help to recover Z1 from hard brick - Xperia Z1 Q&A, Help & Troubleshooting

my z1 doesn't boot or charging
this happened after flashing a custom rom
can i recover it ??
what should i find a replacment for the motherboard ?
sorry for my bad english
hope to find any one to help

Steliyos said:
my z1 doesn't boot or charging
this happened after flashing a custom rom
can i recover it ??
what should i find a replacment for the motherboard ?
sorry for my bad english
hope to find any one to help
Click to expand...
Click to collapse
post stat of your phone -->
1. flashmode & fastboot working?
2. LED when power key is pressed?
3. what rom you flashed?

DectonX said:
post stat of your phone -->
1. flashmode & fastboot working?
2. LED when power key is pressed?
3. what rom you flashed?
Click to expand...
Click to collapse
none of them is working
led isn't working too
DU10.5

yes you can fix your hard brik xperia z1
Steliyos said:
my z1 doesn't boot or charging
this happened after flashing a custom rom
can i recover it ??
what should i find a replacment for the motherboard ?
sorry for my bad english
hope to find any one to help
Click to expand...
Click to collapse
i was facing the same problem with my z1 c6902
only red led while charging
no sony logo
no fastboot mode
pc recognize it in flash mode
how i solved it?
i used xperia companion,
connect your z1 with pc
select repair software
follow the instructions you'll get yur z1 unbricked

vjluvanee said:
i was facing the same problem with my z1 c6902
only red led while charging
no sony logo
no fastboot mode
pc recognize it in flash mode
how i solved it?
i used xperia companion,
connect your z1 with pc
select repair software
follow the instructions you'll get yur z1 unbricked
Click to expand...
Click to collapse
ok the device is seen by the computer but it doesn't boot to download mode
when i connect it shows that there is a device connected to the computer but it's shown as it's a usb input device
can u help me with this?

Have you installed drivers!
---------- Post added at 08:42 PM ---------- Previous post was at 08:40 PM ----------
Steliyos said:
ok the device is seen by the computer but it doesn't boot to download mode
when i connect it shows that there is a device connected to the computer but it's shown as it's a usb input device
can u help me with this?
Click to expand...
Click to collapse
Drivers are installed?
Which os u r using?

vjluvanee said:
Have you installed drivers!
---------- Post added at 08:42 PM ---------- Previous post was at 08:40 PM ----------
Drivers are installed?
Which os u r using?
Click to expand...
Click to collapse
yes of course it's
windows 10 -64 bit

If PC recognizes your phone, can you use that to boot into fastboot mode?
Either use adb command "adb reboot fastboot" in PC
Or press and hold VOLUME_UP button then connect your phone to PC via USB (should see blue LED)

Related

[Q] Help! I think i bricked my x8

Hey guys, sorry if I write bad.
I tried to flash my x8 for put in the rom GingerDX v31b. Anyways... I think my USB cable was broken or something, when I tried to flash baseband 015, it was flashed but then I power on my phone and... Boom! That image appeared: a triangle with a exclamation sign and a phone .
It reboots again and again, my computer doesn't recognize the phone. I need help guys. Sorry for bad writing.
On the other hand.. I have my phone with unlocked bootloader, and I installed so much roms. Any question? sorry if I forgot something. Thank you guys and sorry again if I put the thread in the wrong place.
Francisco Fávaro.
hmm you are sure that flashtool doesnt recognize it?
if you cant use flashtool then go to recovery
i hope this is going to solve he problem
send from xperia x8
little help
Hi,
I've tried to flash my xperia x8 with flashtool but after the flashing, my phone turn off and it won't turn on or connect to the pc. Is it broken for good or there is still hope
noki severgun said:
Hi,
I've tried to flash my xperia x8 with flashtool but after the flashing, my phone turn off and it won't turn on or connect to the pc. Is it broken for good or there is still hope
Click to expand...
Click to collapse
Look under your battery inside the phone. There is a number like 10W34 or 11W10
What is your number?
1.turn of the device
2.open pc companion
3.click support zone
4.click update without connected phone
5.It will ask you about repair(something like that..)
6.click yes
7.wait the program to prepare the pc
8.chose the x8 from devices list
9.wait until download the rom
10.plug the device when the program say to..
CtrlAltDelIrl said:
Look under your battery inside the phone. There is a number like 10W34 or 11W10
What is your number?
Click to expand...
Click to collapse
it is 11w16
Wait...why do you think it's something about bootlader???
just connect to flashtool and recover or if can't be recognized then try with PC Companion else reinstall rom or restore backup with recovery
---------- Post added at 03:44 PM ---------- Previous post was at 03:31 PM ----------
noki severgun said:
Hi,
I've tried to flash my xperia x8 with flashtool but after the flashing, my phone turn off and it won't turn on or connect to the pc. Is it broken for good or there is still hope
Click to expand...
Click to collapse
Ok you flash something but WHAT?
All i know that you have 11W16 and you can't hard brick that(unless you are really..... )
Anyway let's help you out
First of all,how many % did your battery have before flashing?
If under 10% then try to connect the charger
if it done't help keep reading
What did you do with flashtool--->FLASHING or UNLOCKING BOOTLOADER?
If FLASHING: What did you flash,please write down name of file
If UNLOCKING BOOTLOADER:
Try to turn on you phone--->If it won't turn on---->try to connect it to PC in flashmode so FLASHTOOL can recognize it
If FLASHTOOL can't recognize it try with PCC.....if that doesn't work either see does your phone have any Signs of life
If you'r phone is completly dead(no sign of life) than it's probably a HARD BRICK
I hope i helped :good:
big THANKS
8cpaiw said:
Wait...why do you think it's something about bootlader???
just connect to flashtool and recover or if can't be recognized then try with PC Companion else reinstall rom or restore backup with recovery
---------- Post added at 03:44 PM ---------- Previous post was at 03:31 PM ----------
Ok you flash something but WHAT?
All i know that you have 11W16 and you can't hard brick that(unless you are really..... )
Anyway let's help you out
First of all,how many % did your battery have before flashing?
If under 10% then try to connect the charger
if it done't help keep reading
What did you do with flashtool--->FLASHING or UNLOCKING BOOTLOADER?
If FLASHING: What did you flash,please write down name of file
If UNLOCKING BOOTLOADER:
Try to turn on you phone--->If it won't turn on---->try to connect it to PC in flashmode so FLASHTOOL can recognize it
If FLASHTOOL can't recognize it try with PCC.....if that doesn't work either see does your phone have any Signs of life
If you'r phone is completly dead(no sign of life) than it's probably a HARD BRICK
I hope i helped :good:
Click to expand...
Click to collapse
First of all THANKS A LOT for your effort, I mean: really THANKS!!!
So let me tell you a story
It was my forth x8 phone that I've tried to install CM9 on and previously it went very well but yesterday I've did it in a hurry and forget to change the flash file on the flash tool and when I click on the magic button with the flash sign I've realized that the x8 was flashed with x10 firmware the default firmware on the flashtool program (really stupid mistake ). After that the phone turn off and went on haven.
After I cold my head and start to search for new x8 (to replace the broken one) I've realized that the phone has 24 month warranty and the first thing that I did this morning was to return the phone to the shop that was bot from.
I hope that some of you out there had 5 min lol session from my experience in the story, and please, If somebody else thinks that he knows how to do it without reading the manual - this are the consequences!!!
The only way to bring this phone alive is with riff jtag box that I didn't have.
P.S. **** happens
Yes a few people from forum flashed wrong firmware and got hard bricked....amm it's hard brick so they will replace your motherboard
I am glad to help

BootLoop and now Nothing

Hay guys
Heres the deal
I used flashtool 0.9.13.0 and flashed the UK .244 C6603 on my Xperia Z
Then using the method in Excelsus_Z_V5.5.7 to change the kernel to the .423
After words I used the Root tool DoomLord Ver18 to root the device and then the TWRP till now all is GOOD
When I flashed the ROM the Recovery gave an error mid way through the setup
So when I restarted the device I got stuck
Now I have the Sony logo all the time
I can't even go to flash mode to reFlash a stock TFT
Please Help.....
Fastbootmode? Volum up & plug in usb
---------- Post added at 03:57 PM ---------- Previous post was at 03:56 PM ----------
Do you tryed to flash back to stock rom with flashtool or SUS?
gripfly said:
Fastbootmode? Volum up & plug in usb
---------- Post added at 03:57 PM ---------- Previous post was at 03:56 PM ----------
Do you tryed to flash back to stock rom with flashtool or SUS?
Click to expand...
Click to collapse
I cant get into flash mode
it keeps rebooting
and at best I get a blank screen with a red LED
sshashlan said:
I cant get into flash mode
it keeps rebooting
and at best I get a blank screen with a red LED
Click to expand...
Click to collapse
vul up + power will restart your phone, keep it pressed both for more than 10 sec and it will shutdown your phone hardwarely! then you can go to flashmode, fastboot and etc.
sijav said:
vul up + power will restart your phone, keep it pressed both for more than 10 sec and it will shutdown your phone hardwarely! then you can go to flashmode, fastboot and etc.
Click to expand...
Click to collapse
NO nothing
the phone goes OFF but when I connect the USB the RED LED comes UP and NO Flash Mode
sshashlan said:
NO nothing
the phone goes OFF but when I connect the USB the RED LED comes UP and NO Flash Mode
Click to expand...
Click to collapse
I'm not sure if you doing this the right way,
1. you must hold down the vul down
2. and then connect the USB!
3. make sure your drivers are installed and your pc find your phone!
sijav said:
I'm not sure if you doing this the right way,
1. you must hold down the vul down
2. and then connect the USB!
3. make sure your drivers are installed and your pc find your phone!
Click to expand...
Click to collapse
Nop
I know how to do this
I tried to do it more than once by pressing the Vol Down for the flash mode and/or Vol UP for the fastboot mode
yet NOTHING ;(
sshashlan said:
I cant get into flash mode
it keeps rebooting
and at best I get a blank screen with a red LED
Click to expand...
Click to collapse
For fastboot mode you dont need flashmode..
Open flashtool
Klick on fastbootmode
Connect phone with holding volume up button
What happens now?
gripfly said:
For fastboot mode you dont need flashmode..
Open flashtool
Klick on fastbootmode
Connect phone with holding volume up button
What happens now?
Click to expand...
Click to collapse
I m getting the same thing with the red LED
on Flashtool LOG
04/047/2013 16:47:08 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/049/2013 16:49:32 - INFO - Device disconnected
04/049/2013 18:49:06 - INFO - Device connected with USB debugging off
04/049/2013 18:49:06 - INFO - For 2011 devices line, be sure you are not in MTP mode
04/051/2013 18:51:22 - INFO - Device disconnected
it stays blank for some time and it comes back up with the Sony logo and back with the LOOP
sshashlan said:
NO nothing
the phone goes OFF but when I connect the USB the RED LED comes UP and NO Flash Mode
Click to expand...
Click to collapse
Only Off and no restart??
EDIT:
http://forum.xda-developers.com/showthread.php?t=2229250
give a look at this thread, If you need your phone quckly. Now I don't have more time for next hours.
gripfly said:
Only Off and no restart??
EDIT:
http://forum.xda-developers.com/showthread.php?t=2229250
Give a look at this thread, If you need your phone quickly. Now I don't have more time for next hours.
Click to expand...
Click to collapse
Man Thank you So Much
It appears I had a soft Break
but this link saved Me
All OF YOU
THANK YOU
sshashlan said:
Man Thank you So Much
It appears I had a soft Break
but this link saved Me
All OF YOU
THANK YOU
Click to expand...
Click to collapse
You're welcome

[Q] Rare Case - Red LED always on while screen is on

Alright. My brother bought a used Xperia Z about 2 weeks ago. After using it some days, suddenly this happened. The red LED always stays on while the screen is on. And this is a rare problem. I don't see any problems like this before in XDA. The phone is not rooted nor the bootloader has been unlocked. Can someone help fix this problem, or tell me what partition is damaged, etc? I can't confirm this is a HW damage coz it's not dropped, or punched, etc The red LED acts normally if the screen is off (e.g. while charging, notification, etc).
Vinardo_ZzZ 2000 said:
Alright. My brother bought a used Xperia Z about 2 weeks ago. After using it some days, suddenly this happened. The red LED always stays on while the screen is on. And this is a rare problem. I don't see any problems like this before in XDA. The phone is not rooted nor the bootloader has been unlocked. Can someone help fix this problem, or tell me what partition is damaged, etc? I can't confirm this is a HW damage coz it's not dropped, or punched, etc The red LED acts normally if the screen is off (e.g. while charging, notification, etc).
Click to expand...
Click to collapse
Factory reset will solve your issue most probably :good:
androidtweaker1 said:
Factory reset will solve your issue most probably :good:
Click to expand...
Click to collapse
My bro tried it many times. Using PC Companion doesn't work either...
Vinardo_ZzZ 2000 said:
My bro tried it many times. Using PC Companion doesn't work either...
Click to expand...
Click to collapse
bro you can try flashing stock rom again.
---------- Post added at 12:51 PM ---------- Previous post was at 12:45 PM ----------
Vinardo_ZzZ 2000 said:
My bro tried it many times. Using PC Companion doesn't work either...
Click to expand...
Click to collapse
download 4.4.2 official ftf from here https://mega.co.nz/#!Bk0XlY7S!7rhLzB...omXmNTcrI3h4Vc
download flashtool from here http://www.flashtool.net/download.php
after installing flashtool go to c: then flashtool folder
go to drivers install from exe file, select flashboot and fastboot and finish installation
open flashtool, click on the lightning button, select flashboot.
select the firmware downloaded(make sure you cut paste the ftf file in the firmware folder of flashtool folder)
put phone in flashmode when prompted(hold power down key and connect usb)
once flashing is complete disconnect and switch on the phone
androidtweaker1 said:
bro you can try flashing stock rom again.
---------- Post added at 12:51 PM ---------- Previous post was at 12:45 PM ----------
download 4.4.2 official ftf from here https://mega.co.nz/#!Bk0XlY7S!7rhLzB...omXmNTcrI3h4Vc
download flashtool from here http://www.flashtool.net/download.php
after installing flashtool go to c: then flashtool folder
go to drivers install from exe file, select flashboot and fastboot and finish installation
open flashtool, click on the lightning button, select flashboot.
select the firmware downloaded(make sure you cut paste the ftf file in the firmware folder of flashtool folder)
put phone in flashmode when prompted(hold power down key and connect usb)
once flashing is complete disconnect and switch on the phone
Click to expand...
Click to collapse
I think he already tried flashing with flash mode too. I will ask him later. Thanks for your suggestion
Vinardo_ZzZ 2000 said:
I think he already tried flashing with flash mode too. I will ask him later. Thanks for your suggestion
Click to expand...
Click to collapse
ok

Bricked z1 Red light blinks UB C6903

Please i need help, i hard bricked my z1 c6903 ,restoring a backup with unlocked bootloader , this time the pone is totally dead. When in plugg in it blinks a red light.Im reading all about this and im a bit confused ,can anyone help me please?I really appreciate if u can.Best regards
SANTUMIL said:
Please i need help, i hard bricked my z1 c6903 ,restoring a backup with unlocked bootloader , this time the pone is totally dead. When in plugg in it blinks a red light.Im reading all about this and im a bit confused ,can anyone help me please?I really appreciate if u can.Best regards
Click to expand...
Click to collapse
Charge it for good 1-2 hours then flash stock firmware using flashtool..
kathanpatel1001 said:
Charge it for good 1-2 hours then flash stock firmware using flashtool..
Click to expand...
Click to collapse
Flashtools ,dont recognize my phone,it oly blinks red light when its charging
SANTUMIL said:
Flashtools ,dont recognize my phone,it oly blinks red light when its charging
Click to expand...
Click to collapse
Its most likely to be bad usb cable and or drivers..keep it on charger and use different usb cable also install drivers properly windows 8+ requires additional steps in driver installation google it..
kathanpatel1001 said:
Its most likely to be bad usb cable and or drivers..keep it on charger and use different usb cable also install drivers properly windows 8+ requires additional steps in driver installation google it..
Click to expand...
Click to collapse
Im on win7 64x,everything was ok after restore a rom from twrp,drivers was sucefully installed ,and after this brick i was able to use flashtools ,so.. i think usb cable and drivers are OK. When i plug it to wall or usb ,only blinks a red light ,i tryed several keys combinations and nothing happens.
SANTUMIL said:
Im on win7 64x,everything was ok after restore a rom from twrp,drivers was sucefully installed ,and after this brick i was able to use flashtools ,so.. i think usb cable and drivers are OK. When i plug it to wall or usb ,only blinks a red light ,i tryed several keys combinations and nothing happens.
Click to expand...
Click to collapse
plug it into the wall and leave it on charge overnight, don't touch it. Try connecting in the morning, should work.
AnrgKrshn said:
plug it into the wall and leave it on charge overnight, don't touch it. Try connecting in the morning, should work.
Click to expand...
Click to collapse
Thxs but the phone is dead,nothing that i search it works.:crying::crying: And btw i got bricked so many times on LB and always i could flash it again,this issue im surely it was for being ULB
SANTUMIL said:
Thxs but the phone is dead,nothing that i search it works.:crying::crying: And btw i got bricked so many times on LB and always i could flash it again,this issue im surely it was for being ULB
Click to expand...
Click to collapse
UB is usually easier to recover cause you can fastboot any custom kernel to recover the phone.
---------- Post added at 04:44 PM ---------- Previous post was at 04:36 PM ----------
http://forum.xda-developers.com/showthread.php?t=2574764
AnrgKrshn said:
UB is usually easier to recover cause you can fastboot any custom kernel to recover the phone.
---------- Post added at 04:44 PM ---------- Previous post was at 04:36 PM ----------
http://forum.xda-developers.com/showthread.php?t=2574764
Click to expand...
Click to collapse
Same issue with mine, tried all and nothing worked. Finally gave it to sony center and told that while upgrading to LP this happened. They replaced pcb , back panel etc and gave an almost new phone for free bcoz it was in warranty.

Your device is corrupt It can't be trusted and will not boot please help

Your device is corrupt It can't be trusted and will not boot please help
Sony Xperia 1 mark 2
Do a software repair using Xperia Companion on a computer. Alternatively, you can do a full wipe using Flashtool or newflasher.
Whe using xperia 1 i have this problem.this happen because flash using bad cable
Thanks So much it worked
iArvee said:
Do a software repair using Xperia Companion on a computer. Alternatively, you can do a full wipe using Flashtool or newflasher.
Click to expand...
Click to collapse
i Used new-flasher to flash firmware instead , because i was on low battery couldn't use Sony Xperia companion.
sony1xps said:
Your device is corrupt It can't be trusted and will not boot please help
Sony Xperia 1 mark 2
Click to expand...
Click to collapse
we need some more information to help you.
What did you do to cause this error?
In most cases you can recover from this error so don't panic.
Lennyuk said:
we need some more information to help you.
What did you do to cause this error?
Click to expand...
Click to collapse
Different from the OP, but I'm facing the same issue.... Trying to flash the XQ-AT51 firmware on XQ-AT52. Tried to use flashtool on one computer got a "bundle does not match connected device error". Tried a different computer using newflasher. First I followed some instructions involving removing the .ta files, flashed. That's when I first got the boot loop and corrupt screen. Then I downloaded the firmware again and left everything in the folder except "persist_X-FLASH-ALL-2389.sin" and got the same result.
Tried a different cable. Xperia Companion just says the device is locked. So does Emma. Just stuck. ?
Why don't you download XQ-AT52 Firmware instead of XQ-AT51 ,
and flash it using newflasher ?
Here is the guide for newflasher just to double check. w w w.xperiablog.net/2018/01/28/newflasher-guide-to-install-new-firmware-for-xperia-xz-premium-xz1-and-more/
UwUzzzz said:
Why don't you download XQ-AT52 Firmware instead of XQ-AT51
Click to expand...
Click to collapse
Because I'm trying to install the US version....
---------- Post added at 04:13 AM ---------- Previous post was at 03:47 AM ----------
Tried to reflash AT52.... Same thing.... I appear to be screwed.
oo-long said:
Because I'm trying to install the US version....
---------- Post added at 04:13 AM ---------- Previous post was at 03:47 AM ----------
Tried to reflash AT52.... Same thing.... I appear to be screwed.
Click to expand...
Click to collapse
Okay I was able to repair it using the Xperia Companion....
I didn't realized that I needed to start the repair before the phone was plugged in. ?
---------- Post added at 11:29 PM ---------- Previous post was at 10:44 PM ----------
And in case anyone else is in the same situation. I re-flash the device with the AT51 firmware and everything worked fine. I'm now using the US firmware on the international AT52 version of the device.
After the repair through Xperia Companion. I just re-ran the same thing as last time (with all the .ta files without the persist file) after setting up the device and turning on USB debugging again. However this time I didn't get a prompt halfway through about flashing the persist partition.
Now everything works on the US firmware. Not sure why. This is literally my fist Android device so I know very little about all this. Just glad to have a working phone again. ?
anyone can help me
i have the same problem...
Anybody figure out why Xperia Companion fails as shown in pic above? My battery is charged too so not sure why it says needs to charge battery in Xperia Companion.
I'm also getting that error message as shown above in post # 11 when trying to repair via the Xperia Companion. Any help would be great!
Me too, having the same problem with my Xperia 1 SOV-40.
I had the same problem with my Xperia 5 ii after I re-locked the bootloader using fastboot (fastboot oem lock).
I could fix the problem with Xperia Companion. Here is what I did [maybe labels are not exactly correct, my interface is in german]:
Pre-requisites:
I did not use the original Sony USB cable, but a third party cable from Anker, also worked
Disconnect device from computer
Steps to fix:
Install and start Xperia Companion
Click "software repair"
On the bottom click "My device is not detected or is a Smartwatch 3"
Choose your device, click "Xperia smartphone or tablet"
Follow steps on the screen:
Disconnect and power off device (should already be)
Press and hold volume down
Connect device via USB cable, still hold volume down, the notification LED will turn green
Repair starts
Wait about 10 to 20 minutes until repair is finished
Screen will stay black and notification LED will stay green during the whole procedure
After these steps, Xperia Companion showed a success message and my device turned off. I disconnected the cable and started it (press and hold power button for about 1 second). The device first only turned on the notification LED in green, screen stayed black. After about 5 to 10 seconds, the device turned off again. I started it again (press and hold power button for about 1 second) until it vibrates, and it started normally.
Of course the device was reset and all data was wiped. For me this was no problem, as I anyway resetted it before.
Hope that helps
blegs said:
Whe using xperia 1 i have this problem.this happen because flash using bad cable
Click to expand...
Click to collapse
A few hours ago I suffered this, the problem with cable! I tormented 10 hours to look for other solutions to put the "ROM", being the official version (emma flasher) does not work! But it didn't work because of the cable (it was a "Baseus" cable, it was ok, but I think it was too long, 3 meters: D .
sony1xps said:
Your device is corrupt It can't be trusted and will not boot please help
Sony Xperia 1 mark 2
Click to expand...
Click to collapse
i have same problem ..plz help me
i have same problem ..please help me

Categories

Resources