How to proceed? The 4xl pixel went out, the vibration goes on pressing, but there is no picture. I read it on the Internet, as if the firmware has flown, but it also does not enter the recovery and fastboot. Is it possible to restore such a device?
plug it into a computer. open device manager. if it says qdloader 9008, you are in EDL mode and need to use a firehose file and firmware to flash it. if nothing happens when you plug it in, you probably just need to look up and install qualcomm qdloader drivers.
Hey!
You are on the EDL mode(Emergency download mode). I don't why you get there, but the only way to go out is to press power bottom + volume bottom(not sure if was vol+ or vol-)
If you can't them you may need to reflah the firmware...
Have a look on my profile, i tried to use this method to unlock a carrier-locked bootloader from a Pixel 4XL.
Good luck!
Related
Hello,
I was running CM13 and tried to install the most recently nightly (1121) I believe. Mi5 shutdown to reboot and install but never turned back on. The screen stays blank no matter what button combination I use. When i boot up holding Vol+ and power, it is visible as a drive and I can browse the file system from my computer.
I have tried various unbrick methods with no success.
I have tried to flash the Chinese Dev rom and Global using XiaoMiFlash but i get an error (can not found file flash_all.bat)
I have tried recovering with PC Suite - but i get various errors saying it can't connect.
Doesn't recognize when i reboot in recovery mode (Vol+ and Power)
Says to connect in normal mode first when i reboot it fastboot mode (Vol- and Power)
(also tried Chinese version, but I cant read the errors.
Fastboot devices shows it connected. Is there another way to unbrick? I have read a bit about EDL method but see other people saying it permabricked phone so I am nervous to try. Any idea?
OK so typing fastboot oem edl changes it - now shows up as RELINK HS-USB QDLoader 9008 (COM3) in device manager - but when i try to flash with XiaomiFlash I get a new error: cannot found programmer file. ugh.
Edit - also getting: cannot read from port COM3 (after first saying "read hello packet")
Apprently all versions of MiFlash arent the same - used the guide (and the version of MiFlash linked in this post) and it is booting now:
http://forum.xda-developers.com/mi-5/help/flash-rom-miflash-bricked-mi5-t3494738
This is the only unbrick method that worked for me
1A) Accidentally relocked the BL while on custom recovery and rom. Bricked, only turns on to blank black screen w/ solid blue LED.
1B) Able to go QFil Q9008 mode but all attempts result in errors, mostly Saharas. Unable to get into Fastboot
2A) Out of nowhere, days later. From OFF state, Vol+ and Vol- and plug I get the initial screen to scroll to select Reboot, Recovery, Fastboot, Reboot options.
2B) Was able to get into Fastboot and recognized by All-In-One Tool by Mauronofrio but I could not unlock the BL because I could not get a successful unlock file download.
2C) Also was able to get into EDL and what looked like my first successful download/flash in QFil 9008 mode. All previous attempts For the first time I saw progress bars and it was complete, okay/closed.
3A) Nothing happened for a long time so I unplugged and power cycle. Now its still bricked but in a different way. Button combos yield a quick vibration, green LED flicker once, back to all black screen, over and over.
3B) I am assuming I am in a worst brick than before? Now I am unable to get into Fastboot, EDL, computer doesn't even prompt driver issue when its off. Where now?
Hi,
I had the q9008 issue too after flashing the ZUI ROM with QFIL.
Phone turned off itself and then, nothing but a vibration after 15s on power button, and PC recognized it as Q9008 port. No screen, no LED.
I tried to plug it to PC after battery died, and had the red LED. Tried to charge it, and it went alive again. Now it's on AEX and everything is fine.
You can try that way, or follow this guide (I would do that if it would not be alive):
https://redirect.viglink.com/?forma...ww.zukfans.it/2016/07/06/gui...terminali-zuk/
Hi, same problem here.
Did you solve it? How?
Hi, Im kinda new to this bootloader thingy. What happen is, i updated the razer phone 2 to Pie, but notice wifi and sim card cant be detect. Even factory reset fails. So i thought of flashing new image on it. KINDA easy on my oneplus, but im not sure where I gone wrong on this razer phone 2, i accidentally unlock the bootloader. NOW the problem is HOW to relock it back? i been follow all youtube and guides all over the place but still fails.
The state of device atm, cannot be boot into Download Mode. Everytime I plug in usb c from Windows, it will boot into unlock bootloader warning page, and continue boot into the homescreen. testing the adbtools, fastboot also to no avail. Can anyone help and guide me how to relocking it back? Maybe i type wrongly on cmd or maybe other android steps not similar to razer one etc....:crying:help much appreciated.
Hold volume down while turning on. Then fastboot flashing lock.
the stock usb doesnt send things correctly in BL mode, https://www.amazon.com/Blackweb-3-Foot-Charge-Cable-Connector/dp/B07SG7P3KZ/ worked for me. with the correct usb cable you should be able to perform the lock commands correctly. can you give us more detail of what you tried on this phone so we know if we need to provide you additional information?
https://developer.razer.com/razer-phone-dev-tools/general-instructions/
"Locking the Bootloader
Locking the bootloader is recommended for security reasons. Some applications will not work with an unlocked bootloader.
Start the Phone in Download Mode with one of the following methods:
Using the adb tool: With the Phone powered on, execute: adb reboot bootloader Enter Download Mode:
Plug in a USB cable to connect your Razer Phone to your computer, Power Off the Phone, then turn it on and immediately press and hold the Volume Down button until “Download Mode” appears on screen.
Lock the critical partitions of the Bootloader first by running this command: fastboot flashing lock_critical
Your Razer Phone will show you a confirmation screen. Use the Volume Up/Volume Down buttons for navigation, and press the Power button to select. Your Phone will reboot."
I can't seem to enter download mode. All I have is fastboot mode and the option to either reboot, close the phone or enter recovery mode. I would really like to lock the bootloader, but I can't seem to be able to detect my phone on my PC even though I installed the fastboot driver.
The_Vinlander said:
I can't seem to enter download mode. All I have is fastboot mode and the option to either reboot, close the phone or enter recovery mode. I would really like to lock the bootloader, but I can't seem to be able to detect my phone on my PC even though I installed the fastboot driver.
Click to expand...
Click to collapse
You must use a USB 2.0 port. The RP2 isn't detected by fastboot when connected to a 3/3.1 port.
Reznor7 said:
You must use a USB 2.0 port. The RP2 isn't detected by fastboot when connected to a 3/3.1 port.
Click to expand...
Click to collapse
I tried this, but to no avail. I tried with 2 cables I had and it keeps telling me < waiting for device > when I enter this command; fastboot flashing lock_critical
The_Vinlander said:
I tried this, but to no avail. I tried with 2 cables I had and it keeps telling me < waiting for device > when I enter this command; fastboot flashing lock_critical
Click to expand...
Click to collapse
You need to go into your device manager and select [ android bootloader interface ] while in fastboot
Hi,
I'm stuck with my phone: it still loopbooting every 5seconds, black screen, only retrolight.
Bootloader is unlocked. I wanted to install twrp, but fastboot says partition recovery not existing.
After reboot, i'm stuck with this mod.
Try to press volume - to go again in fastboot : phone is detected by computer, then disconnected because it's rebooting.
Do you have a solution to try for me?
Or what are EDL point? I've tried to make an ELD cable but did not work either.
How long is your bootloader keeps active? If it's about 5 - 10 seconds, you can try paste the command to flash stock recovery. I attached it if it's possible to do so (from the latest global). And by the way - THERE IS STILL NO ANY CUSTOM RECOVERY for our device, sadly. Actually there is some, but only mouse works.
The commands to paste:
fastboot flash boot twrp.img
KastenTop said:
twrp.img
Click to expand...
Click to collapse
Boot.img in this case, doesn't make much difference
Sorry but my bootloader don't stay active long enough. I just ear usb detection from PC , then one seconde later, usb disconnection sound.
Phone is still loop booting.
Can you try then pasting "fastboot oem edl" (emergency download mode). The screen should turn black
After that flash with Xiaomi Flash tool
I'm unable to enter in FastBoot mode.
Phone booting black, and every 5 seconds , reboot.
If i push "volume down " button, i hear it vibrate, but nothing. Reboot and not detected by fastboot.exe
I think i have, with all manipulation , relocked the bootloader.
My only way, will to find a way to boot in EDL mode.
Test points, which are unknown so far. You have to disassemble the phone, tho. And you can try to find these points yourself, at your own risk obviously. If you will succeed, pls tell me. We need to know the test points.
I was exactly in same trouble, use This guide that solve the issue.
How to use MTK Bypass to backup or flash secure boot MTK
This is a step by step guide showing how to flash or backup a Mediatek (MTK) secure boot device without using a custom download agent (DA). This tool disables the SLA / DAA bootrom protection A little
forum.hovatek.com
Press mobile three buttons and connect cable to pc to enter brom mode. Because mtk models don't have test point. So don't need to open mobile.
proxynet said:
I'm unable to enter in FastBoot mode.
Phone booting black, and every 5 seconds , reboot.
If i push "volume down " button, i hear it vibrate, but nothing. Reboot and not detected by fastboot.exe
I think i have, with all manipulation , relocked the bootloader.
My only way, will to find a way to boot in EDL mode.
Click to expand...
Click to collapse
EDL mode in Xiaomi mediatek are called BROM mode. Don't need to disarm the mobile.
Thanks !
I tried, it works like a charm !
You're the best man
Zaiserr2 said:
EDL mode in Xiaomi mediatek are called BROM mode. Don't need to disarm the mobile.
Click to expand...
Click to collapse
nice tip!!!! this is a very helpfull guide for solve hard brick on mtk devices. i have decided never modding this phone, excep root when i need a full backup with migrate. because is much mure complicated than snapdragons. but your post is very very helpfull for who want to try anyway
Hi i just oficialy unlocked bootloader, flashed twrp recovery boot and restarted phone. After that restart, phone got stuck in loop rebooting to MI logo. Recovery and Fastboot not loading when i press right buttons. Phone just vibrate and keep restarting. I had to dry off battery to turn it off becouse when i connect phone to cable it auto turn on and start restarting. I tryed also unplug battery and flash it by other rom but connection with pc is broken when phone still restarting every 5s. Is there any chance to save this phone from scrap? Thank you
Durien Daragoth said:
Hi i just oficialy unlocked bootloader, flashed twrp recovery boot and restarted phone. After that restart, phone got stuck in loop rebooting to MI logo. Recovery and Fastboot not loading when i press right buttons. Phone just vibrate and keep restarting. I had to dry off battery to turn it off becouse when i connect phone to cable it auto turn on and start restarting. I tryed also unplug battery and flash it by other rom but connection with pc is broken when phone still restarting every 5s. Is there any chance to save this phone from scrap? Thank you
Click to expand...
Click to collapse
You might want to take a look at this.
[GUIDE]How to reboot to EDL from fastboot
Most Qualcomm-based Android PDAs support emergency download (EDL) mode allowing to unbrick device, unlock bootloader or modify protected device parameters. If ADB interface is accessible, "adb reboot edl" can be used to reboot to EDL mode. Many...
forum.xda-developers.com
Obi_Wlan said:
You might want to take a look at this.
[GUIDE]How to reboot to EDL from fastboot
Most Qualcomm-based Android PDAs support emergency download (EDL) mode allowing to unbrick device, unlock bootloader or modify protected device parameters. If ADB interface is accessible, "adb reboot edl" can be used to reboot to EDL mode. Many...
forum.xda-developers.com
Click to expand...
Click to collapse
Thank but phone simply dont booting to fastboot mode.
Durien Daragoth said:
Thank but phone simply dont booting to fastboot mode.
Click to expand...
Click to collapse
You have to experiment with some button combinations. I ran into the same problem with a different phone two years ago. Read everything about this even if fastboot isn't working right now.
[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo]
[GUIDE][TOOL] Reboot to EDL mode from FASTBOOT! No More "Test Point Method"! [kenzo] Reboot to EDL mode from FASTBOOT! No more Test Point Method needed ;) Technical Details: Redmi Note 3 support rebooting to EDL in Android Bootloader aboot...
forum.xda-developers.com
Service centre will be your best bet
Durien Daragoth said:
Hi i just oficialy unlocked bootloader, flashed twrp recovery boot and restarted phone. After that restart, phone got stuck in loop rebooting to MI logo. Recovery and Fastboot not loading when i press right buttons. Phone just vibrate and keep restarting. I had to dry off battery to turn it off becouse when i connect phone to cable it auto turn on and start restarting. I tryed also unplug battery and flash it by other rom but connection with pc is broken when phone still restarting every 5s. Is there any chance to save this phone from scrap? Thank you
Click to expand...
Click to collapse
first let's go, download the fastboot stock version of the ROM then download Miflash, unzip the rom on your main disk twice, now on your cell phone you will press the power off button and at the same time the fastboot button (you must have messed up the file boot so it doesn't turn on) and play Miflash also on C disk, open Miflash on mobile in fastboot mode and select ROM folder don't forget to put the option to just clean and not lock, when the process is finished you wait for the phone to turn on
Player__y said:
first let's go, download the fastboot stock version of the ROM then download Miflash, unzip the rom on your main disk twice, now on your cell phone you will press the power off button and at the same time the fastboot button (you must have messed up the file boot so it doesn't turn on) and play Miflash also on C disk, open Miflash on mobile in fastboot mode and select ROM folder don't forget to put the option to just clean and not lock, when the process is finished you wait for the phone to turn on
Click to expand...
Click to collapse
If you have any, let me know on discord, 𝑃𝑙𝑎𝑦𝑒𝑟#2028
Thx but phone dont booting to fastboot mode so i cant flash boot.img i tryed now SP Flash too in linux and still same errors becouse phone disconecting too fast. I think technician service will be solution..
Dont use The daanm Sp flash Tool , Its for mediatek devices, USE Miflash, and Its impossible a phone dont boot in fastboot mode, try again, pls hold The button
I have both Mi flash and SP flash tool
Without fastboot you cant do much...
in Miflash it dont do anything even device it dont see on COM3
in SP flash too it react but with errors becouse of disconecting
phone dont boot right becouse both A and B boot images are corrupted.
Does your screen at boot turn red? I've done everything on my cell phone, several things have happened to me and not once did fastboot have a problem, because fastboot is a totally different place to boot, there is only this possibility if you used commands in adb to remove or do something in fastboot that made it useless, it's impossible to happen this in the way you said
yes i did adb commands in fastboot becouse i instaled recovery and this all happend after reboot
no problem doing things in adb, I said in the sense that you deleted fastboot in adb but that didn't happen by the way you said
Turn off your phone.
Press and hold the Power + Volume Down buttons together and immediately connect the device to the PC. You need to time it perfectly.
It will automatically boot into EDL mode, and LED lights may blink.
Download QPST Flash Tool and install your device's firmware using QFIL(comes included in QPST).
I suggest you to read everything about it online.
Obi_Wlan said:
Turn off your phone.
Press and hold the Power + Volume Down buttons together and immediately connect the device to the PC. You need to time it perfectly.
It will automatically boot into EDL mode, and LED lights may blink.
Download QPST Flash Tool and install your device's firmware using QFIL(comes included in QPST).
I suggest you to read everything about it online.
Click to expand...
Click to collapse
I tryed but not succes. It just booting every 5s nowhere. Cant get to EDL mode sorry. And correct turn off phone isnt possible i have to unplug battery flex cable but i also tryed. Only possible state where it dont restarting is when battery is unpluged and i connect phone on cable with pc and pressing volume down+power. But connection to COM3 is only 2s.
Well, in that case you need to short the test points on your motherboard and plug the phone into your PC at the same time.
Watch several videos related to it on YouTube first.
Wait, is your phone Redmi Note 11 or 11s?
I will try the point test. I have Redmin Note 11s.
Ahhhh...you posted it on Note 11 forum.
Can't help you mate. Things are more complicated in mediatek devices.
Still, this thread might help a little. Good luck.
(Guide) How to fix a hard bricked Redmi Note 9 (Merlin) (Hard Brick)
A how-to guide of restoring a completely bricked Redmi Note 9 Hi, In this guide, I will teach you how to fix a hard-bricked Redmi Note 9 (merlin) and bring it back to its original state. How does a hard-bricked Redmi Note 9 look like? it's stuck...
forum.xda-developers.com
Now i have bit progress with python im able to hold COM3 port connection around 60s. But when i start SP Flash Tool it will always make error. STATUS_BROM_CMD_STARTCMD_FAIL (0xC0060001) and STATUS_ERR (0xC0010001) , STATUS_BROM_CMD_FAIL
I finally managed to connect device for longer time cca 1 min with MTKMETAUtilityV49 and it helped me also disable auhorized connection for SP Flash tool V5. By this i formated whole disc except bootloader. Now phone dont self restarting so it is prepared for instal fresh rom. I think this will be again problem becouse i geting this error after few seconds of flashing: STATUS_SEC_IMG_TOO_LARGE