I tried to root my phone from the methods provided from here: http://forum.xda-developers.com/moto-x/general/root-moto-x-att-xt1058-5-1-lpa23-12-21-1-t3164125
I downloaded the necessary files for my specific device. Everything went fine in the flashing process. I booted my phone to check if it was the correct build version, and it was right (LPA23.12-39.7).
I proceeded to the next process, which was running the BLBROKE and RUN_Root file to root my phone. After the RUN_Root process finished ~15 minutes, my phone bootlooped. I tried to re-flash the LPA23.12-39.7 software, but it bootlooped again.
So I performed a hard reset. AFter the hard reset, it bootlooped again and this error showed up: https://drive.google.com/file/d/0BzXaUzs8MoBWSWRWbnh2TG9VTVU/view
I can get to fastboot and Qualcomm Emergency Mode, but anything I have done so far will come back that flashing dead android doll. Any help please? Thanks.
try flashing stock rom, chose the one you were using before brick.
here is guide:
http://forum.xda-developers.com/moto-x/general/guide-moto-x-return-to-100-stock-using-t2446515
firmware link:
https://yadi.sk/d/MCliEyCPfj7ZZ/MOTO.X1/XT1060
buddy means u downgrade your phone from build no. LPAS23.12-39.7-1 ??
ftan299 said:
I tried to root my phone from the methods provided from here: http://forum.xda-developers.com/moto-x/general/root-moto-x-att-xt1058-5-1-lpa23-12-21-1-t3164125
I downloaded the necessary files for my specific device. Everything went fine in the flashing process. I booted my phone to check if it was the correct build version, and it was right (LPA23.12-39.7).
I proceeded to the next process, which was running the BLBROKE and RUN_Root file to root my phone. After the RUN_Root process finished ~15 minutes, my phone bootlooped. I tried to re-flash the LPA23.12-39.7 software, but it bootlooped again.
So I performed a hard reset. AFter the hard reset, it bootlooped again and this error showed up: https://drive.google.com/file/d/0BzXaUzs8MoBWSWRWbnh2TG9VTVU/view
I can get to fastboot and Qualcomm Emergency Mode, but anything I have done so far will come back that flashing dead android doll. Any help please? Thanks.
Click to expand...
Click to collapse
Hello
I encounter exactly the same problem "flashing dead droid no command" after try to root with that method
I tryed to flash the stock rom but I could not down grade to that!
what have you found?? what did you do buddy plz tell me
---------- Post added at 04:04 PM ---------- Previous post was at 03:59 PM ----------
if anybody else should know what should I do to getaway that flashing dead droid plz tell me?
I try to flash the stock rom but I couldnt cuz of downgrade security problem!
Mohsen_zz said:
Hello
I encounter exactly the same problem "flashing dead droid no command" after try to root with that method
I tryed to flash the stock rom but I could not down grade to that!
what have you found?? what did you do buddy plz tell me
---------- Post added at 04:04 PM ---------- Previous post was at 03:59 PM ----------
if anybody else should know what should I do to getaway that flashing dead droid plz tell me?
I try to flash the stock rom but I couldnt cuz of downgrade security problem!
Click to expand...
Click to collapse
I've found this post really helpful
So after I did this first step (flash stock firmware via fastboot) I was able to overcome bootloop issue and install root
Hope this helps!
Related
Well,
I have a Galaxy Note on hands trying to install CM9.1. It was with Official rom ICS 4.0.3. I flashed it without doing the 3 wipes, and after I flashed the rom i tried to wipe data/factory reset. Then the phone would turn off everytime. So, I tought it must be because I didn't flash, then I'm trying to go back to GB, like the tutorial we have in XDA, but I'm stuck at NAND Write Start! Cache.img, and it doesn't proceed, no error messages.
What should I do?
help!
was the 4.0.3 rooted? did you have CWM with kernel or did you use CWM.zip?
nokiamodeln91 said:
was the 4.0.3 rooted? did you have CWM with kernel or did you use CWM.zip?
Click to expand...
Click to collapse
I rooted it first, and after root i used CWM.zip file.
why?
CWM.zip file is known to cause bricks. What kernel where you on? do you remember installing a custom kernel?
---------- Post added at 01:27 AM ---------- Previous post was at 01:26 AM ----------
also it would be good it you can post the screen shot of odin .. how you selected the rom files and where.
nokiamodeln91 said:
CWM.zip file is known to cause bricks. What kernel where you on? do you remember installing a custom kernel?
---------- Post added at 01:27 AM ---------- Previous post was at 01:26 AM ----------
also it would be good it you can post the screen shot of odin .. how you selected the rom files and where.
Click to expand...
Click to collapse
I installed HydraCore 7.0 STD
msedek could be right.. if you can walk us through the procedure on how you tried to install the CM rom.. we could confirm a brick,,
nokiamodeln91 said:
msedek could be right.. if you can walk us through the procedure on how you tried to install the CM rom.. we could confirm a brick,,
Click to expand...
Click to collapse
Well
I was with Official Firmware 4.0.3. Then:
1. Installed Super SU
2. Installed CWM.zip
3. Installed CM9.1
4. Wipe data/factory Reset
5. Auto reboot the device, and styck on boot screen
6. Back to Recovery
6.1 Installed Hydracore 7.0 STD
7. Wipe cache and Wipe Dalwik
8. Tried to wipe Data/factory Reset
9. Auto-reboot and yet locked on boot screen
10 Download Mode
11. trying to install GB official rom and locked in Cache writing.
I need help because it is my boss's phone. I have a galaxy note and because of this procedure that worked fine on mine I did that.
Any help to solve this hard brick?
Anyone? I need help
Really desperate here.
Installing a rom using temp cwm.zip could have done the trick to brick your phone. Anyhow. Could you paste the odin logs.
nokiamodeln91 said:
Installing a rom using temp cwm.zip could have done the trick to brick your phone. Anyhow. Could you paste the odin logs.
Click to expand...
Click to collapse
oh,
I'm not anymore in the PC where I tried Odin. But the logs were pretty usual, stopping at NAND Write Start
like this image
http://forum.xda-developers.com/attachment.php?attachmentid=1224997&stc=1&d=1343392025
And I also tried to install ICS room 4.0.3. That went on till factoryfs.img, then stoped.
Super Brick? Really? How's that possible?
provettirodolfo said:
oh,
I'm not anymore in the PC where I tried Odin. But the logs were pretty usual, stopping at NAND Write Start
like this image
http://forum.xda-developers.com/attachment.php?attachmentid=1224997&stc=1&d=1343392025
And I also tried to install ICS room 4.0.3. That went on till factoryfs.img, then stoped.
Super Brick? Really? How's that possible?
Click to expand...
Click to collapse
The stopping at "factoryfs.img" in combination with using the temporary recovery in cwm.zip is typical for a bricked device.
Please read hg42's thread for checking the bad sectors and for a workaround by repartitioning (this will exclude the bad parts from using it). But first check the eMMC with his method for errors and real confirmation of the brick.
A complete repair is only possible with a replacement of the motherboard by Samsung.
Hey guys, any info on this would be great.
Have a ATT Note 3... It boots into recovery and Download mode..
Basically, I was going to install knoxraid, wiped /system /data, but didn't have the rom file to flash.
Then, rebooted phone, and it will go into stock recovery but not safestrap.
Please help... I know it can't be completely bricked.
I tried unbrick-soft-bricked-att-galaxy-note-3-sm-900a but it fails
(also, I am sure Samsung drivers are installed)
kuttor said:
Hey guys, any info on this would be great.
Have a ATT Note 3... It boots into recovery and Download mode..
Basically, I was going to install knoxraid, wiped /system /data, but didn't have the rom file to flash.
Then, rebooted phone, and it will go into stock recovery but not safestrap.
Please help... I know it can't be completely bricked.
I tried unbrick-soft-bricked-att-galaxy-note-3-sm-900a but it fails
(also, I am sure Samsung drivers are installed)
Click to expand...
Click to collapse
So you can't get the phone to boot normally? What happens when you try to let the phone boot up on it's on without trying to go into recovery or download mode?
Same thing happened to me once.. just took it to my nearest at&t and told them I was upgrading to kit Kat by computer thru kies and that my daughter unplugged my phone during its process and failed and they fixed it for me..free
Sent from my SAMSUNG-SM-N900A using xda app-developers app
kuttor said:
Hey guys, any info on this would be great.
Have a ATT Note 3... It boots into recovery and Download mode..
Basically, I was going to install knoxraid, wiped /system /data, but didn't have the rom file to flash.
Then, rebooted phone, and it will go into stock recovery but not safestrap.
Please help... I know it can't be completely bricked.
I tried unbrick-soft-bricked-att-galaxy-note-3-sm-900a but it fails
(also, I am sure Samsung drivers are installed)
Click to expand...
Click to collapse
I believe you are going to have to Odin back with the Odin JB files. Their is three of them. I see if I can find you more info as to what to do.
---------- Post added at 09:20 PM ---------- Previous post was at 09:06 PM ----------
kuttor said:
Hey guys, any info on this would be great.
Have a ATT Note 3... It boots into recovery and Download mode..
Basically, I was going to install knoxraid, wiped /system /data, but didn't have the rom file to flash.
Then, rebooted phone, and it will go into stock recovery but not safestrap.
Please help... I know it can't be completely bricked.
I tried unbrick-soft-bricked-att-galaxy-note-3-sm-900a but it fails
(also, I am sure Samsung drivers are installed)
Click to expand...
Click to collapse
Here is the like on how to get back to JB.
http://forum.xda-developers.com/showthread.php?t=2707555
htsl said:
I believe you are going to have to Odin back with the Odin JB files. Their is three of them. I see if I can find you more info as to what to do.
---------- Post added at 09:20 PM ---------- Previous post was at 09:06 PM ----------
Here is the like on how to get back to JB.
http://forum.xda-developers.com/showthread.php?t=2707555
Click to expand...
Click to collapse
That would work beautifully, but I don't have safe strap installed and can't get into a ROM...
Basically, I can get into download and stock recovery mode.
Ideas4ya said:
So you can't get the phone to boot normally? What happens when you try to let the phone boot up on it's on without trying to go into recovery or download mode?
Click to expand...
Click to collapse
Nope, I erased system and data... So, I can get into recovery and download mode.
Any help is hugely appreciated....if I could flash safe strap, it would be fine.
kuttor said:
Nope, I erased system and data... So, I can get into recovery and download mode.
Any help is hugely appreciated....if I could flash safe strap, it would be fine.
Click to expand...
Click to collapse
All your gonna have to do is Odin some JB files and your Safestrap should still be on their regardless of you erassing your system data.
---------- Post added at 11:34 PM ---------- Previous post was at 11:32 PM ----------
kuttor said:
Nope, I erased system and data... So, I can get into recovery and download mode.
Any help is hugely appreciated....if I could flash safe strap, it would be fine.
Click to expand...
Click to collapse
What version of SafeStrap did you have installed ? 3.7.1 or 3.7.2
Dude. Wait. If you wiped system you have no rom..All you have to do is use your computer and download a rom and push to your sd card. Then use stock or recovery to flash. Lol. I did this on my nexus once. Anyway it's simple fix.
Sent from my SAMSUNG-SM-N900A using xda app-developers app
kuttor said:
Nope, I erased system and data... So, I can get into recovery and download mode.
Any help is hugely appreciated....if I could flash safe strap, it would be fine.
Click to expand...
Click to collapse
I would say you could revert to MJ5 link http://forum.xda-developers.com/showthread.php?t=2559715. Read it to the T. This will put the MJ5 4.3 back on your phone. You don't need safestrap to revert back to MJ5 method. You can root and install safestrap back on when its installed. Just do steps 1-9 if you don't want to root this method. don't worry about this download link ( https://mega.co.nz/#F!icMTnSQY!bMBNFmUnn2_K8olSTYpwIA (mirror provided by drakeymcmb) i'ts just a mirror for the ml9 fix.image ext4.
YRC123 said:
I would say you could revert to MJ5 link http://forum.xda-developers.com/showthread.php?t=2559715. Read it to the T. This will put the MJ5 4.3 back on your phone. You don't need safestrap to revert back to MJ5 method. You can root and install safestrap back on when its installed. Just do steps 1-9 if you don't want to root this method. don't worry about this download link ( https://mega.co.nz/#F!icMTnSQY!bMBNFmUnn2_K8olSTYpwIA (mirror provided by drakeymcmb) i'ts just a mirror for the ml9 fix.image ext4.
Click to expand...
Click to collapse
Alright, I'll follow this eexact. I am not new to flashing and ROM mods. (Been doing it since the s2). I normally would push via ADB, use a custom recovery and be set. But, just picked up the note 2… and ADB wouldnt detect the phone to push ROM.. (Using ADB device). So, anyways.... I know I have to use ODIN. I know its not fubard because the phone boots into download and stock recovery mode.
Thanks everyone, I really want to get this fix. Luckily I have a nexus 5 as well.
kuttor said:
Alright, I'll follow this eexact. I am not new to flashing and ROM mods. (Been doing it since the s2). I normally would push via ADB, use a custom recovery and be set. But, just picked up the note 2… and ADB wouldnt detect the phone to push ROM.. (Using ADB device). So, anyways.... I know I have to use ODIN. I know its not fubard because the phone boots into download and stock recovery mode.
Thanks everyone, I really want to get this fix. Luckily I have a nexus 5 as well.
Click to expand...
Click to collapse
hold on do you have the note 2 or note 3
jerrycoffman45 said:
hold on do you have the note 2 or note 3
Click to expand...
Click to collapse
Note 3 -- sorry.
kuttor said:
Alright, I'll follow this eexact. I am not new to flashing and ROM mods. (Been doing it since the s2). I normally would push via ADB, use a custom recovery and be set. But, just picked up the note 2… and ADB wouldnt detect the phone to push ROM.. (Using ADB device). So, anyways.... I know I have to use ODIN. I know its not fubard because the phone boots into download and stock recovery mode.
Thanks everyone, I really want to get this fix. Luckily I have a nexus 5 as well.
Click to expand...
Click to collapse
We can't use the old way to get into our or past our bootloaders. If you follow everything on revert to MJ5 steps 1-9 that should give you bootable verse of MJ5 4.3. If you still want root and stay on MJ5 ok. If you want the next software fix then don't root yet then try to get the NB4 patch then you can root with Kingo 1.18.
I tried flashing stock rom in my lenovo A7000a with lollipop version via SP Flash tool but it stuck in bootloop. Then i installed twrp recovery and root it and flash a custom rom "Androim 7" by thinking that it will solve my problem but it didn't. It still get stuck in bootloop. When it get first boot up in custom rom, for first time bootanimation get change a littel and then it get stuck again and every time i flash stock rom or custom rom it get stuck at bootanimation.
Did u enable da/dl with all checksum in spft?if not u must reflash it again with stock rom after enabling them in spft thats it ????????.???? :highfive:
Hit thanks if i helped
Yes, I have checked da dl all checksum in option->download
Then possible it maybe the problem with the stock rom/scatter that u used.try downloading another stock rom with its scatter.it may help
aswinp222 said:
Then possible it maybe the problem with the stock rom/scatter that u used.try downloading another stock rom with its scatter.it may help
Click to expand...
Click to collapse
I did try it by download another stock rom from *Flashing Stock Rom Via SP Flash Tool[Lenovo A7000] by*PrashantRana
But it gets into bootloop.
If bootanimation appears,dont worry just wait for long time.try rebooting with battery replacement etc:both stock and androium takes a hell lot of time to boot for first time.or else you may try flashing CM roms or the nexus MM minimal ported by myself.the wont take much time to boot up :cheers
aswinp222 said:
If bootanimation appears,dont worry just wait for long time.try rebooting with battery replacement etc:both stock and androium takes a hell lot of time to boot for first time.or else you may try flashing CM roms or the nexus MM minimal ported by myself.the wont take much time to boot up :cheers
Click to expand...
Click to collapse
I did as you said above and i downloaded cm13 and istalled it but it didnt work. I have uploaded a video see it. For first time i installed cm13 it goes to cm13 boot animation but in another boot it didnt go to cm13 boot animation. I have provided a video. Have a look.
In fact your phone is a7000a or is it a7000 plus?
---------- Post added at 06:28 AM ---------- Previous post was at 06:27 AM ----------
Which are the fields that you wiped before flashing the rom?
---------- Post added at 06:29 AM ---------- Previous post was at 06:28 AM ----------
In spft which option did u chose?download only/firmware upgrade/format all???
aswinp222 said:
In fact your phone is a7000a or is it a7000 plus?
---------- Post added at 06:28 AM ---------- Previous post was at 06:27 AM ----------
Which are the fields that you wiped before flashing the rom?
---------- Post added at 06:29 AM ---------- Previous post was at 06:28 AM ----------
In spft which option did u chose?download only/firmware upgrade/format all???
Click to expand...
Click to collapse
Both are same. A7000a is the model number and Lenovo A7000 Plus is official name of the Device.
I have tried two methods.
1st Method.
First I flash stock rom then I wipe data/cache/dalvik-cache.
2nd Method
I did same as above in this method but I wipe data/system/cache/dalvik-cache.
I have tried two method
1. Dowload only
2. Firware Upgrade
Third method format all didnt didnt work.
It shows some error.
A7000 and a7000plus are not the same.they got different architecture and kernel.a7000 got a 1.5ghz cpu whereas a7000plus got 1.5ghz,resembling to k3note.make sure you flash the proper firmware.choose firmware upgrade in spft.also i recomment flashing recovery only after first boot.if bootanimation appears it is likely to boot.
aswinp222 said:
A7000 and a7000plus are not the same.they got different architecture and kernel.a7000 got a 1.5ghz cpu whereas a7000plus got 1.5ghz,resembling to k3note.make sure you flash the proper firmware.choose firmware upgrade in spft.also i recomment flashing recovery only after first boot.if bootanimation appears it is likely to boot.
Click to expand...
Click to collapse
Heyy, i got boot up but It again gets reboot and and then its goes to loop. I think the problem is in Cpu Governer. So is there a way to fix cpu frequency?
just ttry flashing daredevil kernel.it got some patches for the same i hope.but i dont think that it helps.give out a try though.
aswinp222 said:
just ttry flashing daredevil kernel.it got some patches for the same i hope.but i dont think that it helps.give out a try though.
Click to expand...
Click to collapse
But the kernel is for marshmallow and my phone has lollipop
Does it wok with Cm13
After I rooted my phone I decided to install a ROM in it. I Found MIUI 7 for the phone and with some instructions it told me to wipe the phone data, use custom recovery and install the .zip and it should be fine. but it went into a boot loop and never booted up. Then I went to download My-ROM v3.3 and still did not work. then I realised it needed the original EMUI to work.
So now I'm stuck here. its been 3 days and my phone still isn't working. my recovery is TWRP.
ImJustChew said:
After I rooted my phone I decided to install a ROM in it. I Found MIUI 7 for the phone and with some instructions it told me to wipe the phone data, use custom recovery and install the .zip and it should be fine. but it went into a boot loop and never booted up. Then I went to download My-ROM v3.3 and still did not work. then I realised it needed the original EMUI to work.
So now I'm stuck here. its been 3 days and my phone still isn't working. my recovery is TWRP.
Click to expand...
Click to collapse
What was the last official version that you were running? Give us as much information as possible.
milan-xda said:
what was the last official version that you were running? Give us as much information as possible.
Click to expand...
Click to collapse
emui 2.3 (b133sp01)
ImJustChew said:
emui 2.3 (b133sp01)
Click to expand...
Click to collapse
That explains why MyRom didn't work. Ok, do you have official UPDATE.APP (B133) on your PC?
No
ImJustChew said:
No
Click to expand...
Click to collapse
I'll dig on the internet later and post a link for you to download.
https://mega.nz/#!RptkFSCa!2y8Ti2qL7ROldNAUZTqecaCUJ03FFWaClD_Hp4Zwuvc
---------- Post added at 03:55 PM ---------- Previous post was at 03:50 PM ----------
Or this one
http://download-c.huawei.com/download/downloadCenter?downloadId=30342&version=54004&siteCode=at
The problem lies after a network change for data connection, subsequently did not recognize any of the simcard.
Its status is NO SERVICE, and dialing * # 06 # does not appear the "IMEI", checking in forums comments that a factory restoration should be done.
In the options of simcard in the phone indicates that "insert a simcard", is as if it recognized neither of the two simcard
I have tested with SM, Naute3g and IMEI.exe and none to served. I have the clipboard phone, can help me to solve this problem. The phone is amazing but has little support.
IMPORTANT: I made a serious mistake by not creating a backup with TWRP, and now I can not return to a previous version.
Please Help me......:crying::crying::crying::crying::crying::crying:
andrestc91 said:
The problem lies after a network change for data connection, subsequently did not recognize any of the simcard.
Its status is NO SERVICE, and dialing * # 06 # does not appear the "IMEI", checking in forums comments that a factory restoration should be done.
In the options of simcard in the phone indicates that "insert a simcard", is as if it recognized neither of the two simcard
I have tested with SM, Naute3g and IMEI.exe and none to served. I have the clipboard phone, can help me to solve this problem. The phone is amazing but has little support.
IMPORTANT: I made a serious mistake by not creating a backup with TWRP, and now I can not return to a previous version.
Please Help me......:crying::crying::crying::crying::crying::crying:
Click to expand...
Click to collapse
Tried Flashing the FULL OTA zip?
Saurabh K said:
Tried Flashing the FULL OTA zip?
Click to expand...
Click to collapse
If you already do it and nothing.
I was investigating and it tells me that it is a problem of the folder EFS, I look for it like root explorer but I do not get it, it means that I lost it?
What can I do in that case?
Reverse back to older stock rom version and install a OTA update through updater app.
Sent from my Le X526 using XDA-Developers mobile app
---------- Post added at 07:46 PM ---------- Previous post was at 07:44 PM ----------
I was having the same issue in my Redmi note 3 flashed stock rom through fastboot but didn't helped n after I got a ota update flashed it n everything was fine again.
Sent from my Le X526 using XDA-Developers mobile app
zeetwo-raj said:
Reverse back to older stock rom version and install a OTA update through updater app.
Sent from my Le X526 using XDA-Developers mobile app
---------- Post added at 07:46 PM ---------- Previous post was at 07:44 PM ----------
I was having the same issue in my Redmi note 3 flashed stock rom through fastboot but didn't helped n after I got a ota update flashed it n everything was fine again.
Sent from my Le X526 using XDA-Developers mobile app
Click to expand...
Click to collapse
With which version of ROM I do, I have no idea which is the oldest??
Don't know much about x620?
Sent from my Le X526 using XDA-Developers mobile app
I can inform you that already solve the problem, I leave the steps to follow for those who have that problem: (It is horrible to suffer this)
1) Download the ROM STOCK 013s (Installed by Fasboot)
2) Have the Recovery Original installed.
3) Go to recovery, Erase data
4) Flash ROM by Fasboot
5) Go from Fastboot to start ROM leaving the power button.
AND READY.......
You will have your NVRAM folder with no problems.
Remember to be careful when installing any recovery if you have smaller versions of ROM to 014s, Look for the tutorials of BB72 ROM.
Thanks for your help
andrestc91 said:
I can inform you that already solve the problem, I leave the steps to follow for those who have that problem: (It is horrible to suffer this)
1) Download the ROM STOCK 013s (Installed by Fasboot)
2) Have the Recovery Original installed.
3) Go to recovery, Erase data
4) Flash ROM by Fasboot
5) Go from Fastboot to start ROM leaving the power button.
AND READY.......
You will have your NVRAM folder with no problems.
Remember to be careful when installing any recovery if you have smaller versions of ROM to 014s, Look for the tutorials of BB72 ROM.
Thanks for your help
Click to expand...
Click to collapse
After getting nvram folder back will i get my imei back or any other method should be followed ? Sorry for noob question.
Not sure how to solve this
lost my Imei. I can not enter factory/download mode... neither by pressing buttons or adb shell..
no custom recovery installed.
booting to stock recovery is working.
my device le s3 X522 USA
Repair using Qualcomm imei tools