Database Develop

My xperia z thinks it's Galaxy Nexus

Hi guys, i bought phone off ebay and under model number it says: "Galaxy Nexus". Everything works fine, it has all Sony features and is definitely not a galaxy nexus .
I know i need root to change build.prop, but i can't achieve it since doomlord's tool says galaxy nexus is not supported. (it's 6602 on 10.3.A.0.423 firmware btw)
Here's what it says:
Device detected: Galaxy Nexus (10.3.A.0.423)
Galaxy Nexus (10.3.A.0.423) is not supported.
You need to manage to get remap_pfn_range addresses.
Click to expand...
Click to collapse
Unlocking bootloader and reflashing tft is not an option for me, since i still want to preserve TA partition.
P.S.
doomlord if by any chance you're reading this, can you please add exception to your tool for it to accept Galaxy Nexus (10.3.A.0.423) and send it to me?

Try to reflash the firmware with flashtool.

I'm trying to do that, but phone restarts in about 20 seconds when it's in flashmode.
Flashtool is still unpacking firmware when phone already reboot by itself. I have all drivers installed correctly and am using windows 8.
Maybe that's the problem?

Nikoloz17 said:
I'm trying to do that, but phone restarts in about 20 seconds when it's in flashmode.
Flashtool is still unpacking firmware when phone already reboot by itself. I have all drivers installed correctly and am using windows 8.
Maybe that's the problem?
Click to expand...
Click to collapse
I'm not sure if u r doing this, but connect the phone only when the pop-up appears asking you to "Connect your phone in Flashmode" i.e. Phone switched off ,Volume Down button & then connect the USB.

I'm doing that, but it still restarts by itself after a while
03/037/2013 23:37:47 - INFO - <- This level is successfully initialized
03/037/2013 23:37:47 - INFO - Flashtool Version 0.9.10.2beta6 built on 2013-04-21 22:23:00
03/037/2013 23:37:52 - INFO - Device disconnected
03/038/2013 23:38:01 - INFO - Selected sony xperia z / 10.3.A.0.423 / C6602
03/038/2013 23:38:02 - INFO - Preparing files for flashing
03/039/2013 23:39:16 - INFO - Please connect your device into flashmode.
03/039/2013 23:39:22 - INFO - Device connected in flash mode
03/040/2013 23:40:23 - INFO - Device disconnected
Click to expand...
Click to collapse

Nikoloz17 said:
I'm doing that, but it still restarts by itself after a while
Click to expand...
Click to collapse
Instead of a normal power off,try a hard reset i.e. Hold Volume up & Power Button for 15 seconds.Release when u feel 3 vibrations.Then try to flash again.

thanks for such swift responses guys.
But i still got the same problem. Flashtool sees it, does nothing and after a while phone restarts.

Nikoloz17 said:
thanks for such swift responses guys.
But i still got the same problem. Flashtool sees it, does nothing and after a while phone restarts.
Click to expand...
Click to collapse
I'm sorry but I'm just trying to help u out with my limited knowledge.
Your Flashtool seems like an old/beta version.Get the latest here
http://www.flashtool.net/download.html
The one that says: Windows Edition : v0.9.11.0 – MD5 : A0F880F3CF420A31D86026F49A2013D7

thanks a lot. That solved it

Nikoloz17 said:
thanks a lot. That solved it
Click to expand...
Click to collapse
Glad I could help.

[Q] Got a hard brick :( plz plz plz helllppppp

I was flashing the alinov's stock kernel and i think it was a bad download,the kernel got flashed succesfully but as u said my device is not powering off nor it is responding any thing on the screen,plz plz plz help me,how to recover mmy device,i came across adfad666 here
http://forum.xda-developers.com/showthread.php?t=2457353
guide but i dont know how to do a full wipe,i even tried to flash stock ftf but it also didnt worked for me,plz help me

Device has to be off to flash an ftf. Have you taken the back cover off and pressed the hard off button?
Sent from my C5303 using XDA Premium 4 mobile app

Parkside said:
Device has to be off to flash an ftf. Have you taken the back cover off and pressed the hard off button?
Sent from my C5303 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Yes i tried that also but the device is not vibrating at all,i tried to connect it to my chrger it doesnt even blink the led indication for charging,the device is also not recognized by the laptop,plz help any body

UPDATE:
i tried to connect it to my laptop frstly i removed my sim n then i tried to reflash it,it doesnt flashed it though,my laptop recognized it as a usb input device and the chrging led is now blinking

shawamawa said:
UPDATE:
i tried to connect it to my laptop frstly i removed my sim n then i tried to reflash it,it doesnt flashed it though,my laptop recognized it as a usb input device and the chrging led is now blinking
Click to expand...
Click to collapse
Try again HARD OFF and then connect your phone to flashmode.then with flashtool flash stock .ftf!

shawamawa said:
I was flashing the alinov's stock kernel and i think it was a bad download,the kernel got flashed succesfully but as u said my device is not powering off nor it is responding any thing on the screen,plz plz plz help me,how to recover mmy device,i came across adfad666 here
http://forum.xda-developers.com/showthread.php?t=2457353
guide but i dont know how to do a full wipe,i even tried to flash stock ftf but it also didnt worked for me,plz help me
Click to expand...
Click to collapse
I just had something similar;
I posted it here: http://forum.xda-developers.com/showthread.php?t=2488870 Might work for you too.

KiaTheKing said:
Try again HARD OFF and then connect your phone to flashmode.then with flashtool flash stock .ftf!
Click to expand...
Click to collapse
I tried it a many times,doent worked
Stirlin said:
I just had something similar;
I posted it here: http://forum.xda-developers.com/showthread.php?t=2488870 Might work for you too.
Click to expand...
Click to collapse
THanks i followed the instructions on ur thread and ended with this,
18/058/2013 09:58:15 - INFO - Selected Xperia SP (C5302) / 12.0.A.2.245 / Indian
18/058/2013 09:58:15 - INFO - Preparing files for flashing
18/059/2013 09:59:10 - INFO - Please connect your device into flashmode.
18/059/2013 09:59:46 - INFO - Device connected with USB debugging off
18/059/2013 09:59:46 - INFO - For 2011 devices line, be sure you are not in MTP mode
18/059/2013 09:59:50 - INFO - Device disconnected
18/000/2013 10:00:55 - INFO - Device connected with USB debugging off
18/000/2013 10:00:55 - INFO - For 2011 devices line, be sure you are not in MTP mode
18/001/2013 10:01:03 - INFO - Device disconnected
18/001/2013 10:01:37 - INFO - Flash canceled
:crying:
............................................................................................................................................
Someone here can plz PM doomlord and adfad666 about this thread,plz

shawamawa said:
I tried it a many times,doent worked
THanks i followed the instructions on ur thread and ended with this,
18/058/2013 09:58:15 - INFO - Selected Xperia SP (C5302) / 12.0.A.2.245 / Indian
18/058/2013 09:58:15 - INFO - Preparing files for flashing
18/059/2013 09:59:10 - INFO - Please connect your device into flashmode.
18/059/2013 09:59:46 - INFO - Device connected with USB debugging off
18/059/2013 09:59:46 - INFO - For 2011 devices line, be sure you are not in MTP mode
18/059/2013 09:59:50 - INFO - Device disconnected
18/000/2013 10:00:55 - INFO - Device connected with USB debugging off
18/000/2013 10:00:55 - INFO - For 2011 devices line, be sure you are not in MTP mode
18/001/2013 10:01:03 - INFO - Device disconnected
18/001/2013 10:01:37 - INFO - Flash canceled
:crying:
............................................................................................................................................
Someone here can plz PM doomlord and adfad666 about this thread,plz
Click to expand...
Click to collapse
When the phone is in Flashmode, and the device isn't receiving any activity, it will restart itself to the system.

shawamawa said:
I tried it a many times,doent worked
THanks i followed the instructions on ur thread and ended with this,
18/058/2013 09:58:15 - INFO - Selected Xperia SP (C5302) / 12.0.A.2.245 / Indian
18/058/2013 09:58:15 - INFO - Preparing files for flashing
18/059/2013 09:59:10 - INFO - Please connect your device into flashmode.
18/059/2013 09:59:46 - INFO - Device connected with USB debugging off
18/059/2013 09:59:46 - INFO - For 2011 devices line, be sure you are not in MTP mode
18/059/2013 09:59:50 - INFO - Device disconnected
18/000/2013 10:00:55 - INFO - Device connected with USB debugging off
18/000/2013 10:00:55 - INFO - For 2011 devices line, be sure you are not in MTP mode
18/001/2013 10:01:03 - INFO - Device disconnected
18/001/2013 10:01:37 - INFO - Flash canceled
:crying:
............................................................................................................................................
Someone here can plz PM doomlord and adfad666 about this thread,plz
Click to expand...
Click to collapse
Al you need to do is to firts go to flashtool (dont connect your device) go to flashmode.choose ftf that you want to install, click flash.and then you will get prepare for flashing line.when its prepared it will said you to connect phone in flashmode..NOW CONNECT PHONE IN FLASHMODE.And thats it!!just connect device in right time!!
Sent from my C5303 using xda app-developers app

Keep volumm down and connect your phone to computer >> open PC companion >> click on Support Zone >> Click on Phone Software update >> Click Repair >> Wait till it done . Try it's . Good luck .

the best method is download SONY UPDATE SERVICE software to your pc. after installing update service, turnoff your mobile then press and hold the volume down key , and connect it with your pc. (even if your phone is not charged no problem ). release the volume down key when the on screen instruction says it. after that if the system says your phone has latest software, then select reinstall the software. wait until it finish. thats all.

dont do too more
just power off ur sp bu stick the reset button in the backcover,and power on,see what happen,take it easy and carefully
shawamawa said:
I was flashing the alinov's stock kernel and i think it was a bad download,the kernel got flashed succesfully but as u said my device is not powering off nor it is responding any thing on the screen,plz plz plz help me,how to recover mmy device,i came across adfad666 here
http://forum.xda-developers.com/showthread.php?t=2457353
guide but i dont know how to do a full wipe,i even tried to flash stock ftf but it also didnt worked for me,plz help me
Click to expand...
Click to collapse

[Q] Xperia Z1 bricked : qhsusb_bulk ?

Hi Guys,
I require your help.
I think i have bricked my Xperia Z1 while trying to flash a ftf.
firstly when i tried to switch on my phone it showed "Update failed please connect to system and update again"
now the phone is totally bricked (no response) and when i try to connect it in flashmode windows detect it as qhsusb_bulk device.
Can anyone please suggest or help !

can you please enumerate your steps of doing this?if it's ok...think positive dont panic!

You are not the first and I think you are not the last. Phone Bricked mean dead, your is not. If you PC can recognize the phone that mean something is working.
So, did you use flashtool v0.9.11 or v0.9.13?

From my previous experience, the best way to rescue Xperia is Sony Update Service.
So, please try SUS.

maxboy said:
From my previous experience, the best way to rescue Xperia is Sony Update Service.
So, please try SUS.
Click to expand...
Click to collapse
Someone said with PC Companion you repair your phone, try as well.

eclyptos said:
Someone said with PC Companion you repair your phone, try as well.
Click to expand...
Click to collapse
Thanks Guys for replies :
Flashtool version 0.9.13.0
Somehow i got the phone being detected in flashmode but now flashtool gives following error :
20/034/2013 17:34:32 - INFO - Selected C6902 / 14.1.G.2.257 / Generic_IN
20/034/2013 17:34:32 - INFO - Preparing files for flashing
20/040/2013 17:40:39 - INFO - Please connect your device into flashmode.
20/041/2013 17:41:02 - INFO - Device connected in flash mode
20/041/2013 17:41:02 - INFO - Opening device for R/W
20/041/2013 17:41:02 - INFO - Reading device information
20/041/2013 17:41:03 - INFO - Phone ready for flashmode operations.
20/041/2013 17:41:03 - INFO - Current device : C6902 - CB51251KDX - 1277-2364_R4A - 1272-6084_14.1.G.1.518 - GLOBAL-HSPA_14.1.G.1.518
20/041/2013 17:41:03 - INFO - Start Flashing
20/041/2013 17:41:03 - INFO - Processing loader.sin
20/041/2013 17:41:03 - INFO - Checking header
20/041/2013 17:41:03 - INFO - Flashing data
20/041/2013 17:41:03 - INFO - Loader : S1_Root_6732 - Version : MSM8974_23 / Boot version : S1_Boot_MSM8974_LA1.0_56-A / Bootloader status : ROOTABLE
20/041/2013 17:41:03 - INFO - Processing partition-image.sin
20/041/2013 17:41:03 - INFO - Checking header
20/041/2013 17:41:03 - INFO - Flashing data
20/041/2013 17:41:03 - INFO - Parsing boot delivery
20/041/2013 17:41:03 - INFO - Phone boot version : S1_Boot_MSM8974_LA1.0_56-A. Boot delivery version : S1_Boot_MSM8974_LA1.0_67
20/041/2013 17:41:03 - INFO - Going to flash boot delivery
20/041/2013 17:41:03 - INFO - Ending flash session
20/041/2013 17:41:03 - ERROR - -1
20/041/2013 17:41:03 - ERROR - Error flashing. Aborted
20/041/2013 17:41:03 - INFO - Device connected in flash mode
20/041/2013 17:41:04 - INFO - Device disconnected
20/041/2013 17:41:06 - INFO - Device connected in flash mode

nice
Karmic. said:
Hi Guys,
I require your help.
I think i have bricked my Xperia Z1 while trying to flash a ftf.
firstly when i tried to switch on my phone it showed "Update failed please connect to system and update again"
now the phone is totally bricked (no response) and when i try to connect it in flashmode windows detect it as qhsusb_bulk device.
Can anyone please suggest or help !
Click to expand...
Click to collapse
i have the same question

eclyptos said:
Someone said with PC Companion you repair your phone, try as well.
Click to expand...
Click to collapse
Since your device is detected by flashtool , please use SUS.
Flashtool has little chance to force flash since it gives errors and stop half way.
But SUS does because it dont need to verifer your phone but you have to choose it from a list, it might not success at the first time but will go through the whole process(i tried to resure xperia TX with 5 flashs and it eventually boot)
So keep flash with SUS until your phone boot.
PC companion need to recognise your phone model so it is a bit tricky.
Sent from my C6906 using xda app-developers app

maxboy said:
Since your device is detected by flashtool , please use SUS.
PC companion need to recognise your phone model so it is a bit tricky.
Click to expand...
Click to collapse
Like you can see in the post the phone is recognised so I don't see the problem.
I will also recommended to try different FTF, it seem like will be some error there.
And at last I will repeated the follow steps:
Keep pressed volume down all the time and connect the phone via usb to PC, do not open flashtool (do not use drivers from sony site, if you installed them uninstall them, windows will do that) wait 1 minute and let windows install the drivers automatically first, then open flashtool, select firmware and flash it, keep pushing volume down all the time. When on the green bar below show up the % of the process you can leave your phone alone. Done.

maxboy said:
Since your device is detected by flashtool , please use SUS.
Flashtool has little chance to force flash since it gives errors and stop half way.
But SUS does because it dont need to verifer your phone but you have to choose it from a list, it might not success at the first time but will go through the whole process(i tried to resure xperia TX with 5 flashs and it eventually boot)
So keep flash with SUS until your phone boot.
PC companion need to recognise your phone model so it is a bit tricky.
Sent from my C6906 using xda app-developers app
Click to expand...
Click to collapse
Or just try flashing using Flashtool and tick "no final verification"

Just2Cause said:
Or just try flashing using Flashtool and tick "no final verification"
Click to expand...
Click to collapse
+1
and wipe data, cache and appslog.

Xperia Z1磚砌：qhsusb_bulk
me too!：（

:crying:
I have the same problem, anyone can help me?
PC recognizes it as qualcomm hs-usb 9008 qdloader my Z1
No Logo Sony, only LED Yellow o RED.
Regards!!! :good:

Kisaraji said:
:crying:
I have the same problem, anyone can help me?
PC recognizes it as qualcomm hs-usb 9008 qdloader my Z1
No Logo Sony, only LED Yellow o RED.
Regards!!! :good:
Click to expand...
Click to collapse
I have the same problem like yours no vibration no led blinking or something i even removed the battery tryed to charge it over 24 hours nothing to get it back to life so we have a hardbricked phone now thanks to 4.3 update and for now the only solution is to change the mainboard or first to chek it with a fully charged battery (new one)

Kisaraji said:
:crying:
I have the same problem, anyone can help me?
PC recognizes it as qualcomm hs-usb 9008 qdloader my Z1
No Logo Sony, only LED Yellow o RED.
Regards!!! :good:
Click to expand...
Click to collapse
Meni30 said:
I have the same problem like yours no vibration no led blinking or something i even removed the battery tryed to charge it over 24 hours nothing to get it back to life so we have a hardbricked phone now thanks to 4.3 update and for now the only solution is to change the mainboard or first to chek it with a fully charged battery (new one)
Click to expand...
Click to collapse
you need to have a look how to flash the device if it is in hs-usb mode (qualcomm is the manufacturer of our snapdragon 800 CPU and the hs-usb mode is meant for vendors to flash bootloader a.s.o.)
i never tried such a thing and maybe it simply can't be done without the special unofficial tools that the vendors have.
so this really looks like a brick ...
hope the best for you guys ...

Kisaraji said:
:crying:
PC recognizes it as qualcomm hs-usb 9008 qdloader my Z1
Click to expand...
Click to collapse
Bored to mention it: Wrong Windwos ADB Drivers. If the device is recognized how can it be bricked. Just wrong set/recognized.
But if you all prefer to send your devices in, open the cases (OMG) or other useless stuff... Entering in Flash/Fastbootmode has nothing to do with the battery. On older Xperia devices you could even flash without/removed battery... The S1 Fastboot unlock worked without battery. How do you think does Sony interact with the ROM's or EEPROMS? A special hidden connector? A special Software? Whispering?

I have the same problem and posted here - http://forum.xda-developers.com/showthread.php?t=2623486

I tried with a second sony xperia z1 that already had 4.3 OTA update and then tried flashing it again using flashtool and it worked so this eliminates the program and usb cable.....the one I have now which is giving me issues is one which had 4.2.2 and im trying to flash to 4.3

z1 fully Dead Hard Brick

z1 completely dead, I instaled hi hackers rom and went well after finishing flashing i did'nt get network of airtel and instaled baseband of 3rd party and it is completely dead nothing is working when i press volume+on button it vibrates 3 times thats it and nothing is displayed and when i put to the charge it shows red light and stops,can anbody help me out from this, please only 3 months old my z1 and sorry for my english ....and can anbody reply friends?
Is it getting red led when I try to charge it ? I don't understand what went wrong.
I had it for about 24 hours on the charger without any signs of "life" in the "mobile".
Hard reset.
Flash a stock FTF using flashtool.
I went through the process of flashing a FTF with flashtool. and its showing....
27/059/2014 02:59:50 - INFO - Selected Bundle for Sony Xperia Z1 (C6903). FW release : 14.1.G.2.257. Customization : GLOBAL-LTE (1277-1398)
27/059/2014 02:59:50 - INFO - Preparing files for flashing
27/000/2014 03:00:36 - INFO - Please connect your device into flashmode.
27/001/2014 03:01:22 - INFO - Device disconnected
27/001/2014 03:01:26 - INFO - Device connected with USB debugging off
27/001/2014 03:01:26 - INFO - For 2011 devices line, be sure you are not in MTP mode
27/001/2014 03:01:35 - INFO - Device disconnected
27/001/2014 03:01:39 - INFO - Device connected with USB debugging off
27/001/2014 03:01:39 - INFO - For 2011 devices line, be sure you are not in MTP mode
can anybody come with this solution........?

as I said in the other thread, turn on usb debugging

if you cant do anything and powering on or connecting your phone to computer or charging it just makes the red led blink, it means its hard bricked. you may need to use test point
but if you dont have baseband and your device runs, try to flash a new modem(i dont know if its available for z1 or not)
and as i see you were trying to flash a much old ftf ... after 4.3 , flashing older than them will make the modem not work.so if you can get in to flash mode try to flash a newer frameware

NiM72NiK said:
if you cant do anything and powering on or connecting your phone to computer or charging it just makes the red led blink, it means its hard bricked. you may need to use test point
but if you dont have baseband and your device runs, try to flash a new modem(i dont know if its available for z1 or not)
and as i see you were trying to flash a much old ftf ... after 4.3 , flashing older than them will make the modem not work.so if you can get in to flash mode try to flash a newer frameware
Click to expand...
Click to collapse
No i can't go into Flash Mode

srichinu said:
No i can't go into Flash Mode
Click to expand...
Click to collapse
unfortunately your phone is hard bricked as its blinking red to everything and must open your phone and hard repair it
follow the instructions on the link below
hope it helps:
http://forum.xda-developers.com/showthread.php?t=2646405
and this is the latest s1 boot .use this one
forum.xda-developers.com/attachment.php?attachmentid=2771435&d=1401467170

ok u give more details for test point and confirm we can try for z1 sir

gregbradley said:
as I said in the other thread, turn on usb debugging
Click to expand...
Click to collapse
no i cant turn usb debugging its full dead ?

srichinu said:
z1 completely dead, I instaled hi hackers rom and went well after finishing flashing i did'nt get network of airtel and instaled baseband of 3rd party and it is completely dead nothing is working when i press volume+on button it vibrates 3 times thats it and nothing is displayed and when i put to the charge it shows red light and stops,can anbody help me out from this, please only 3 months old my z1 and sorry for my english ....and can anbody reply friends?
Is it getting red led when I try to charge it ? I don't understand what went wrong.
I had it for about 24 hours on the charger without any signs of "life" in the "mobile".
Hard reset.
Flash a stock FTF using flashtool.
I went through the process of flashing a FTF with flashtool. and its showing....
27/059/2014 02:59:50 - INFO - Selected Bundle for Sony Xperia Z1 (C6903). FW release : 14.1.G.2.257. Customization : GLOBAL-LTE (1277-1398)
27/059/2014 02:59:50 - INFO - Preparing files for flashing
27/000/2014 03:00:36 - INFO - Please connect your device into flashmode.
27/001/2014 03:01:22 - INFO - Device disconnected
27/001/2014 03:01:26 - INFO - Device connected with USB debugging off
27/001/2014 03:01:26 - INFO - For 2011 devices line, be sure you are not in MTP mode
27/001/2014 03:01:35 - INFO - Device disconnected
27/001/2014 03:01:39 - INFO - Device connected with USB debugging off
27/001/2014 03:01:39 - INFO - For 2011 devices line, be sure you are not in MTP mode
can anybody come with this solution........?
Click to expand...
Click to collapse
Open Flash Tools, select FTF and wait till it says connect your phone. Now hold down volume and plug in USB to PC
If continued, be happy
If not, unplug fully, and then again hold down volume, and then a bit plug in, like image in the link below
Sorry for bad explanation
I experienced brick about five times, and this my own-made method help me
http://d-h.st/FrT

I did has ur instruction red led is lighting continuesly and driver intalling is happening but usb is not recongised and flashing is not done?

srichinu said:
I did has ur instruction red led is lighting continuesly and driver intalling is happening but usb is not recongised and flashing is not done?
Click to expand...
Click to collapse
I think I got what you said
By this method, maybe PC says USB not recognized, but flashing will be done, with no problem
Sent from my C6903 using Tapatalk

MR. Saeed, as he says, its hard bricked . no flash mode or anything..fully dead.. so he cant do anything with flashtool.. seams just opening the phone and fix it in emergency mod is the only solution here ...

NiM72NiK said:
MR. Saeed, as he says, its hard bricked . no flash mode or anything..fully dead.. so he cant do anything with flashtool.. seams just opening the phone and fix it in emergency mod is the only solution here ...
Click to expand...
Click to collapse
Sorry, I did not fully read the first post
I think he just should call emergency to move his phone to hospital
Sent from my C6903 using Tapatalk

SaeedFazlollahzadeh said:
Sorry, I did not fully read the first post
I think he just should call emergency to move his phone to hospital
Sent from my C6903 using Tapatalk
Click to expand...
Click to collapse
He has to open it connect the testpoint to GND and conmect the usb cable and repair it in emergency mode...

srichinu said:
No i can't go into Flash Mode
Click to expand...
Click to collapse
Next time do not be so fast and lazy to read instructions provided by developer of the thing you have flashed. Being fast and thinking wrong and fast sometimes produce fatal thing to the your phone. I am sure you will be no lazy next time and I am sure you will be very careful in operations with your next phone
Whats happening when you press and hold for about 5 secconds power + volumeup button? If you see vibration than you are not in hard brick! If there is no vibration but your phone flashing red all time than its hard brick! If not hard brick you can enter into fastboot mode: disconnect usb cable, press and hold power+volume up until you see vibration, than hold volume up button and in same time connect usb cable. After than you must see blue led! If no blue led than probably try to replace usb drivers by installing sony pc companion, reboot computer after that! Allso make sure comuter device manager detect your phone propertly! After that try again all steps. If this not help and you have red light all time than probably your phone is dead! Hope this help.

USB Debugging

Hi Team,
All of a sudden while i was browsing with my xperia sp, the screen turned blue all of a sudden.
I tried to flash a new ftf BUT i havent turned my usb debugging on .... its off.
Is there any way to turn it on?
P.S. I cant open my mobile in order to turn it on
These are the errors i get after it starts running system.in
31/027/2014 11:27:07 - ERROR - Processing of system.sin finished with errors.
31/027/2014 11:27:07 - INFO - Ending flash session
31/027/2014 11:27:07 - ERROR - ERR_SEVERITY="MAJOR";ERR_CODE="0009";ERR_DYNAMIC="Block verification failed 0x30000510";
Do i have to download another ftf file?

thanman01 said:
Hi Team,
All of a sudden while i was browsing with my xperia sp, the screen turned blue all of a sudden.
I tried to flash a new ftf BUT i havent turned my usb debugging on .... its off.
Is there any way to turn it on?
P.S. I cant open my mobile in order to turn it on
These are the errors i get after it starts running system.in
31/027/2014 11:27:07 - ERROR - Processing of system.sin finished with errors.
31/027/2014 11:27:07 - INFO - Ending flash session
31/027/2014 11:27:07 - ERROR - ERR_SEVERITY="MAJOR";ERR_CODE="0009";ERR_DYNAMIC="Block verification failed 0x30000510";
Do i have to download another ftf file?
Click to expand...
Click to collapse
These errors usually caused by no drivers. Install drivers first just to make sure. Go to Flashtool's Intall Dir\drivers and run the installer. Choose flashmode and fastboot. Scroll down a bit and choose Common drivers for Viskan board. Finish the installation.
You also need to flash when your phone is in its power down state. Did you do that? You can press the yellow button under the back cover using a pen, long enough, and release when 3 vibrations are completed.

hi mate and thanks for your respond.
I flash the latest ftf file and my phone opened normally.
I let it recharge for 2 hours and when i tried to open it again it showed me blue screen lol .
THe funny thing is that when i finished the flashing, the phoned opened normally lmao ... how can that happen now :/
Ill try what you said to me right now, i hope it works

Ok, i tried what you said but i guess my phone has no battery.
I recharge it now but i dont know if its recharging or not :/
I cant see the icon or the red bar that indicates that the phone is recharging.
How do i know if its recharging or no?

thanman01 said:
Ok, i tried what you said but i guess my phone has no battery.
I recharge it now but i dont know if its recharging or not :/
I cant see the icon or the red bar that indicates that the phone is recharging.
How do i know if its recharging or no?
Click to expand...
Click to collapse
Lol were your phone ran out of battery before flashing or while flashing?
Well you can leave it to charge say like 12 hours and try again.

There is a lol problem, my Sony PC Companion says that my phone is model C5302 LOL !!!! And my model is C5303 wtf hahaha

thanman01 said:
There is a lol problem, my Sony PC Companion says that my phone is model C5302 LOL !!!! And my model is C5303 wtf hahaha
Click to expand...
Click to collapse
It was caused by a line in build.prop.

and how do i fix that ? :/

thanman01 said:
and how do i fix that ? :/
Click to expand...
Click to collapse
Sorry I am as well not a professional. Also, I am not using a stock ROM to identify the proper line in build.prop.
But my best bet here is that you flashed a C5302 ROM that may have somehow changed the model of your XSP. I recommend flashing a proper C5303 ftf. If you aware, you can find the stock FTFs here