Related
I'm not sure if anyone is aware, but the flappy charging port cover is just dust protection cover, it provides no waterproofing. I cut mine off months ago it's very annoying. It does not affect the phone's ability to survive 1 meter of water for 30 minutes.
My phone see's water daily in the shower or going wakesurfing. Still working like brand new since day 1!
I don't know that I'd be willing to risk it. How can something possibly prevent water from entering, but allow dust in? Even if the port is sealed off from the rest of the device (like the headphone port), you have to consider that you are introducing electricity into the environment. Any amount of residual water can and will cause a short.
my-blue-snog-box said:
I don't know that I'd be willing to risk it. How can something possibly prevent water from entering, but allow dust in? Even if the port is sealed off from the rest of the device (like the headphone port), you have to consider that you are introducing electricity into the environment. Any amount of residual water can and will cause a short.
Click to expand...
Click to collapse
It makes sense. Sealing it off to prevent water intrusion w/o the flap seems pretty easy, but to make the port dust proof you'd need the flap (the innards of the phone would be water/dust proof behind the connection port, the flap would be to keep the dust out of the port only)
I won't try it but if you're saying it works for you I'll feel a little better when the wife's port cover rips off...
That's good to know, mine's been getting looser and looser and I've been more worried to go near water since it isn't feeling so tight anymore!
Keep in mind that if you have at&t, this should be covered under the 1 year warranty. You may have to argue a bit with the rep, but I got mine replaced when it pulled off.
As a fixer, I decided to test this theory. My friend's two year old ripped her charge port cover off and wanted me to fix it. I've been looking for the past day, and haven't found anything that is a direct replacement, just filler pieces for generic micro-USB or for the S3 ports (same thing, really).
So I took the phone apart so I could see the inside, and I, using electrical contact cleaner spray so I don't break the phone, barely pulled the trigger so it would dribble down into the port instead of blast everywhere. Well, I saw contact cleaner on the inside of the phone within like 2 seconds.
Conclusion: the charge port is not sealed. It might handle a splash if you let the port dry out, but forget about dunking it.
As a tip, search eBay for "6pcs Micro USB Port Dust Cap Cover for Samsung Galaxy S III S3 GT-I9300 (Black)". That is the title of the listing where I found 6 filler pieces for $5 USD, while the popular link provided in these forums for TOPI Covers (topicovers .com/products/micro-usb-port-cover) sells them at $2 each.
I contacted the support center for the store (Elkjp, a norwegian national store owned the Dixon Group) where I bought my Galaxy S4 Active about the cover for the USB-connector, and got this reply (translated into English):
"According to the manufacturer the USB-connector itself is waterproof without the rubber cover. The robber cover is only for dust protection. Normally the warranty does not cover water damage, but with some products, like you Galaxy S4 Active, we will approve your warranty request if water have penetrated into the phone, as long as it has no other visual damages."
Unsure who the store's support supervisor has contacted for this informastion, might be just a wild quess by the supervisor or Samsung in Norway. The manufacturer warranty in Norway is 2 year for Samsung mobile phones, and national customer warranty/complaints are 5 years for mobile phones, according to Norwegian law.
Clarence_C said:
As a fixer, I decided to test this theory. My friend's two year old ripped her charge port cover off and wanted me to fix it. I've been looking for the past day, and haven't found anything that is a direct replacement, just filler pieces for generic micro-USB or for the S3 ports (same thing, really).
So I took the phone apart so I could see the inside, and I, using electrical contact cleaner spray so I don't break the phone, barely pulled the trigger so it would dribble down into the port instead of blast everywhere. Well, I saw contact cleaner on the inside of the phone within like 2 seconds.
Conclusion: the charge port is not sealed. It might handle a splash if you let the port dry out, but forget about dunking it.
As a tip, search eBay for "6pcs Micro USB Port Dust Cap Cover for Samsung Galaxy S III S3 GT-I9300 (Black)". That is the title of the listing where I found 6 filler pieces for $5 USD, while the popular link provided in these forums for TOPI Covers (topicovers .com/products/micro-usb-port-cover) sells them at $2 each.
Click to expand...
Click to collapse
No offense, but you sound less than scientific and I see numerous holes in your testing. If the device is rated by the manufacturer to be waterproof without the USB flap then it seems unreasonable to question without definitive evidence that it is not, which thus far you have failed to provide.
Sent from my GT-I9295 using XDA Premium HD app
i agree. dont mock if you are no expert!!
The IP67 rating is based upon 1 meter of water depth for 30 minutes without water intrusion. This requires positive sealing methods like the silicone gasket on the cover with snap clips holding it down with pressure. A little flappy cover that just sets in place provides no sealing what so ever at 1.4psi.
pyro254750 said:
No offense, but you sound less than scientific and I see numerous holes in your testing. If the device is rated by the manufacturer to be waterproof without the USB flap then it seems unreasonable to question without definitive evidence that it is not, which thus far you have failed to provide.
Sent from my GT-I9295 using XDA Premium HD app
Click to expand...
Click to collapse
I checked the manual (from Samsung.com) and on page 11 says it's NOT waterproof without the USB cover correctly in place:
"Caution! Be careful not to damage or detach the multipurpose jack cover. A damaged or missing cover can result in water damage to the device."
It may be a CYA note, or maybe it's not water-resistant without the cover. As far as I can find this is the only 'official' word on whether or not it's water-resistant without the flap (which its supposedly not). I'm not doubting the OP by any means, if his phone works without the cover that's great, but I'm not going to rip mine off on purpose to test it out.
TwoStroker37 said:
The IP67 rating is based upon 1 meter of water depth for 30 minutes without water intrusion. This requires positive sealing methods like the silicone gasket on the cover with snap clips holding it down with pressure. A little flappy cover that just sets in place provides no sealing what so ever at 1.4psi.
Click to expand...
Click to collapse
So, a rubber stopper in a sink or bathtub will not seal because the water is only a few inches deep?
In theory, the flap will always seal if it fits well (no dirt, cracks, etc.) and the pressure outside the phone is greater than the pressure inside the phone, but not so great a difference to structurally deform or damage the seal. If the phone remains vertical with the flap at the bottom, it doesn't need the seal at all. Think of an inverted bottle without a cap. You can push it down into the water, but the air remains inside.
Sent from my SAMSUNG-SGH-I537 using Tapatalk
Water proof cover.
If you do not like the dust cover on the phone you can try a piece of silicone ear plugs. The are designed to keep water out of your ears when swimming just don't force it into deep in the usb port. If your still not satisfied and you want to dunk the phone a simple zip lock bag works great for most phone and you can still use the touch screen though it will not be as sensitive. I have used plastic bags to keep my phone dry in the rain several times. Good luck, hope this was helpful.
Yes It is bit worry for me also and my phone is now out of warranty and I can not replace it.
Wadell said:
[/COLOR]The Samsung Galaxy S4 wireless charging kit is now available directly through Samsung’s accessory store. Should you choose to make charging on your GS4 “hassle free,” be prepared to shell out $90. In order to become a wireless charging machine, the Galaxy S4 needs both a charging cover (battery cover replacement) and the charging pad (pictured above). The back cover runs $39.99, while the pad will cost $49.99. If there is one added bonus to the charging pad, it’s the fact that it should work with all Qi-certified wireless charging products, so you could get some additional use out of it.
We’ve got links to Samsung’s site below for those who are interested.
Click to expand...
Click to collapse
Where did you find the original samsung wireless covers?
I cant find them anywhere?
Do you have a link?
BR
The S4 cover is different than the S4 Active for obvious reasons. It won't fit.
my-blue-snog-box said:
Keep in mind that if you have at&t, this should be covered under the 1 year warranty. You may have to argue a bit with the rep, but I got mine replaced when it pulled off.
Click to expand...
Click to collapse
Did they send you the part or did you have to send your phone to them? I don't mind replacing it myself. I ripped mine as well and I also noticed that it isn't as loud with the cover off(noticed that before it ripped off). Either way, I use my phone for work, so I can't be without a phone for weeks while they fix something.
monkeyhouse said:
Did they send you the part or did you have to send your phone to them? I don't mind replacing it myself. I ripped mine as well and I also noticed that it isn't as loud with the cover off(noticed that before it ripped off). Either way, I use my phone for work, so I can't be without a phone for weeks while they fix something.
Click to expand...
Click to collapse
They sent me a replacement, and only once I got that in the mail did I have to send in the defective unit.
Sent from my Nexus 5 using Tapatalk
Confirmed cover not for waterproofing
I wanted to reiterate this statement. I spoke to Samsung technical support today and they confirmed that cover is just a dust cover. It has nothing to do with keeping water out of the phone. Mine broke off and I'm not going to attempt to replace it.
TwoStroker37 said:
I'm not sure if anyone is aware, but the flappy charging port cover is just dust protection cover, it provides no waterproofing. I cut mine off months ago it's very annoying. It does not affect the phone's ability to survive 1 meter of water for 30 minutes.
My phone see's water daily in the shower or going wakesurfing. Still working like brand new since day 1!
Click to expand...
Click to collapse
Im not quite sure that usb port cover flap is only to protect from dust. Then why on every video, instructions, manuals, after unplugging usb cable there is a warning to close usb cover and in camera Aqua Mode too, if not closed properly this situation water will damage phone? I havent heard of wateroroof usb. Every waterproof phone has usb cover that protect usb port. Theres only waterproof headphone jack
Wysłane z mojego GT-I9295 przy użyciu Tapatalka
Has anyone tried or considered applying a tiny bit of silicon grease or something similar to the edges of the waterproof covers/flaps to reinforce the seal? I rarely ever open any of mine since I used bluetooth headphones and the dock connectors for charging. I thought about it because my SIM card flap failed, causing the power button to stop working. I was surprised since I have only ever opened it once.
Any thoughts?
Heinous said:
Has anyone tried or considered applying a tiny bit of silicon grease or something similar to the edges of the waterproof covers/flaps to reinforce the seal? I rarely ever open any of mine since I used bluetooth headphones and the dock connectors for charging. I thought about it because my SIM card flap failed, causing the power button to stop working. I was surprised since I have only ever opened it once.
Any thoughts?
Click to expand...
Click to collapse
I would agree with you. But you have to be careful what "grease" you spply, some will perish the rubber and others will cause it to swell.
defsix said:
I would agree with you. But you have to be careful what "grease" you spply, some will perish the rubber and others will cause it to swell.
Click to expand...
Click to collapse
I have some gasket/o-ring grease for a waterproof camera case that might work.
Heinous said:
I have some gasket/o-ring grease for a waterproof camera case that might work.
Click to expand...
Click to collapse
Yes, something like that would work. I've had no problem with my seals, but I check them weekly and give them a gentle wipe with a damp cloth.
I broke off the USB port cover and the little bobble off the flap is still stuck inside the handset. I've tried digging with a pin but can't get it out.
What's the best thing to do?
Remove the rear cover?
"If it's broke, use a hammer. If that fails, you're not using a big enough hammer."
Sorry i had too
also try needle nose tweezers
but if you play on replacing them yourself, i think you would have to open the back aither way
Kirkymole said:
I broke off the USB port cover and the little bobble off the flap is still stuck inside the handset. I've tried digging with a pin but can't get it out.
What's the best thing to do?
Remove the rear cover?
Click to expand...
Click to collapse
As murphyslaw just said use very slim tweezers, or something to hook the rubber feet and pull it out, there are videos on youtube for this.
Kirkymole said:
I broke off the USB port cover and the little bobble off the flap is still stuck inside the handset. I've tried digging with a pin but can't get it out.
What's the best thing to do?
Remove the rear cover?
Click to expand...
Click to collapse
Don't remove the rear cover. All spare parts of Xperia Z1 are glued together tightly. It is very hard to separate them.
There is no guarantee that you can keep the waterproof as before.
Install a new one directly if the bit dose not interfere.
If you must need to dig it out, needle or pin and patience is what you need.
LotoTutu said:
Don't remove the rear cover. All spare parts of Xperia Z1 are glued together tightly. It is very hard to separate them.
There is no guarantee that you can keep the waterproof as before.
Install a new one directly if the bit dose not interfere.
If you must need to dig it out, needle or pin and patience is what you need.
Click to expand...
Click to collapse
I got no problems with the waterproofing side, we have more waterproof products than Sony could ever get their hands on at work lol
Hi guys, i guess the title especifies what happened, haha. Well, my xperia Z felt down in water with the fone jack open, water got all inside it. I turned it off, and then i sleept, well, i wake, he was on, the funny thing is that the alarm was working, but first i had problems to stop it, since touch wasnt working neither the buttons. Seconds after, its screen turned black, and it just vibrate, then, hours after he went down, since that, whenever i turn it on, he just blink the red led three times, and nothing.
What you guys think it is?
nanhuto said:
Hi guys, i guess the title especifies what happened, haha. Well, my xperia Z felt down in water with the fone jack open, water got all inside it. I turned it off, and then i sleept, well, i wake, he was on, the funny thing is that the alarm was working, but first i had problems to stop it, since touch wasnt working neither the buttons. Seconds after, its screen turned black, and it just vibrate, then, hours after he went down, since that, whenever i turn it on, he just blink the red led three times, and nothing.
What you guys think it is?
Click to expand...
Click to collapse
When the red led blinks it would be a softbrick...But as you said you have water damaged ur phone..., this is a hardware issue.... So kindly get it repaired from a service center before it's totally dead...
Mine is totally dead. I rode home (pushbike) in an absolute downpour last night, and although the flaps were all closed, it got filled with water and won't even power on.
Inspecting it with a magnifying glass it looks like the USB flap rubber is broken.
I really do hate the poor design of the flaps on the XZ. I am glad they redesigned them later.
My question is, is it worth (as a handy person) opening it up, drying everything out, or is it likely something would have physically died/burnt out?
Mobe1969 said:
Mine is totally dead. I rode home (pushbike) in an absolute downpour last night, and although the flaps were all closed, it got filled with water and won't even power on.
Inspecting it with a magnifying glass it looks like the USB flap rubber is broken.
I really do hate the poor design of the flaps on the XZ. I am glad they redesigned them later.
My question is, is it worth (as a handy person) opening it up, drying everything out, or is it likely something would have physically died/burnt out?
Click to expand...
Click to collapse
It's not a bad design of usb flaps trust me...just see the design of Samsung waterproof phone s...that's called bad design...
Every material has limitations.. So if you use flaps the more..it loses its tightness or quality... That's why Sony offer a Dock for charging... So the Waterproofness remains maintain...
But now sony has changed its design.. In Xperia m4 aqua... There's no flap on charging.. And it's still waterproof.... SO NO NEED TO BUY dock....
Well for ur question u must give a try to open the phone nd dry it with hair dryer.. .if water doesn't damage any circuit it may wake up.... For opening phone hot air gun is used..
If you can't do it urself..give it to a professional or service centre...
Hope this helps...
DastanShaikh said:
It's not a bad design of usb flaps trust me...just see the design of Samsung waterproof phone s...that's called bad design...
Every material has limitations.. So if you use flaps the more..it loses its tightness or quality... That's why Sony offer a Dock for charging... So the Waterproofness remains maintain...
But now sony has changed its design.. In Xperia m4 aqua... There's no flap on charging.. And it's still waterproof.... SO NO NEED TO BUY dock....
Well for ur question u must give a try to open the phone nd dry it with hair dryer.. .if water doesn't damage any circuit it may wake up.... For opening phone hot air gun is used..
If you can't do it urself..give it to a professional or service centre...
Hope this helps...
Click to expand...
Click to collapse
Thanks. No, it was unrecoverable by me...
I did get a Z3. The flaps are so much better designed than the original z I find. The fact the pull straight out and can rotate.
I definitely agree having the USB charge port just waterproof is a great idea. I am glad at least the headphone port is now on the Z3. I remember in this forum or another when the z came out I was saying how easy it would be to make a headphone port waterproof. Just a solid piece of plastic injection moulded around the pin contacts. Same would apply to the micro usb too I guess.
Mobe1969 said:
Thanks. No, it was unrecoverable by me...
I did get a Z3. The flaps are so much better designed than the original z I find. The fact the pull straight out and can rotate.
I definitely agree having the USB charge port just waterproof is a great idea. I am glad at least the headphone port is now on the Z3. I remember in this forum or another when the z came out I was saying how easy it would be to make a headphone port waterproof. Just a solid piece of plastic injection moulded around the pin contacts. Same would apply to the micro usb too I guess.
Click to expand...
Click to collapse
Yes...same technology of sound port...But it's great.. Idea..to have waterproof charge port.. Cause it have to send the power... Not only the data..
it is a great improvement over previous one... HOPE Sony will do same thing.. In all new waterproof devices
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Droidriven said:
I'll bet you can find a video on YouTube explaining how to disassemble your device.
I DO NOT PROVIDE HELP IN PM, KEEP IT IN THE THREADS WHERE EVERYONE CAN SHARE
Click to expand...
Click to collapse
Already search extensively, no luck so far. Prefer not to 'experiment' and wreck the thing!
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Bro check YouTube very well... it there
Sent from my iPhone using Tapatalk Pro
I can help you.
kiwironnie said:
Need to disassemble my Doogee Y6 (not Y6 Max) to replace the USB port.
If anybody has successfully removed the back, some brief instructions would be really appreciated.
Best wishes, Ron.
Click to expand...
Click to collapse
Did u fix it? I can help you. I opened the phone like 10+ times.
Hi, I have the same problem, I need to open the phone to replace the camera but did not manage to find anything on youtube. Would u please help me? Thanks
Monster 00 said:
Did u fix it? I can help you. I opened the phone like 10+ times.
Click to expand...
Click to collapse
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
kiwironnie said:
Sorry for the later reply Monster. Thought this thread had gone dead!
If you've got some tips about how to open the case without destroying it that would be really helpful.
There's a few videos etc on opening Doogees around (Y6 Max etc) but none that I've found for the Y6, which is quite a different case.
Cheers, Ron
Click to expand...
Click to collapse
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Monster 00 said:
So to start take a flat screwdriver. You may turn off the phone it's not necessary. Remove the sim tray. To open the phone read carefully. Don't try to remove the back metal plate, you're doing it all wrong. There is a plastic surround that meets with the glass. You need to insert your flat screwdriver in the corner(I prefer bottom right) of the plastic case/surround and the phone screen must be facing you. Now there is a super thin black plastic that separate the glass and the surround, you need to put your screwdriver between the thin black plastic and the surround (mine is gold). The plastic will wear a little bit but if you do it properly, you won't notice any scratch or paint damage. Put your screwdriver in and pull it apart trying to lift the back cover. Don't be scared but be careful, go until you hear a click then you may use your finger nail or the screwdriver and pass it all around the phone. You will hear many clicks. Don't be scared for the fingerprint sensor because it is stick to the phone. After having done that for the first time you will be able to open the phone like previous phones used to be, that is removing it like a removable back cover using your fingernails. I hope I could do a video. Tell me if you did not understand a thing because I can use my phone only on Saturday and Sunday( exams are near).
Click to expand...
Click to collapse
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
kiwironnie said:
Brilliant! Thanks Monster. For me you provide a remarkably clear explanation. Used a very small, flat bladed jewellers screwdriver to lever the black plastic surround away until it clicked, just as you describe, then used an old credit card as a helper, to slide along the gap, to separate the metal back from the rest of the phone. Now just need to figure out how to actually make the repair!
Very best of luck with your exams. (so glad to be largely done with such things!)
Best wishes, Ron.
Click to expand...
Click to collapse
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Monster 00 said:
I was about to make a video to help you. I'm glad you succeeded to open the phone. Now tell me what do you need to repair.
Click to expand...
Click to collapse
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
kiwironnie said:
A video would no doubt be tremendously helpful to others anyway.
The problem with the phone is the micro USB socket is stuffed. The plug is loose and difficult to get a connection, due to continual pushing on it by the USB cover flap on the flexible plastic case that came with the phone. Have cut the flap off but the damage has been done (warning to others!).
At first glance it looks like the circuit board will have to come out to have any reasonable chance of de-soldering the socket.
Cheers Ron.
Click to expand...
Click to collapse
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Monster 00 said:
I would prefer replacing the charging board itself. Changing the USB connector seems difficult for me. I can do a teardown video but the problem is the camera. I only have a Samsung galaxy core to make video as I can't take the y6 itself to make a video. The galaxy core does not support focusing while filming and the videos turn out blurry.
Click to expand...
Click to collapse
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
kiwironnie said:
Great advice, makes sense. I now see that it is a separate board and that there are several sellers of Doogee Y6 charging boards. So the plan now is to purchase and try to replace the board, perhaps also replacing the USB connector on the old board as a spare.
Do you know if the ribbon cable(s) have a lock, or does it just pull out? Although a video would have been great, some basic advice on removing the board could be a life saver.
Click to expand...
Click to collapse
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Monster 00 said:
I'll try my best to make a video as I can't do it in front of my parents and as I told you I can only get the phone Saturday and Sunday. Today is Sunday, I'll try my best to help you. If I can't make a video then I'll post the instructions here. I forgot if it has a lock or not.
Click to expand...
Click to collapse
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
kiwironnie said:
Thanks again Monster. The part's on order now now. So whatever you manage will be really appreciated. No rush as it's coming from China, at least a couple of weeks away. Cheers Ron.
Click to expand...
Click to collapse
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Monster 00 said:
Hey I opened the phone and checked the flex cable. It has a lock hidden under some cover, cloth like material. I'm sorry it I won't be able to do a video because it is super blurry. Now that u know how to open the phone you have to unscrew 4 screws at the bottom. After that gently lift the plastic cover because you may damage the speaker and/or the vibrator. You will see the speaker is actually low quality. As for the charging board, it's pretty easy to remove. Once you remove the plastic cover open the lock by gentle lifting the flap and disconnect the cable. I think that you will need to remove the battery too because the cable is too short and maybe be tricky for you to remove it. You must be really carefully when removing the battery. Take a flat object( I used the same flat screwdriver) and try to lift the battery. Make sure not to puncture it. There's a lot of glue underneath. When you remove the battery then it will be easy to remove the cable. There is two clips holding the board in place and you will need to move one of them to take out the board. Mime is a bit damaged but it's OK. The plastic cover protects it. Don't hesistate to ask questions if you don't understand. Thanks.
Click to expand...
Click to collapse
Brilliant, thanks again! No need for a video, as your explanation is very clear and should be obvious to others after they get the back off the phone. Having recently removed a glued battery from a Kindle, it was a hell of an arm wrestle! Hopefully it will be a bit easier with the Y6. I have a flat nylon spudger with a rounded edge, which should be able to lift the battery without puncturing it. Upgrading the speaker at the same time could be a useful hack, if a better one can be found that fits. Although don't know if the impedance is the same for most phone speakers.
Will post results here including any lessons learnt. Cheers Ron.
The replacement usb charge board arrived, purchased from this guy: http://www.ebay.com/itm/New-Origina...e=STRK:MEBIDX:IT&_trksid=p2057872.m2749.l2649 Posting the url as the service was excellent. Very well packed in its own cardboard box and sent by registered post. So I would buy from him again, even if he is a little more expensive than some on AliExpress.
To fit the new board, the case was opened, as described above and the battery removed. To remove the battery, two screws need to be removed from a metal plate covering the battery connector. The battery ribbon cable connector can then be levered up with a small flat screwdriver blade. It's a effectively a plug with a push fit onto the connector so just pops off.
To remove the battery I used an old credit card, sliding it underneath at one edge of the battery, then gently pushing it forward to release the battery bit by bit, from it being glued to the base. This shouldn't need a lot of force and it is important to avoid snagging the ribbon cable that runs under the battery.
The black plastic cover that houses the speaker and covers the charging board was then removed by unscrewing 4 screws. On my phone one screw had a white plastic covering, into which a cross head jewellers screwdriver can be pushed to grip the screw. The charger board was then exposed and the two speaker wires and two wires from the vibrator were unsoldered using a fine tip iron. The plastic cover was then fully removed. The black rubber tape covering the ribbon cable connector was scraped away, the connector unlocked and the ribbon cable removed. The antenna connector attached to the charger board was then levered off using a small flat bladed screwdriver. The charger board itself was then pulled out. It is held in place by tiny plastic tabs on either side and was a bit of a fiddle to remove.
The old charger board has some Kapton or similar tape underneath, which the new board didn't have. So I applied some similar tape to the new board, but this may not be essential. The new board was then fitted back in, again a bit of a fiddle. I found the best way was was to insert the right hand side of the board first under its tab (looking at the inside of the phone from the charger end), with the board rotated slightly anti clockwise, then pushing the left hand side forward (rotating clockwise) and under the left hand tab so that it effectively clicks into place (not much of a click). The rest of assembly was the reverse of disassembly. Soldering the 4 wires (polarity is marked on the board), pushing the ribbon cable squarely into the connector and locking it. Nearly forgot to push the antenna connector back on!
Replaced the back and the new charge board worked perfectly. What a relief! Thanks again to Monster for getting me started. Cheers Ron.
Hello everyone,
I have every tool needed to fix any problems on any mobile phones. But after fixing my y6, I have thought that a T5S would be piece of cake. But it's not.
Any ideas if I can just remove the broken digitizer to attach the new one or is it glued to the LCD like all new Samsung models?