Related
Hello guys!
I got my MDA Vario last week, and I am very much impressed with it!
I got the MDA Vario brand new without a contract and my intention is to use it with one of those O2 Genie PAYG SIM cards. So.... after much reading this excellent forum I figured out that I would need to unlock the SIMlock on the Vario. Got hold of the Lokiwiz utility, followed the advice on these forums, and tested it with the Orange SIM in my regular phone, and hey presto.... MY PY PHONE IS UNLOCKED!
Next step - to remove all T-Mobile customisations. Again, I had a simple bit of advice from one of you good folk - hard reset, then soft reset when the phone starts to install customisations and now all the pink girlie stuff has gone! Only reminant of T-Mobile left on the phone is the logo on the phone dial keypad.
My thoughts are now with upgrading the ROM. T-Mobile have been very slow with updating their ROM package -a new one is apparently due very soon. Now.... in preparation of installing a new ROM, Ive CID unlocked my phone. I would really like to know which ROM I should upgrade to - there are so many out there! As the phone has been CID & Sim Unlocked, does the phone remained unlocked irrespective of what ROM I install? Can I install a T-Mobile ROM after changing it to another?
As I intend to mostly use an O2 PAYG SIM in it, would it be better to use a new 02 update? If so, which one? Or do I go for another ROM? All very confusing! Finally, Ive heard that I cannot browse the net via GPRS on an 02 PAYG SIM. Is that true? Do I need to flash an ExtROM too?
I know Im asking a lot here and am being a bit of a pain in the backside, but I would really appreciate any and as much advice as possible as I realy dont want to end up with a dead phone! Many thanks in advance!
Hi, yes you could wait for the new rom and i am a believer in sticking with your manufacturer roms because many of the posts here seem to people experimenting with different roms and it all going wrong - lol.
But if you do upgrade proberly the commonest choice is the aku2 qtek rom that i use
download here ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
and the o2 aku2rom not a bad idea too, but without the o2 extras.
Yes you could then upgrade to the t-mobile rom then but often you need to unlock again with lockiwiz 0.3a.
PAYG o2 will browse internet but msn etc.. does not work.
btw yes you are a pain in the arse but then most people here are!! :lol:
Cheers Mark! Nice to have some basic advice - very reassuring for a thicko newbie like me!
Well... I couldnt wait for the new T-Mobile ROM and went ahead with the upgrade with the Qtek upgrade you suggested.
Was a little tricky at first because the upgrade wouldnt happen (port failing to open) but I had a few programs running in the background on my desktop PC and shut them all down so that I had a `Clean` PC. The upgrade process was then as smooth as a babys bottom.
MDA Vario is running really well - well worth the upgrade IMO. Everything seems quicker and generally better. Only problem I have is with wifi - it seems to take ages to make a connection with my PC (ad-hoc peer to peer) whereas on the original T-Mob ROM it was very quick. Any ideas here?
I read that you say I would need Lokiwiz 0.3a to install the AKU2 T-Mob ROM when it is eventually released. I was under the impression that once the PDA was unlocked (lokiwiz 0.2b) I wouldnt need to unlock it again. Is it different with the very latest T-Mob ROM? Can I not revert (downgrade) to the original T-Mob and then upgrade to the new T-Mob ROM? Ive not heard of lokiwiz 0.3a being out yet - would it be as simple as unlocking with lokiwiz 0.2b?
Finally, how on earth do I get the latest 02 ROM? I need to enter my 02 mobile number and IMEI to download it. Do I need lokiwiz 0.3a to install that or any other current ROM?
Cheers for your friendly advice.
Al.
Hi, no problem - glad to help.
Lokiwiz 0.3a is out see here http://forum.xda-developers.com/viewtopic.php?t=50768
For some reason when upgrading (in think it renews cid/spl) to aku2 rom seems to lock again - i had to unlock my qtek with above tool.
Yes you can go back to original rom - but if does not work use farias method of unlocking and downgrading rom (post is in this forum)
Most of the roms are in the wiki http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
including the o2 roms, but i would refrain from too much chopping and changing because you can destory the bootloader and then has to go back to the manufacturer.
Many reported problems with the wifi setting up - i would read some of the threads in the wizard forum if i was you. First thing to try is tweak wifi on device to wlan g and it may work better.
see registry tweaks here http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
btw good to hang out in the wizard forum too - you will learn alot of tips from there.
Want to also say thanks from another newebie with T-Mobile MDA. Have unlocked phone and CID and flashed with 2.17 QTEK ROM and all is good.
Thanks !!!
if you want th get rid of the tmobile crap on the face...use a 2p coin and move it downwards...not accross
it takes the tmobile paint etc off without any marks..
Jesus sbouri that logo was killing me, brilliant tip, nice one mate!!!
hi
i just got my mda vario and manage to unlocked the phone with lokiwiz03. i know my phone is now sim unlocked, but how do i check if it is cid unlock as well?
i am eager to flash the rom with the qtek version but i have no idea how to do it.
i know i must have my phone cid unlock in order to install a different rom, so do i just download the latest qtek rom, connect my device to usb and activesync it, and then just run the RUU?
i am really noob here.
cheers.
Hi mate if i was you i would use MR CLEANS ROM i flashed with that and its excellent, tottaly clean with no tmobile crap and i didnt do anything with the cid so dont worry.
ftp://xda:[email protected]/Uploads/Wizard/ROMS/MrClean_RUU_WIZARD_224_AKU23_WWE.zip
Just download this and run follow instructions, real easy. Good luck mate.
thanks for the advice...i took a bold move and flash it with a qtek rom. works like a charm. before that i did cid unlock using lokiwiz02a, not lokiwiz03.
i will take a look at mr.clean rom at a later stage.
i notice that my imei number is different from the one in my box. does flashing the rom change it?
now my next task would be update to a better radio rom and check out the extension rom.
cheers.
SBouri said:
if you want th get rid of the tmobile crap on the face...use a 2p coin and move it downwards...not accross
it takes the tmobile paint etc off without any marks..
Click to expand...
Click to collapse
Great tip, worked like a charm and left no marks.
Thanks.
Hi there, I'm about to flash my UK MDA Vario too.
I'm not sure to use the Mr clean one or the Qtek 2.17 version.
Before I do anything, which is better of the two?
Also, what settings to I need backed up? I have my txt msg service numbers, as well as voicemail. And all of my MMS & GPRS settings.
Am I to assume that all I have to do is input the settings into the device once it's been flashed?
Thanks
Scottland said:
Hi there, I'm about to flash my UK MDA Vario too.
I'm not sure to use the Mr clean one or the Qtek 2.17 version.
Before I do anything, which is better of the two?
Also, what settings to I need backed up? I have my txt msg service numbers, as well as voicemail. And all of my MMS & GPRS settings.
Am I to assume that all I have to do is input the settings into the device once it's been flashed?
Thanks
Click to expand...
Click to collapse
The mr clean rom is a more advanced rom and has no extras. The qtek official rom is probably a safer install because its an official rom and many good reports of success and users pleased with the outcome.
Yes when you have flashed just input all those settings again.
Plus you can backup your voice tag database between hard resets by copying the file CommandModel1.bin found under the windows folder to your pc or to the memory card. After rom upgrade copy it back to your windows folder and all your voice tags are back!
Create backup of windows\start menu - most programs that are on the storage card dont need a reinstall.
Create copy of pim.vol in the root directory of the device - contains contact and appt information. After flash change the new pim.vol to pim.vo and copy and paste old pim.vol (use total commander or gsfinder file explorers for this) and soft reset and you will have info back.
Create backup of windows\favorites - for all your internet favorites.
That will make restore a bit quicker than otherwise.
Cheers for the info. I was actually thinking of trying the Mr. Clean one first, is there anything missing from this one, or is it just less stable?
Mr clean is just a clean rom without any of the manufacturers addons. It will probably run very well - its the flashing process with it that may not be as safe as an original rom and may possibly destroy your bootloader etc.. so you have a brick phone. I would always go for the safest option and would not suggest chopping and changing roms. Read the many users stories where everything goes wrong and the forum needs to help them out.
meschle said:
Mr clean is just a clean rom without any of the manufacturers addons. It will probably run very well - its the flashing process with it that may not be as safe as an original rom and may possibly destroy your bootloader etc.. so you have a brick phone. I would always go for the safest option and would not suggest chopping and changing roms. Read the many users stories where everything goes wrong and the forum needs to help them out.
Click to expand...
Click to collapse
True, I didn't think about that. Thanks again.
Ive been using Mr clean rom for 1 week now and its excellent from my experience. Its tottaly clean and runs so fast!
By clean i mean it has no customizations as you will find on official roms. It flashed just like any other rom too. Easy as pie. Just my info as people would like to know.
I've just upped to the QTEK ROM, and I've a couple of problems, nothing too serious though I don't think?
Firstly, when making my GRPS connection - I can't seem to find anywhere to input the WAP Proxy settings?
Edit, sorted this one now
Secondly, when settinp up my MMS - I can't select connect via Picture Message in the settings, it's not there?
I'm guessing this is some other connection I have to make up?
Any idea guys?
Scottland said:
I've just upped to the QTEK ROM, and I've a couple of problems, nothing too serious though I don't think?
Firstly, when making my GRPS connection - I can't seem to find anywhere to input the WAP Proxy settings?
Edit, sorted this one now
Secondly, when settinp up my MMS - I can't select connect via Picture Message in the settings, it's not there?
I'm guessing this is some other connection I have to make up?
Any idea guys?
Click to expand...
Click to collapse
I cant find what you say under settings - what does it do?
Never mind ignore me, that'll teach me not to read T-Mobile's site correctly
Sorry, but i am a newbie i just got my MDA, it sometimes freeze up on me, so i talk to a friend he said try upgrading the firmware, so i wanted to upgrade the firmware just dont know which one cause there's so many...i wanted Tmobile USA, with all of the Tmobile programs such as MMS, Tzone, Email basic program from Tmoile...thanks alot- looking for something more stable, maybe faster WIFI, bluetooth those good stuff any recommandation would be great..and another question when i TRY to flash the fireware will i lose all of the data or program like the spb, theme and whether program thanks again sorry for all the question but i know you guys can help
I am using Rom- 1.8.10.2.WWE
ROM DATE-12/10/05
Radio Version-01.09.10
Protocal version-4.0.13.20
Extrom version 1.8.10.104
Not trying to be rude, but you really need to spend a week or two reading the threads in the "Wizard Upgrading" forum before you even thinking of flashing your Rom.
FYI firmware is for cellphones, Roms are for Windows Mobile Devices.
As to which Rom to use, that depends what you're looking for.
You can go for the latest, the most stable, or one that supports a specific feature. Again this is somethign you really need to read-up on. If you are looking for a specific feature use http://forum.xda-developers.com/search.php .
Honestly, you will gain speed and stability with any 2.x Rom.
To use one of the custom Roms you will need to CID unlock your device (search for it) first.
For your first flash you might just want to stick to an official Rom.
First, don't even think of attempting a CID unlock until you figure out if you have a G4 chip or not, unless you want to turn your MDA into a brick. There are other articles on the unlocking forums, as well as the Wizard forums that go into this in detail.
Until this is ironed out, I'd consider paying $40 to the guys at www.imei-check.co.uk. I've not heard any bad press about these guys, so if you want a SIM/CID unlock, go here.
If its freezing up on you, I'd consider backing your stuff on it, doing a hard reset, and restoring it. Make sure you have the data backed up (if ActiveSync doesn't have it, there are other backup utilities which can work well for your MDA you can purchase.) If you are getting freezes with just the factory installed stuff on it, you may have a hardware issue.
Lastly, quite a number of things can be enhanced/fixed without a ROM reflash, so unless T-Mobile USA comes out with new downloadable ROMs, I'd not worry about a reflash just yet.
hieu512 said:
Sorry, but i am a newbie i just got my MDA, it sometimes freeze up on me, so i talk to a friend he said try upgrading the firmware, so i wanted to upgrade the firmware just dont know which one cause there's so many...i wanted Tmobile USA, with all of the Tmobile programs such as MMS, Tzone, Email basic program from Tmoile...thanks alot- looking for something more stable, maybe faster WIFI, bluetooth those good stuff any recommandation would be great..and another question when i TRY to flash the fireware will i lose all of the data or program like the spb, theme and whether program thanks again sorry for all the question but i know you guys can help
I am using Rom- 1.8.10.2.WWE
ROM DATE-12/10/05
Radio Version-01.09.10
Protocal version-4.0.13.20
Extrom version 1.8.10.104
Click to expand...
Click to collapse
Sorry for butting in
Well i have this wiza200 tmobile MDA and would also like to Flash it because of speed and performance enhancement my question is when i flash a new rom will it make my phone again sim lock? because right now its already sim unlocked
my wizard came in with the stock rom any enlightenment will be greatly appreciated
Thanks
Aloha everyone,
I have tried to not post for about 3 weeks but I just can't move forward. I have read and tried to follow everything on the site but I am just confused. I know this is a developers site and I am very intimiated to be castigated by you guys but...it's the internet so what the hell.
I have found numberous instruction threads pertaining to updating ROMS on the Wizard. It seems that up until recently there was only one way to do things but now there are many. As I try to answer questions I come into conflict over which way I shoudl be heading.
I currently have a working WIZ100 that boots with IPL 2.21.0001 SPL 2.21.0lip with GSM 2.25.11 and OS 2.25.11.1. I somehow got to this point, I think by following the instructions to get hardSPL on my device and booting on startup. I did not know if I next needed to find a ROM and if so then how to get that ROM activated on my device or what programs to do this with. I know that the threads spell it out but the threads pertain only to direct assumptions; the assumption that my head is not in my ass.
I wanted to attempt to put a new rom on here, for fun and to play around with something new. Perhaps increase reliability or to get WM6 going. I am stuck now though. Part of me wants to turn back and load the original ROM from the HTC site and the other part of me wants to try a new ROM as I already have this thing booting to the 0lip SPL.
Is anyone out there willing to help me either via this thread, personal message or IM?
Since you have already installed Hard SPL you should be safe to go ahead and pick virtually any ROM you choose on there. I don't have a lot of experience with Hard SPL yet, except for installing it on my kaiser, but the one thing I would guess that you should make sure that the ROM you want to flash doesn't have would be an IPL/SPL update included. As far as I know, I don't think any of the public ones that you find on here have them but make sure you read the chef of the ROM's entire post to make sure. And, if you magically happen to find my ROM somewhere, which you shouldn't since I only gave it to 2 people to try, don't flash it because mine does include an IPL/SPL update.
From my best understanding you have already loaded HardSPL and now are CID unlocked. If this is the case then I would recommend going forward and flashing a new rom to your device. Just go to the Wizard Mobile 6 thread and find one you like, and flash it.
Simple as that.
I appreciate your replies.
1) I am clarified like butter! What program do I download and use to flash the ROM to the Wiz, this has been a source of confusion for me.
2) If I download and install the HTC Cingular ROM from HTC, will that overwrite the HardSPL and return my phone to Factory Default, including the radio areas? In other words do I rid myself of 2.21.0lip?
Thanks for not beating my head in...very polite you devs are...
I like beating people's heads in, and you are far too polite, that I am actually having a very slight guilty twinge! Damn you. I have a G3 myself so I cannot help much, however, I found this sticky which may help.
http://forum.xda-developers.com/showthread.php?t=332320
I do know that once you choose your rom, you open the folder and run the item marked as ruu.
Now if you only had a G3, then I could fry you like the noob you are.
I suppose at some point, I should make a point of reading/learning about G4's. I know they are a far different animal from my G3.
That's the reason I said not to flash a ROM that contained an IPL/SPL upgrade since there is the possibility that it may overwrite Hard SPL, although I'm not positive of that, but better safe than sorry especially if it it's not an official ROM that carries the correct IPL/SPL format for a G4. If it doesn't contain the correct format for a G4 it could ruin your phone. If you flash an official ROM though and it overwrites it you can always just reinstall Hard SPL again and keep flashing. I hope this makes sense.
As for the files you need to flash a new ROM, they're usually included with the ROM. If they're not then just let me know and I'll upload them for you.
Good that you asked before damaging your (expensive) device...
Every Flash version comes with a RUU (Rom Update Utility) you just run that proggy and it does the rest.
To make it easier, look for a rom that states it's G4 safe (no IPL/SPL included), so you don't have to mess around with the inner files. If you want to, begin your tests with the TNT series, the latest build, stated in my sig is G4 safe, after that you'll be able to know the initial procedure.
Good Luck.
Thanks for the info.
Do I execute the ruu from Windows XP or from the SD card ont he device?
Why am I have a hard time searching for and finding TNT 5.2.1921 TouchFlo ROM?
The rom update utlity gives me an error when I try to update. Should I try to do all this from the sd card?
Well, I am plugging along. I rebooted after an error 300 came up on the rom utility. Any suggestions for me?
I found this thread, back in business, thanks for your help guys.
I guess my only unanswered question is...if I use the HTC ATT exe from htc.com will it kill the hardSPL and restore the computer back to normal?
If you have ROM on your desktop, Connect your phone to your computer via USB, open up Activesync, uncheck the check box in settings that allows USB connections. Make sure you have at least 50% battery, then put your phone into bootloader mode. (soft reset while holding down the camera button- keep holding the button for 5 sec.) a tri-color RGB screen should come up. This is boot loader mode. Then run the rom update utility program, and everything is automatic from there on. once it is done flashing the phone will restart itself.
Thresher said:
I found this thread, back in business, thanks for your help guys.
I guess my only unanswered question is...if I use the HTC ATT exe from htc.com will it kill the hardSPL and restore the computer back to normal?
Click to expand...
Click to collapse
Try it and find out. I'd kind of like to know the answer to that one too, although my phones a G3 and already CID unlocked anyway. You can always reinstall Hard SPL over again if it does.
So this worked out well for me overall. Installing HardSPL to my G4, and then using a correct bootloader with the right ROM (to review).
I am having one issue.
I have the OEM ROM, however the RUU gives me an error. Is there a documented way to restore the phone to an original status? Is it even necessary?
I ask due to problems since my upgrade to the TNT rom. I am noticing a lot of missed calls and people have complained. Is this an issue with the 8125 and the particular ROM?
I don't know what to ask, or how to search for this. Thanks for any input you can offer.
Otherwise the TNT rom is awesome. I do miss the voice dialing though. Thats another search.
Actually, that's usually an issue with your radio version. Try using either version 2.19 or farias 2.69 and see if that fixes your problem. You should be able to find both of them in the wiki and you may want to try both of them and see which one gives you the better reception because sometime one will work much better than the other for you depending on your location.
By the way, you don't have to be CID unlocked or have hardspl installed to update your radio so you shouldn't have an issue with the RUU giving you an error. If you do, let me know and I'll upload a different RUU for you to try.
xeno1 said:
Actually, that's usually an issue with your radio version. Try using either version 2.19 or farias 2.69 and see if that fixes your problem. You should be able to find both of them in the wiki and you may want to try both of them and see which one gives you the better reception because sometime one will work much better than the other for you depending on your location.
By the way, you don't have to be CID unlocked or have hardspl installed to update your radio so you shouldn't have an issue with the RUU giving you an error. If you do, let me know and I'll upload a different RUU for you to try.
Click to expand...
Click to collapse
So the Rom is broken up into major parts. Those parts must ineract with one another, so that would be why my radio version may be at cause?
Yep. The ROM can contain the IPL, SPL, OS, Splash Screens, GSM (the radio), and extended ROM, any of which can be changed or upgraded individually without affecting the other parts of the ROM (for all intents and purposes anyway). That means you can change your radio version without it deleting all of your settings or your installed apps in your OS, etc etc.
Since you still upgrade each individual part using a RUU that is able to update any of the parts you still get a warning when you run it that it will delete all of your files, but as long as the update that you're running doesn't include a new OS you can ignore those warnings.
I decided to back out of the entire upgrade and move back to WM5 Official Cingular HTC ROM. I am stoked that I now know the full process of taking a G4 through hardSPL, ROM updates and restoral.
I was too scared to try any radio updates or fixes. Maybe when I upgrade phones I will come back to playing with the 8125 but for now, I just need a good functioning phone for work.
Do these Cingular radio fix cabs apply to a standard phone or only to upgraded ones?
Hey there,
since I'm new to the community I hope I'm not doing it wrong
I will receive my new Herald within the next days and now I'm seeking for all the stuff I will need then.
1. Hard-Spl. I don't get it. What is it? Is it some kind of firmware update or whatever? The ROM's thread says that I would need SPL 4 or later to successfully finish the Update but I can't find that SPL application in version 4+ :/
2. http://forum.xda-developers.com/showthread.php?t=437385 - http://www.evolvers.net/Herald_Roms/Version 7.7/ => I'd like to use that ROM. But I'm not too sure whether to use Manilla2D or Omnia.
3. What if I needed to send my device back for warranty reasons. Is there some way to flash back the standard Win Mobile 5.0?
I hope I will get your attention!
Regards,
Chris
Hey there,
A friend of mine just told me about flashing ROMs literally a few days ago. I did my first successful flash just yesterday and I am very happy that I did. FYI, yes I am using a stock TMobile Wing from 2007.
Rom's are not interchangeable across different phone models as far as I know. So you need to get ROMs made for the wing a.k.a. the Herald. Any Rom for the Herald should work.
Just remember one thing that I forgot to do, make sure that you back up your data. I forgot to do this and lost all of my data. Luckily, I did not have any pictures or music that I was too sad to lose. However, I did lose my contacts. Again luckily, I had an old Sim card from last year that had my contacts on it, so I was able to get back 90% of my phonebook, except for a few people that changed numbers or new contacts. So be sure to save anything you want to keep somewhere else.
I am pretty technically savvy, but I must say that flashing the Rom did take me several hours. The process itself only takes about 10 minutes, but it took hours to figure out what type of Rom I needed and how to exactly flash it. You will see many people trying to tell you that you need to know your IPL and SPL version, and there is no way to know this until you start flashing! It wasn't until I did my first accidental flash that it showed me this information, and this ended up being my first successful flash. After trying for several hours the night before and not succeeding, I guess that's why it slipped my mind that flashing successfully would erase all my data.
The one that actually worked for me was the Canonyang Rom. In the link below please look at post number 216, and you will see a link to download the ROM that worked for me. The file is "HardSpl_WM6".
http://forum.xda-developers.com/showthread.php?t=332413&page=22
I tried to flash directly to open touch, and no matter what I tried it was not successful. When I accidentally tried this Canonyang flash it worked successfully the first time, and after that now I was able to flash to any other Rom.
I am currently running open touch light version 6.5 because I read in another thread that it's supposed to be the fastest. I don't need a lot of features so I'm happy with what it has, and it is much, much faster than the stock T-Mobile Rom.
Since you are now getting it, yes, warranty is an issue for you. I am very new to all this, but from what I gather, once you flash, it does void the warranty. Perhaps someone else can answer if there is a stock TMobile rom, that you can flash back to. However, since the roms are digitally signed, I'm not sure that by even doing that, if TMobile can tell you modded it, and therefore elect not to honor your warranty. I guess that's a risk you have to decide if it's worth it or not. IMHO, I found out about rom flashing this week, and my warranty was up last month. However, if I had found out about this during my warranty period, I would have still done it. The Tmobile stock rom is sooo slow, compared to these roms. If you've never used these roms, you'd think like hey, it's got some bugs, but it's not that bad. But if you've used them, you're never going back to stock rom again.
I apologize if there are any typos, as I am using voice to text recognition software that I am testing. I thought I'd help you out by writing this as well as I test it. Good luck and let us know if you have any questions, we're all here to help.
Hey,
thanks for all the information. Was very helpful. I decided to you the ROM from that link. Should work, shouldn't it?
The only thing I don't get is how to get to SPL4+ :/ I heared of different methods of SPLing. Like Hard SPL and USPL. Can you bring light into that cave?
Cheers.
Hey there,
Your link goes to the Open Touch thread. The link I'm referring to, is this one:
http://rapidshare.de/files/38148213/HardSpl_WM6.rar.html
As I said, I was NOT able to flash directly from stock to OTP. I tried many methods, and Canonyang was the only one that worked for me. After I successfully flashed to CY, then I was able to flash to OTP without issue. But in theory yes, any Herald rom's should work fine.
In regards to IPL/SPL, my wing is from September 2007, and I had IPL/SPL both above 4. I had NO WAY to verify this before flashing. When I initiated the flash for CY, and the wing rebooted, it was THEN I saw my IPL/SPL versions. I'm sure yours will be at least v4.
Actually as I write this to you, I remember a critical step I forgot to tell you. You need to Application Unlock your device as well. This is probably what I was missing in my failed attempts. After I did that, then the CY flash worked. I got that information, from this link:
http://forum.xda-developers.com/showthread.php?t=356295
So I would suggest following the steps there first, then trying the link earlier to flash to CY, then flash to anything else. This is the procedure that worked for me. Good luck!
Hey there and thanks again for that bunch of information
itbmd said:
I'm sure yours will be at least v4.
Click to expand...
Click to collapse
What does that mean then? I do not have to HardSPL my phone? But still, would you mind telling my step by step (And I really mean step by step^^) how to HardSPL a device? I really do not want to brick my phone directly at the beginning.
Oh and what should I rather be using, SoftSPL or HardSPL?
Cheers.
Hey there,
Sorry but I just flashed my device less than a week ago as I mentioned. I don't have many of the answers you ask, because I'm asking them myself. I don't know the diff between Hard vs. Soft SPL.
The file I linked you to earlier, is a hardspl, as denoted by its filename "HardSpl_WM6". It hardspl flashes to the canonyang rom. It was then I saw the IPL/SPL versions, and then was able to flash to other roms.
FYI, I was concerned about bricking my device as well. But during the roughly 5 hours I was trying to flash it correctly, every time the flash failed, it did NOT brick. It just errored on the pc, and the Wing itself just restarted and went back to the stock TMobile rom. It never actually bricked. Make sure you do the application unlock though; I think that's a step that people may not do and could cause it to brick. Good luck.
Hi there, im fairly new to my Telus Diamond, i love this phone but its giving me some grief with the Touchflo3d being laggy etc...
Anyways I heard you can flash new ROMS that are custom and more stable and help out the phones performance a lot but i have a few questions before I flash.
Here's my phones specs before i ask my questions.
ROM Version: 1.06.661.1 (old i believe)
ROM Date: 07/21/08
Radio Version: 0.99.90v
Hardware Version 0080
and i dont think the rest is important.
And im usuing WM 6.1
ok now here are my questions:
1) If I flash to a cooked ROM, i heard it Erases EVERYTHING, so with that in mind, im a telus customer, does it effect my service plan, ex: can i still use my phone like i bought it and make txt msgs, emails, msn, phone calls etc.. or do i have to set it back up again?
2) Do i have to use the same Radio Version?
3) would my Current network number and Cureent Channel be changed? If so how does that effect my phone?
4) umm with my programs that are on my phone, ex: office mobile, WMP, MP3 trimmer remote desktop etc... will i still have those? Or will i loose the registration for them.
5) this is my last question i believe, would I have to dump my current stock ROM for a backup? Like is that recommended or is there a backup of my ROM already on this website.
I appreciate any help, and sorry for being such a noob. The only thing i've flashed before was a custom firmware on my PSP lol and that was reallly easy...
1)Yes it erases everything the easiest way to explain it is like this: "rom" stands for read only memory.... kind of like a cd rom. And the outcome is the same also, when you flash a new rom it is like writing a new cd image.
2) no you don't have to use the same radio version, but some roms will require certai n radios (most roms come packed with radios though so you shouldn't have to mess with it)
3) Flashing a new rom changes your phone but not your network (your number would still be the same)
4)You will lose anything you installed unless you back it up. Depending in the rom, office mobile and stuff like that might be preloaded.
5) There should be a backup on the website, a dump should not be necessary.
Again on the backup thing you will want to back up are your contacts sms emails ect anything you want to keep before flashing.
Flashing isn't hard, you just need to read the directions MAKE SURE YOU READ BEFORE YOU FLASH. like i said it isn't hard but if you don't read everything before you flash you may turn your phone into a very expensive paper weight.
PS here is a good place to start your reading:
http://forum.xda-developers.com/showthread.php?t=416211
Alright sweet thank you very much
Im not going to upgrade just yet though because i still want to learn more
about it and im iffy about it mainly cuz i still want to be able to make phone calls lol and i dont see anyone posting anything for the telus versions.
Oh and one more thing before I upgrade the ROM do i have to upgrade the HardSPL first? or can i just use the CID lock, then the ROM?
no, you defenetly would want to cid unlock first, otherwise you will trash your bootloader and brick your phone
ok so Cid unlock, HardSPL, then flash the rom
hard spl is cid unlock after unlocking you are free to flash away
Oh ok, gotcha haha
.. i hope
One more thing lol sorry...
Um that link you sent me for the steps
"[TUT]Complete upgrading guide (HardSPL+Radio+ROM) NOT FOR CDMA USERS!!!"
Well i dont know what CDMA means but Im pretty sure im a CMDA user. So is it safe to still fallow those directions? or must i need to do something different.
read post #4 in that thread, you can't miss it.
is it alright if my Diamond says DIAM500? on all the guides they say DIAM100, when you check the SPL, mine is stock and in the tri colored screen it says:
Security Unlocked
DIAM500 <------ (Do i have to find a ROM specific for this modle?)
SPL-0.57.0000 <------ (I dont see this ver. on the forums anywheres)
MircoP-Diam (LED) vB
PSOC-Diam STAGE_EVT v20
Serial
(its blank)
I didnt run any CID unlockers or anything, any insight?
Dang Telus...