My galaxy was flashed with the latest beta of Android 2.2 then I applied the root, since then my download mode stopped working and my galaxy get frozen after I turn it ON at the Galaxy S black and white screen... The only two mode that I was able to bring up is FORCED UPLOAD by KEY PRESSING and UNKNOWN MODE...
This is what I did to get the download mode and I double checked it twice that his method works before I posted here:
btw: my OS is Windows 7 and I installed the Windows 7 drivers the filename is "Windows 7&Vista x64 USB Driver.zip"
file required are the firmware that I don't have I used again Android 2.2 I don't know what firmware to put I would like to know what firmware was on the original Bell i9000M if someone can tell me it's appreciated.
The other required file is Odin3 v1.30
I did the following first I right clicked the Odin3 and UNBLOCK it and change the compatible mod to XP
Here are the STEPS:
1- disconnect the cable from the phone.
2- launch Odin3 v1.30
3- Put your phone into FORCED UPLOAD by KEY PRESSING
4- Connect the USB cable to your phone (Odin3 should display "Added!!"
5- Select your file PIT, PDA, PHONE and CSC then click on START
6- Your Odin will stop on "SetupConnection.." (if you use the older version of Odin it will stop at "File analysis.." and I don`t know if it works with the older version.
7. Now when you see the "SetupConnection.." Press Volume down + Home + Power and KEEP HOLDING IT UNTIL YOU SEE the DOWNLOAD MODE
This is the LOG of my Odin
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Removed!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> factoryfs.rfs
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> zImage
<ID:0/005> modem.bin
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/006> Added!!
<ID:0/006> Removed!!
If you have noticed after you see "SetupConnection.." your phone will be disconnected from Odin3 then it will reconnect then BINGO you will get the download mode.
I hope this will help all ppl who are stuck at the boot screen without having access to the download mode.
Now I need a favor I dont know when to get the original firmware of bell I wanna bring back my phone to the original state.
Thanks
DeCoDish
Update: I've installed Kies the latest version I thought I can get the original firmware using Kies so I decided to bring the download mode using the above procedure then I was surprised the I could not get to the download mode again!!! Hmmm.... I uninstalled Kies then I tried again with no luck... I re-installed the driver "Windows 7&Vista x64 USB Driver.zip" then I repeated the above steps then the download mode is back.... Weird isn't??? It looks like the Kies override the driver with another driver... So in order to get my procedure working make sure you UNINSTALL completely KIES from your system and install the drivers that I mentioned... Also notice that adb.exe detects my device and it wasn't before... Now I have the Downloading mode but I don't know what to load Hope that anyone can point me where I can download the original firmware that comes with Bell i9000M model...
DeCoDish
OUTCH!!!! What is that file s1_odin_20100512.pit ???????
I loaded only this file using repartition option without selecting the PDA, MODEM and CSC the I flashed the pit file the phone rebooted then BLACK SCREEN OF DEATH the PHONE DOES NOT TURN ON!!!! Anyone knows why??
DeCoDish
I have the same problem flashed to jp3 my i9000m loosed its recovery and download mode. Work hard to get it now easily lost
Hi DeCoDish,
Thanks - you revived my device from bricked state.
You can find almost all official firmware version on www samfirmware com (sorry not allowed to post full url as I am a new user and still waits to be verified by moderator).
/Anders
How long should keep pressing that combo for download mode, cuz when I'm keep pressing it it just shows recharge screen and i realy need download mode.
DeCoDish said:
OUTCH!!!! What is that file s1_odin_20100512.pit ???????
I loaded only this file using repartition option without selecting the PDA, MODEM and CSC the I flashed the pit file the phone rebooted then BLACK SCREEN OF DEATH the PHONE DOES NOT TURN ON!!!! Anyone knows why??
DeCoDish
Click to expand...
Click to collapse
So you just randomly flashed a file to your phone, not even knowing what it is or does?
Just for the fun of it?
And you're wondering why your phone is now fked?
Do a full reflash with PIT, CSC, MODEM and PDA.
FFS...
DeCoDish said:
My galaxy was flashed with the latest beta of Android 2.2 then I applied the root, since then my download mode stopped working and my galaxy get frozen after I turn it ON at the Galaxy S black and white screen... The only two mode that I was able to bring up is FORCED UPLOAD by KEY PRESSING and UNKNOWN MODE...
This is what I did to get the download mode and I double checked it twice that his method works before I posted here:
btw: my OS is Windows 7 and I installed the Windows 7 drivers the filename is "Windows 7&Vista x64 USB Driver.zip"
file required are the firmware that I don't have I used again Android 2.2 I don't know what firmware to put I would like to know what firmware was on the original Bell i9000M if someone can tell me it's appreciated.
The other required file is Odin3 v1.30
I did the following first I right clicked the Odin3 and UNBLOCK it and change the compatible mod to XP
Here are the STEPS:
1- disconnect the cable from the phone.
2- launch Odin3 v1.30
3- Put your phone into FORCED UPLOAD by KEY PRESSING
4- Connect the USB cable to your phone (Odin3 should display "Added!!"
5- Select your file PIT, PDA, PHONE and CSC then click on START
6- Your Odin will stop on "SetupConnection.." (if you use the older version of Odin it will stop at "File analysis.." and I don`t know if it works with the older version.
7. Now when you see the "SetupConnection.." Press Volume down + Home + Power and KEEP HOLDING IT UNTIL YOU SEE the DOWNLOAD MODE
This is the LOG of my Odin
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Removed!!
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> boot.bin
<ID:0/005> Sbl.bin
<ID:0/005> param.lfs
<ID:0/005> factoryfs.rfs
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> zImage
<ID:0/005> modem.bin
<ID:0/005> cache.rfs
<ID:0/005> dbdata.rfs
<ID:0/005> Removed!!
<ID:0/005> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/006> Added!!
<ID:0/006> Removed!!
If you have noticed after you see "SetupConnection.." your phone will be disconnected from Odin3 then it will reconnect then BINGO you will get the download mode.
I hope this will help all ppl who are stuck at the boot screen without having access to the download mode.
Now I need a favor I dont know when to get the original firmware of bell I wanna bring back my phone to the original state.
Thanks
DeCoDish
Update: I've installed Kies the latest version I thought I can get the original firmware using Kies so I decided to bring the download mode using the above procedure then I was surprised the I could not get to the download mode again!!! Hmmm.... I uninstalled Kies then I tried again with no luck... I re-installed the driver "Windows 7&Vista x64 USB Driver.zip" then I repeated the above steps then the download mode is back.... Weird isn't??? It looks like the Kies override the driver with another driver... So in order to get my procedure working make sure you UNINSTALL completely KIES from your system and install the drivers that I mentioned... Also notice that adb.exe detects my device and it wasn't before... Now I have the Downloading mode but I don't know what to load Hope that anyone can point me where I can download the original firmware that comes with Bell i9000M model...
DeCoDish
Click to expand...
Click to collapse
I did everything step by step...
but now my phone doesn't even starts, it's like it died litterally...
any ideas...???
ANYONE...?????
xero2002 said:
So you just randomly flashed a file to your phone, not even knowing what it is or does?
Just for the fun of it?
And you're wondering why your phone is now fked?
Do a full reflash with PIT, CSC, MODEM and PDA.
FFS...
Click to expand...
Click to collapse
how do we do this since the phone does not even starts...
not even with the key combination...
SOLVED
You need to hold the power, vol down and home key down and then put the battery in.
"5- Select your file PIT, PDA, PHONE and CSC then click on START"
Where can i get these files? I got my phone into this state through some ****ty app, i dont need to be told how dumb i am, if you can help this is greatly appreciated.
Can anyone please share the file Windows 7&Vista x64 USB Driver.zip ?
Thanks
Related
So I tried updating to the newest Cyanogenmod Beta1 when it failed to boot repeatedly I went to reflash via Odin using stock JM9 with repartition 803.pit. This is what I got on Odin:
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> modem.bin
<ID:0/004> modem.bin
<ID:0/004> Removed!!
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
I had selected the modem and rom file that came with the samfirmware.com package.
Now phone will not even turn on, react to button presses, or show that it is charging while plugged in.. Tried taking out battery and putting it back in a few times with no luck.
This is an international version of the phone. Am I screwed? Could the battery have died while flashing or could the bootloader have been messed with?
I am panicing
Did you find a solution?
I have run into the identical issue and was wondering what your solution was?
I flashed the Vibrant firmware by accident onto my GT-i9000m and now the phone is dead, no boot screen, no logo, no reaction to any button combo.
I previously used the usb jig to get into the download mode, and when I reflashed a known to be good rom back on the phone I checked off "update bootloader" assuming the bootloader was at fault. Big mistake.
I've ordered a replacement phone from Bell, but if you have any info it would be greatly appreciated.
Thank you in advance.
I'm having a bit of trouble flashing froyo with Odin (it sucks that neither Samsung nor AT&T will just release an official build). My phone is rooted, and I have installed the proper Samsung and USB drivers. I run Odin as administrator and connect my phone via USB, putting it in download mode. When I hit "start" Odin gives me a bit of progress, but the phone simply sits there. I've tried multiple times and have had it sitting here for close to 30 minutes, stuck on the downloading screen. Any suggestions?
Here is all I get from Odin:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
sammusashi said:
I'm having a bit of trouble flashing froyo with Odin (it sucks that neither Samsung nor AT&T will just release an official build). My phone is rooted, and I have installed the proper Samsung and USB drivers. I run Odin as administrator and connect my phone via USB, putting it in download mode. When I hit "start" Odin gives me a bit of progress, but the phone simply sits there. I've tried multiple times and have had it sitting here for close to 30 minutes, stuck on the downloading screen. Any suggestions?
Here is all I get from Odin:
<ID:0/004> Added!!
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> Completed..
<OSM> All threads completed. (succeed 1 / failed 0)
Click to expand...
Click to collapse
Don't waste your time with this, come see us over at Phoenix.
http://forum.xda-developers.com/showthread.php?t=892973
Click the link in my signature to see more.
Captivate
Eclair 2.1, rooted
1012 REV0.4
Ran Odin for the first time:
Opened Odin, turned phone to download mode, plugged phone in, started odin.
at that point odin didn't see any issues with my phone and ran unhindered.
upon reboot it got stuck in the now infamous world phone loop.
At first I couldn't get back into download mode => so I made a plug in jig(now getting in d/l mode is easy)
Tried to run odin again and it just ran perfectly like before and upon my phone's reboot... it goes back into the boot loop.
Did this little dance around 10x now...
my computer does not recognize the device but odin does...
Help would be appreciated seeing as how this is a common occurrence through out the forum from my observation.
kang0saur said:
Captivate
Eclair 2.1, rooted
1012 REV0.4
Ran Odin for the first time:
Opened Odin, turned phone to download mode, plugged phone in, started odin.
at that point odin didn't see any issues with my phone and ran unhindered.
upon reboot it got stuck in the now infamous world phone loop.
At first I couldn't get back into download mode => so I made a plug in jig(now getting in d/l mode is easy)
Tried to run odin again and it just ran perfectly like before and upon my phone's reboot... it goes back into the boot loop.
Did this little dance around 10x now...
my computer does not recognize the device but odin does...
Help would be appreciated seeing as how this is a common occurrence through out the forum from my observation.
Click to expand...
Click to collapse
What did you flash with odin?
sorry i should have clarified
it was I897UCJF6-final-OCD-REVO
Odin3Excecution v1.00
Windows XP - Laptop
here's the message script if there's anything weird:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> Sbl.bin
<ID:0/008> boot.bin
<ID:0/008> cache.rfs
<ID:0/008> dbdata.rfs
<ID:0/008> factoryfs.rfs
<ID:0/008> param.lfs
<ID:0/008> zImage
<ID:0/008> modem.bin
<ID:0/008> cache.rfs
<ID:0/008> Removed!!
Happened to me too. I suspect you have a 1010 or higher build phone.
I think you need the 2.2 (Froyo) version of Odin.
It's here http://forum.xda-developers.com/showthread.php?t=797282
Get to download, flash with that and you should be good to go.
kang0saur said:
sorry i should have clarified
it was I897UCJF6-final-OCD-REVO
Odin3Excecution v1.00
Windows XP - Laptop
here's the message script if there's anything weird:
<ID:0/008> Added!!
<ID:0/008> Odin v.3 engine (ID:8)..
<ID:0/008> File analysis..
<ID:0/008> Set PIT file..
<ID:0/008> DO NOT TURN OFF TARGET!!
<ID:0/008> Get PIT for mapping..
<ID:0/008> Firmware update start..
<ID:0/008> Sbl.bin
<ID:0/008> boot.bin
<ID:0/008> cache.rfs
<ID:0/008> dbdata.rfs
<ID:0/008> factoryfs.rfs
<ID:0/008> param.lfs
<ID:0/008> zImage
<ID:0/008> modem.bin
<ID:0/008> cache.rfs
<ID:0/008> Removed!!
Click to expand...
Click to collapse
This is the leaked version of froyo. It worked for me just fine but this was back in August and I have an older phone. As mxracer said, it may be due to you having a newer phone and the version DG posted might work for you. Check and make note of your phones build number for foture reference as some things may not work on your phone. This number is located under the battery. (Four digits, starts with 10xx)
You should really check us out over at Phoenix if you want some real kick azz froyo 2.2.1
This stuff is kinda outdated.
Go here http://forum.xda-developers.com/showthread.php?t=892973
Also click the link in my signature.
mxracer101 said:
Happened to me too. I suspect you have a 1010 or higher build phone.
I think you need the 2.2 (Froyo) version of Odin.
It's here http://forum.xda-developers.com/showthread.php?t=797282
Get to download, flash with that and you should be good to go.
Click to expand...
Click to collapse
THANK YOU VERY MUCH SIR!
all I needed was a new version of Odin for the 1010+ builds
hopefully this helps other ppl out too who r stuck
First of all I'm a beginner in android world .
Kernal: 2.6.32.9
[email protected] #1
The problem is:
I was trying to root my Galaxy S I9000 following the steps of [GUIDE] And then there was ROOT !
Everything was great until this step:
- Press "Start". ODIN you should now be flashing the kernel, and the device should reboot.
Odin gave me a red flag with " Failed " and I got this message:
<ID:0/009> Added!!
<ID:0/009> Odin v.3 engine (ID:9)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> zImage
<ID:0/009> NAND Write Start!!
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I unpulged my device and turned it off, when I turned it on a device-!- computer screen appered, after many tries I took off the battery and put it then I pressed the three combo button, finally I managed to get to download mode.
Now:
-My computer recognizes the device but Kies doesn't ( although it's the latest version and I tried to reinstall the drivers.)
-Odin keeps giving me the same error, and sometimes it stay stop at <ID:0/009> SetupConnection.. ( I tried XWKDD_insecure.tar & KE2_original.zip )
-I'm stuck in download mode.
Please help me get my phone to work (I prefer to return to the same firmware if it's possible).
https://www.wuala.com/Samsung Galax...and Odin/Original Firmwares/?key=AfzUZSU4SpKU
Download your original firmware from here and flash it in odin.
E: Btw are you using latest odin?
I got same problem when i m newb so calm down first go to www.samfirware.com and select ur phone download latest europen rom it is JVR and then flash them via odin by putting file respectively
Sent from my GT-I9000 using XDA App
Hello.
I do not know if the title is good. I will explain here what happened.
my Galaxy S was android 2.3.4 jvq. I wanted to intall a newer one, a android 4.4.x
I followed a thread about how to do that.
I tryed to root the phone uing Odin and cf-root, but it failed it. After that when i powered on the phone i get some error with phone to computer and a yellow triangle in the middle.
I founded a program on internet to "unbrick" that, but now i can only enter in download mode using the 3 buttons, and dont start in normal or recovery mode.
I tryed to flah it again uing odin with cf-root but failed every time.
the odin log says this :
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> zImage
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Do you know any solution to my problem?
Thx.
maybe this will help
GabrielAK89 said:
Hello.
I do not know if the title is good. I will explain here what happened.
my Galaxy S was android 2.3.4 jvq. I wanted to intall a newer one, a android 4.4.x
I followed a thread about how to do that.
I tryed to root the phone uing Odin and cf-root, but it failed it. After that when i powered on the phone i get some error with phone to computer and a yellow triangle in the middle.
I founded a program on internet to "unbrick" that, but now i can only enter in download mode using the 3 buttons, and dont start in normal or recovery mode.
I tryed to flah it again uing odin with cf-root but failed every time.
the odin log says this :
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> zImage
<ID:0/005> NAND Write Start!!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<ID:0/005> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Do you know any solution to my problem?
Thx.
Click to expand...
Click to collapse
Hi
did you already try to get back to 100% stock ROM??
-
-
i can not yet post links but if you google "galaxy s stock rom" and than the first link.
take a look here for the stock ROMS
http://www.sammobile.com/firmwares/database/GT-I9000/
it warked with another version...strange thow.
Thx.
I will try now to put again the 4.4.x