i installed windows 10 the same drivers screen rotation works but my touchscreen seems to be uncalibrated.
I tried calibration in control panel under tablet settings but it didnt fix the problem.
The touchscreen is split down the middle and mirrored sometimes until the config file is put into system32/inf and the driver installed, if you try to calibrate the touchscreen at all before this is set, I found that it caused it to jump randomly to a corner of the screen and spam open programs.
The solution for me was to plug in a mouse and reset/remove all calibrations and install the driver again from the drivers pack (can't find the thread right this second as I'm at work) along with the touchsetting.cfg, I never had to calibrate the screen as it just worked and is perfectly calibrated automatically?
Related
I just upgraded my Rom for the x time, this time my touch screen will no longer work in landscape. I downgraded to a ROM that used to work, and on that ROM my touchscreen also does not work in landscape mode. Is this a software thing or a result of throwing the phone against the wall to many times? i guess it's time for an 8525....
Any ideas how to get the touchscreen working again?
e.
same problem for me !
It's not switching to lanscape? While opening keys? Or just turning off?
If it's able to be switched with software way (Settings -> Screen -> Landscape), then this is a hardware problem.
Wizars has a magnetic sensor to detect keys sliding, try to check it (use an external magnet).
If screen turning off after sliding the keys, the flat cable is damaged.
My kaiser's touch screen suddenly has aquired an attitude. Some time it works, some it doesn't. When I touch nothing happens. Also when I slide open the keyboard, it works, but as soon as I close the keyboard, it stops working again. When I reboot, the screen works, but it stops after some time. Then it works if I open the keyboard. I have done hard reset, but that hasn't solved the problem.
Is there any thing I can do to fix it.
Now the touch works only if keyboard is open and doesn't work when closed. Any tips (already did hard reset twice).
With more research, the touch screen works but only when pressed very tightly at the point shown in figure (See red circle). Is there any solution to this ?
Will this get fixed if Change LCD ? Or can it be fixed by tightening some screws ?
Hi,
Xperia X1 is three weeks past warranty. Touch screen suddenly stopped working; Display screen still works fine with keyboard in or out. All hardware buttons and keyboard buttons worked, phone worked OK, it was just the touchscreen that was dead. Never had any display problems when sliding keyboard in and out like I have read in here.
HOWEVER...
My mobile Tech Support told me to reset and now all I have is the initial Windows boot screen that says 'Tap the screen to setup...". WTF? Of course when I tap the screen nothing happens.
Is there a key or button combination I can use to invoke the setup routine? Is there anyway to connect it to a PC and control it? Be nice to get the phone back to working, I can live without the touchscreen for now.
There could be an issue of the flex cable being loose. You could try and open your X1 and re-attach the flex cable and hope it solves the issue.
There are some videos out there that shows you how to do it
CyanogenMod installed on Steroids! (RC2/Build 20121210), the hardware keyboard works, then after some time from sleep mode, it stops working until reboot
Complied with all the instructions, rebooted the phone, the problem is not resolved in this way
with broken hardware keyboard, plugged charging usb, and the hardware key to start working again.
restart long and uncomfortable, but if not there then usb cable will only restart.
Since you said that you keyboard start working again with the usb plugged in... I think you problem is not OS related. You have a HW problem. Is a well know bug that the design of the X1 have many flaws (cracky plastic, flex problems, volume rocker issues, keyboard (physical) problems). If you can do it.... try open you handset a do a smal cleaning inside. Sometimes you can have the faulty keys in matter of minutes, but if even this don't work... you should look for a professional technical service that can do it for you.
This kernel implements auto brigthness in the kernel module.
Android setting of screen brightness will be overridden.
lowest level can be set in / sys / module / leds-microp-htckovsky / parameter
This kernel also includes a fix for the lost keys bug. This fix has not been tested.
Click to expand...
Click to collapse
after you install the kernel, do not notice problems with the hardware keyboard
hi,
just recenly when using aamirror with my android auto unit some strange bug seems to have happened and i still couldn't figure out how to fix the problem. let me explain:
it seems whatever i do, the bottom 0,5cm of my screen (above usb-c connection) seems not to response to any touch event within the android system (on my phone - without using android auto connection obviously)
i've tested...:
- bottom touch works fine in twrp
(makes me believe it's not a hardware issue)
- whatever the orientation (if menu is bottom, or status bar) touch will not be recognized
(in android)
- menu buttons are working fine when 180° reverse
- menu buttons work though touch simulation (scrcpy)
- i noticed it right about when having some issues with aamirror somewhat lagging my phone
so generally speaking i could only think of something intercepting the touch events.
i also tried removing both apps, rebooting, dirty flashed another update
with and without plugging it into android auto again and again.
what could be the problem??