Hi!
I'm currently trying to install TWRP on my Samsung Galaxy S5 Active (kminilte) and every time I flash on Odin3, it says "PASS!" but when I do the recovery combo, it spits me into the normal recovery menu. I have also not rooted my phone yet.
Here's the logs from Odin3:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1401)..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Here's the TAR IMG I'm using if it's of any use:
untick the auto reboot checkbox. flash tar in AP slot
Tried that, didn't work. Is there another like recovery code I need to use? Currently using HOME + PWR + VOL DWN to access Download Mode
When I press HOME + PWR + VOL UP it gives me a menu with it saying like "Not connected!" and then it goes to a menu. Should I do something from there?
jazztoasty101 said:
Hi!
I'm currently trying to install TWRP on my Samsung Galaxy S5 Active (kminilte) and every time I flash on Odin3, it says "PASS!" but when I do the recovery combo, it spits me into the normal recovery menu. I have also not rooted my phone yet.
Here's the logs from Odin3:
<ID:0/005> Added!!
<ID:0/005> Odin engine v(ID:3.1401)..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> RQT_CLOSE !!
<ID:0/005> RES OK !!
<ID:0/005> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Here's the TAR IMG I'm using if it's of any use:
Click to expand...
Click to collapse
Uncheck auto reboot and after flash force reboot too twrp. If you let phone just reboot normally it will replace twrp back with stock. Once you reboot straight too twrp it will patch the system so it wont replace twrp with stock recovery
jrkruse said:
Uncheck auto reboot and after flash force reboot too twrp. If you let phone just reboot normally it will replace twrp back with stock. Once you reboot straight too twrp it will patch the system so it wont replace twrp with stock recovery
Click to expand...
Click to collapse
How do I force reboot?
jazztoasty101 said:
How do I force reboot?
Click to expand...
Click to collapse
hold the power plus volume down for a few seconds phone will power off immediately at this points hold buttons to reboot to recovery. Home + pwr + vol up
Related
My galaxy was flashed with the latest beta of Android 2.2 then I applied the root, since then my download mode stopped working and my galaxy get frozen after I turn it ON at the Galaxy S black and white screen... The only two mode that I was able to bring up is FORCED UPLOAD by KEY PRESSING and UNKNOWN MODE...
This is what I did to get the download mode and I double checked it twice that his method works before I posted here:
btw: my OS is Windows 7 and I installed the Windows 7 drivers the filename is "Windows 7&Vista x64 USB Driver.zip"
file required are the firmware that I don't have I used again Android 2.2 I don't know what firmware to put I would like to know what firmware was on the original Bell i9000M if someone can tell me it's appreciated.
The other required file is Odin3 v1.30
I did the following first I right clicked the Odin3 and UNBLOCK it and change the compatible mod to XP
Here are the STEPS:
1- disconnect the cable from the phone.
2- launch Odin3 v1.30
3- Put your phone into FORCED UPLOAD by KEY PRESSING
4- Connect the USB cable to your phone (Odin3 should display "Added!!"
5- Select your file PIT, PDA, PHONE and CSC then click on START
6- Your Odin will stop on "SetupConnection.." (if you use the older version of Odin it will stop at "File analysis.." and I don`t know if it works with the older version.
7. Now when you see the "SetupConnection.." Press Volume down + Home + Power and KEEP HOLDING IT UNTIL YOU SEE the DOWNLOAD MODE
This is the LOG of my Odin
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Removed!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> factoryfs.rfs
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> zImage
<ID:0/005> modem.bin
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/006> Added!!
<ID:0/006> Removed!!
If you have noticed after you see "SetupConnection.." your phone will be disconnected from Odin3 then it will reconnect then BINGO you will get the download mode.
I hope this will help all ppl who are stuck at the boot screen without having access to the download mode.
Now I need a favor I dont know when to get the original firmware of bell I wanna bring back my phone to the original state.
Thanks
DeCoDish
Update: I've installed Kies the latest version I thought I can get the original firmware using Kies so I decided to bring the download mode using the above procedure then I was surprised the I could not get to the download mode again!!! Hmmm.... I uninstalled Kies then I tried again with no luck... I re-installed the driver "Windows 7&Vista x64 USB Driver.zip" then I repeated the above steps then the download mode is back.... Weird isn't??? It looks like the Kies override the driver with another driver... So in order to get my procedure working make sure you UNINSTALL completely KIES from your system and install the drivers that I mentioned... Also notice that adb.exe detects my device and it wasn't before... Now I have the Downloading mode but I don't know what to load Hope that anyone can point me where I can download the original firmware that comes with Bell i9000M model...
DeCoDish
OUTCH!!!! What is that file s1_odin_20100512.pit ???????
I loaded only this file using repartition option without selecting the PDA, MODEM and CSC the I flashed the pit file the phone rebooted then BLACK SCREEN OF DEATH the PHONE DOES NOT TURN ON!!!! Anyone knows why??
DeCoDish
I have the same problem flashed to jp3 my i9000m loosed its recovery and download mode. Work hard to get it now easily lost
Hi DeCoDish,
Thanks - you revived my device from bricked state.
You can find almost all official firmware version on www samfirmware com (sorry not allowed to post full url as I am a new user and still waits to be verified by moderator).
/Anders
How long should keep pressing that combo for download mode, cuz when I'm keep pressing it it just shows recharge screen and i realy need download mode.
DeCoDish said:
OUTCH!!!! What is that file s1_odin_20100512.pit ???????
I loaded only this file using repartition option without selecting the PDA, MODEM and CSC the I flashed the pit file the phone rebooted then BLACK SCREEN OF DEATH the PHONE DOES NOT TURN ON!!!! Anyone knows why??
DeCoDish
Click to expand...
Click to collapse
So you just randomly flashed a file to your phone, not even knowing what it is or does?
Just for the fun of it?
And you're wondering why your phone is now fked?
Do a full reflash with PIT, CSC, MODEM and PDA.
FFS...
DeCoDish said:
My galaxy was flashed with the latest beta of Android 2.2 then I applied the root, since then my download mode stopped working and my galaxy get frozen after I turn it ON at the Galaxy S black and white screen... The only two mode that I was able to bring up is FORCED UPLOAD by KEY PRESSING and UNKNOWN MODE...
This is what I did to get the download mode and I double checked it twice that his method works before I posted here:
btw: my OS is Windows 7 and I installed the Windows 7 drivers the filename is "Windows 7&Vista x64 USB Driver.zip"
file required are the firmware that I don't have I used again Android 2.2 I don't know what firmware to put I would like to know what firmware was on the original Bell i9000M if someone can tell me it's appreciated.
The other required file is Odin3 v1.30
I did the following first I right clicked the Odin3 and UNBLOCK it and change the compatible mod to XP
Here are the STEPS:
1- disconnect the cable from the phone.
2- launch Odin3 v1.30
3- Put your phone into FORCED UPLOAD by KEY PRESSING
4- Connect the USB cable to your phone (Odin3 should display "Added!!"
5- Select your file PIT, PDA, PHONE and CSC then click on START
6- Your Odin will stop on "SetupConnection.." (if you use the older version of Odin it will stop at "File analysis.." and I don`t know if it works with the older version.
7. Now when you see the "SetupConnection.." Press Volume down + Home + Power and KEEP HOLDING IT UNTIL YOU SEE the DOWNLOAD MODE
This is the LOG of my Odin
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Removed!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> factoryfs.rfs
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> zImage
<ID:0/005> modem.bin
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/006> Added!!
<ID:0/006> Removed!!
If you have noticed after you see "SetupConnection.." your phone will be disconnected from Odin3 then it will reconnect then BINGO you will get the download mode.
I hope this will help all ppl who are stuck at the boot screen without having access to the download mode.
Now I need a favor I dont know when to get the original firmware of bell I wanna bring back my phone to the original state.
Thanks
DeCoDish
Update: I've installed Kies the latest version I thought I can get the original firmware using Kies so I decided to bring the download mode using the above procedure then I was surprised the I could not get to the download mode again!!! Hmmm.... I uninstalled Kies then I tried again with no luck... I re-installed the driver "Windows 7&Vista x64 USB Driver.zip" then I repeated the above steps then the download mode is back.... Weird isn't??? It looks like the Kies override the driver with another driver... So in order to get my procedure working make sure you UNINSTALL completely KIES from your system and install the drivers that I mentioned... Also notice that adb.exe detects my device and it wasn't before... Now I have the Downloading mode but I don't know what to load Hope that anyone can point me where I can download the original firmware that comes with Bell i9000M model...
DeCoDish
Click to expand...
Click to collapse
I did everything step by step...
but now my phone doesn't even starts, it's like it died litterally...
any ideas...???
ANYONE...?????
xero2002 said:
So you just randomly flashed a file to your phone, not even knowing what it is or does?
Just for the fun of it?
And you're wondering why your phone is now fked?
Do a full reflash with PIT, CSC, MODEM and PDA.
FFS...
Click to expand...
Click to collapse
how do we do this since the phone does not even starts...
not even with the key combination...
SOLVED
You need to hold the power, vol down and home key down and then put the battery in.
"5- Select your file PIT, PDA, PHONE and CSC then click on START"
Where can i get these files? I got my phone into this state through some ****ty app, i dont need to be told how dumb i am, if you can help this is greatly appreciated.
Can anyone please share the file Windows 7&Vista x64 USB Driver.zip ?
Thanks
Hi Guys,
Don't know what happened, and now I am unable to do
Data data factory reset through CWM
Unable to install rom through Odin
Unable to install rom through CWM
Unable to restore my Backup (its giving error while restoring data)
Anybody please help me...
hakimkkb4u said:
Hi Guys,
Don't know what happened, and now I am unable to do
Data data factory reset through CWM
Unable to install rom through Odin
Unable to install rom through CWM
Unable to restore my Backup (its giving error while restoring data)
Anybody please help me...
Click to expand...
Click to collapse
Please share how you tried flashing ROM using Odin.. because if none of the above doesn't work , as least PC Odin flash should work for sure..
I tried via odin but it stuck on
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> factoryfs.img
<ID:0/005> NAND Write Start!!
hakimkkb4u said:
I tried via odin but it stuck on
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> factoryfs.img
<ID:0/005> NAND Write Start!!
Click to expand...
Click to collapse
Are you attaching PIT file?? If not try different version of Odin.. or a different ROM. it should work.
ranjan.alva said:
Are you attaching PIT file?? If not try different version of Odin.. or a different ROM. it should work.
Click to expand...
Click to collapse
the same here, only download, odin stuck on nand write.
Ok let me try....
OK let me try any other stock Rom...
I tried different rom, different version of odin but same result...
again stuck on...
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> factoryfs.img
<ID:0/005> NAND Write Start!!
install the attached file with odin....
extract the file first you should get a tar file;....
flash it with odin in the PDA...
after completion...
remove battery for 30 seconds put battery in
hold home + vol up.... boot in recovery then try factory reset...
Thanks for your help....
I tried but having same problem...
able to enter in CWM but unable to do data factory reset...
while entering in CWM I am Getting this error
E:can't mount/cache/recovery/command
E:can't mount/cache/recovery/log
E:can't open/cache/recovery/log
E:can't mount/cache/recovery/last_log
E:can't open/cache/recovery/last_log
Ok Seems like you messed up your partition...
I attached new files
use the correct one based on your phone factory memory...
most likely its the 16GB but I include both just incase
Boot In Download Mode
Open Odin and load file in PIT
reboot...
Book Back in Download and load previous file I supplied
Reboot.....
the boot in recovery then Factory Reset......
antiguangenius said:
Ok Seems like you messed up your partition...
I attached new files
use the correct one based on your phone factory memory...
most likely its the 16GB but I include both just incase
Boot In Download Mode
Open Odin and load file in PIT
reboot...
Book Back in Download and load previous file I supplied
Reboot.....
the boot in recovery then Factory Reset......
Click to expand...
Click to collapse
Tnx for this. I was able to boot into recovery and did a Factory Reset. Weird, it took so long to format data.
I am now trying to flash my ROM. Hope it will work.
Cheers!
armic said:
Tnx for this. I was able to boot into recovery and did a Factory Reset. Weird, it took so long to format data.
I am now trying to flash my ROM. Hope it will work.
Cheers!
Click to expand...
Click to collapse
good luck buddy..... I'm glad you got further.......
antiguangenius said:
good luck buddy..... I'm glad you got further.......
Click to expand...
Click to collapse
Got /System error when trying to restore my NAND BACKUP...
Tried to Flash ROM from ZIP. Finished but took so long.
Rebooted and got stuck in SAMSUNG GALAXY Note logo...
Any suggestions?
antiguangenius said:
install the attached file with odin....
extract the file first you should get a tar file;....
flash it with odin in the PDA...
after completion...
remove battery for 30 seconds put battery in
hold home + vol up.... boot in recovery then try factory reset...
Click to expand...
Click to collapse
Are you aware, you are advising will raise flash counter?
armic said:
Got /System error when trying to restore my NAND BACKUP...
Tried to Flash ROM from ZIP. Finished but took so long.
Rebooted and got stuck in SAMSUNG GALAXY Note logo...
Any suggestions?
Click to expand...
Click to collapse
are you sure you're the correct rom??
whats the exact model of your device???
---------- Post added at 03:27 AM ---------- Previous post was at 03:25 AM ----------
dr.ketan said:
Are you aware, you are advising will raise flash counter?
Click to expand...
Click to collapse
yes I do but am sure he already raised it before.... the chap is stuck, i'm guessing anything that works he will be happy with... he did have a custom rom before.... so that flag has been up long time...
mine seems to be stuck at set partition was i rigght in leaving re partition in odin to on
unbale to do restore factory setting after root my cell
hi frnds plz help me..yesterday i rooted my phone mmx a70..i flashed cwm recovery..bt when i tried to make back up of existing rom my cell jst boot n stuck at logo..i removed battry turnd my phone on its working..then i tried to restore factory setting bt same thing happend phone stuck at logo ntnhg happens.help me guyzz..i m also not able to go to the boot screen....
Flash Abyss kernel and try it.. should be ok..
Just download abyss kernel and flash it via cwm and then use redpill recovery to do all your stuff.. it worked for me.. even data can be restored pretty easily.. or even backed up...
sudhanshu124 said:
hi frnds plz help me..yesterday i rooted my phone mmx a70..i flashed cwm recovery..bt when i tried to make back up of existing rom my cell jst boot n stuck at logo..i removed battry turnd my phone on its working..then i tried to restore factory setting bt same thing happend phone stuck at logo ntnhg happens.help me guyzz..i m also not able to go to the boot screen....
Click to expand...
Click to collapse
antiguangenius said:
Ok Seems like you messed up your partition...
I attached new files
use the correct one based on your phone factory memory...
most likely its the 16GB but I include both just incase
Boot In Download Mode
Open Odin and load file in PIT
reboot...
Book Back in Download and load previous file I supplied
Reboot.....
the boot in recovery then Factory Reset......
Click to expand...
Click to collapse
Bro....
Can you help me on this?
I download your file and put in PIT and start...
<ID:0/009> Added!!
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Set PIT file..
<ID:0/009> DO NOT TURN OFF TARGET!!
it stuck here.
any suggestion?
I think I have same problem o S4 L720
antiguangenius said:
Ok Seems like you messed up your partition...
I attached new files
use the correct one based on your phone factory memory...
most likely its the 16GB but I include both just incase
Boot In Download Mode
Open Odin and load file in PIT
reboot...
Book Back in Download and load previous file I supplied
Reboot.....
the boot in recovery then Factory Reset......
Click to expand...
Click to collapse
Hi xda, I have A sprint S4 flashed to Boost Mobile . I rooted (twrp) it using odin ,and I was trying to get the free Hot Spot . I was told to download two files to my sd card and rename them in the system file and them to copy and paste them in from my sd to the system file . When I tried to do that ( I did multi select ) only one file pasted but it didn't past in systems not sure where it went . I checked the sd and one was missing so I powered it off and replaced the one that was missing . When I started my phone up it froze on the yellow Sprint screen , I did some research and im not sure what I tried in odin but when it rebooted it's now stuck on the Samsung Galaxy Screen ! I tried odin to go back stock and I tried the unbrick methods and it keep failing . I've tried all the trouble shooting methods I could find .I tried factory reset , wipes and nothing worked for me .I also stop all Kies services from task manager, And when odin fails it says :
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> L720TVPUAMK5_L720TSPTAMK5_L720TVPUAMK5_HOME.tar.md 5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> sbl2.mbn
<ID:0/006> NAND Write Start!!
<ID:0/006>
<ID:0/006> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I think I need a pit file for S4 L720 Thanks!!
Galaxy SIII I9305 shows up with not booting, getting stuck at the SIII logo.
Does the same when trying to get into recovery, so I tried to flash it with Odin.
Flash screen says:
Odin Mode
Product Name: GT-I9305
Custom Binary Download: No
Current Binary: Samsung Official
System Status: Official
Knox Warranty Void: 0
RP SWREV: A2
Click to expand...
Click to collapse
I tried to flash it with the latest packages from Sammobile, but no matter what I try, Odin always fails right away when flashing boot.img... any idea what the problem might be, or what I'm doing wrong?
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9305XXUENE4_I9305H3GENE1_I9305NEUEML2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/003> Removed!!
Click to expand...
Click to collapse
Centrumgsm said:
Galaxy SIII I9305 shows up with not booting, getting stuck at the SIII logo.
Does the same when trying to get into recovery, so I tried to flash it with Odin.
Flash screen says:
I tried to flash it with the latest packages from Sammobile, but no matter what I try, Odin always fails right away when flashing boot.img... any idea what the problem might be, or what I'm doing wrong?
Click to expand...
Click to collapse
stupid question, but did you go in to download mode when flashing? thats by pressing menu button + volume down button + power button. then press volume up to agree with download mode and then flash with odin. And make sure you have all drivers installed
klemen241 said:
stupid question, but did you go in to download mode when flashing? thats by pressing menu button + volume down button + power button. then press volume up to agree with download mode and then flash with odin. And make sure you have all drivers installed
Click to expand...
Click to collapse
I did. As far as I can tell, I did everything according to the guides.
[edit] I also managed to flash a different I9305 without problem, so I'm sure it's not driver or flash file related. There is something with this specific phone that prevents flashing.
I've seen a "rescue firmware" for the I9300 with separate PDA, MODEM and CSC (+.pit) files for when the regular stock firmware wouldn't flash, and I was wondering if such a thing exists for the I9305 or if there is a guide on how I could make one.
Try to get a PIT file for the i9305 and add it to ODIN. If you don't do this, ODIN extracts the PIT from the device, and that might be corrupted.
daedric said:
Try to get a PIT file for the i9305 and add it to ODIN. If you don't do this, ODIN extracts the PIT from the device, and that might be corrupted.
Click to expand...
Click to collapse
Can't brick the device much more than it already is, right? I tried it, but it just gets stuck here:
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
Click to expand...
Click to collapse
I got bored after 15 minutes, turned off the target, turned on the target, no change, still the same error when flashing.
Thought about the Knox bootloader preventing me from updating it, but that usually gives me some kind of error message right on the flash screen. Plus I'm using the latest images, and the other I9305 also says "SWREV A2", so that shouldn't be a problem.
This looks more and more like a motherboard replacement...
All i have to say is, good luck. Things don't look good.
Try to flash just a recovery via ODIN. You'll kiss knox goodbye, but we're out of options.
https://goo.im/devs/philz_touch/CWM_Advanced_Edition/i9305/
daedric said:
Try to flash just a recovery via ODIN. You'll kiss knox goodbye, but we're out of options.
Click to expand...
Click to collapse
Tried it, no go. Same error, still won't boot into recovery. On the upside, it didn't trip Knox either
Ok, just for good measure, let's get down to the basics.
Questions:
1. What type of USB cable are you using? Can you try another?
2. Is the USB cable connected directly to the computer , or via HUB / Front ports ?
3. Have you tried cleaning the usb port on the device ?
I've covered all the basics, even tried another computer. Same results.
I couldn't find a solution, ended up sending the phone for a motherboard replacement. Thanks for the suggestions, everyone!
i really need help guys , i'm still getting the stock recovery even after flashing TWRP !!!
odin log:"
<ID:0/007> Odin engine v(ID:3.1100)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> recovery.img
<ID:0/007> NAND Write Start!!
<ID:0/007> RQT_CLOSE !!
<ID:0/007> RES OK !!
<ID:0/007> Removed!!
<ID:0/007> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
as you can see the log says that nothing wrong happened and everything went 100% successful but still don't understand why is this happening !!! :crying: :crying:
please help me because i cant leave the phone without of flashing deep sleep fix
When you flash via ODIN uncheck auto restart. Manually restart your device after you get the PASS.
i'l try that
still getting the stock one :/
Try this:
When Odin opens uncheck the auto reboot option to stop your device rebooting back to Android after flashing the custom recovery completes.
After the flash completes recheck the auto reboot option and close Odin.
Unplug the USB cable then hold the volume up, home and power buttons together for about 10 seconds until you see the Samsung logo. Release the buttons right away to boot straight to custom recovery.
thank youuuuuuu sooooooooooooo mcuhhhhhhhhhh it really worked , u really saved me , i've almost lost my hope
took me about 7 straight hours to find the fix thank you sooo much Bro !
No problem. Glad I could help
Dear All,
It's my first time converting from iPhones to Android. Happy to join this community to learn and share.
It was my first amateur experience flashing my Galaxy Note 9.
Basically, I flashed an incorrect BL file at Odin after OEM Unlock. Phone was running Android 9 and it was a N960N (Korean Model).
I downloaded the BL file from another forum that was apparently supposedly to be only flashed inside TWRP.
I was stupid enough to change that zip file into a .tar file.
After a successful flash at BL, the phone seems to be bricked. It is unable to go into recovery or download mode.
I've tried
1. (vol down + bixby + power)
2. (vol up + bixby + power)
3. (vol down + bixby)
Whenever I do this, the following message just keeps getting prompted "KERNEL REV. CHECK FAIL DEVICE:3 BINARY: 2 (BOOT)
The computer can't detect the phone anymore....
I was stupid. Please advise me. Could it be that on the hardware volume down button is faulty? I was having a hard time bringing it to download mode at the beginning. I used recovery mode to boot into download mode and then made this big mistake.
I brought it to a repair shop, they said the volume down button is working so its more likely software problem.......
Any solution?
Thank you in advance.
This is the Odin Log
<ID:0/009> Added!!
<ID:0/009> Odin engine v(ID:3.1301)..
<ID:0/009> File analysis..
<ID:0/009> Total Binary size: 8 M
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> NAND Write Start!!
<ID:0/009> SingleDownload.
<ID:0/009> cm.bin
<ID:0/009> keystorage.bin
<ID:0/009> sboot.bin
<ID:0/009> up_param.bin
<ID:0/009> RQT_CLOSE !!
<ID:0/009> RES OK !!
<ID:0/009> Removed!!
<ID:0/009> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
Seems like that the OS installed correctly on your device. What is the issue you are having?
For download mode , try vol down + Bixby and insert usb.
https://www.sammobile.com/samsung/galaxy-note9/firmware/#SM-N960N
chick this site to download the room compatible with your phone
for download mode
1. (vol down + bixby + power) and Connect the mobile phone to the charging cable at the same time