Related
I recently found out I could update my captivate with Kies Mini. I updated and everything went smoothly. Kies told me update was successful and I unplugged my captivate. It was booting up fine until it reached the Galaxy S logo. It kept going through the logo animation for about 2 minutes before it shut off. I took the battery out and tried again. Same result. my soft buttons are lighted up. When I touch them It responds with a blink, but no haptic feedback. What is going on??How can I fix this? I tried using Odin to flash it back to stock but it won't recognize it. Mt phone was stock 2.1 with the Voodoo Lag Fix installed and everything ran fine and then after the JH7 update the phone messed up. I read that Launcher Pro causes problems with this update and you have to select the Touch Wiz UI when doing it which I forgot to do.
Please help, thank you.
this post is just as dumb/wrong as your post in atinm's thread
a) you can't be stock if you have voodoo, voodoo replaces a kernel
b) you aren't bricked because you can get to the galaxy s screen, brick means your phone won't even turn on
c) this isn't development related, general or Q&A
d) if you don't know how to use odin one-click, I'm not going to help you, you put yourself in this situation
Kaik541 said:
this post is just as dumb/wrong as your post in atinm's thread
a) you can't be stock if you have voodoo, voodoo replaces a kernel
b) you aren't bricked because you can get to the galaxy s screen, brick means your phone won't even turn on
c) this isn't development related, general or Q&A
d) if you don't know how to use odin one-click, I'm not going to help you, you put yourself in this situation
Click to expand...
Click to collapse
You rock man! Thanks for the help
I also just noticed something in your post about having LauncherPro turned on.
Kies to my knowledge won't even recognize the phone unless you're on TouchWiz UI.
teranoid said:
I also just noticed something in your post about having LauncherPro turned on.
Kies to my knowledge won't even recognize the phone unless you're on TouchWiz UI.
Click to expand...
Click to collapse
It recognized it and said it said completed. Now I am trying to use Odin and I can get the phone to recognize the phone and I click Start and it says fail and this at the bottom:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005>
<OSM> All threads completed. (succeed 0 / failed 1)
what does this have to do with development, again?
jatkins09 said:
what does this have to do with development, again?
Click to expand...
Click to collapse
Ok, I put it in the Captivate Q/A section...let's see if someone can help me fix the issue.
i have had the same problem in the past and i was able to fix this by wiping the cache partition
Hallo,
sorry for my bad English. I have translate my Problem with promt . I have flash my Tab with JM6. After the flash my Tab do not boot. On the tab is a picture, a yellow triangle and a PC are indicated. Get with Odin 3 1.7 following error message.
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> zImage
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Have you tried recovery
Sent from my GT-I9000 using XDA App
thank you for your answer.
no, what must i do?
wheel14 said:
nothing functions. Over and over again mistake with Odin. I hope you can help me.
Click to expand...
Click to collapse
after you're flashing with Odin, then restating automatic in download mode, press the power button for 10 seconds (until tab will switch off), then restart by pressing the power button together with volume up. wait until finishing installing of CSC and then will restart by it self.
check my tread
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
wheel14 said:
sorry, but it dons´t work. I have this error....
http://forum.xda-developers.com/showthread.php?t=888071
Click to expand...
Click to collapse
I had the same situation, just take a look here. try to don't panic... try to follow my steps described in the tread and you might be succeed. I hope it help
I do not look though there sorry. I am in panic..which step....is the right?
i have flash the pit-file only. ist this right? and now?
wheel14 said:
I do not look though there sorry. I am in panic..which step....is the right?
Click to expand...
Click to collapse
try to look here and here
thank you.. I have flah the pit File only. now i will flash the pda without the pit. re-partition will be not selected. is this right. thank you for your help
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
wheel14 said:
hallo, the flash is ok. but after he will not finalize the installation of CSC and PDA after restart with recovery modus.
Click to expand...
Click to collapse
I can't get you....can you describe a little what have you done? you're saying that you flash the firmware with Odin, right? and then? have you restarted in recovery mode? or you boot the phone loading the OS.....you should restart directly in recovery mode in order to finalize the installation of PDA and CSC....
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
wheel14 said:
Good Morning,
after flash from JMD and Pit i am flash the dbdata. At now the Tab works greatly. Thank you for your help.
Click to expand...
Click to collapse
Welcome back in our family.
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Go to samfirmware.com download the files for your device.
Select pit file then check repartition - flash
Select pda csc modem, uncheck repartition - flash.
Good luck! If you get any trouble send me a msg. on skype luc_de_mar
khatypically said:
I bought a New Samsung Galaxy TAB, just two days back, from Amazon.com and was shipped to Washington DC. It's an unlocked version that has no Operator logos on it. It was indeed an awesome thing until I used my magic hands on it only 15 hours after I received.
I had a problem with Arabic Characters; they were disconnected and sometimes reversed. So, I searched over the net for one day and chose to install a ROM from Samfirmware.com. I chose the latest firmware from the table of arabic firmwares. It's P1000JPJM5. (P1000JPJM5 ## P1.PIT Version 2.2 2011 January), so here are the steps that I've gone through:
1. Download the firmware.
2. I use the Odin 1.7 and applied the PIT file first. It finished successfully in 11 seconds.
3. I put the Galaxy tab in the Download mode (decrease volume + Power).
4. I applied the PDA using the Odin 1.7, I chose the TAR file that came with the P1000JPJM5 downloaded file.
5. A light blue indicator started just below the Download logo, the indicator progressed cheerfully, but suddenly stopped. I checked the Odin, and found a "FAILED!" sign. I searched the log, and found the following error:
<ID:0/045> cashe.rfs
<ID:0/045> Modem.bin
<ID:0/045> Complete(Write) Operation failed
<ID:0/045> All threads completed. (Succeed 0/ Failed 1)
attached is a jpg file having the error exactly.
6. Regardless of the warning saying "Don't unplug the target" or whatever it said by that time, and since the application of the firmware stopped, I unplugged the USB cable. I did that after waiting for 20 minutes whereas the Galaxy Tab didn't show any response but that download logo and the non-moving indicator.
7. After I did that, the Galaxy Tab became dead. Whenever I attach it to the computer, it displays a 3 icons screen; a computer, a phone, and a warning triangle with an exclamation mark. I assume that this means that there is an error in the connection between the Tab and the computer.
8. No matter how many times I tried the Download, recovery or any other thing, the phone would only display one of two things, the 3 icons screen that I listed in the previous step, or the Battery screen showing a grey battery.
HELLLLLP!!!!
Regards,
Khatypically.
Click to expand...
Click to collapse
Sent from my GT-P1000 using XDA App
Thanks Lucian, This is exactly what I did in the first place. Used Odin 1.7 and applied the PIT file coming with it, then applied the P1000JPJM5 PDA and CSC modem file.
Unless the P1000JPJM5 is not for my device?? How to know?
Lucian, any clue?
My tab is dead after I tried to install an arabic firmware from samfirware.com. I bought my tab originally from the US. Now, I'll download the "suitable" firmware from samfirmware.com as you advised, but How would I ever know the suitable firmware given that my device is exactly this one (that's where I bought)(my devise is dead now and can only display the download mode):
www .amazon. com /GALAXY-TAB-P1000-16GB-UNLOCKED/ dp /B004AKOVIS/ ref=sr_1_1?ie=UTF8&s=electronics&qid=1305378100&sr=8-1
Regards,
Khatypically, alive with a zoombie tab
totally unresponsive tab
I have been searching around forums looking for advice and have been unable to locate a solution so here seems as good a place as any to ask for help. I have an unlocked gtp-1000 that has been running overcome 1.4.5 for last month very nicely until tonight when I thought it would be a good idea to get some gingerbread goodness like I have been using on my nexus one. was going to flash Overcome ROM v2.0.0 BETA 2 and was following guide but only got halfway through flashing stock gingerbread with odin when laptop unexpectedly did a restart for an unknown reason while I was away getting a snack. was unsure whether flashing process had been completed so opened odin again and tried reflashing. couldnt get past
setup connection...
so tried to reboot into download mode and then powered down. now tab is dead. battery was at 80% when it died
before I take back to samsung tomorrow any ideas?
I have plugged into wall charger= nothing
plugged into laptop=nothing and not detected
held power and volume up=nothing
held power and volume down=nothing
held power and volume up & home=nothing
no sounds or anything at all on screen
truly bricked?
Updates:
Hi Guys,
I applied the p1000nubjm2 firmware. I downloaded it from samfirmware. It's the latest P1000L firmware for America/Australia. It failed in the PDA file: P1000NUBJM2_P1000NUBJM2_P1000NUUBJM2_HOME.TAR . I was planning to apply the gingerbread update after that.
Now to the results, As you know, before, I was able to reach the download mode, the startup Galaxy Tab/Samsung screen, and the battery displays when connecting the cable. Now, after application of this lovely firmware and failure, nothing (literally "Nothing") takes place. The device became more dead than it was before . It doesn't display anything and it doesn't respond to power or displays the battery. It became a black $500 cost brick No matter how much time I keep it charging (or what "should be" charging), it would never startup again (sigh!) The ODIN and samsung kies no more recognize the device when connected to the computer.
Any additional clues before I decide to convert it to a teacup base?
Regards,
ARK
hi fellow devs. from the galaxy tab community,
i have come to a very difficult situation for flashing and this just went completely wrong. let me describe:
i wanted to flash a cm10 nightly to my galaxy tab p1000n, i didnt realize i had flashed the wrong version which was cm10 nightly for p1000.
at this point the touchscreen had no response over the software. blue cwm was installed correctly.
so i tried to reflash the correct p1000n cm10 nightly, but i was unable to do it, the android kept dying, and installation never happened.
tried PA ROM same problem, the android kept dying not being able to update from zip.
so i tried to bring back to stock.
used the overcome method listed in q&a thread
flashed wrong files apparently once again thinking that these was going to help.
everyting in ODIN went well got the GREEN PASS!
after that my tab didnt reboot. all i get is the lights on touch capactive buttons, black screen.
ODIN still recognizes the TAB i get the yellow box 0:[COM5]
although whatever I try to flash i get this message:
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
after this msj, nothing happens.
this has been very frustrating, I never thought it would get to ths point, ive been reading for about 4 hours, and nothing seems to be clear enough, to the point that I dont know If theres a solution to my problem. I would appreciate help from you guys.
i think Heimdall could be the best bet although its still not very clear ho to fix this problem. my question to you guys if theres a specific series of steps to really fix this problem? without getting to point to completely kiling it, this TAB is not mine thats the worse of it. i have experience using both flashing methods, heimdall super one click and ODIN with my infuse 4g. if anyone could provide me with the necessary files to repair the P1000N, that would be much appreciated, if anyone could guide me would me much better, thanks in advance, i just hope to find a solution to this mess.:crying:
hi there..
since i bought my phone it never got a firmware update, neither OTA nor a manual one. It came and stayed with android 2.2 with all these years.
Now that i am more into android i decided to use a custom rom, this one = http://forum.xda-developers.com/showthread.php?t=2012061
But before flashing this rom i had to flash it with an official 2.3 rom, since it was one of the requirements and it still had a 2.2 in it.
I went to samobile, grabbed this rom http://www.sammobile.com/firmwares/3/?download=4340, plus a .PIT that was necessary according to the tutorial i was following.. and on the first attempt i got the error and the device got bricked.. So i tried, and tried, and tried... but i always end up getting the same error within Odin. This one:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> __Xmit Write fail
<ID:0/004> XmitData Fail..
<ID:0/004> Complete(Write) operation failed.
The device is now bricked, i can't even enter in downloadmode anymore, so i bought a USBJIG to enter in downloadmode and it works, but i still get the same error when trying to flash. I've tried dozens of different roms (of course all of them were made for this device), different versions of Odin, different USB port, Samsung Kies is installed but it is completely closed. I don't know what else to do, i need help... Please help?
xcaninox said:
I've tried dozens of different roms (of course all of them were made for this device), different versions of Odin, different USB port, Samsung Kies is installed but it is completely closed. I don't know what else to do, i need help... Please help?
Click to expand...
Click to collapse
you cannot use i9000 ROM's only i9000B ROM's, you need to kill KIES , Open task manager and close these : Kies.exe , KiesTrayAgent.exe, and KiesPDLR.exe
preferably use Odin 1.85 or 3.04
FIRST STEP for ALL Problems:-
Whenever you have a problem with your Phone, power it down, remove battery, remove SIM card and Ext SD card and press and hold your power button for at least 30 seconds to a min, before reinserting battery and trying any solution
First reboot PC after a power cord unplug and also reboot the Phone after a battery pull. Always use a Fresh Odin after any attempt to flash, than make sure you "Uncheck Repartition", If you had checked it or clicked PIT when you are not using one. You should also be running Odin as an Admin and ensure that KIES is not running when using Odin. Most of all, only use Samsung USB cable and not others as they may be incompatible and trying it out on a lap top or another PC ( when it happens repeatedly)
i discovered what was causing the error. it was Windows 8, samsung drivers are not working correctly on it, i don't know if this is a localized or a global problem... my guess is it is a global one
i had Kies installed in windows 8,and all its process were killed before flashing pretty much on all of the time i was trying to flash.
yesteday by pure luck my sister came to my house for a visit, and she had hers notebook with her that btw has windows7, so i decided to try flashing the phone through it, i grabbed it installed samsung drivers and didn't install Kies, surprisingly, for me at least, the flashing went perfectly OK on the first attempt.
after the flash i had one error, "couldn't mount db/data", i googled it and easily fixed it already, but that is another thing for another thread.
thank you for helping
xcaninox said:
i discovered what was causing the error. it was Windows 8, samsung drivers are not working correctly on it, i don't know if this is a localized or a global problem... my guess is it is a global one
Click to expand...
Click to collapse
All PC's running any version of windows seem to get USB connection problems at one time or the other But lap tops and notebooks seldom have this problem.
Hey guys, what exactly should I do to try out the new tizen operation system on my gg1? Is there a tutorial on how to do this or something?
scheirere said:
Hey guys, what exactly should I do to try out the new tizen operation system on my gg1? Is there a tutorial on how to do this or something?
Click to expand...
Click to collapse
reflash your stock countries firmware
then in kies you can upgrade to tizen
This is what I did to my gear with Null 23:
1. download and extract Tizen firmware for my country, Canada in my case.
2. place my gear in download mode
3. start ODIN 3.09, load the Tizen firmware in the AP tab
4. connect my gear to computer, allow ODIN to recognize the gear
5. Click the Start button in ODIN, wait about 2 min. while this is happening, uninstall gear manager on my DN3 V4 beta2 note 2, restart phone, and install gear manager from Samsung stores
6. Once the ODIN finishes flashing, the gear restarts, and my note 2 recognizes the gear right away, and I was able to setup everything like before on android, with all the notifications and weather.
So in my flashing, I did not return the gear to stock android before flashing Tizen, and I did not have any of the flashing or connection issues that others have faced. Not sure why this is the case, but I am not going to find out.
In any case, one thing to keep in mind, flashing Tizen is a one way street, currently there is no way going back to android if you change your mind after flashing, so make sure you think really hard and decide.
scheirere said:
Hey guys, what exactly should I do to try out the new tizen operation system on my gg1? Is there a tutorial on how to do this or something?
Click to expand...
Click to collapse
there's a thread in the general section about tizen for the gg1.
i believe you turn on usb debugging, boot to download mode and connect to kies. if it doesn't say there is an update available, then the thread in general has a link to the tar to flash it through odin and directions to do the same. there is a search function to deliver this information, i just learned this earlier today through the search function.
What region should I pick for the firmware? I didn't see any listed for the US?
scheirere said:
What region should I pick for the firmware? I didn't see any listed for the US?
Click to expand...
Click to collapse
I picked Canadian.
Hmm....I tried both canada and the UK. Both installed without incident and I can connect thru my phones bluetooth menu. But gear manager doesn't connect. It sits at the screen showing "Connecting to Gear". Any thoughts or ideas? I'm pretty sure it's something in this galaxy gear as my wifes gear (with null 23 ROM) connects just fine.
stuck
So far no issues except no watch styler or multi watch in gear manager
Update got watch styler to work
Muti watch still says not connected
Ultraman666 said:
So far no issues except no watch styler or multi watch in gear manager
Update got watch styler to work
Muti watch still says not connected
Click to expand...
Click to collapse
What firmware did you flash? Canadian region?
Also, I can't get the gear to work with kies. It recognizes the gear but then gives me a message saying kies can't update the firmware. WTF?? This is really aggrivating!
scheirere said:
What firmware did you flash? Canadian region?
Click to expand...
Click to collapse
Btu for Great Britain using odin
Sent from this Pure Evil Wicked!!!
Trying to Flash Tizen with Odin and no luck so far. Every time odin gets stuck on boot loader. I have tried downloading MD5 file from my region(Canadian) off of two different sites. Also I am back to stock rom now and still no luck with odin or kies. Having an issue connecting to Kies 3 and Kies 2.6. Both will not connect to gear watch in download mode and just powered on. Every time Odin flashed Tizen gear is soft bricked and I have to re flash TWRP to bring it back to life.
Anyone else having these issues or have any fixes ?
Much Appreciated :good:
timzorr said:
Trying to Flash Tizen with Odin and no luck so far. Every time odin gets stuck on boot loader. I have tried downloading MD5 file from my region(Canadian) off of two different sites. Also I am back to stock rom now and still no luck with odin or kies. Having an issue connecting to Kies 3 and Kies 2.6. Both will not connect to gear watch in download mode and just powered on. Every time Odin flashed Tizen gear is soft bricked and I have to re flash TWRP to bring it back to life.
Anyone else having these issues or have any fixes ?
Much Appreciated :good:
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?p=53630254
PLEZE HELP! Stuck in Odin!
OK, I'm buggered. I've been resisting "upgrading" to Tizen for months, partly because I was happy with my Null setup, and partly because I'm a noob and was afraid I'd screw it up. Finally, after weeks of no more rich notifications thanks to a Gear manager upgrade, I read as much as I could absorb and took the plunge. And now I've screwed up.
In short, I'm stuck in Odin 3.09 at this point in the sequence:
<ID:0/011> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> V700XXUCNF1_V700OXACNF1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/011> Odin v.3 engine (ID:11)..
<ID:0/011> File analysis..
<ID:0/011> SetupConnection..
<ID:0/011> Initialzation..
<ID:0/011> Get PIT for mapping..
<ID:0/011> Firmware update start..
<ID:0/011> SingleDownload.
<ID:0/011> sboot.bin
Now, this is farther than I'd managed yesterday, when it would simply get to SetupConnection, freeze for 4 minutes, and report FAILED. But now it's not reporting anything, it's been hanging for close to an hour and I don't know what to do, and am worried that if I pull the plug I will just brick the watch (Odin doesn't appear to have a "Cancel" mechanism that isn't greyed out when running).
Finally, I should mention that I followed the steps as described earlier in this thread by "bballengphd", and went into download mode directly from my Null watch without re-flashing stock Android. And while I get the little green robot with the "Downloading... do not turn off target!!" message, I have never seen the watch show a status bar.
Help?
Never mind
I worked it out. Actually wound up bricking the watch, and then found this gem in another thread:
http://forum.xda-developers.com/showpost.php?p=56827616&postcount=26
... and it totally worked. Koxfi, you saved my bacon.