Database Develop

Stuck at bootscreen after flash

I just flashed my Qtek 9100 with the T-mobile rom "RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe" from the ftp. I have tested a lot of different roms without trouble. But after the flash my Qtek is stuck at the bootscreen just displaying
IPL 1.06
SPL 1.06
GSM 01.12.10
Tried a hardreset and it says format complete but after a reboot I am stuck at the bootscreen again. I am terrified - can I make my beloved qtek to work again or is it just a piece of expensive junk now ?

Sorry, stupid me I was as easy as start in USB mode and reflash and it booted normally again

easycure1974 said:
I just flashed my Qtek 9100 with the T-mobile rom "RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe" from the ftp. I have tested a lot of different roms without trouble. But after the flash my Qtek is stuck at the bootscreen just displaying
IPL 1.06
SPL 1.06
GSM 01.12.10
Tried a hardreset and it says format complete but after a reboot I am stuck at the bootscreen again. I am terrified - can I make my beloved qtek to work again or is it just a piece of expensive junk now ?
Click to expand...
Click to collapse
I am in the same situation now..
I am trying to re-flash the original ROM now, enter the booloader menu by holding voice-dial+CAMERA while resetting. then connect USB an try to re-flash.. It works for 30 minutes now without luck, I don't know what to do either... HELP!!
and a hint to those that are NEW: if you want to screw up your device, play with ROM upgrades... you will end up like us..

easycure1974 said:
Sorry, stupid me I was as easy as start in USB mode and reflash and it booted normally again
Click to expand...
Click to collapse
PLEASE help me, what utility did you use to reflash?

Just press the camerabutton and reset and then you will come to the USB mode and then just used the flash utility file again and start the flash again and then it shall work.
I used the RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe form the ftp once again and it worked

easycure1974 said:
Just press the camerabutton and reset and then you will come to the USB mode and then just used the flash utility file again and start the flash again and then it shall work.
I used the RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe form the ftp once again and it worked
Click to expand...
Click to collapse
doesn't work form me because I didn't unlock before it crashed.. now I can't re-flash it..

ok, but then use the right official flash for your device - if it is a qtek use a qtek flash or imate if it is an imate device. The most flash files is available on the ftp.

easycure1974 said:
ok, but then use the right official flash for your device - if it is a qtek use a qtek flash or imate if it is an imate device. The most flash files is available on the ftp.
Click to expand...
Click to collapse
10x easycure, you are an easy cure for my troubles I am downloading it and I am sure it will work this time ( have a QTEK 9100)
Another question: did RUU_Prodigy_1060204_105_11210_TMO_UK_Ship.exe upgrade your radio ROM as well? what machine do you own? I think of flashing it eventually as well..

I hope it will work for you!
Yes the t-mobile upgraded everything - but it has a lot of crap in the extended rom that I don´t like and with the new rom versions it doesn´t seem possible to delete anything from the extended rom.
So I will flash it again when a newer flash from qtek is available. Tried the Qtek_9100_1_6_7_ENG.zip rom but it is just OS - I dont like the idea of using OS from Qtek and the rest of the software from some other brand.
I have a swedish Qtek 9100

easycure,
I don't like the crap either but I found someone's suggestion to soft reset the device just before installing software from extended ROM (just after aligning screen). I just had to install some CAB's manually to get MMS support etc.
Hope this helps you also

Priit said:
easycure,
I don't like the crap either but I found someone's suggestion to soft reset the device just before installing software from extended ROM (just after aligning screen). I just had to install some CAB's manually to get MMS support etc.
Hope this helps you also
Click to expand...
Click to collapse
I tried that but I didn´t got the mms to work with that but then I shall make another try with that!

I installed Shortcut-MMS1-JAVA6XX-CV-VOICE-EmailWiz-TMO-03Nov05.CAB to get MMS support. I also installed coouple of CABs that had "Camera" in the name hoping it will improve camera functionality or something

Need help upgrading rom using ShellTool

Hello,
I have an O2 XDA Mini S (HTC Wizard) which is a G4 device running the latest 02 carrier rom. I tried to flash it with the latest version of the Dutch Qtek 9100 rom. I did everything what's in the manual, after a few minutes shelltool says Make a hard reset now. When I make the hard reset I still get the startup screen of my old rom. The language, applications and the themes of the Dutch Qtek 9100 are installed fine.
I installed the cab files and disabled the Radio module before flashing the rom. After it failed the first time I tried again but just the same

michielc said:
Hello,
I have an O2 XDA Mini S (HTC Wizard) which is a G4 device running the latest 02 carrier rom. I tried to flash it with the latest version of the Dutch Qtek 9100 rom. I did everything what's in the manual, after a few minutes shelltool says Make a hard reset now. When I make the hard reset I still get the startup screen of my old rom. The language, applications and the themes of the Dutch Qtek 9100 are installed fine.
I installed the cab files and disabled the Radio module before flashing the rom. After it failed the first time I tried again but just the same
Click to expand...
Click to collapse
Shelltool only flashes the OS part of the DOC chip, not the splashes...

mestrini said:
Shelltool only flashes the OS part of the DOC chip, not the splashes...
Click to expand...
Click to collapse
Is it possible to replace the splash screens with the screens of the rom that I'm trying to install on my Wizard ?

Dead Charmer... maybe

Hi all,
I tried to upgrade my MDA compact II (HTC Charmer) to WM6, but during the first step, downgrading to the "no vendor" version I made a mistake. A used a wrong version, it was for Prophet. After the final reboot, the device froze in the splashscreen "T-Mobile". After that I tried to do exactly the same with a "Charmer" version, but it didn't help me, the situation was the same.
However, now I'm able to flash successfully only the last vendor provided ROM update "RUU_Compact_ll_2060227_20602110_021921_T-MobileUK_Ship.exe", but it doesn't help me anyway, my Charmer is still freezing in the splashscreen. I tried to downgrade it , but the application gives the following error: "UPGRADE ONLY". When I try to make a hard-reset, and after that to confirm the factory settings by pressing "Yes" (green) button, the result is "Format FAT partition" and then "format is failed".
Only the bootloader is working now as well as the battery charging. Please, help me to turn back to the life my Charmer!
And one additional question: can I perform a CID unlocking just by ROM-flashing or the device must be fully operable?

Flash this:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
After that, you should be able to make hard reset. If you succeed, flash "RUU_Compact_ll_2060227_20602110_021921_T-MobileUK_Ship.exe" - that.

Hello there,
I am a new use an recently got an MDA PM200. I am in exactly the same situation as petrun. I have tried the flash suggested by vlodeck but it doesn't work, saying incorrect vendor ID (I guess that's because it's for a Prophet?).
What should I do next...?
Thanks.

OK, I succeed with a little progress. Many thanks to vlodeck, I will try to explain what happend...
I successfully flashed my Charmer with this Prophet ROM:
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
Full link:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
But it was possible only by using this "No ID" update application, not original one, maybe because my device is still locked:
Full link:
http://www.windowsceportal.hu/tartalom/programok/htc_charmer_upgradeut_noid.zip
After that I succeed to format the FAT partition (finally ). But I cannot after all to flash the latest official MDA compact II firmware. There is two possible events, which I experienced:
1. When I try to use the original flashing application, I get the following response: "UPGRADE ONLY".
2. When I try to flash the official MDA compact II ROM, but through the "No ID" application, I get "INVALID COMMAND".
Just for explication, now my device cannot boot, it freezes in the splashscreen (it is Qtek now, not T_Mobile...) and the following versions could be read:
IPL 2.06
SPL 2.20.0000
GSM 02.47.21
OS 2.20.7.34
So, how I can do that? What should I do further? I would like to unlock my Charmer, but should I firstly make it operable?
Thanks in advance for your help, guys!

By the way, all described above I tried sevetal times with the same result.
The other thing is that... all links about the CID unlocking downloads, which I found here are no longer active. Any alternatives?

Rise from the dead!
Incredibly, but it's a fact! After successfull FAT formating I probably didn't wait long enough. Today I turned on my Charmer and several seconds after the splashscreen "QTEK" it successffully booted in WM5, performed all settings and finally started to work!
It's GSM module works, the Bluetooth works, I am able to start different applications. Just the camera does not work. And the most strange thing for me is that this ROM was for Prophet, not for Charmer
So, after all, how to proceed to upgrade to WM6? Now the bootloader is above ver.2.
Should I firstly flash it with proper ROM (for Charmer) or it's not necessary?
Should I unlock it as is now (Prophet ROM)?
Vlodeck, I rely mostly on you, since the WM6 with Touch FLO is your creation.
Thanks!

You dont have to CID unlock. Just flash that WWE T-mobile WM5 AKU2 for Charmer. Good luck.

Maybe I am boring, but steel need an advice: I cannot flash "WWE T-mobile WM5 AKU2".
1. The original RUU gives me "UPGRADE ONLY", maybe because my SPL after flashing the Prophet ROM is 2.20
2. This "NO ID RUU":
http://www.windowsceportal.hu/tartalom/programok/htc_charmer_upgradeut_noid.zip
reaches 2% and gives "INVALID COMMAND", after that - only bootloader screen.
3. This "NO ID RUU":
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
cannot open the nk.nbf image (but works with other images), I don't know why.
What is the solution? Any ideas? Maybe some tool to downgrade the SPL to ver.1? I tried (it perhaps was bad idea)"RUU_Charmer_1120223_11202110_11220_T-MobileUK_Ship" and IPL became 1.12, but SPL remained 2.20... and Charmer didn't boot after that. After flashing the Prophet ROM it works again and IPL is 1.12, SPL is 2.20
In brief... how to flash successfully the last Charmer ROM?

If you cant flash the AKU 2 charmer rom, then go for AKU3.3 rom (can be german, that doesnt matter). Once done that, flash wm6.

Success
Yeah! Thanks to vlodeck now everitging is all right! I flashed the original German AKU3.3 ROM by using this RUU:
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
(The original one gives "INVALID VENDER ID", of course, in German ) After that - successfully upgrade to WM6 TouchFLO.
Briefly:
1. First try to flashing WM6 - crash! The reason: old bootloader version (IPL/SPL = 1.12).
2. Flashing the Prophet ROM - success for FAT formatting. The Charmer turned back to life.
3. Flashing the German AKU3.3 ROM from T-Mobile, but through the No ID RUU.
4. Upgrade to WM6 TouchFLO by vlodeck. At the begining I reached the same problem, as described here:
http://forum.xda-developers.com/showthread.php?t=331717
but after istalling cert_spcs.cab and enablerapi.cab in my device I succeed to finish the process.
Thanks vlodeck, good job! This ROM is really amazing!

petrun said:
Yeah! Thanks to vlodeck now everitging is all right! I flashed the original German AKU3.3 ROM by using this RUU:
http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
(The original one gives "INVALID VENDER ID", of course, in German ) After that - successfully upgrade to WM6 TouchFLO.
Briefly:
1. First try to flashing WM6 - crash! The reason: old bootloader version (IPL/SPL = 1.12).
2. Flashing the Prophet ROM - success for FAT formatting. The Charmer turned back to life.
3. Flashing the German AKU3.3 ROM from T-Mobile, but through the No ID RUU.
4. Upgrade to WM6 TouchFLO by vlodeck. At the begining I reached the same problem, as described here:
http://forum.xda-developers.com/showthread.php?t=331717
but after istalling cert_spcs.cab and enablerapi.cab in my device I succeed to finish the process.
Thanks vlodeck, good job! This ROM is really amazing!
Click to expand...
Click to collapse
WHERE I CAN GET BOUTH FILES cert_spcs.cab and enablerapi.cab
AND WHAT VIRSION OF PROPHET ROM SEND ME WORKING LINK THX DEAR

Charmer Stuck At Splash Screen
CHARMER STUCK AT SPLASH SCREEN
--------------------------------------------------------------------------------
I HAVE A MDA COMPACTII ''MADE IN TIWAN'' I WITCH WM5 I WANT TO UPGRADE IN TO WM6 SO I UPGRADE THIS WM6 TouchFLO Charmer WM6 ver. 2.1 FINAL by vlodeck AT THIS HOME PAGE http://forum.xda-developers.com/show...harmer+cert_sp... AFTER THIS I HARD RESET MY MDA C2 ITA ON BUT THE LANGUAGE IS NOT ENGLISH I CANNOT UNDERSTAND ....
SO I CAN REFLASH IT WITH THIS ROM Charmer_Touch_GER_Beta_2.7 .. AFTER FLASHING COMPLETE I SOFT RESET MY MOBILE.
SO MY MOBILE STUCK ON SPLASH SCREEEN ONLY T-MOBILE IS SHOW
MY MOBILE DETAIL IS AS UNDER
IPL 2.06 .0001
SPL 2.06 .0001
GSM 02.19.21
OS 4.0.0.0
PLZ DEAR SIR WHAT IS SOLUTION OF MY MDA C2
MDA2 CANNOT CONNECT WITH ACTIVE SYNC

Of course it cannot connect with ActiveSync, the device doesn't boot. One certain solution for bricked Charmer is Prophet ROM:
RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe
Use this link:
http://rapidshare.com/files/41754719/RUU_Prophet_220734_2207114_024721_QtekWWE_Ship.exe.html
In order to flash this, you should enter the bootloader, without using the ActiveSync. After that try to perform a hard reset, you probably will succeed to format the FAT partition.

if you cannot connect the pda to pc HOW CAN U PUT THE ABOVE PROPHET RUU ON CUREENT?

I have a charmer and I was trying to update to wm6. I can´t because the ipl is 1.12. I updated rom to german aku 3.3. But I can´t hard reset. format error. I´m trying to put prophet rom to format it, but when I send the prophet rom, it always give me an error at 95%. error 326 - this nbf file cannot be used fo your pda phone. please check your nbf file. the aku3.3 rom flashes ok. any idea?? I try tu send a radio rom. after that is the same. 95%error. please help. I can´t bring my charmerback to life.

Hello together,
I have the same problem like _mestre_.
I updated from T-Mobile AKU 3.3 GER to WM6 and flashed back to WM5 without problems, but when flashing again to WM6 from vlodeck my charmer didn't boot anymore and had that "Format is failed"-problem when making a hard reset. I could not recover my device until now with the method explained in this thread cause of the problems "error 326 - This nbf file cannot be used for your pda phone". So the Prophet Rom does not seem to work with boot loader 3.x. Has anyone any idea? Please help! Thank you very much in advance!

Yallah said:
Hello together,
I have the same problem like _mestre_.
I updated from T-Mobile AKU 3.3 GER to WM6 and flashed back to WM5 without problems, but when flashing again to WM6 from vlodeck my charmer didn't boot anymore and had that "Format is failed"-problem when making a hard reset. I could not recover my device until now with the method explained in this thread cause of the problems "error 326 - This nbf file cannot be used for your pda phone". So the Prophet Rom does not seem to work with boot loader 3.x. Has anyone any idea? Please help! Thank you very much in advance!
Click to expand...
Click to collapse
same problem here... any suggestions or is my charmer bricked?

Is my K-Jam totally bricked?

Is my K-Jam totally bricked?
It is now stuck up in bootloader screen.
I am able to swtch it off with power button. I can also have first flash screen.
On connecting with USB port, it shows yellow light indicating that it is charging & that over a period of time, goes green.
Earlier I had flashed TNT ROM but while reflashing newer it got stuck up as after flashing, I tried to hard reset [mistakenly thought ROM is flushed fully] & could not go further after initail first screen.
Other details:
IPL:2.16
SPL:2.16
GSM:02.07.10
O.S.:11.0.0.2
May some one help?
Thanks in advance.
Virat

Nopes ! its not 'Bricked' just had a bad flash. As long as it gets into bootloaders ,its perfectly safe. Perhaps,your phone is not CID unlocked ?
Download the official carrier's rom from its website and flash it in the bootloaders,it'll start to work fine.Then read the guide to cid unlock and upgrade.
Cheers!

boot issues
hi
i am having serious problems with my kjam.i installed black diamond's rom and now my phone boots upto the splash screen where it shows window mobile 6 and gets stuck there.
i have tried a soft spl, but it doesnt help as the phone cant connect or move from the splash screen.also, i can make call or do anything with the phone.
can someone assist me and also point me to a place where i can find the lastest tnt rom.

ghumanfly said:
hi
i am having serious problems with my kjam.i installed black diamond's rom and now my phone boots upto the splash screen where it shows window mobile 6 and gets stuck there.
i have tried a soft spl, but it doesnt help as the phone cant connect or move from the splash screen.also, i can make call or do anything with the phone.
can someone assist me and also point me to a place where i can find the lastest tnt rom.
Click to expand...
Click to collapse
Always post vital data of the phone,which is your device G3 or G4.Have you Tried Soft Reset or Hard Reset.it sometimes help.
Well,if it's a G3,is it SIM/CID unlocked,cuz its required to get the phone CID unlocked to upgrade to wm6,but if its a G4,then use method 'SoftSPL' or 'HardSPL' as it cannot be CID unlocked.
Post IPL/SPL...? of the phone here.
You can find all the latest wm6 Roms in 'Wizard Mobile 6' forum.
Cheers!

Thanks but solution found while reflashing in XP
Thanks for the reassurance Zabardast. I cold not even reflash it with vista but in xp, it sailed smooth. It is working normal now. Any way, thanks again for responding.
Virat

virat said:
Thanks for the reassurance Zabardast. I cold not even reflash it with vista but in xp, it sailed smooth. It is working normal now. Any way, thanks again for responding.
Virat
Click to expand...
Click to collapse
Thanks !
Glade you got it working
Have a nice day !

zabardast_1 said:
Always post vital data of the phone,which is your device G3 or G4.Have you Tried Soft Reset or Hard Reset.it sometimes help.
Well,if it's a G3,is it SIM/CID unlocked,cuz its required to get the phone CID unlocked to upgrade to wm6,but if its a G4,then use method 'SoftSPL' or 'HardSPL' as it cannot be CID unlocked.
Post IPL/SPL...? of the phone here.
You can find all the latest wm6 Roms in 'Wizard Mobile 6' forum.
Cheers!
Click to expand...
Click to collapse
Wireless Carrier
Vodacom
IPL - 2.16.0001
SPL - 2.16.0001
rom version - 2.16.9.1
radio - 02.07.10
extROM - 2.16.9.101
OS - WM5
Roms tried
BlackDiamond 3.1
i am running XP SP2 on my notebook.
i have restored the original WM5 rom however my screen is now fuzzy.

ghumanfly said:
Wireless Carrier
Vodacom
IPL - 2.16.0001
SPL - 2.16.0001
rom version - 2.16.9.1
radio - 02.07.10
extROM - 2.16.9.101
OS - WM5
Roms tried
BlackDiamond 3.1
i am running XP SP2 on my notebook.
i have restored the original WM5 rom however my screen is now fuzzy.
Click to expand...
Click to collapse
'Hard Reset' the phone,hope it'll work fine.
Well,I assume,you cudn't do the SoftSPL correctly the first time,try to apply the SpftSPL again correctly,if it works,ok,otherwise you can upgrade to wm6 with HardSPL method.

ba salam khedmate aghaye zebardast
duste aziz man ppc imate kjam daram ke eshtebahan soft spl kardam va rom wm6 prophet rush rikhtam ba tavajoh be inke seri gushi man g4 wizard bashe (ipl&spl 2.16.0001) kholase gushi alan tu safeye avali ke windows ba yek logo az rom marbuteh miad bala gir mikoneh .albateh 2 ta rom kjam asli wm5 ham gir avordam rikhtam vali hamunjuriye albateh jaye shokresh baghiye ke gushi tu halat bootloader gharar migireh va hard reset ham mishe. lotfan be man komak konid ta moshkelam ro hal konam. ba tashakor az shoma

could you please ,solve my problem kjam g4 wizard
laike salam brother
thank you very much for direction. I want to answer your question:
Quote:1. Which was the original official rom running on the phone before you tried to upgrade ?
1- I think wm5 belonge to 2005 becose it is written under the battrey.
Quote:2. What was the original wm5 rom and IPL/SPL of the phone before ?
2- I couldent remember but this phone approved by uaelab company [TA-2005/453 approved][E05/14/40225/g]and I flash with different official rom which you mentioned at ftp://ftp.clubimate.com but nothing happend ,maybe I do somthing wrong.
Quote:3.What exactly you mean you copied jumpspl to the root of the phone,did you applied SoftSPL ?
3- yes correct I did softspl with whit coulor screen then connected to pc and did toast that .
also I have problem to connect wst 4.2.2 to my ppc.
I download it and run, but the software couldent detect my fhone I dont know why .I connet it from bootloader 3coulor but nothing happen and so on.
could you please to explain how can I work with wst 4.2.2 also very important how to connect that because it says I have to connection with activesync .
pls direct me pls
mamnun
kourosh

New Official ROM Upgrade- Release Date: 2009-04-14

I've tried to download the ROM, but HTC tell me this "Sorry, this software download is not suitable for your device".
Maybe my device s/n number is not correct.
Maybe someone who has the correct s/n could download this ROM~
Just tell you guys the news~
http://www.htc.com/europe/SupportDownload.aspx?p_id=174&cat=2&dl_id=537
Caxio's and frednd's DownLoad Link--(I wanna say THANK YOU VERY MUCH!)
See page3 #21 & #23

Filename is :
HTC Touch 3G_MR2009_RUU_Jade_HTC_Europe_2.32.401.2_Radio_Sign_12.41.30.16_0.41.30.12_Ship
edit:
on booting the last red line (after radio and protocol) now says :
D 2.32.44800
Date (which shows after first boot) after screen calibration is now set to 25/03/09
(in settings / about) Build : 5.2.20771 (20771.1.4.6)
(in settings / device info) : rom version 2.32.401.2(44800)
ON customization after first boot if scaned for wifi networks and poped up a message about available networks

Ht845kh14923 :d

o2p63 said:
Ht845kh14923 :d
Click to expand...
Click to collapse
This is for italian version.

Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??

Downloading this know !!!
Will i be able to flash it to my device now i have used HardSPL ??

It seems HardSPL 1.40oli and this 2.32 rom don't work very well.Very sluggish and phone can't turn ON even after 2 Hard resets.
What is your experience???

Do not install if hard spl
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!

Could anyone check, if the gps-support has been improved?
km

lexx2009 said:
I installed the ROM upgrade from HTC, it ****ed up my device real bad: phone module not working, device boot up in aprox 1 min, after 3 mins Touch Flo not started, it restarts by itself.
I did hard reset and nothing happens.
I,m reinstalling jademan superrom!
I hope that works!
Click to expand...
Click to collapse
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
update : Jade is fine now. New SPL is 2.32.0000 . More testing to be done.
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?

lagoskon said:
Exactly same symptoms. I went to Stock SPL 1.40 and reflashing the new rom now. Hope it works better
Question : Can HardSPL 1.40.oli be flashed over new 2.32.0000 ?
Click to expand...
Click to collapse
How did you go back to Stock SPL 1.40 ?? Where can i find this ??

Myster said:
How did you go back to Stock SPL 1.40 ?? Where can i find this ??
Click to expand...
Click to collapse
This is on the Hard-SPL page along with the Oli version
http://forum.xda-developers.com/attachment.php?attachmentid=166262&d=1236988725

GPS seems to work fine now, also the scroll behavior of opera is better
km

It is annoying that hardspl doesnt work with this upgrade of jade.. can't built a rom now with the new oem. It's all newer than the iolite versions, but still doesnt include Footprint

Any changes in Manila? New tabs? Calendar? Stocks? Changes in the contacts?

Hi
What is the Radio version in this new ROM?
I have just applied the version from here and if this contains the old Radio then I can hold off for now until hopefully a compliant Hard-SPL is made, I can live without Opera being perfect.

Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please

nereus114 said:
Hi all,
I'm a new owner of a Jade since april 11. I'm french so excuse me for my english ^^'
I installed this new rom, and i get exactly the same problems as Lexx2009 and Lagoskon. I tryed to install the stock 1.40 rom but it doesnt work. I can synchronize the phone but i cannot use customRUU or hard spl anymore, it says the Jade isn't plugged with the usb cable ..
Please can anyone tell me what i have to do to get a rom whith works please
Click to expand...
Click to collapse
Install a different rom from this forum-> Shut down your jade, unplug it. Hold down "volume down button" and ""power on button" to get in to boot mode. now start to flash another rom.
when finished you can install stock spl and then install this new rom

Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel

jarel said:
Stupid (or not so stupid) question,
If we flash original SPL to instal this ROM, and SPL is upgraded by this ROM to 2.32,.... and HardSPL does not work with this new 2.23 SPL,.....
THEN, IT SEEMS THAT FOLLOWING THESE STEPS WILL ONLY MAKE US SLAVES OF THIS NEW & OFFICIAL HTC ROM!!!! i.e. No possibility of other ROMs flashing until new HardSPL is developed,...
Please, somebody to confirm this statement?
Thanks,
Jarel
Click to expand...
Click to collapse
that's right.. but i think it's in one of the drivers. using the old drivers and the new oem/sys makes it possible to run it with the current hardspl.
radio in this rom 0.41.30.12
no changes in manilla tabs, don't know what changed but it's newer