[Q] Phones keeps reboots after flashing rom - One (M7) Q&A, Help & Troubleshooting

I recently made my phone S-Off, used SuperCid and flashed an RUU.
Then I flashed viper rom and now want to flash either Paranoid android or Carbon but every time I do, the phone boots into the rom and then reboots or reboot from the boot splash.
I restored a backup from before the ViperRom flash and the problem still occur
Any help is greatly appreciated!
Using TWRP

parthami said:
I recently made my phone S-Off, used SuperCid and flashed an RUU.
Then I flashed viper rom and now want to flash either Paranoid android or Carbon but every time I do, the phone boots into the rom and then reboots or reboot from the boot splash.
I restored a backup from before the ViperRom flash and the problem still occur
Any help is greatly appreciated!
Using TWRP
Click to expand...
Click to collapse
Doesn't Viper require a special version of TWRP? You could try a newer version of TWRP or flash your stock firmware and do a reset in stock recovery. Then flash TWRP and a custom rom. Or run the RUU again.

majmoz said:
Doesn't Viper require a special version of TWRP? You could try a newer version of TWRP or flash your stock firmware and do a reset in stock recovery. Then flash TWRP and a custom rom. Or run the RUU again.
Click to expand...
Click to collapse
I updated TWRP, no change
I also ran the RUU again, no difference
Sidenote: The stock rom is rotated landscape after the RUU

parthami said:
I updated TWRP, no change
I also ran the RUU again, no difference
Sidenote: The stock rom is rotated landscape after the RUU
Click to expand...
Click to collapse
What RUU are you running and where did you get it?
What were the TWRP version numbers?
Could you post a fastboot getvar all except for imei and serialno?

majmoz said:
What RUU are you running and where did you get it?
What were the TWRP version numbers?
Could you post a fastboot getvar all except for imei and serialno?
Click to expand...
Click to collapse
RUU_M7_U_JB_50_HTC_EUROPE_1.29.401.2_R_Radio_4A.14.3250.13_10.33.1150.01_RELEASE_311663_SIGNED_2_4 (I just relised that thius might a Jellybean build, is that causing the issuse) from htc1guru
TWRP 2.8.0.2 and 2.7.1.1
Code:
C:\Android>fastboot getvar all
(bootloader) version 0.5
(bootloader) version-bootloader: 1.44.0000
(bootloader) version-baseband: 4A.14.3250.13
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version: PVT SHIP S-OFF
(bootloader) serialno: ******************
(bootloader) imei: ******************
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT_8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3961mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
getvar: all FAILED (status read failed(Too many links))
finshed. total time: 0.212s
Thanks for all your help so far!

parthami said:
RUU_M7_U_JB_50_HTC_EUROPE_1.29.401.2_R_Radio_4A.14.3250.13_10.33.1150.01_RELEASE_311663_SIGNED_2_4 (I just relised that thius might a Jellybean build, is that causing the issuse) from htc1guru
TWRP 2.8.0.2 and 2.7.1.1
Code:
C:\Android>fastboot getvar all
(bootloader) version 0.5
(bootloader) version-bootloader: 1.44.0000
(bootloader) version-baseband: 4A.14.3250.13
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version: PVT SHIP S-OFF
(bootloader) serialno: ******************
(bootloader) imei: ******************
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT_8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3961mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
getvar: all FAILED (status read failed(Too many links))
finshed. total time: 0.212s
Thanks for all your help so far!
Click to expand...
Click to collapse
Sorry, I was away for a few days. If you have not already, you might try a newer RUU you can get it from htc1guru or this site they have the OTAs to the present and a nandroid 5.11.401.10 just scroll down the page.

majmoz said:
Sorry, I was away for a few days. If you have not already, you might try a newer RUU you can get it from htc1guru or this site they have the OTAs to the present and a nandroid 5.11.401.10 just scroll down the page.
Click to expand...
Click to collapse
no worries
I've tried the x.xx401.x RUU K44 Europe and O2 but they both come up with error code 158

parthami said:
no worries
I've tried the x.xx401.x RUU K44 Europe and O2 but they both come up with error code 158
Click to expand...
Click to collapse
Try this Stock Firmware 4.19.401.9 first and then run the corresponding RUU.

majmoz said:
Try this Stock Firmware 4.19.401.9 first and then run the corresponding RUU.
Click to expand...
Click to collapse
Flashed the firmware and then Active cmdline overflow! came up so I have been trying to follow this guide but adb doesnt seem to work in recovery. Hopefully I can get this sorted out as my phone completely useless

parthami said:
Flashed the firmware and then Active cmdline overflow! came up so I have been trying to follow this guide but adb doesnt seem to work in recovery. Hopefully I can get this sorted out as my phone completely useless
Click to expand...
Click to collapse
Take a look at FAQ Q#2 for help with ADB.

majmoz said:
Take a look at FAQ Q#2 for help with ADB.
Click to expand...
Click to collapse
I somehow got it working before your post but I will still read the FAQ fully, thanks!
Currently on the RUU so hopefully will be able to flash what I need but sadly can not charge which is a problem I have with sense roms
EDIT: Back to the original question, after flashing the stock firmware and RUU, flashing PA still results in reboot after booting into the rom once I start going though the gapps getup. If I dont touch anything it doesnt reboot

parthami said:
I somehow got it working before your post but I will still read the FAQ fully, thanks!
Currently on the RUU so hopefully will be able to flash what I need but sadly can not charge which is a problem I have with sense roms
EDIT: Back to the original question, after flashing the stock firmware and RUU, flashing PA still results in reboot after booting into the rom once I start going though the gapps getup. If I dont touch anything it doesnt reboot
Click to expand...
Click to collapse
I don't use PA, but maybe it is something in the way it is compiled that is causing you the issue. The two version I looked at were both beta builds which means there maybe bugs. Sorry, I can not help you on this one. I think you may have enough post to post in the development forum so you could possibiliy post your question there. 
 @v7znay Could you help parthami with his bootloop issue with PA?

majmoz said:
I don't use PA, but maybe it is something in the way it is compiled that is causing you the issue. The two version I looked at were both beta builds which means there maybe bugs. Sorry, I can not help you on this one. I think you may have enough post to post in the development forum so you could possibiliy post your question there.
@v7znay Could you help parthami with his bootloop issue with PA?
Click to expand...
Click to collapse
No worries, you have been a tremendous help so far! I will try with Carbon or CM and hopefully that works
Any way I can repay you, please let me know
EDIT: The problem happens with CM so clearly not a issue with particular rom

Related

[Q] Flash RUU problem - PLEASE HELP!

Please help, I have a big problem!
I accidently flashed a rom that required S-off but my device is S-on and now it keeps rebooting. After that I tried to install Stock Sense(fflashable .zip) but when it almost completed, it failed. Now if I reboot it it doesn't go further than the HTC logo screen. I did some research to flash the stock sense on it but I don't know which RUU I have to flash. My the device is the international version unlocked (m7ul). My radio is radio-4a.17.3250.14
my getvar:
bootloader version: 0.5
version-bootloader: 1.54.0000
version-baseband: 4A.17.3250.14
version-clpd: None
version-microp: None
version-main:
version-misc: PUT SHIP S-ON
serialno:
imei:
meid: 000000000000000000
product: m7_ul
platform: HBOOT-8064
modelid: PN0710000
cidnum: HTC_E11
battery-status: good
battery-voltage: 3914 mV
partition-layout: Generic
security: on
build-mode: ship
boot-mode: fastboot
commitno-bootloader: dirty-d959c75800
hbootpreupdate: 11
gencheckpt: 0
all: Done!
finished. Total time 0.048s
Please help me
Thanks
LMH1998 said:
Please help, I have a big problem!
I accidently flashed a rom that required S-off but my device is S-on and now it keeps rebooting. After that I tried to install Stock Sense(fflashable .zip) but when it almost completed, it failed. Now if I reboot it it doesn't go further than the HTC logo screen. I did some research to flash the stock sense on it but I don't know which RUU I have to flash. My the device is the international version unlocked (m7ul). My radio is radio-4a.17.3250.14
my getvar:
bootloader version: 0.5
version-bootloader: 1.54.0000
version-baseband: 4A.17.3250.14
version-clpd: None
version-microp: None
version-main:
version-misc: PUT SHIP S-ON
serialno:
imei:
meid: 000000000000000000
product: m7_ul
platform: HBOOT-8064
modelid: PN0710000
cidnum: HTC_E11
battery-status: good
battery-voltage: 3914 mV
partition-layout: Generic
security: on
build-mode: ship
boot-mode: fastboot
commitno-bootloader: dirty-d959c75800
hbootpreupdate: 11
gencheckpt: 0
all: Done!
finished. Total time 0.048s
Please help me
Thanks
Click to expand...
Click to collapse
read this thread to look for your stock ROM: here and flash it
then if you want S-OFF then follow this detailed guide: here
kamilmirza said:
read this thread to look for your stock ROM: here and flash it
if you want S-OFF then follow this detailed guide: here
Click to expand...
Click to collapse
I don't get any devica-main code so I really don't know which one to download, but I've downloaded one, but when I try to flash it, It always fails at: (boatloader) checking signature.
LMH1998 said:
I don't get any devica-main code so I really don't know which one to download, but I've downloaded one, but when I try to flash it, It always fails at: (boatloader) checking signature.
Click to expand...
Click to collapse
this is because you the tried to flash something (ROM or any other package) with S-ON
you have to flash it with custom recovery, CWM or TWRP
which one you selected?
kamilmirza said:
this is because you the tried to flash something (ROM or any other package) with S-ON
you have to flash it with custom recovery, CWM or TWRP
which one you selected?
Click to expand...
Click to collapse
So I'll tell you my story.
First it was on sense, then I installed OneDroid using TWRP v2.6.3.3, It worked perfectly fine but battery drain was to bad so I decided to return to Sense, so I flashed a flashable .zip. Eveyrthing worked ok. Then I heard that AOKP had better battery life so I downloaded it, but it didn't want to install, It kept saying ERROR. Then I've thought of flashing the Google Play Edition. So here everything went wrong. it tried to flash with TWRP but It got failed aswell. then I flashed CWM on it, installed the Google Play Edition rom and rebooted my phone, after 3 seconds it reboots, and it keeps on rebooting. but eventually I got back into Recovery and flashed the Sense rom that I still had on my phone. But when I was installing that, It got failed. Then I tried to flash TWRP to install the Sense rom, but after I flashed TWRP, I couldn't go back into recovery. Then the phone get stuck on the HTC logo screen.
So now I want to flash Sense with RUU but I don't know which one to install and it fails when I flash the .zip with cmd. It fails at "checking signature".
PLEASE PEOPLE HELP ME, it's my brother phone's and I messed up
LMH1998 said:
So I'll tell you my story.
First it was on sense, then I installed OneDroid using TWRP v2.6.3.3, It worked perfectly fine but battery drain was to bad so I decided to return to Sense, so I flashed a flashable .zip. Eveyrthing worked ok. Then I heard that AOKP had better battery life so I downloaded it, but it didn't want to install, It kept saying ERROR. Then I've thought of flashing the Google Play Edition. So here everything went wrong. it tried to flash with TWRP but It got failed aswell. then I flashed CWM on it, installed the Google Play Edition rom and rebooted my phone, after 3 seconds it reboots, and it keeps on rebooting. but eventually I got back into Recovery and flashed the Sense rom that I still had on my phone. But when I was installing that, It got failed. Then I tried to flash TWRP to install the Sense rom, but after I flashed TWRP, I couldn't go back into recovery. Then the phone get stuck on the HTC logo screen.
So now I want to flash Sense with RUU but I don't know which one to install and it fails when I flash the .zip with cmd. It fails at "checking signature".
PLEASE PEOPLE HELP ME, it's my brother phone's and I messed up
Click to expand...
Click to collapse
are you on TWRP?
if so when you select the ROM to flash, uncheck the verification md5 something
kamilmirza said:
are you on TWRP?
if so when you select the ROM to flash, uncheck the verification md5 something
Click to expand...
Click to collapse
I can't get back into recovery. Getting into the boatloader is the only thing I can do
Please try to find me the right RUU and a RUU that doesn't requires S-off, that would be awesome!
LMH1998 said:
I can't get back into recovery. Getting into the boatloader is the only thing I can do
Please try to find me the right RUU and a RUU that doesn't requires S-off, that would be awesome!
Click to expand...
Click to collapse
tell me your CID, can you remember your main?
flash TWRP via fastboot method (bootloader)
kamilmirza said:
tell me your CID, can you remember your main?
flash TWRP via fastboot method (bootloader)
Click to expand...
Click to collapse
Sorry but I'm super noob in HTC ONE devolpment, I'm more into Xperia devolping but where can I find the CID?
I really can't remember the main.
but the device is bought in Belgium, Europe. Maybe that can help you to find it.
LMH1998 said:
I can't get back into recovery. Getting into the boatloader is the only thing I can do
Please try to find me the right RUU and a RUU that doesn't requires S-off, that would be awesome!
Click to expand...
Click to collapse
i understand you are anxious, but please calm down, before you end up with a brick; (and please don't cross-post, it just get's everybody confused)
I'll be back in a little while, but in the meantime can you confirm,
1- you have bootloader unlocked
2- what OS are you running (Win7 / 8 / 8.1, Ubuntu, Mac)
3- do not type the output of "fastboot getvar all", use copy/paste
nkk71 said:
i understand you are anxious, but please calm down, before you end up with a brick; (and please don't cross-post, it just get's everybody confused)
I'll be back in a little while, but in the meantime can you confirm,
1- you have bootloader unlocked
2- what OS are you running (Win7 / 8 / 8.1, Ubuntu, Mac)
3- do not type the output of "fastboot getvar all", use copy/paste
Click to expand...
Click to collapse
1. I relocked the boatloader because I watched a tutorial on how to flash stock rom so my boatloader is locked.
2. I'm running Windows 7 64bit Ultimate
3. C:\fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.54.0000
(bootloader) version-baseband: 4A.17.3250.14
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__E11
(bootloader) battery-status: good
(bootloader) battery-voltage: 4062mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-d959c75800
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.046s
LMH1998 said:
1. I relocked the boatloader because I watched a tutorial on how to flash stock rom so my boatloader is locked.
2. I'm running Windows 7 64bit Ultimate
3. C:\fastboot>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.54.0000
(bootloader) version-baseband: 4A.17.3250.14
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: xxx
(bootloader) imei: xxx
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__E11
(bootloader) battery-status: good
(bootloader) battery-voltage: 4062mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-d959c75800
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.046s
Click to expand...
Click to collapse
remove your SERIALNO and IMEI from your post
be patient and good luck :good:
@nkk71 will guide you through and now you are in good hands
kamilmirza said:
remove your SERIALNO and IMEI from your post
be patient and good luck :good:
@nkk71 will guide you through and now you are in good hands
Click to expand...
Click to collapse
i hope you're right.
---------- Post added at 09:07 PM ---------- Previous post was at 09:05 PM ----------
LMH1998 said:
1. I relocked the boatloader because I watched a tutorial on how to flash stock rom so my boatloader is locked.
2. I'm running Windows 7 64bit Ultimate
3. C:\fastboot>fastboot getvar all
(bootloader) version-bootloader: 1.54.0000
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) product: m7_ul
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__E11
finished. total time: 0.046s
Click to expand...
Click to collapse
so hboot 1.54 (HTC__E11) = 2.24.401.x firmware.
so first, get yourself unlocked again, we need s-off
use HTCdev to get an unlock token and unlock...
[/QUOTE]so hboot 1.54 (HTC__E11) = 2.24.401.x firmware.
so first, get yourself unlocked again, we need s-off
use HTCdev to get an unlock token and unlock...[/QUOTE]
I unlocked my bootloader again
nkk71 said:
i hope you're right.
---------- Post added at 09:07 PM ---------- Previous post was at 09:05 PM ----------
so hboot 1.54 (HTC__E11) = 2.24.401.x firmware.
so first, get yourself unlocked again, we need s-off
use HTCdev to get an unlock token and unlock...
Click to expand...
Click to collapse
I unlocked my boatloader again
LMH1998 said:
I unlocked my boatloader again
Click to expand...
Click to collapse
:good::good:
do you have a functioning ROM? you'll need to use rumrunner to get s-off
i believe you need a rooted ROM, preferably with unsecured kernel.
what recovery are you on, and what ROM?
nkk71 said:
:good::good:
do you have a functioning ROM? you'll need to use rumrunner to get s-off
i believe you need a rooted ROM, preferably with unsecured kernel.
what recovery are you on, and what ROM?
Click to expand...
Click to collapse
Tha problem is that I don't have any ROM on it now, but I do have a ROM on the memory of the phone(Sense rom) and I'm using TWRP v2.6.3.3 but I can't go into recovery Don't know why...
Nevermind I can get back into recovery but everything got erased
LMH1998 said:
Tha problem is that I don't have any ROM on it now, but I do have a ROM on the memory of the phone(Sense rom) and I'm using TWRP v2.6.3.3 but I can't go into recovery Don't know why...
Nevermind I can get back into recovery but everything got erased
Click to expand...
Click to collapse
i need to go for about an hour (+ or -), can you check your PM....
nkk71 said:
i need to go for about an hour (+ or -), can you check your PM....
Click to expand...
Click to collapse
Yeah ok I can do that.
and btw my CID is HTC__E11
LMH1998 said:
Yeah ok I can do that.
and btw my CID is HTC__E11
Click to expand...
Click to collapse
Sorry didn't come back yesterday, but I'll be online a bit later...
In the meantime, flash the ROM I sent you, and use http://rumrunner.us/ to get s-off
to get the rom to your phone, go to custom recovery (CWM or TWRP), then use one of the following methods:
1- OTG cable
2- adb push <name of rom>.zip /data/media/0/
3- adb sideload <name of rom>.zip
example of adb push:
Code:
C:\ADB2>[B]adb push Guru_Reset_M7_3.62.401.1.zip /data/media/0/[/B]
2922 KB/s (1102709591 bytes in 368.450s)
note that adb push will not show any kind of progress until it completes (about 5 to 10 minutes).
and finally choose "install" in CWM or TWRP and install it.
then use rumrunner; remember reading the rumrunner instruction (especially the firewall/antivirus etc).

[Q] HELP with updating HTC One to 4.4...

Hello, I have a rooted international HTC One currently running 4.3 Android with Sense 5.0. I am trying to perform an OTA system update that I have received... I downloaded the new 4.4 Android (1.1 GB) and I have selected "Install Update". But when the phone restarts, it just enters recovery and opens TWRP by itself!
So then I try to flash the downloaded OTA file via TWRP, but that also fails... Does anyone know how I can get 4.4 on my HTC One? Thank you
arbank94 said:
Hello, I have a rooted international HTC One currently running 4.3 Android with Sense 5.0. I am trying to perform an OTA system update that I have received... I downloaded the new 4.4 Android (1.1 GB) and I have selected "Install Update". But when the phone restarts, it just enters recovery and opens TWRP by itself!
So then I try to flash the downloaded OTA file via TWRP, but that also fails... Does anyone know how I can get 4.4 on my HTC One? Thank you
Click to expand...
Click to collapse
You can't apply ota with a custom recovery, you need your stock recovery.
arbank94 said:
Hello, I have a rooted international HTC One currently running 4.3 Android with Sense 5.0. I am trying to perform an OTA system update that I have received... I downloaded the new 4.4 Android (1.1 GB) and I have selected "Install Update". But when the phone restarts, it just enters recovery and opens TWRP by itself!
So then I try to flash the downloaded OTA file via TWRP, but that also fails... Does anyone know how I can get 4.4 on my HTC One? Thank you
Click to expand...
Click to collapse
Depending on whats been done to the phone you can eather flash stock recovery and try the update from their or you have to ruu back to stock and take the update that way.
fastboot getvar all will tell you what stock recovery you need or what ruu to use
alray said:
You can't apply ota with a custom recovery, you need your stock recovery.
Click to expand...
Click to collapse
So would you recommend getting stock recovery following nkk71's guide in your signature, or should I just flash a 4.4 rom?
arbank94 said:
So would you recommend getting stock recovery following nkk71's guide in your signature, or should I just flash a 4.4 rom?
Click to expand...
Click to collapse
Do what cIsA said. Check the output of "fastboot getvar all". Look at your main-ver # and find the corresponding stock recovery. There is a thread in general section with a collection of stock recovery.
You can post the output of getvar here minus imei/sn and we will link you the correct recovery.
Okay so I ran a fastboot getvar all, and apparently there is no RUU for my device, because it is Latin American with a CID of HTC_332. (I searched almost everywhere)
Now, after flashing a 4.4 rom I downloaded, my HTC device wasn't turning on anymore (it was getting stuck at the HTC boot logo). So I restored from a backup I made in TWRP, and that didn't work either. So now my problem just got 1000x worse because of a mistake I just made now of completely wiping my device and the OS.
So for the moment I'll try to flash a new boot.img, get S-OFF again, and change the CID to 11111111 (as I have read) where I will then download a RUU I can use. I'll let you know what happens.
Whoa there.. No need to flash boot.IMG.
What's you're steps? I think you are about to make it worse
sent from my mobile device
Okay well I'm in a tight situation atm.
My phone is completely wiped, with no OS or anything. The only thing I have access to is fastboot, and the TWRP bootloader. Also considering my phone is wiped, I believe I have S-ON as well.
So what is the first step to just get a boot going? (unless I'm not completely screwed that is..)
EDIT- I have successfully flashed Android Revolution to my phone from TWRP by pushing the zip via adb fastboot. Got my phone running again. Step 1 complete.
Step 2 now is to get S-OFF again...
Step 3- Change my CID to 11111111 using the SuperCID method (there is no RUU for my Latin American CID; HTC_332)
Step 4- Use an appropriate RUU to get 4.4 stock after I have changed my CID.
Before I continue with these steps, can anyone confirm with me if I am on the right path?
Step 2 - Confirmed.
Step 3 & Step 4 ... What is an appropriate RUU? You have not yet posted a fastboot getvar all output yet. (remove imei)
SaHiLzZ said:
Step 2 - Confirmed.
Step 3 & Step 4 ... What is an appropriate RUU? You have not yet posted a fastboot getvar all output yet. (remove imei)
Click to expand...
Click to collapse
I had the same cid when I bought mine. Irc, MID was PN0711000 with s.w. X.XX.599.X.
so he could use the 1.29.401.2 ruu on htc1guru but he have to change cid.
---------- Post added at 08:04 PM ---------- Previous post was at 08:02 PM ----------
arbank94 said:
EDIT- I have successfully flashed Android Revolution to my phone from TWRP by pushing the zip via adb fastboot. Got my phone running again.
Before I continue with these steps, can anyone confirm with me if I am on the right path?
Click to expand...
Click to collapse
You could just stay with arhd, its a very good rom...
alray said:
You could just stay with arhd, its a very good rom...
Click to expand...
Click to collapse
Agreed!:laugh:
alray said:
I had the same cid when I bought mine. Irc, MID was PN0711000 with s.w. X.XX.599.X.
so he could use the 1.29.401.2 ruu on htc1guru but he have to change cid.
---------- Post added at 08:04 PM ---------- Previous post was at 08:02 PM ----------
You could just stay with arhd, its a very good rom...
Click to expand...
Click to collapse
C:\Users\Arban\Downloads\adt-bundle-windows-x86_64-20131030\adt-bundle-windows-x
86_64-20131030\sdk\platform-tools>adb push htcrom2.zip /sdcard/
3455 KB/s (1180577030 bytes in 333.659s)
C:\Users\Arban\Downloads\adt-bundle-windows-x86_64-20131030\adt-bundle-windows-x
86_64-20131030\sdk\platform-tools>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.55.0000
(bootloader) version-baseband: 4A.20.3263.16
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: SH392W901414
(bootloader) imei: **************
(bootloader) meid: 00000000000000
(bootloader) product: m7_u
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0711000
(bootloader) cidnum: HTC__332
(bootloader) battery-status: good
(bootloader) battery-voltage: 4318mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-e0349bfc
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.045s
So yeah... there's no RUU as I said.
alray, in order to use that 1.29.401.2 RUU, what do I have to change my CID to?
EDIT: I'll just stick with your suggestion alray and stay with ARHD lol. (but in case I change my mind, what CID should I change to for that RUU?... so that I won't have to bump this thread or make a new one later)
arbank94 said:
C:\Users\Arban\Downloads\adt-bundle-windows-x86_64-20131030\adt-bundle-windows-x
86_64-20131030\sdk\platform-tools>adb push htcrom2.zip /sdcard/
3455 KB/s (1180577030 bytes in 333.659s)
C:\Users\Arban\Downloads\adt-bundle-windows-x86_64-20131030\adt-bundle-windows-x
86_64-20131030\sdk\platform-tools>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.55.0000
(bootloader) version-baseband: 4A.20.3263.16
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: SH392W901414
(bootloader) imei: **************
(bootloader) meid: 00000000000000
(bootloader) product: m7_u
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0711000
(bootloader) cidnum: HTC__332
(bootloader) battery-status: good
(bootloader) battery-voltage: 4318mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-e0349bfc
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
finished. total time: 0.045s
So yeah... there's no RUU as I said.
alray, in order to use that 1.29.401.2 RUU, what do I have to change my CID to?
EDIT: I'll just stick with your suggestion alray and stay with ARHD lol. (but in case I change my mind, what CID should I change to for that RUU?... so that I won't have to bump this thread or make a new one later)
Click to expand...
Click to collapse
These CID:
HTC__001
HTC__J15
HTC__A48
HTC__M27
are compatible with the 1.29.401.2 ruu.zip so i'll suggest you to use HTC__001 if you change your mind. Personally, I would stay on ARHD. No benefit to flash that RUU vs ARHD. ARHD is always up to date...

[Q] Can't start my HTC One

Hi guys I'm new on this forum and I hope this is the right place to put this thread.
I wanted to try the Cyanogenmod with my HTC One and got it installed and working properly but then I decided that the mod was not for me and I wanted to go back to the normal os, now I dont have any os at all and for some reason I can't start the cyanogenmod again, I have read a lot of threads and guides on how to fix this but I haven't found the right thread for me so I thought I would start my own. I should also mention that I tried a lot of these fixes and probably made the situation worse but I hope I can still fix this.
What do you need to know to possibly help me and what do I need?
And since I'm completely new on everything related to anything please explain things as simple as possible
Thanks in advance!
Pangkakan said:
What do you need to know to possibly help me
Click to expand...
Click to collapse
The output of fastboot getvar all except IMEI and SERIALNO
alray said:
The output of fastboot getvar all except IMEI and SERIALNO
Click to expand...
Click to collapse
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.56.0000
(bootloader) version-baseband: 4A.23.3263.28
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 4.19.401.8
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__Y13
(bootloader) battery-status: good
(bootloader) battery-voltage: 4291mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-4dab9d12
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
Pangkakan said:
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.56.0000
(bootloader) version-baseband: 4A.23.3263.28
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 4.19.401.8
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno:
(bootloader) imei:
(bootloader) meid: 00000000000000
(bootloader) product: m7_ul
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0710000
(bootloader) cidnum: HTC__Y13
(bootloader) battery-status: good
(bootloader) battery-voltage: 4291mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-4dab9d12
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
Click to expand...
Click to collapse
Did you make a nandroid backup from recovery before you installed cyanogenmod?
Or you could flash ARHD 53 rom, it looks like the stock rom + some extra feature. Very stable rom and always up to date.
What recovery version are you using?
alray said:
Did you make a nandroid backup from recovery before you installed cyanogenmod?
Or you could flash ARHD 53 rom, it looks like the stock rom + some extra feature. Very stable rom and always up to date.
What recovery version are you using?
Click to expand...
Click to collapse
No i did not do a nandroid backup before.
Is there no way to get stock rom at all?
Recovery version is ClockworkMod Recovery v6.0.4.6
Pangkakan said:
No i did not do a nandroid backup before.
Is there no way to get stock rom at all?
Recovery version is ClockworkMod Recovery v6.0.4.6
Click to expand...
Click to collapse
This ruu looks like it's for your device. Will return to stock, but will wipe your device.
http://androidruu.com/getdownload.p...10.38r.1157.04L_release_353069_signed_2-1.exe
Pangkakan said:
No i did not do a nandroid backup before.
Click to expand...
Click to collapse
Always make a nandroid backup before you tamper with the phone! If you had, would have been very easy to go back to stock.
Pangkakan said:
Is there no way to get stock rom at all?
Recovery version is ClockworkMod Recovery v6.0.4.6
Click to expand...
Click to collapse
There is a stock 4.19.401.11 rom uploaded by arhd here. You'll have to manually flash the corresponding firmware if you want to be 100% stock. I'll suggest you tu use TWRP 2.6.3.3 instead of CWM.
Go ahead with the ruu posted above.
---------- Post added at 12:07 PM ---------- Previous post was at 12:03 PM ----------
mb_guy said:
This ruu looks like it's for your device. Will return to stock, but will wipe your device.
http://androidruu.com/getdownload.p...10.38r.1157.04L_release_353069_signed_2-1.exe
Click to expand...
Click to collapse
Hey thanks for your reply! I did not now they released a new ruu for .401. Will make thing much easier! :good:
mb_guy said:
This ruu looks like it's for your device. Will return to stock, but will wipe your device.
Click to expand...
Click to collapse
Thanks I will try that one.
alray said:
Always make a nandroid backup before you tamper with the phone! If you had, would have been very easy to go back to stock.
There is a stock 4.19.401.11 rom uploaded by arhd here. You'll have to manually flash the corresponding firmware if you want to be 100% stock. I'll suggest you tu use TWRP 2.6.3.3 instead of CWM.
Go ahead with the ruu posted above.
---------- Post added at 12:07 PM ---------- Previous post was at 12:03 PM ----------
Hey thanks for your reply! I did not now they released a new ruu for .401. Will make thing much easier! :good:
Click to expand...
Click to collapse
Yeah I realize I should have done a backup but I'm not used to doing stuff like this with my phone and didn't do enough research before, but you learn from your mistakes I guess.
Thanks for the help I will try the ruu mb_guy posted and hopefully it will work
Pangkakan said:
Thanks I will try that one.
Yeah I realize I should have done a backup but I'm not used to doing stuff like this with my phone and didn't do enough research before, but you learn from your mistakes I guess.
Thanks for the help I will try the ruu mb_guy posted and hopefully it will work
Click to expand...
Click to collapse
The ruu.exe should work flawlessly but don't forget, with S-ON you need to relock bootloader to use it! Note that the ruu will wipe everything including your sdcard so backup your personal/media files before.
Code:
fastboot oem lock
also better to md5 checksum the ruu.exe before running it!
md5:
9ad4111ce86981e3dffcce6d9ee80551
alray said:
The ruu.exe should work flawlessly but don't forget, with S-ON you need to relock bootload to use it! Note that the ruu will wipe everything including your sdcard so backup your personal/media files before.
Click to expand...
Click to collapse
So I should use the fastboot oem lock command and then its just to install the exe?
Pangkakan said:
So I should use the fastboot oem lock command and then its just to install the exe?
Click to expand...
Click to collapse
yes also read my post above (edited a few sec ago)
md5 check sum the ruu.exe before.
alray said:
yes also read my post above (edited a few sec ago)
md5 check sum the ruu.exe before.
Click to expand...
Click to collapse
What is md5 checksum? I googled it but I don't really understand :/
Pangkakan said:
What is md5 checksum? I googled it but I don't really understand :/
Click to expand...
Click to collapse
md5 is to check if the file you downloaded (i.e your ruu) is not corrupted (bad download)
use this small software to check md5 https://dl.dropboxusercontent.com/u/77459918/WinMD5.exe
select your ruu.exe and copy/paste the md5 checksum I have posted above. If this match then your safe to run the ruu. If not, then re-download the file.
alray said:
md5 is to check if the file you downloaded (i.e your ruu) is not corrupted (bad download)
use this small software to check md5 https://dl.dropboxusercontent.com/u/77459918/WinMD5.exe
select your ruu.exe and copy/paste the md5 checksum I have posted above. If this match then your safe to run the ruu. If not, then re-download the file.
Click to expand...
Click to collapse
Thanks man for taking your time and helping me, it works! You and mb_guy are my favourite persons right now!
Pangkakan said:
Thanks man for taking your time and helping me, it works! You and mb_guy are my favourite persons right now!
Click to expand...
Click to collapse
glad it worked. if you flash a new rom in the future, make a nandroid backup from custom recovery before. Also a good idea to make a copy of that backup up on your computer.
mb_guy said:
This ruu looks like it's for your device. Will return to stock, but will wipe your device.
Click to expand...
Click to collapse
I have the same device, tried this RUU but it stuck @ 5%,i even tried to manually flash the .zip, nothing seems to work :S

[Q] HTC ONE M7 stuck in boot loop, S-On is back on hboot 1.44.0000

I need help fixing my phone. I was flashing a sense 6 rom and after the aroma installer, my device rebooted into hboot and reboots if i try to reboot, power down, or go into recovery.
I need help please
one_mic_only said:
I need help fixing my phone. I was flashing a sense 6 rom and after the aroma installer, my device rebooted into hboot and reboots if i try to reboot, power down, or go into recovery.
I need help please
Click to expand...
Click to collapse
Please give us a few more information.....
which rom were you flashing ?
Which recovery do you have ?
So you can't acces into recovery ?
Boachti said:
Please give us a few more information.....
which rom were you flashing ?
Which recovery do you have ?
So you can't acces into recovery ?
Click to expand...
Click to collapse
i flashed renovate
i now have 2.7.0.3 recovery
and i'm able to get into recovery and i restored
i'm just trying to get s off and try the bad boys sense 6 rom
one_mic_only said:
i flashed renovate
i now have 2.7.0.3 recovery
and i'm able to get into recovery and i restored
i'm just trying to get s off and try the bad boys sense 6 rom
Click to expand...
Click to collapse
you should be a bit more specific (renovate and 2.7.0.3 could mean a lot of things
1- start by posting a "fastboot getvar all" (excluding IMEI, MEID, and s/n)
2- an actual link to the threads (and downloads) of the files (and versions) you mentioned... cause i don't see TWRP 2.7.0.3 in either the m7_u/ul or the m7_wls models
I'm assuming TWRP, but you know what they say about assumption...
nkk71 said:
you should be a bit more specific (renovate and 2.7.0.3 could mean a lot of things
1- start by posting a "fastboot getvar all" (excluding IMEI, MEID, and s/n)
2- an actual link to the threads (and downloads) of the files (and versions) you mentioned... cause i don't see TWRP 2.7.0.3 in either the m7_u/ul or the m7_wls models
I'm assuming TWRP, but you know what they say about assumption...
Click to expand...
Click to collapse
here's the link
http://forum.xda-developers.com/showthread.php?t=2692922
and yes we all know what they say lol
i'm just trying to s-off now, cause i can't flash any of those roms without being s-off correct?
i alway root my phone, s-off, then fall into the land of the lost when it comes to going thru this process again. at least i saved myself from flat out brick.
one_mic_only said:
here's the link
http://forum.xda-developers.com/showthread.php?t=2692922
and yes we all know what they say lol
i'm just trying to s-off now, cause i can't flash any of those roms without being s-off correct?
i alway root my phone, s-off, then fall into the land of the lost when it comes to going thru this process again. at least i saved myself from flat out brick.
Click to expand...
Click to collapse
i thought only GPE ROMs require S-Off... didnt see anything in the OP about having to be S-Off.
anyway, if you're trying to S-Off best use a ROM which is inline with your firmware (so check your fastboot getvar all), then find a ROM based on the same version (rooted with unsecured kernel) and use firewater to get s-off
at least we now know you're on Sprint... cause you've only linked Sprint stuff ... i'm assuming
yes i'm on sprint lol
and here ya go
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.44.0000
(bootloader) version-baseband: 1.00.20.0315
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main: 1.29.651.10
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) serialno: FA348S905516
(bootloader) imei: 990001465400661
(bootloader) meid: 99000146540066
(bootloader) product: m7_wls
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0720000
(bootloader) cidnum: SPCS_001
(bootloader) battery-status: good
(bootloader) battery-voltage: 4043mV
(bootloader) partition-layout: Generic
(bootloader) security: on
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-5d8b0f7651bb88c960f701ae91477674a
getvar:all FAILED (unknown status code)
finished. total time: 0.069s
any suggestions for a rom that will work? i'm about to try badseed now.
one_mic_only said:
yes i'm on sprint lol
and here ya go
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.44.0000
(bootloader) version-baseband: 1.00.20.0315
(bootloader) version-main: 1.29.651.10
(bootloader) version-misc: PVT SHIP S-ON
(bootloader) product: m7_wls
(bootloader) modelid: PN0720000
(bootloader) cidnum: SPCS_001
finished. total time: 0.069s
any suggestions for a rom that will work? i'm about to try badseed now.
Click to expand...
Click to collapse
actually, yes
hboot 1.44
http://forum.xda-developers.com/showpost.php?p=48955645&postcount=250
ARHD 9.4 is Sprint compatible (select Sprint in the installer), it's rooted, it has an unsecured kernel, and you can even use revone to S-Off
http://firewater-soff.com/ and http://rumrunner.us/ should work also, your choice
thanks.
think i'll try rum. revone aint working.

[Q] htc one sprint ruu failing. help please

Help please?? I am trying to RUU my HTC One. I successfully relocked my bootloader.
However, when I start the process, it fails (unknown error). I am told that I need to use the "correct" RUU and try again. My problem is that the one I am using claims to be correct. Sprint_HTD_One_m7wls_1.29651.10_RUU.zip
I have noticed that when I am going through the RUU process I am shown the screen that asks to compare the current version with the new one. The current image version is blank. Nothing there. No current image version at all.
slaldrich said:
Help please?? I am trying to RUU my HTC One. I successfully relocked my bootloader.
However, when I start the process, it fails (unknown error). I am told that I need to use the "correct" RUU and try again. My problem is that the one I am using claims to be correct. Sprint_HTD_One_m7wls_1.29651.10_RUU.zip
I have noticed that when I am going through the RUU process I am shown the screen that asks to compare the current version with the new one. The current image version is blank. Nothing there. No current image version at all.
Click to expand...
Click to collapse
post the output of ''fastboot getvar all'' except imei and sn
alray said:
post the output of ''fastboot getvar all'' except imei and sn
Click to expand...
Click to collapse
Here it is:
version: 0.5
version-bootloader: 1.56.0000
version-baseband: N/A
version-cpld: none
version-microp:none
version- main:
version -misc: PVT SHIP S-ON
serialno: (you asked this not be included) but it is present
meid: number present, not included
product: m7_wls
platform: HBOOT-8064
modelid: PN0720000
cidnum: SPCS_001
battery status: good
battery voltage: 4280mV
partition-layout: Generic
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: dirty-4dab9d12
hbootpreupdate 11
gencheckpt: 0
I also notice that on the fastboot screen, it reads:
**TAMPERED**
**RELOCKED**
**SECURITY WARNING**
m7_WLS PVT SHIP S-ON RH
HBOOT- 1.56.0000
OpenDSP- v32. 120.274.0909
OS- (blank)
eMMC-boot 2048 MB
Jan.23 2014, 22:11:35.0
thanks for looking at this!
slaldrich said:
Here it is:
version: 0.5
version-bootloader: 1.56.0000
version-baseband: N/A
version-cpld: none
version-microp:none
version- main:
version -misc: PVT SHIP S-ON
serialno: (you asked this not be included) but it is present
meid: number present, not included
product: m7_wls
platform: HBOOT-8064
modelid: PN0720000
cidnum: SPCS_001
battery status: good
battery voltage: 4280mV
partition-layout: Generic
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: dirty-4dab9d12
hbootpreupdate 11
gencheckpt: 0
thanks for looking at this!
Click to expand...
Click to collapse
The RUU you are trying to flash is a downgrade, thats why you can't flash it. 1.29.651.10 is for hboot 1.44 and you are on 1.56. You need s-off to downgrade with a ruu.
Refer to the sprint htc one forum to see if this is possible to s-off your phone on hboot 1.56 and then downgrade using the ruu
or
flash a rom for sprint htc one.
alray said:
The RUU you are trying to flash is a downgrade, thats why you can't flash it. 1.29.651.10 is for hboot 1.44 and you are on 1.56. You need s-off to downgrade with a ruu.
Refer to the sprint htc one forum to see if this is possible to s-off your phone on hboot 1.56 and then downgrade using the ruu
or
flash a rom for sprint htc one.
Click to expand...
Click to collapse
I understand s-off isn't possible. can you give me direction for getting started with your second suggestion "flash a rom for sprint htc one"?
slaldrich said:
I understand s-off isn't possible. can you give me direction for getting started with your second suggestion "flash a rom for sprint htc one"?
Click to expand...
Click to collapse
first your bootloader is relocked, you'll need to unlock it.
flash twrp recovery for M7WLS (sprint variant)
then download a sprint compatible rom. You can find them here .
push it to your phone and flash it.
If you have questions about how to do any of these steps ask me here, we'll go step by step...
alray said:
first your bootloader is relocked, you'll need to unlock it.
flash twrp recovery for M7WLS (sprint variant)
then download a sprint compatible rom. You can find them here .
push it to your phone and flash it.
If you have questions about how to do any of these steps ask me here, we'll go step by step...
Click to expand...
Click to collapse
My basic problem is that my radios were not connecting with Sprint at all. So, I understand that I need to do a RUU to fix that. Flashing a custom rom won't fix that (?). Now, I am unlocked with S-on. I have TWRP available. When I reboot, I am taken to the HTC lock screen, but if I unlock it, I get a white HTC screen that lets me do nothing.
I just want to get it back to what I had when I took it out of the box. If you can walk me though this, I would appreciate it. I am NH if we can do this vocally.
slaldrich said:
I just want to get it back to what I had when I took it out of the box. If you can walk me though this, I would appreciate it. I am NH if we can do this vocally.
Click to expand...
Click to collapse
With s-on, its not possible to use the available ruu. You could use the latest guru reset rom available for your phone. Select the option to wipe, install stock recovery and stock radio.
http://www.htc1guru.com/dld/guru_reset_m7_sprint_3-04-651-2-zip/
alray said:
With s-on, its not possible to use the available ruu. You could use the latest guru reset rom available for your phone. Select the option to wipe, install stock recovery and stock radio.
Is it possible to get my s-off again? If so, how might I do that?
Click to expand...
Click to collapse
slaldrich said:
alray said:
With s-on, its not possible to use the available ruu. You could use the latest guru reset rom available for your phone. Select the option to wipe, install stock recovery and stock radio.
Is it possible to get my s-off again? If so, how might I do that?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2633276
Click to expand...
Click to collapse
alray said:
slaldrich said:
okay, I got s-off. now, how do I downgrade hboot?
or
where do I go from here?
and... I really appreciate this!!
Click to expand...
Click to collapse
Click to expand...
Click to collapse
slaldrich said:
alray said:
slaldrich said:
okay, I got s-off. now, how do I downgrade hboot?
or
where do I go from here?
and... I really appreciate this!!
Click to expand...
Click to collapse
download this ruu.zip http://www.htc1guru.com/dld/ruu-zip-m7_wls_jb_50_sprint_1-29-651-10_ruu_decrypted-zip/
save it in the same folder where adb and fastboot are
reboot your phone in bootloader mode, select fasboot, plug your usb cable.
open your command prompt from fastboot/adb folder
type:
Code:
fastboot oem rebootRUU
(make sure you use capital letter for RUU)
your phone will reboot in ruu mode, a black screen with a silver HTC logo
then type:
Code:
fastboot flash zip <name_of_ruu_you_have_downloaded>.zip (without < and >)
wait for the ruu to flash. It will probably output something like: failed, flush image again so do the same command again
Code:
fastboot flash zip <name_of_ruu_you_have_downloaded>.zip (without < and >)
then
Code:
fastboot reboot
your phone should boot to your stock rom.
Click to expand...
Click to collapse
Click to expand...
Click to collapse
the download link from htcguru is broken... no download available there
Is there anything else I can use? a different link, perhaps?
slaldrich said:
the download link from htcguru is broken... no download available there
Is there anything else I can use? a different link, perhaps?
Click to expand...
Click to collapse
Don't forget to quote me for faster answer
I have just tested the link and it work fine for me, the download speed isn't great atm but you'll be able to get the file in maybe 1 hour (200-300 Kb/sec)
alray said:
Don't forget to quote me for faster answer
I have just tested the link and it work fine for me, the download speed isn't great atm but you'll be able to get the file in maybe 1 hour (200-300 Kb/sec)
Click to expand...
Click to collapse
The download has begun working but all my attempts truncate/stop at around 20MB... Nowhere near 1gb. I will keep trying -- because right now I have an HTC One with working Cyanogenmod... but no connectivity at all with Sprint.
Do you happen to have a copy you can throw in dropbox for me?
And... this is the first time I've ever used these forums, so, I am still learning what I am doing. Thanks for your patience
I did download a rom called
Sprint_HTC_One_3.04.651.2_Stock_Rooted_Odexed.zip
If I flash this, will it fix my radios or will it just put me deeper in the hole?
I am on my 10th try for the htc1guru ... but none has made it past 40mb
alray said:
Don't forget to quote me for faster answer
I have just tested the link and it work fine for me, the download speed isn't great atm but you'll be able to get the file in maybe 1 hour (200-300 Kb/sec)
Click to expand...
Click to collapse
I finally was able to download the entire file. Then, I carefully followed instructions as you sent...
At last step, I received a "failed 32 header error"
so, I repeated the flashboot flash zip command again. same error
repeated a third time. same error
did fastboot reboot and.... nothing still at cyanogenmod with no connectivity. It didn't take.
It went as planned up until the Failed message.
Please tell me you have another idea or a way to deal with this.
alray said:
Don't forget to quote me for faster answer
I have just tested the link and it work fine for me, the download speed isn't great atm but you'll be able to get the file in maybe 1 hour (200-300 Kb/sec)
Click to expand...
Click to collapse
I did finally get the entire file... and did everything you suggested. Unfortunately, I got a Failed remote "32 header error"
I repeated the whole procedure a second time. Still nothing. I checked the MD5 of the file and it apparently was corrupt.
SO... I was back to Cyanogenmod 11 with no Sprint. As a last ditch try before retiring to bed, I came upon a zip file that said it had Sprint radio files. I figured, heck, what have I got to lose? So, I flashed the small zip. and POOF... works! My phone is back AND I didn't have to go back to stock.
I do want to say THANK YOU for all your help. Knowing you were there to help me along encouraged me not to throw my phone under a passing truck. I am sure that once we got that dang file downloaded correctly, it would have worked.
Even though it didn't turn out as we started.... your help was immeasurable for me. Thanks again.
C:\adb>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: N/A
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno: FA34NS902058
(bootloader) imei: 99-------------------1
(bootloader) meid: 99-----------------
(bootloader) product: m7_wls
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0720000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3885mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-1f512bb6
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
after flash custom rom imei & baseband gone plezzzzzz help n i can not flash any RUU or official rom
smrussel said:
C:\adb>fastboot getvar all
(bootloader) version: 0.5
(bootloader) version-bootloader: 1.57.0000
(bootloader) version-baseband: N/A
(bootloader) version-cpld: None
(bootloader) version-microp: None
(bootloader) version-main:
(bootloader) version-misc: PVT SHIP S-OFF
(bootloader) serialno: FA34NS902058
(bootloader) imei: 99-------------------1
(bootloader) meid: 99-----------------
(bootloader) product: m7_wls
(bootloader) platform: HBOOT-8064
(bootloader) modelid: PN0720000
(bootloader) cidnum: 11111111
(bootloader) battery-status: good
(bootloader) battery-voltage: 3885mV
(bootloader) partition-layout: Generic
(bootloader) security: off
(bootloader) build-mode: SHIP
(bootloader) boot-mode: FASTBOOT
(bootloader) commitno-bootloader: dirty-1f512bb6
(bootloader) hbootpreupdate: 11
(bootloader) gencheckpt: 0
all: Done!
after flash custom rom imei & baseband gone plezzzzzz help n i can not flash any RUU or official rom
Click to expand...
Click to collapse
Did you flashed a sprint compatible custom rom? You can't flash custom roms for the M7_UL on your m7_wls, both phones haves different partitions layout. Reflash a sprint custom Ron using a sprint compatible custom recovery or flash the latest sprint ruu from htc website (Google search: htc support rom download).
Sent from my HTC One using XDA Labs
alray said:
Did you flashed a sprint compatible custom rom? You can't flash custom roms for the M7_UL on your m7_wls, both phones haves different partitions layout. Reflash a sprint custom Ron using a sprint compatible custom recovery or flash the latest sprint ruu from htc website (Google search: htc support rom download).
Sent from my HTC One using XDA Labs
Click to expand...
Click to collapse
i tried to flash with sprint Ruu but flash could not complete due to an error

Categories

Resources