yesterday i got micromax a250 canvas for update 4.4 . according to below method i flashed the phone successfully. everything ok no errors. after update phone wont power on. sometimes only charging no power. once it was on when logo appear become freezed. i am in big trouble now ? please explain me to solve this problem.
a) You need to download Rom and SP Tool from above link.
b) Download AND Install MTK Drivers.
c) Reboot your PC.
d) Unrar S9311_MP_IN_MMX_15_flasher_user.rar and unzip SP_Flash_Tool_exe_v3.1312.0.139.zip using any Unrar tool like peazip, 7zip, winrar.
e) You will have two folder S9311_MP_IN_MMX_15_flasher_user and SP_Flash_Tool_exe_v3.1312.0.139.
f) Switch off Your Phone. Make sure you have sufficient battery charged or use laptop to do this. (Do NOT connect phone to PC)
g) Open Flash_tool.exe from folder SP_Flash_Tool_exe_v3.1312.0.139.
h) Click Scatter-Loading button, choose MT6589_Android_scatter.txt file from folder S9311_MP_IN_MMX_15_flasher_user.
i) Wait file to be added into Flash Tool.
j) Choose Option->USB Model, click USB Model.
k) Choose Option->DA DownLoad All->Speed->High Speed, click High Speed.
l) Click Firmware download.
m) Now connect phone.
n) Software start downloading.
o) After few minutes you will see big green circle.
p) Done. Boot your phone.
wasimbai said:
yesterday i got micromax a250 canvas for update 4.4 . according to below method i flashed the phone successfully. everything ok no errors. after update phone wont power on. sometimes only charging no power. once it was on when logo appear become freezed. i am in big trouble now ? please explain me to solve this problem.
a) You need to download Rom and SP Tool from above link.
b) Download AND Install MTK Drivers.
c) Reboot your PC.
d) Unrar S9311_MP_IN_MMX_15_flasher_user.rar and unzip SP_Flash_Tool_exe_v3.1312.0.139.zip using any Unrar tool like peazip, 7zip, winrar.
e) You will have two folder S9311_MP_IN_MMX_15_flasher_user and SP_Flash_Tool_exe_v3.1312.0.139.
f) Switch off Your Phone. Make sure you have sufficient battery charged or use laptop to do this. (Do NOT connect phone to PC)
g) Open Flash_tool.exe from folder SP_Flash_Tool_exe_v3.1312.0.139.
h) Click Scatter-Loading button, choose MT6589_Android_scatter.txt file from folder S9311_MP_IN_MMX_15_flasher_user.
i) Wait file to be added into Flash Tool.
j) Choose Option->USB Model, click USB Model.
k) Choose Option->DA DownLoad All->Speed->High Speed, click High Speed.
l) Click Firmware download.
m) Now connect phone.
n) Software start downloading.
o) After few minutes you will see big green circle.
p) Done. Boot your phone.
Click to expand...
Click to collapse
Update 4.4 ?? You mean Android 4.4 KitKat for your Canvas Turbo ?? Do you mean that ?? Please let me know in detail from where you downloaded those Flash tool and all other files for your Canvas Turbo.
how to increase more performance in it.....because i am getting hang in im phone..
Android 4.4 update is not available yet for any Micromax phone...
hi,
my micromax a1 was runnning marshmallow 6.0.1 when during a security patch update installation got stuck and failed to boot again. now just booting into "dead android with exclamation mark". upon pressing power button and volume up and going into recovery(Android stock recovery) menu , cant wipe partition or data as it throws error "E: failed to mount/ cache" errors..
upon trying to install with any SD card also throws same error.
then i tried to install through ADB, while connecting to PC , PC not detecting mobile in recovery mode but detecting in bootloader mode. with fastboot flash command (for installing TWRP/CWM) in bootloader mode, error coming as "sending recovery failed(unknown status code)" .
Kindly help...
same happened to me yesterday . do you find any solution ??
Hi there !
STEP 1: DOWNLOAD the FLASH TOOL from this this link :LINK TO DOWNLOAD FILE
It is almost 30 MB in Size. And EXTRACT / UNZIP it to Desktop ( OR SOMEWHERE ) of your computer.
STEP 2: DOWNLOAD LOLLIPOP FLASH FILE
DOWNLOAD LINK FOR LOLLIPOP: HERE
After downloading this flash file EXTRACT / UNZIP it to Desktop ( OR SOMEWHERE ) on your computer.
STEP 3: NOW INSTALL DRIVERS:
YOU NEED TO BE ON WINDOWS 7 TO INSTALL DRIVERS (WINDOWS 8 DOESN'T SUPPORT THIS DRIVER / PHONE IS NOT DETECTED)
DOWNLOAD DRIVERS from this link : HERE
EXTRACT AND INSTALL THE DRIVERS : Next next next and finish If you see an security warning ( a red coloured pop up ) choose INSTALL IT ANYWAY
IT IS RECOMMENDED YOU TO RESTART YOUR PC.
STEP 4:
Now we have Extrated /unziped 2 files. One is FLASHTOOLS and other is FLASH FILE and Extracted it or unziped it to Desktop or Somewhere.
One of it having the name SP_Flash_Tool_exe_windows_v5.1424.00 or open both folders then one of it having the flashing tool. OPEN THE FOLDER NAMED SP_Flash_Tool_exe_windows_v5.1424.00
it contains an application named fashtool.exe OPEN IT
NOW THE APPLICATION IS ASKING FOR SCATTER LOADING FILE
its a txt file which is on the extracted flash file folder
BROWSE it by clicking Button named Scatter Loading
click OPEN
STEP 5:
HERE IN THE DROPDOWN BOX, IT SAYS DOWNLOAD ONLY, CLICK ON IT AND SELECT FIRMWARE UPDATE ONLY.
IF YOU SELECT FORMAT + DOWNLOAD, THEN YOU WILL LOOSE IMEI NUMBER.
NOW CLICK DOWNLOAD BUTTON ( GREEN ARROWED BUTTON NAMED DOWNLOAD )
IN CASE YOU LOOSE IMEI NUMBER, THEN REFER HERE
STEP 6:
Now SWITCH OFF your PHONE and REMOVE BATTERY
STEP 7:
CONNECT your PC via USB CABLE
wait for the driver Detection.
THE FLASHING PROCESS WILL START AUTOMATICALLY you can See the progress in progress bar which is on bottom of flashing tool Application.
WHEN IT IS FINISHED DISCONNECT USB AND RESTART YOUR PHONE.
NOW YOU WILL GET LOLLIPOP UPDATE IMMEDIATELY.
NOW REFER HERE TO ROOT MARSHMALLOW
HIT THANKS IF HELPED
if link do not work here properly then just google 'canvas a1 stuck on startup' ... and follow link in associated with xda
Device is dead
My phone is neither switching on, nor charging.
I flashed the stock ROM due to some problem with the rooted device through SP Flash tools. It completed successfully, but the device is not switching on or charging.
KIndly help
Hi, this is stoch China ROM for IdeaTab A3000-H. It has only Chinesse and English languages. And it has A3000_prc_3gfull partition table, requied to flash many ROMs It deletes data (because of flash).
Ok, here is a link to firmware: https://www.mediafire.com/file/6g138sppofvioe5/A3000_A421_000_029_130327_CN_3G.zip/file
Link for drivers for MT65xx Preloader: https://www.mediafire.com/file/r8y5olumc16iye2/Drivers_v1.2_A3.zip/file
Link for SP Flash Tool: https://www.mediafire.com/file/dtl5mlckqxofpul/SP_Flash_Tool_v3.1336.0.198.zip/file
Spoiler: Instructions to flash this ROM
1. First of all, download ROM, drivers and SP Flash Tool.
2. Unpack drivers, ROM and Flash Tool
3. Run SP Flash Tool, press Scatter-loading, select MT6589_Android_scatter_emmc.txt from unpacked folder with ROM
4. Press Download.
5. Turn off tablet, connect it to PC with USB
6. Press Ctrl + R and type devmgmt.msc, click enter.
7. Find "MT65XX Preloader", click on update driver
8. Select "Manual update"
9. Browse the files, select "amd64" folder from "Drivers 1.2".
10. OK, if finished, unplug USB from PC.
11. Connect tablet again
12. If there is any error in SP Flash Tool, click "Stop" and "Firmware Upgrade"
13. Wait for green ring and voila!
If you like it, press Thanks
I hope you like it
How can I just replage logo.bin
mickchip said:
How can I just replage logo.bin
Click to expand...
Click to collapse
Uncheck all images (USRDATA, ANDROID, CACHE), check only LOGO and click Download. Then connect your tablet (power off it before) and done
Done, thank you.
mickchip said:
Done, thank you.
Click to expand...
Click to collapse
Press Like button, if you can
X7 MAX and GT NEO FLASH/UBRICK
CONVERT GT NEO/GT NEO FE to X7 MAX
(and vice versa)
BACKUP
Please read all the information before proceeding.
1) In Developer options need turn "ON", "OEM unlock" and USB Debug.
2) Unlock your bootloader.
Spoiler: UNLOCK INSTRUCTION
-Save the DeepTesting. apk application on the phone and run it. (there are two versions in the archive for GT NEO and GT NEO FE)
- Run.
Then follow the screenshots.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
We are waiting. After about 15-60 minutes (or more), the unlock tool will show the status of the unlock request. If it shows that the unlock was successful (as in the screenshot below), we proceed to the next step.
You can exit the app and log in later to check the status.
The device itself should reboot into fastboot mode.
You should have ADB drivers installed, if there are none, then you will see an Android device in the device manager.
The ADB drivers are in the "Programs and Drivers" folder at the links above, unpack and install them manually.
Click on "Android", then "driver", then "update driver". Next, " Find drivers on this PC (search and install the driver manually)".
Next, "Select a driver from the list of available ones", then "Show all devices" (this item may remain), then "install from disk", search for our adb drivers folder, click on " android_winusb. inf "
and select"Android Bootloader Interface" from the list. Done.
Next, run BL UNLOCK.bat from the folder "Unlock Bootloader", Read the instructions in the bat file, press any key. We look at the phone. Confirm Unlcok.
After that, we run FASTBOOT REBOOT.bat
This restart will delete all user data.
Then turn off the phone. Disconnect the USB cable.
Click " Start deep testing”
3) Disable Driver Signature Enforcement in Windows 10: Video tutorial
4) Download all utilites and unpack: Programms and Drivers
5) Download A27 (GT_NEO) firmwire and unpack: A27 Firmwire for FTools (MEGA); A27 Firmwire for FTools (GDrive)
Download A15 (X7_MAX) firmwire and unpack: A15 Firmwire for FTools (MEGA); A15 Firmwire for FTools (GDrive)
6) Install VCOM drivers and libusb
7) Open flash_tool.exe and choose MT6893_Android_scatter.txt from unpacked firmwire
8) In Download Agent choose MTK_AllInOne_DA.bin
9) GO options-->Connections--> choose UART and Band rate: 921600
10) Choose DOWNLOAD ONLY mode and check all the boxes. DONT CHOOSE DIFFERENT MODE!!!!
11) Power OFF Phone and unplag usb cable
12) Open" MTKAuthBypassTool_V6" (mtksecbypass.exe) with administrator rights. Click on "Disable Auth"
13) Hold VOL+ and VOL- and Connect Usb cable. Now you must see in device manager Com port MediaTek USB Port_V1632. If you see MediaTek port, unhold VOL buttons. Remember the port number!
After connect usb cable in MTKAuthBypassTool_V6 you can see this:
14) Fastest Check options-->Connections--> UART and Band rate: 921600,
choose MediaTek USB Port Com port
15) After this message click "DOWNLOAD" in FlashTools
(if you are slow and an error appears, you must repeat the procedure from step "11". Do not close the FlashTools program so that the port settings and port speed do not get lost.)
16) Unplag USB cable. Dont turn ON phone! Go Fastboot mode ( Hold VOL- and Power button)
17) Launching RECOVERY.bat in the "Unlock Bootloader"folder.
18) Format Data in Recovery
The first download is long, we are waiting from 5 to 10 minutes.
19) LOCK BOOTLOADER AGAIN
This stage is necessary in order for the device to become certified and certain services (Gpay, etc.) to work
- Turn off the phone.
- Hold the VOL-and the power button. We enter the Fastboot mode.
- Launch BL LOCK.bat from the “Unlock Bootloader " folder. Follow the instructions in the bat
- After launching FASTBOOT REBOOT.bat
The phone will reboot itself.
Done. Congratulations. You have stock clean firmwire with OTA and full work services!
IF YOU WANT FLASH WITH LOCK BOOTLOADER
Skip the STEPS for unlocking and blocking the bootloder.
Uncheck boxes in SP FlashTools from:
opporeserve2
cdt_engineering
md1mg
IF YOU HAVE PROBLEM WITH THE COM PORT OR ERROR IN MTKAuthBypassTool_V6
- You must do this before stage 12
- After install libusb you will see a folder "lib-usb" in the START menu
- Launch the "Filter Wizard" (select "Install a device filter" and see a window with devices.
-When the phone is turned off, press the VOL+ and VOL-keys and connect the USB cord. Once the port has been determined, release the volume keys after a couple of seconds.
-In the Filter Wizard window, we quickly catch MediaTek USB Port_V1632 and click Install. We act quickly. There should be a response from the program that everything is success and the phone will reboot.
- Turn off the phone. Disconnect the cord.
- Your port problems must be lost
- Go Step 12
ABOUT BACKUP!
- If you wnat make Backup your Phone, follow steps 7-14
- After message from "MTKAuthBypassTool_V6" Go to the “ReadBack " tab in FlashTools and check the boxes everywhere and quickly click on " Read Back”
- Your BackUP data it will be saved in the SP FLASH TOOLS folder as ROM_1, ROM_2 etc
- DONE.
HOW FLASH BACKUP?
- Unlock Bootloader
- Download this: -=Backup Flash=-
- Unpack and copy your backup ROM_ files in this folder
- Choose scatter from this folder in SP Flash Tools
- Uncheck SECCFG (ROM_20) and flash ( Dont forget use MTKbypass utility and check port)
- After Flashig again go EDL mode and flash only SECCFG (ROM_20)
- Maybe need Format Data in Recovery
- Done
Hi please can you provide files for Realme GT Neo Flash Edition (FE) as it has the latest firmware A.11. You provided files for only GT Neo and X7 Max. Find attached a screenshot showing the current GT Neo Flash Edition Firmware. Thank you
mahotlov said:
X7 MAX and GT NEO FLASH/UBRICK
CONVERT GT NEO/GT NEO FE to X7 MAX
(and vice versa)
BACKUP
1) In Developer options need turn "ON", "OEM unlock" and USB Debug.
2) Unlock your bootloader.
Spoiler: UNLOCK INSTRUCTION
-Save the DeepTesting. apk application on the phone and run it. (there are two versions in the archive for GT NEO and GT NEO FE)
- Run.
Then follow the screenshots.
View attachment 5415895View attachment 5415897View attachment 5415899
We are waiting. After about 15-60 minutes (or more), the unlock tool will show the status of the unlock request. If it shows that the unlock was successful (as in the screenshot below), we proceed to the next step.
You can exit the app and log in later to check the status.
View attachment 5415901
The device itself should reboot into fastboot mode.
You should have ADB drivers installed, if there are none, then you will see an Android device in the device manager.
The ADB drivers are in the "Programs and Drivers" folder at the links above, unpack and install them manually.
Click on "Android", then "driver", then "update driver". Next, " Find drivers on this PC (search and install the driver manually)".
Next, "Select a driver from the list of available ones", then "Show all devices" (this item may remain), then "install from disk", search for our adb drivers folder, click on " android_winusb. inf "
and select"Android Bootloader Interface" from the list. Done.
Next, run BL UNLOCK.bat from the folder "Unlock Bootloader", Read the instructions in the bat file, press any key. We look at the phone. Confirm Unlcok.
After that, we run FASTBOOT REBOOT.bat
This restart will delete all user data.
Then turn off the phone. Disconnect the USB cable.
Click " Start deep testing”
3) Disable Driver Signature Enforcement in Windows 10: Video tutorial
4) Download all utilites and unpack: Programms and Drivers
5) Download A27 (GT_NEO) firmwire and unpack: A27 Firmwire for FTools (MEGA); A27 Firmwire for FTools (GDrive)
Download A15 (X7_MAX) firmwire and unpack: A15 Firmwire for FTools (MEGA); A15 Firmwire for FTools (GDrive)
6) Install VCOM drivers and libusb
7) Open flash_tool.exe and choose MT6893_Android_scatter.txt from unpacked firmwire
8) In Download Agent choose MTK_AllInOne_DA.bin
9) GO options-->Connections--> choose UART and Band rate: 921600
10) Choose Download Only mode and check all the boxes.
11) Power OFF Phone and unplag usb cable
12) Open" MTKAuthBypassTool_V6" (mtksecbypass.exe) with administrator rights. Click on "Disable Auth"
13) Hold VOL+ and VOL- and Connect Usb cable. Now you must see in device manager Com port MediaTek USB Port_V1632. If you see MediaTek port, unhold VOL buttons. Remember the port number!
After connect usb cable in MTKAuthBypassTool_V6 you can see this:
View attachment 5415903
14) Fastest Check options-->Connections--> UART and Band rate: 921600,
choose MediaTek USB Port Com port
15) After this message click "DOWNLOAD" in FlashTools
(if you are slow and an error appears, you must repeat the procedure from step "11". Do not close the FlashTools program so that the port settings and port speed do not get lost.)
16) Unplag USB cable and turn ON phone.
The first download is long, we are waiting from 5 to 10 minutes. Has it started?
I recommend doing a full data reset.
If the device does not start after a long wait and reboots itself or freezes (rarely, but it is possible), go to Recovery and make Format Data.
How do load in Recovery? Press VOL - and the ON buttons, the phone will switch to fastboot mode.
Launching RECOVERY.bat in the "Unlock Bootloader"folder.
17) LOCK BOOTLOADER AGAIN
This stage is necessary in order for the device to become certified and certain services (Gpay, etc.) to work
- Turn off the phone.
- Hold the VOL-and the power button. We enter the Fastboot mode.
- Launch BL LOCK.bat from the “Unlock Bootloader " folder. Follow the instructions in the bat
- After launching FASTBOOT REBOOT.bat
The phone will reboot itself.
Done. Congratulations. You have stock clean firmwire with OTA and full work services!
IF YOU HAVE PROBLEM WITH THE COM PORT OR ERROR IN MTKAuthBypassTool_V6
- You must do this before stage 12
- After install libusb you will see a folder "lib-usb" in the START menu
- Launch the "Filter Wizard" (select "Install a device filter" and see a window with devices.
-When the phone is turned off, press the VOL+ and VOL-keys and connect the USB cord. Once the port has been determined, release the volume keys after a couple of seconds.
-In the Filter Wizard window, we quickly catch MediaTek USB Port_V1632 and click Install. We act quickly. There should be a response from the program that everything is success and the phone will reboot.
- Turn off the phone. Disconnect the cord.
- Your port problems must be lost
- Go Step 12
ABOUT BACKUP!
- If you wnat make Backup your Phone, follow steps 7-14
- After message from "MTKAuthBypassTool_V6" Go to the “ReadBack " tab in FlashTools and check the boxes everywhere and quickly click on " Read Back”
- Your BackUP data it will be saved in the SP FLASH TOOLS folder as ROM_1, ROM_2 etc
- DONE.
Click to expand...
Click to collapse
Question #1. I'm having currently an unlocked bootloader, and custom GSI installed (GT Neo). Do i need another instructions to do?
philipjan26 said:
Question #1. I'm having currently an unlocked bootloader, and custom GSI installed (GT Neo). Do i need another instructions to do?
Click to expand...
Click to collapse
No. dont lock, firstly flash Firmwire
Update:
Im able to change my GT Neo ROM to Indian Variant. Thank you so much sir!
Experience:
Instruction #13-#15 are quite tricky.
Issues Encountered:
- my windows pc cannot detect the mediatek com port
- proper timing of clicking DOWNLOAD on SP Flash Tool
How i manage to proceed on SP FT Download:
- first turn off phone (assuming below instructions are DONE -> How i fixed (to detect):)
- SP Flash Tool needed Configs are Done (just waiting for the Downlolad to be clicked)
- MTK Bypass (Administration) is waiting for device
- after SUCCESS MESSAGE on MTK Bypass, immediately click on Download (SP FT)
- once download is started, you can unhold VOL - & + wait to be finished
How i fixed (to detect):
- downloaded this mediatek vcom drivers -> https://www.thecustomdroid.com/mediatek-preloader-usb-vcom-drivers/
- there are some popup that appear (i forgot to remember), i just clicked yes
- then restart pc
- turn off device
- open LIBUSB Filter device (Goal is to detect "Mediatek xxxxx yyyyy zzzzz" usb device on the list)
- Hold VOL - & VOL + AND PLUG Type C Cable
- Check the LIBUSB Filter list and once you see any "MEDIATEK ZZZZZ XXX" click and install
- once success, you can go to -> How i manage to proceed on SP FT Download:
Hope that helps! Thank you .
[email protected] said:
Hi please can you provide files for Realme GT Neo Flash Edition (FE) as it has the latest firmware A.11. You provided files for only GT Neo and X7 Max. Find attached a screenshot showing the current GT Neo Flash Edition Firmware. Thank you
Click to expand...
Click to collapse
You can use firmware for Gt Neo or X7 Max (better) for FE ver. phone
mahotlov said:
X7 MAX and GT NEO FLASH/UBRICK
CONVERT GT NEO/GT NEO FE to X7 MAX
(and vice versa)
BACKUP
1) In Developer options need turn "ON", "OEM unlock" and USB Debug.
2) Unlock your bootloader.
Spoiler: UNLOCK INSTRUCTION
-Save the DeepTesting. apk application on the phone and run it. (there are two versions in the archive for GT NEO and GT NEO FE)
- Run.
Then follow the screenshots.
View attachment 5415895View attachment 5415897View attachment 5415899
We are waiting. After about 15-60 minutes (or more), the unlock tool will show the status of the unlock request. If it shows that the unlock was successful (as in the screenshot below), we proceed to the next step.
You can exit the app and log in later to check the status.
View attachment 5415901
The device itself should reboot into fastboot mode.
You should have ADB drivers installed, if there are none, then you will see an Android device in the device manager.
The ADB drivers are in the "Programs and Drivers" folder at the links above, unpack and install them manually.
Click on "Android", then "driver", then "update driver". Next, " Find drivers on this PC (search and install the driver manually)".
Next, "Select a driver from the list of available ones", then "Show all devices" (this item may remain), then "install from disk", search for our adb drivers folder, click on " android_winusb. inf "
and select"Android Bootloader Interface" from the list. Done.
Next, run BL UNLOCK.bat from the folder "Unlock Bootloader", Read the instructions in the bat file, press any key. We look at the phone. Confirm Unlcok.
After that, we run FASTBOOT REBOOT.bat
This restart will delete all user data.
Then turn off the phone. Disconnect the USB cable.
Click " Start deep testing”
3) Disable Driver Signature Enforcement in Windows 10: Video tutorial
4) Download all utilites and unpack: Programms and Drivers
5) Download A27 (GT_NEO) firmwire and unpack: A27 Firmwire for FTools (MEGA); A27 Firmwire for FTools (GDrive)
Download A15 (X7_MAX) firmwire and unpack: A15 Firmwire for FTools (MEGA); A15 Firmwire for FTools (GDrive)
6) Install VCOM drivers and libusb
7) Open flash_tool.exe and choose MT6893_Android_scatter.txt from unpacked firmwire
8) In Download Agent choose MTK_AllInOne_DA.bin
9) GO options-->Connections--> choose UART and Band rate: 921600
10) Choose Download Only mode and check all the boxes.
11) Power OFF Phone and unplag usb cable
12) Open" MTKAuthBypassTool_V6" (mtksecbypass.exe) with administrator rights. Click on "Disable Auth"
13) Hold VOL+ and VOL- and Connect Usb cable. Now you must see in device manager Com port MediaTek USB Port_V1632. If you see MediaTek port, unhold VOL buttons. Remember the port number!
After connect usb cable in MTKAuthBypassTool_V6 you can see this:
View attachment 5415903
14) Fastest Check options-->Connections--> UART and Band rate: 921600,
choose MediaTek USB Port Com port
15) After this message click "DOWNLOAD" in FlashTools
(if you are slow and an error appears, you must repeat the procedure from step "11". Do not close the FlashTools program so that the port settings and port speed do not get lost.)
16) Unplag USB cable and turn ON phone.
The first download is long, we are waiting from 5 to 10 minutes. Has it started?
I recommend doing a full data reset.
If the device does not start after a long wait and reboots itself or freezes (rarely, but it is possible), go to Recovery and make Format Data.
How do load in Recovery? Press VOL - and the ON buttons, the phone will switch to fastboot mode.
Launching RECOVERY.bat in the "Unlock Bootloader"folder.
17) LOCK BOOTLOADER AGAIN
This stage is necessary in order for the device to become certified and certain services (Gpay, etc.) to work
- Turn off the phone.
- Hold the VOL-and the power button. We enter the Fastboot mode.
- Launch BL LOCK.bat from the “Unlock Bootloader " folder. Follow the instructions in the bat
- After launching FASTBOOT REBOOT.bat
The phone will reboot itself.
Done. Congratulations. You have stock clean firmwire with OTA and full work services!
IF YOU HAVE PROBLEM WITH THE COM PORT OR ERROR IN MTKAuthBypassTool_V6
- You must do this before stage 12
- After install libusb you will see a folder "lib-usb" in the START menu
- Launch the "Filter Wizard" (select "Install a device filter" and see a window with devices.
-When the phone is turned off, press the VOL+ and VOL-keys and connect the USB cord. Once the port has been determined, release the volume keys after a couple of seconds.
-In the Filter Wizard window, we quickly catch MediaTek USB Port_V1632 and click Install. We act quickly. There should be a response from the program that everything is success and the phone will reboot.
- Turn off the phone. Disconnect the cord.
- Your port problems must be lost
- Go Step 12
ABOUT BACKUP!
- If you wnat make Backup your Phone, follow steps 7-14
- After message from "MTKAuthBypassTool_V6" Go to the “ReadBack " tab in FlashTools and check the boxes everywhere and quickly click on " Read Back”
- Your BackUP data it will be saved in the SP FLASH TOOLS folder as ROM_1, ROM_2 etc
- DONE.
Click to expand...
Click to collapse
Following your instruction properly.. but still getting this error while flashing.
@mahotlov please take a look into this.
MahiSingh083 said:
View attachment 5416559
Following your instruction properly.. but still getting this error while flashing.
@mahotlov please take a look into this.
Click to expand...
Click to collapse
You flash with lock bootloader.
Uncheck boxes from:
opporeserve2
cdt_engineering
md1mg
Guys, i have a doubt i am gonna buy this phone like in a week so when u buy the phone does it come with latest update (a.18) or it comes with a.15 y am asking is becoz in a.16,17,18 to many bugs so only anyone reply me
TeckySairam said:
Guys, i have a doubt i am gonna buy this phone like in a week so when u buy the phone does it come with latest update (a.18) or it comes with a.15 y am asking is becoz in a.16,17,18 to many bugs so only anyone reply me
Click to expand...
Click to collapse
It does not matter since it is easy to downgrade to a15 as per the OP instructions. I tried this multiple times.
vikas776 said:
It does not matter since it is easy to downgrade to a15 as per the OP instructions. I tried this multiple times.
Click to expand...
Click to collapse
KK Thnx For Quick Reply!!
It works great, @mahotlov thank you for sharing this, for your help, and guys this is legit, follow carefully the steps.
Thanks for this worked perfectly.
One thing to note you have to work fast when put into MTK mode as it will disconnect rather quickly.
Thank you. Totally worth the time. The x7 Max firmware feels much better than the GT Neo one.
mahotlov said:
X7 MAX and GT NEO FLASH/UBRICK
CONVERT GT NEO/GT NEO FE to X7 MAX
(and vice versa)
BACKUP
Please read all the information before proceeding.
1) In Developer options need turn "ON", "OEM unlock" and USB Debug.
2) Unlock your bootloader.
Spoiler: UNLOCK INSTRUCTION
-Save the DeepTesting. apk application on the phone and run it. (there are two versions in the archive for GT NEO and GT NEO FE)
- Run.
Then follow the screenshots.
View attachment 5415895View attachment 5415897View attachment 5415899
We are waiting. After about 15-60 minutes (or more), the unlock tool will show the status of the unlock request. If it shows that the unlock was successful (as in the screenshot below), we proceed to the next step.
You can exit the app and log in later to check the status.
View attachment 5415901
The device itself should reboot into fastboot mode.
You should have ADB drivers installed, if there are none, then you will see an Android device in the device manager.
The ADB drivers are in the "Programs and Drivers" folder at the links above, unpack and install them manually.
Click on "Android", then "driver", then "update driver". Next, " Find drivers on this PC (search and install the driver manually)".
Next, "Select a driver from the list of available ones", then "Show all devices" (this item may remain), then "install from disk", search for our adb drivers folder, click on " android_winusb. inf "
and select"Android Bootloader Interface" from the list. Done.
Next, run BL UNLOCK.bat from the folder "Unlock Bootloader", Read the instructions in the bat file, press any key. We look at the phone. Confirm Unlcok.
After that, we run FASTBOOT REBOOT.bat
This restart will delete all user data.
Then turn off the phone. Disconnect the USB cable.
Click " Start deep testing”
3) Disable Driver Signature Enforcement in Windows 10: Video tutorial
4) Download all utilites and unpack: Programms and Drivers
5) Download A27 (GT_NEO) firmwire and unpack: A27 Firmwire for FTools (MEGA); A27 Firmwire for FTools (GDrive)
Download A15 (X7_MAX) firmwire and unpack: A15 Firmwire for FTools (MEGA); A15 Firmwire for FTools (GDrive)
6) Install VCOM drivers and libusb
7) Open flash_tool.exe and choose MT6893_Android_scatter.txt from unpacked firmwire
8) In Download Agent choose MTK_AllInOne_DA.bin
9) GO options-->Connections--> choose UART and Band rate: 921600
10) Choose Download Only mode and check all the boxes.
11) Power OFF Phone and unplag usb cable
12) Open" MTKAuthBypassTool_V6" (mtksecbypass.exe) with administrator rights. Click on "Disable Auth"
13) Hold VOL+ and VOL- and Connect Usb cable. Now you must see in device manager Com port MediaTek USB Port_V1632. If you see MediaTek port, unhold VOL buttons. Remember the port number!
After connect usb cable in MTKAuthBypassTool_V6 you can see this:
View attachment 5415903
14) Fastest Check options-->Connections--> UART and Band rate: 921600,
choose MediaTek USB Port Com port
15) After this message click "DOWNLOAD" in FlashTools
(if you are slow and an error appears, you must repeat the procedure from step "11". Do not close the FlashTools program so that the port settings and port speed do not get lost.)
16) Unplag USB cable. Dont turn ON phone! Go Fastboot mode ( Hold VOL- and Power button)
17) Launching RECOVERY.bat in the "Unlock Bootloader"folder.
18) Format Data in Recovery
The first download is long, we are waiting from 5 to 10 minutes.
19) LOCK BOOTLOADER AGAIN
This stage is necessary in order for the device to become certified and certain services (Gpay, etc.) to work
- Turn off the phone.
- Hold the VOL-and the power button. We enter the Fastboot mode.
- Launch BL LOCK.bat from the “Unlock Bootloader " folder. Follow the instructions in the bat
- After launching FASTBOOT REBOOT.bat
The phone will reboot itself.
Done. Congratulations. You have stock clean firmwire with OTA and full work services!
IF YOU WANT FLASH WITH LOCK BOOTLOADER
Skip the STEPS for unlocking and blocking the bootloder.
Uncheck boxes in SP FlashTools from:
opporeserve2
cdt_engineering
md1mg
IF YOU HAVE PROBLEM WITH THE COM PORT OR ERROR IN MTKAuthBypassTool_V6
- You must do this before stage 12
- After install libusb you will see a folder "lib-usb" in the START menu
- Launch the "Filter Wizard" (select "Install a device filter" and see a window with devices.
-When the phone is turned off, press the VOL+ and VOL-keys and connect the USB cord. Once the port has been determined, release the volume keys after a couple of seconds.
-In the Filter Wizard window, we quickly catch MediaTek USB Port_V1632 and click Install. We act quickly. There should be a response from the program that everything is success and the phone will reboot.
- Turn off the phone. Disconnect the cord.
- Your port problems must be lost
- Go Step 12
ABOUT BACKUP!
- If you wnat make Backup your Phone, follow steps 7-14
- After message from "MTKAuthBypassTool_V6" Go to the “ReadBack " tab in FlashTools and check the boxes everywhere and quickly click on " Read Back”
- Your BackUP data it will be saved in the SP FLASH TOOLS folder as ROM_1, ROM_2 etc
- DONE.
Click to expand...
Click to collapse
as i have x7 max(INDIA) , can i install realme gt neo deep testing apk and unlock its bootloader and after flashing the firmware can i get backk to the locked bootloader state ?? through your.bat file or i"ll get stuck on image destroyed page ??
great!
Could you guide how to go back to gt neo firmware from X7 Max firmware??
And anyway to remove the google dialer? too annoying
abidrockzx said:
as i have x7 max(INDIA) , can i install realme gt neo deep testing apk and unlock its bootloader and after flashing the firmware can i get backk to the locked bootloader state ?? through your.bat file or i"ll get stuck on image destroyed page ??
Click to expand...
Click to collapse
You can use Deep apk for X7 Max or GT Neo. No problem
Shou1814 said:
great!
Could you guide how to go back to gt neo firmware from X7 Max firmware??
And anyway to remove the google dialer? too annoying
Click to expand...
Click to collapse
1. Yes. Everything is the same, just use the firmware for Gt neo( A27)
2. Remove without root- No.
You can use another dialer
mahotlov said:
You can use Deep apk for X7 Max or GT Neo. No problem
1. Yes. Everything is the same, just use the firmware for Gt neo( A27)
2. Remove without root- No.
You can use another dialer
Click to expand...
Click to collapse
i do the same to come back into gt neo but it appear that
Please help me
Thanks
Shou1814 said:
View attachment 5437159
i do the same to come back into gt neo but it appear that
Please help me
Thanks
Click to expand...
Click to collapse
I need full screenshot FlashTools and Mtkauthbyoass tool
mahotlov said:
I need full screenshot FlashTools and Mtkauthbyoass tool
Click to expand...
Click to collapse
i uncheck 3 option (locked bootloader), UART : 921600 and already check com port
still not run