Related
Thanks to Kevlar-Source there is now a disassembly procedure at
http://wiki.xda-developers.com/index.php?pagename=DIS_BA
Whoever wants change the LCD on BA has can buy the spare part at :
http://www.pdasmart.com/pdaphonexda2s.htm
or send the Ba for a Full Service Repairs to :
http://www.pocketpctechs.com/main~unit~Qtek_9090-257~area~repairs~item~XDA-TS03.htm
http://www.apexlaptops.co.uk/xda.htm
Unforunately I choosed the first way and now I am stuck on the fact that after installing the new Lcd screen from PDASMART the screen is completely blank , even if the Qtek seems to work , lights sounds etc
There are differences between the two LCD , connector and label , I am attaching a picture hoping someone will help in finding the cause of the problem ...
I wrote a couple of mail to PDASMART but I did not receive any answer to date
Ciao !!
Anyone know where I can buy steal/etc. one of those screws on the side of the BA?
Gbrand said:
There are differences between the two LCD , connector and label , I am attaching a picture hoping someone will help in finding the cause of the problem ...
Click to expand...
Click to collapse
Hi,
what is your BA board id ?
http://wiki.xda-developers.com/index.php?pagename=BlueangelBoardIDs
http://wiki.xda-developers.com/index.php?pagename=BlueangelLCD
60H00018-00 and
60H00033-00 are obviously different.
what is your BA board id ?
Click to expand...
Click to collapse
I dont know , I dont have Linux , and beside that the screen is absolutely blank ! Anyway, is an Italian QTEK 9090 from DAANGARD , if there is an alternative way to know Board Id , please let me know !javascript:emoticon('')
Very Happy
As you say is obvious the two LCD have different Sn , but as I am not an HW tech maybe someone on the Forum knows if they are compatible
The fact is that the LCD matter is quite misterious , is a piece of HW that easily breaks , and according to my knoweledge there is only one supplier shipping the part , PDASMART
What I did is buy the part from PDASMART , install it , test that it does not work , at least on my Qtek , write back to PDASMART a couple of Mail and I am still waiting for a replay !! javascript:emoticon(':evil:')
Evil or Very Mad
To be honest I have the doubt that reassenbling the LCD I could have made something incorrect , but the reassembly procedure is well described on WIKI ...
Would not be bad if we can find a reliable source of spare LCD on the web and collect some info for WIKI .
Gbrand said:
if there is an alternative way to know Board Id , please let me know
Click to expand...
Click to collapse
Run haret.exe and post the 'dump gpio bagpio' output (the bagpio file).
http://sdgsystems.com/pub/ipaq/hx4700/starterkit/20050611/
What i really hate is that the damn fsckers who
sell the LCDs have really no idea what they are selling!!!
Gbrand said:
There are differences between the two LCD , connector and label , I am attaching a picture hoping someone will help in finding the cause of the problem ...
Click to expand...
Click to collapse
Left one is a Toppoly LCD (see http://www.toppoly.com/toppoly/Product/TD035STEC1.asp ) used in boardid 0x6 BAs, right one is a Sony one (ACX502BMV) used in boardid 0x5
Don't know how to change the board id, maybe some solder pads.
Left one is a Toppoly LCD (see http://www.toppoly.com/toppoly/Product/TD035STEC1.asp ) used in boardid 0x6 BAs, right one is a Sony one (ACX502BMV) used in boardid 0x5.
Click to expand...
Click to collapse
So , my board id is 0x6 and PDASMART sent me a 0x5 Boardid LCD ,
Don't know how to change the board id, maybe some solder pads
Click to expand...
Click to collapse
Anywone around knows how to solve the problem ?
PDASMART is quite latitant ! javascript:emoticon('')
Sad
Added picture of the toppoly and sony LCD on
http://wiki.xda-developers.com/index.php?pagename=BlueangelLCD
Hope is the right place .
But still stuck on blank LCD .
Is board id something can be changed ?
How can I get out of this damned story ?
Gbrand said:
Is board id something can be changed ?
How can I get out of this damned story ?
Click to expand...
Click to collapse
It is interesting to force the id=5 setting in Linux
and check if the device will be working properly.
Then you can simply patch the wince-relevant binaries.
BTW, can you add your model to the boardIDs wiki page ?
BTW, can you add your model to the boardIDs wiki page ?
Click to expand...
Click to collapse
done !
I can work on Qtek only through PC and SOTI Pocket Controller-Professional , I am afraid to install Linux , absolutely unknown to me , in this situation .
I had to force in Wince to not execute WELCOME , which take care of screen alligment , if WELCOME execute I am stuck on trying forever to allign the screen that cannot be alligned .
The most annoying thing is that PDASMART has not replied to me yet !!!
I asked for return the LCD back to them http://www.pdasmart.com/terms.htm
but to date no answer !
anyone gone and bought an LCD to find it's the wrong model?
If so please PM me and I might buy it off you if it's the right model for me!
Cheers!
9090 (ITA DAANGARD) display with problem
Hi, Sorry but You're not "the one". I've the same pda (daangard sold) and similar problem in the same city.
Time to time display blocks, needs hard reset (this is what I have done but not sure it was necessary), and " I was stuck on trying forever to allign the screen that cannot be alligned- it was need half hour".
About - "I had to force in Wince to not execute WELCOME" - How did you that?
I tought to take the pda, waiting one of my neighbour (that obviously i don't like) and use the pda as a stone (two birds with one act). If you want i could "take off" the display before that 8).
How about your bluetooth range and stability?
Best regards
Sergio
Gbrand said:
BTW, can you add your model to the boardIDs wiki page ?
Click to expand...
Click to collapse
done !
I can work on Qtek only through PC and SOTI Pocket Controller-Professional , I am afraid to install Linux , absolutely unknown to me , in this situation .
I had to force in Wince to not execute WELCOME , which take care of screen alligment , if WELCOME execute I am stuck on trying forever to allign the screen that cannot be alligned .
The most annoying thing is that PDASMART has not replied to me yet !!!
I asked for return the LCD back to them http://www.pdasmart.com/terms.htm
but to date no answer !
Click to expand...
Click to collapse
qteck 9090 not alignable
hello I have a 9090. It haS alwayS been a probelm : The StyluS iS no more aligned after 30 SecondeS or 1 minuteS of uSe Since i have it.
IS it common with thiS model ? Or my Screen iS broken?
That why I never really uSe thiS phone becauSe uSing the mini keyboard iS not very eaSy. If the Screen iS defect can you provide me an URL where to buy a new one? IS it epanSive?
thankS a lot.
How to replace the PCB cable of the LCD to the motherboard???
Mine is cutted... Were to buy one even if used?
Well .. I had to fix it... LCD anyone??
As I got no answer I bought a new LCD.. all OK now!.
If anyone needs a GOOD LCD with a cutted cable, please let me know.
cox said:
Hi, Sorry but You're not "the one". I've the same pda (daangard sold) and similar problem in the same city.
Time to time display blocks, needs hard reset (this is what I have done but not sure it was necessary), and " I was stuck on trying forever to allign the screen that cannot be alligned- it was need half hour".
About - "I had to force in Wince to not execute WELCOME" - How did you that?
I tought to take the pda, waiting one of my neighbour (that obviously i don't like) and use the pda as a stone (two birds with one act). If you want i could "take off" the display before that 8).
How about your bluetooth range and stability?
Best regards
Sergio
Click to expand...
Click to collapse
I know this is an old topic, but 2 (3 with me) have/had the same problem..
Me too, I got only white screen, after I had only replaced the full housing case.. ..reunited all the parts, turned it on, and nothing, only white screen..
which was your solution? Come avete risolto?
Guys according to this Board ID and Screen ID table;
My SPV M2000 BlueAngel has 0x5 Board Id and can work with Sony LCD unit. But I had a Sony LCD unit brand new one from my previous i-mate pda2k; and device starts with a black screen. I can see energy is coming to screen but it never turns on.
Is there anyway to solve this problem?
Yes, it restart itself every few minutes.
I got this problem since the day I bought it about 2 weeks ago. I sent it back to the seller and they did something to make it work fine till now.
The same problem comes back.
I observed the problem and here are the facts.
1. It restart a few seconds after it turn off the screen. That's the power settings.
On batter power: Turn off device if not used for = 40 sec
So about 5 sec after the screen is off, it restart.
If I plug it to USB charging mode or sync mode, it get extremely hot but never restart, because it never turn off (not on battery power).
If I untick "Turn off device if not used for"... it also get extremely hot but never restart. It does drain too much battery, of course.
2. It's abnormally slower than other devices. My father bought 3 HT Diamonds at once. 2 works fine so I can compare them. They have the same firmware, same model, everything is the same, but this one got this problem.
3. It happened like this for both Chinese firmware and English firmware. But when the seller fixed it, they did installed Chinese firmware.
Device information:
Version:
ROM version: 1.93.831.1 WWE
ROM date: 07/18/08
Radio version: 1.00.25.05
Protocol version: 52.29.25.12H
Hardware
CPU: QUALCOMM(R) 7201A
Speed: 528MHz
RAM size: 192 MB
Flash size: 256 MB
Internal Storage: 3823.48 MB
Data bus: 32 bits
Storage size: 82.31 MB
Display resolution: 480x640
Colors: 65536
Bluetooth version: 2.0/2.0+EDR
Bluetooth address: 00: 17: 83: D4: E7: 56
Does anyone know how to deal with this?
Still Restarting
Does anyone have answer to my previous question? So sad that the phone keep restarting itself like this. Is there a new ROM that fix the problem?
Thousands of thanks to person who shred some light. Thanks.
Did you try a hard reset?
Yes
pedmond said:
Did you try a hard reset?
Click to expand...
Click to collapse
Yes, kinda tried that many times.
Did reflashed the ROM 2 times too.
Did tried 2 different language ROM too, 1 English and 1 Chinese.
It looks like you have a defective unit then
I had same problem with O2 Neo then I sold it ASAP
I have also got the same problem, I have tried many ways, Installed dutty's roms also, but the thig is, its not rom fault. its internal storage problem. You have to hard reset all, clear all data in internal storage too.
go to setting > sytem > clear storage
has this problem been SOLVED????
go to setting > sytem > clear storage
Click to expand...
Click to collapse
that didn't work for me.
This fixed my problem after much troubleshooting. I though it wouldn't work, assumed it was hardware problem.
flashed to newest stock rom twice.
flashed to custom rom (mighty) twice.
Don't forget to unlock where need be.
binh said:
Yes, it restart itself every few minutes.
I got this problem since the day I bought it about 2 weeks ago. I sent it back to the seller and they did something to make it work fine till now.
The same problem comes back.
I observed the problem and here are the facts.
1. It restart a few seconds after it turn off the screen. That's the power settings.
On batter power: Turn off device if not used for = 40 sec
So about 5 sec after the screen is off, it restart.
If I plug it to USB charging mode or sync mode, it get extremely hot but never restart, because it never turn off (not on battery power).
If I untick "Turn off device if not used for"... it also get extremely hot but never restart. It does drain too much battery, of course.
2. It's abnormally slower than other devices. My father bought 3 HT Diamonds at once. 2 works fine so I can compare them. They have the same firmware, same model, everything is the same, but this one got this problem.
3. It happened like this for both Chinese firmware and English firmware. But when the seller fixed it, they did installed Chinese firmware.
Device information:
Version:
ROM version: 1.93.831.1 WWE
ROM date: 07/18/08
Radio version: 1.00.25.05
Protocol version: 52.29.25.12H
Hardware
CPU: QUALCOMM(R) 7201A
Speed: 528MHz
RAM size: 192 MB
Flash size: 256 MB
Internal Storage: 3823.48 MB
Data bus: 32 bits
Storage size: 82.31 MB
Display resolution: 480x640
Colors: 65536
Bluetooth version: 2.0/2.0+EDR
Bluetooth address: 00: 17: 83: D4: E7: 56
Does anyone know how to deal with this?
Click to expand...
Click to collapse
Hi binh,
My Touch Diamond does the same. It has the same Radio and Protocol version, but the ROM is 1.93.00.0.
My Problem occurs after the instalation of the IGO navigation software. Untill that it was o.k. After a hard reset is everything o.k. untill the instalation of the IGO. Just tell us if You are using any navigation software?
Thank You in advance.
This should work
Have a touch pro and faced a similar issue . Did a lot of googling and finally found a solution that works . Apparently this happens if the batttery contacts (the small golden colour pins which come in contact with the phone battery ) at the backside are either bent or crimped . Straighten them and it should work like a charm . This is because of faulty battery contacts the phone goes into a restarting loop.
Hope this helps
Well... try this and let me know:
Replace your phone's battery with a genuine new htc battery..
This restarting issue had occurred with my Sony Ericsson w800
The thing is that every li-ion battery has a safety cut out circuit embedded in it. It is there to protect the battery from heating up in case of short circuit. It breaks the power for a few micro seconds and turns it back on. That circuit gets weak with time and eventually it assumes even a little load as a short circuit. So when you use your cellular radio [phone's communication system], it puts an immense load over the battery and the cut out circuit assumes as if the battery is being short circuited. So it cuts out the power for a few micro seconds and turns it back on. The phone, on the other hand, assumes of it as a short power failure so it reboots.
:::::::::::::::::::
I am very eager to know if thats the problem with your device.
Also if you have a non genuine battery, then it would be having a weak cut-out circuit.
Hey guys , i bought the Samsung Galaxy Tab S2 8.0' from thailand this is the full Specs:
On the box stated : SM-T715YZDETHL
in the about menu stated : SM-T715Y
Build Number : MMB29K.T715YDXU2BPJ1
T715YDXU2BPE3
android 6.0.1
- i didn't touch it , just update (no root nor anything alike)
the first time i opened the device ( which was sealed ofc ) it had a issue that some texts got dissapeared (you see like W lc om instead of Welcome and some more stuff like that) , black covers layers of the screen some times and a few more strange stuff.
i cannot send it to services of thailand because i dont live there nor around there.
once updated to 6.0.1 seems like the first problem solved but i still cannot play any 3D Game (it just crash on start , also i get poor results on some benchmark tests) , seems like an hardware issue but i wanted to make sure its not a software issue.
i wanted to install an english version or internetional version 6.0.1 android but cannot find any info on it. and not sure about the thai version i have.
so , what roms can i flash ? , do i need to do bootloader unlock first or something like that ?
thanks alot guys - you guys are my last hope...
well.. now it wont even charge.. (it's just giving a Red X icon on the battery while connected to the charger (all original and came with it!)
it started 2 minutes after i added a new SIM Card somehow ..
i tried 4 diffrent chargers (which works on other phones and tablets).
cannot burn a new rom because the usb wont regonize even in Download mode.
any idea ?
(i tried to blow air inside the charge pin and clean it.. all stayed the same sadly..) .
thanks guys.
Jesus..
well got past the NO Charge/USB problem.
and also rooted my device.
seems like i have hardware issues with the GPU (Mali) ..
naty106135 said:
well.. now it wont even charge.. (it's just giving a Red X icon on the battery while connected to the charger (all original and came with it!)
it started 2 minutes after i added a new SIM Card somehow ..
i tried 4 diffrent chargers (which works on other phones and tablets).
cannot burn a new rom because the usb wont regonize even in Download mode.
any idea ?
(i tried to blow air inside the charge pin and clean it.. all stayed the same sadly..) .
thanks guys.
Click to expand...
Click to collapse
im having the same problem after installing cyanogen rom in t815y
BUMP
Hy, there ! My Z1 Compact had the screen a little bit curved on the outside, meaning that when I pushed against the middle of the screen , the screen went back into the right position.
The phone was bought online from UK before Sony launched it in Romania. So, no guarantee. The screen cracked at some point. I have image, I have touch below the crack, but above the crack no touch.
1 - Why did the screen curve outside ? Is it the battery ( got bigger because of the heating up while using GPS , playing or charging ) ? Or is it common that the screen detach itself ?
2 - Is it worth to replace the screen ? All the shops told me there aren`t any original screens, only OEMs. Some say the image is the same, others say it is not. But what`s more upsetting is that some say that these new OEM screens crack very easy, even when they`re in the pockets or in your hand, or crack at first drop. Is there anyone here who replaced the screen ? What should I do ? What to expect from these OEM screens ? Is there anything else I should be aware about ?
3 - I cannot unlock the phone because the starting character of the password unlocking screen is above the crack . What can I do to recover the data from it ? SMS, Contacts , pictures..
4 - Should I replace the original battery with a new OEM one or these are worse that a 2 year old original battery ?
Thank you in advance !
PS : the only problems I had with Z1 C were :
a - If I was in a call and somebody else callled me, if I ended the 1st call to engage in the 2nd call, the other person could never hear me, that resulting in dropping the call and calling again. The same problem I had with my Z1 also.
b - ocassionally restarts, but those I ve see an ALL my android phones
c - when talking in speaker mode, you cannot hear well and the other person could not hear at all , most of the times.
d - the max volume of the music was kinda 1/2 compared to samsung phones. It s not the speakers that upset me, but the low volume when connecting the phone to sound system, for example.
e - it got very very hot when using GPS - and the battery drained in 3 hours tops of continuous use of GPS and internet mobile.
My Z1 is another story. I bought it for my former job, because my employer could not afford to buy me a phone. It was SH, from a shop, originally sold by Vodafone Germany. It had some issues and the bloatware from vodafone was annoying, so I decided to take back to the shop ( i had 3 months guarantee ) to resoft the phone. After a week I got the phone back with the original software. But the phone started working worse and worse, because of The Intermittent Touch Screen Issue - that I find out about only after I got very mad 2 nights ago and smashed the phone to the floor. The screen is now in a million pieces. I am very sorry now, my both phones are unusable and I don`t know what to do and if it`s worth to repair them. Can this The Intermittent Touch Screen Issue be fixed ? I mean the phone wrote iself or deleted everything I was writing or I could not press some letters on the keyboard or one letter remained pressed for eternity ... everytime I had to press power button of and on again until the phone started working properly again. That`s why I got so mad ... Has anyone experienced these problems with their Sony ? Is there any solution ?
Sorry for the long text, but I really need some good advice now.
Thank you for your patience and possible advice !
Hi all
I have recently purchased an Eonon branded PX3 model number GA8162 (Android 7.1 / 2GB ram)
Sometimes when turning the car off the stereo will not wake the next time you start the car. It is completely unresponsive including the reset button. There is nothing you can do to wake the stereo until about 12 hours (or so) passes and then it will boot up fine.
When it happens, all the rest button does is make the backlighted buttons light up, and they turn off as soon as the reset button is released. You can make this happen to the headunit when the ignition is off also.
It doesn't always do this, only occasionally and I don't know what it causing it. I have installed Malyusk's custom rom which I would hope solve it, and even installed a new MCU that the seller provided to me.. Neither have worked.
I do not think it is a problem with my car as my old Kit-Kat based headunit never had any problems.
Has any one had any experience of anything like this? Is it a hardware issue, or does anyone have a workaround? I dont really want to send it back due to the cost and how long it will take to get a replacement!
Many thanks
GA8162
Hello, I'm very new to this and while I don't currently have problems I'd be interested to know which MCU you updated to, the MTCE_WWW search doesn't really bring up any results. I have the same unit as yourself and would love to update it. Cheers
I install on www mcu for eonon Ga8161 7.1 a kld mcu file
They told me that www is 99.9% kld .. For now it works fine for me