it doesn't show up under devices. It's my sister's phone which is why it's not rooted (or backed up!) etc.
Click to expand...
Click to collapse
Okay! After flashing the kernel I asked you to and getting into recovery mode, click the volume down button 5 times and then, enter it and click again.
NOTE: The Backup will take at max half an hour. So, I suggest you leave it on charging whilst it backs up and take a look at it after 1 hour
Gokulbalram said:
Okay, I'll try flashing the kernel myself and then let you know
---------- Post added at 05:29 PM ---------- Previous post was at 05:17 PM ----------
Okay! After flashing the kernel I asked you to and getting into recovery mode, click the volume down button 5 times and then, enter it and click again.
NOTE: The Backup will take at max half an hour. So, I suggest you leave it on charging whilst it backs up and take a look at it after 1 hour
Click to expand...
Click to collapse
Thanks so much! Just to clarify - scrolling down 5 times and pressing enter twice mounts the USB storage? Then I can access the internal SD card and back up the contents using my PC?
Also for the flashing process - I put the phone in Download mode, connect it to PC and flash using Odin, selecting the 2.7.4 tar as PDA? Then disconnect phone and remove battery, then boot into CWM?
Also another issue I'm worried about is the current firmware on the phone, because apparently Semaphore 2.7.4 won't work on pre-JW4 firmwares. Is there any way to check the current firmware using Odin or something?
darwinws said:
Thanks so much! Just to clarify - scrolling down 5 times and pressing enter twice mounts the USB storage? Then I can access the internal SD card and back up the contents using my PC?
Also for the flashing process - I put the phone in Download mode, connect it to PC and flash using Odin, selecting the 2.7.4 tar as PDA? Then disconnect phone and remove battery, then boot into CWM?
Click to expand...
Click to collapse
Scrolling down 5 times and clicking twice runs the backup. You don't need to mount USB Storage! As for the flashing process you're right and it will work as long as you have the USB Drivers installed!
And yeah, the thanks button is right there (where ever it is).
Gokulbalram said:
Scrolling down 5 times and clicking twice runs the backup. You don't need to mount USB Storage! As for the flashing process you're right and it will work as long as you have the USB Drivers installed!
And yeah, the thanks button is right there (where ever it is).
Click to expand...
Click to collapse
Oh OK, where does the backup go? I'm not using a MicroSD at the moment. I think it would be best for me just to mount the USB storage so I can retrieve the photos etc to my PC. I don't need a full backup, I just need to transfer the important files to my PC.
Also you may have missed my previous comment, I'll paste it here:
Also another issue I'm worried about is the current firmware on the phone, because apparently Semaphore 2.7.4 won't work on pre-JW4 firmwares. Is there any way to check the current firmware using Odin or something?
darwinws said:
Oh OK, where does the backup go? I'm not using a MicroSD at the moment. I think it would be best for me just to mount the USB storage so I can retrieve the photos etc to my PC. I don't need a full backup, I just need to transfer the important files to my PC.
Also you may have missed my previous comment, I'll paste it here:
Also another issue I'm worried about is the current firmware on the phone, because apparently Semaphore 2.7.4 won't work on pre-JW4 firmwares. Is there any way to check the current firmware using Odin or something?
Click to expand...
Click to collapse
The Backup is mostly stored in the Internal SD Card. Regarding the flashing thing, Even if you flash a KK Kernel, it would boot to Recovery, but not to system.
Gokulbalram said:
The Backup is mostly stored in the Internal SD Card. Regarding the flashing thing, Even if you flash a KK Kernel, it would boot to Recovery, but not to system.
Click to expand...
Click to collapse
OK thanks again. Do you know the button sequence to mount USB storage? Sorry for the hassle!
darwinws said:
OK thanks again. Do you know the button sequence to mount USB storage? Sorry for the hassle!
Click to expand...
Click to collapse
No :/ My phone is kind of in a bad shape right now :crying:
Gokulbalram said:
No :/ My phone is kind of in a bad shape right now :crying:
Click to expand...
Click to collapse
No worries, thanks for the help anyway!

Categories

Resources