Database Develop

Rom DUMP; Portuguese Qtek 1.40_142_1.12.00 (Edit)

Hi all.
Because in Portugal, garanty of devices are made by the rom they had when are bought, have dumped a rom from a 9090, bought in 8/6/2005.
Made a dumped rom with the instructions taken from wiki:
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel
Will upload to FTP as ROM_9090_WWE_portuguese.
Devices says:
ROM Version 1.40.00 WWE
rom date: 03/10/05
radion version: 1.12.00
protocol version: 1337.42
extrom version: 1.40.148
Hope MDAIII will update wiki, cause there are some carrier cabs from TMN.

Moved file from uploads
Renamed File
Renamed thread
Opened New Dumped Rom page on wiki
Linked file
File can now be found under:
ftp://xda:[email protected]/DUMP_QTEK_14000_148_12000_portuguese.rar

Hi there,
I'm a newbie to the forum and I've seen this ROM update to portuguese language.
I've been to the wiki blueangel forum but couldn't find anything to assist me in the update procedure, because the decompressed rar file show only one file named "XDAIIs.nb1" and no other kind of software to transfer it to the Qtek 9090.
Does the file needs to be changed into another type, or can it be splitted ?
Thanks is advance.
Best regards.

Did you think of reading the instruction on wiki that are in the link of the first post.
How to Restore
Insert SD Card to XDA IIs.
Enter to Bootloader Mode by press Power + Record Button and Soft Reset Pictures Here
There will be question, asking for dump ROM from SD card or not.
How to store SD Card data to PC (Must have SD Card Reader) inorder to use SD card for other purpose.
Download ntrw.exe
Copy ntrw.exe to C:\
At Dos Command Prompt goto C:
Type ntrw read XDAIIs.nb1 E: file XDAIIs.nb1 is the rom name (actually you can assign any word) and E: is Drive of SD Card Reader
You will see file name XDAIIs.nb1 at C:
Then you can format SC card, that's all.
How to write saved rom file to SD card.
Type ntrw write XDAIIs.nb1 E:

Need some advice
Anyone has tryied this rom, i have downloaded from the site but i dont know if it works, iam portuguese so if anyone had use this rom please say it.
Thank you

9090 dead after flashing.....

My Qtek 9090 Dead after or in time flashing
I try .....
1. Flash with NO_ID
2.TRy via romupdate and nb1-file
3. Try via I-mate and T-mobile roms includes NO_iD
and nothing... only dark screen and USB or Serial string......
HELp plz.

...... and IF I insert in it SD card string serial no change after put him in cradle.....

What you can try.
if you have the seral message on your screen then just replace it in cradel and rerun the no_id application.
Are you SURE that you are using a valid ship.exe file and that you have extracted all the files and are following the upgrade instructions for 1.42 as per wilki.

MDAIIIUser said:
What you can try.
all THAT MAY BE
if you have the seral message on your screen then just replace it in cradel and rerun the no_id application.
Yes try, i start no_ID (with many roms) and 9090 waiting 20-30 minutes after this connection error
Are you SURE that you are using a valid ship.exe file and that you have extracted all the files and are following the upgrade instructions for 1.42 as per wilki.
Yes I extract all files , I try many ROMs for I-mate , Qtek , T-mobile in various version ..... I try make SD-Card with dump of rom,......
Only one that i cannot see How Update 9090 from SD to ROM or how copy dump of the ROM from harddrive via MTTY to 9090
This`is Unreal I work with PDA 3,5 years ago but look this bugs first ........
Click to expand...
Click to collapse

We have had a few (very few) that were not able to do an upgrade form thier pc. Not sure if this is a USB issue or software but after all the suggestions that we gave these people and none of them worked all they had to do was move over to a different pc and it worked.
So we know that the wiki 1.42 upgrade page works, that the file works and that the instructions are correct. Best for you is to try a different pc.

Need some help

I'm completely new to all of this....so forgive me if I posted this in the wrong spot, or the answer is posted somewhere (I already looked around for the answers, and didn't find them).
I want to upgrade my Blue Angel to the new ROM....and there are a couple things in the instructions that I don't understand how to do:
1) "Resize your Extended ROM to 128KB and your Storage ROM to 60MB. You will use your SD card as a replacement for your EXTROM."
2) "Modify the operator in the ROM as needed:
* Determine your operator Information e.g.: "T-MOB101", or "Vodafone", or O2. See GetDeviceData.
* Open a command prompt, go to the folder where the ROM file resides (nk.nbf) and execute: SetOperator ???"
With the second one, I've already used GetDeviceData to find out that my operator is "XGULA001".
Edit: Another question that I have.....is Windows Media Player 9 included on this when I install the ROM? (if not, will I be able to install it later?)

Please someone answer, I know that someone has to know how to do this.
1. Modify the operator in the ROM as needed
Open a command window and execute: SetOperator ????
- Replace ???? with your Operator Information
- i.e.: T-MOB101, or Vodafone, or O2, or ...
I have no idea what I'm suppost to do, but I do know what my operator is.

read section 'How do I find out what my device configuration is before upgrading?'
http://wiki.xda-developers.com/index.php?pagename=BA_GettingStarted
download and extract the file i uploaded, copy nk.nbf over the extracted director. launch your dos prompt, nagivate to the extracted directory, and run SetOperator.bat.
example: SetOperator.bat O2ASI001
where O2ASI001 is the operator code.
hope it works.
imatrix

Thanks, thats the program that I needed......but now I have another problem.
When my BA is in bootloader mode, I can't update because the updater doesn't recognize the BA. When I try updating out of bootloader mode, the updater recognizes it at first..,...but when I start the update it goes into bootloader mode again, and it stops recognizing the BA so it can't update.
What can I do to solve this problem?

what error did u get?

Remove SD Card
Make sure you remove your SD card before you start the flash program. I have noticed the same problem if my 4gb SD card is still in the slot. After upgrading, you return the SD card in the slot and reset the device so the EXT-ROM directory can be read.

Thanks, that fixed the problem.....but now I have yet another problem.
The phone won't work, and I can't connect to my operator.....how do I connect to my operator? (My operator isn't listed anywhere on the BA)

Which CHEEIMG file?

Having downloading the WM6 update from Palm, I keep getting the Unsupported Device Error (even though it's an English Treo 750v). I've extracted all the update files from the tmp folder. Which CHEEIMG file do I load on to a card, there are the following.
CHEEIMG.MD5
CHEEIMG.NBH
CHEEIMG_FW.MD5
CHEEIMG_FW.NBH
Cheers

Rename CHEEIMG_FW.NBH (about 80 MB) to CHEEIMG.NBH and flash with it.

Cheers, that did it, upgrade successful

I put the CHEEIMG.nbh in my treo750v...push the lateral button and reset..but nothing happend.. appear 4 colour bands.... "serial" down...but NOTHING more ¿?.
Where is my mistake ¿?
Thanks in advance for your help.
Abraham
I have 1.12 in my treo750v [spanish] and I try to put wm6 [english version] I understand it is possible... ¿?

Make sure the cheeimg file is in the root of your miniSD and that your miniSD is formatted FAT32..

cant flash ROM to X1 - can someone help?

I am trying to different ROMS to my X1.
The first one i tried was S4_v1.6_WM6.5.5-full-23549_XPERIA_X1_13.04.2010
The first time i connected my X1 via USB to my PC.
- I started the included CustomRUU.exe file and went through all the dialogues.
- The X1 restarted by itself an showed
KOVS110
SPL-0.78.0000
MicroP1-787
MicroP2-707
- Then a process bar appeard that freezed at 0%
- after some seconds the software on the PC told me abput a connection error 262 although it was able to read the software Version of the X1 before.
- The next step i tried was to copy the file onto the SD Card. I formated it in the SD card slot of my notebook with FAT32 (no fast formating).
- Then i copied the image file onto the card and renamed id to kovsimg.nbh
- I made a hard reset
- The X1 said "no image file" an showed again the colour screen.
- The next step i tried was to format the SD directly in the X1.
- So i configured the X1 for accessing the sd card as a harddisk. It appeard in the Windows explorer and i was able to format it.
- I copied again the kovsimg.nbh file
- after the hard reset the X1 shows "Loading..."
- i waited for half an hour but nothing changed.
What i am doing wrong?
What is the difference between CustomRUU.exe and X1_HardSPL.exe?
Do i need an other version of SPL (for example 0.72) and where can i get it?
I wanted to test WM 6.5 in order to get again a bluetooth connection to my Opel Vectra CD70. I other threads some people said that this would be the only way to get this pair running.
I would be very happy if someone could give me an useful tip without all the abbreviations that an newbie will never understand.
Thanks for your help
matthias

I think you didn't h-spl (from sticky olinex thread) your phone, which is absolutely mandatory
otherwise it would show
...
SPL-0.72.OliNex
...
in your bootloader
pls confirm

Hi DrakenKorin,many thanks for your fast reply.
I dowloaded X1_HardSPL_v1.zip from the thread Olinex Hard Spl.
I unzipped the file and got one file called X1_HardSPL.exe
By clicking this file the aplications comes up an some other files will be uncompressed in the same directory.
The appilcation is reading my current Image Version 1.05.207.13 and would like to update it to 1.00.X1
When i start the update the X1 will reboot an now shows 0.52.OliNex
Waht should i do next?
Thanks for your help

Hab's geschafft.
It is running with WM 6.5
I thing my fault was that i did not see the difference between the OliNex Hard-SPL and the the customRUU.exe
Thanks for your help.
Regards
Matthias

congratz, was busy and just wanted to start answering your previous post when I saw your update
enjoy your wm6.5.X experience