Installation stops when I reach 85% - 8125, K-JAM, P4300, MDA Vario Software Upgrading

I have tried to update my ROM on my QTEK 9100 to version 2.17.17. When I reach 85%, it stops and gives me an error message 326.
Any help would be EXTREAMLY appreciate!

msmobiles.com:
ERROR [320~328] : INVALID COMMAND
These errors seldom occur. However, if one of these errors occur, it could not be recovered and the device had to be sent back to the customer service center. In this case, you have to flash a new ROM code.
Click to expand...
Click to collapse

Thank you
Send it back for repair or flash a new ROM?

I've never encountered this error myself so I really doesn't understand exactly what it means... I would however try to reflash several other roms before sending it to a service center...
oh, can you get to bootloader mode by any chance? (pressing the two buttons on the right side and resetting the device). From there you should be able to flash a new rom.

I had the same problem... 95% and the Invalid command error. I was flashing the original Tmobile UK ROM. Now trying to flash another ones..

[email protected] said:
I have tried to update my ROM on my QTEK 9100 to version 2.17.17. When I reach 85%, it stops and gives me an error message 326.
Any help would be EXTREAMLY appreciate!
Click to expand...
Click to collapse
Try unlocking again if you did before.
--M

Related

Update Rom Failed

Hi,
I have a problem with my Wizard, my rom update failed because the pc reboots in the middle of the installation and now only the Red Green Blue screen appear with three things, IPL 2.17, SPL 2.17 and in the right top corner RUU.
I can't enter in the bootloader (pressing the camera button and turn on)
What can i do to fix this and update a new ROM?
Thanks in advance.
....... while on that screen plug in the usb cable and re-run the update utility.... Since the RBG screen is the bootloader...
I tried to do it, but i get ERROR[300] : INVALID UPDATE TOOL in the PDA Phone ROM Update Utility 2.00.1
Thanks
is working now. tks anyway
I'm having this same problem... not sure what's going wrong.
msmobiles.com:
Q: If I encounter ERROR [300] : INVALID UPDATE TOOL, what should I do?
A: This error message will appear when you use the incorrect RUU to upgrade. Please make sure you use the correct RUU version to upgrade.
Click to expand...
Click to collapse
Normally, you can only flash an official rom to restore from the point you are at. Once the bootloader is the only thing that comes up, a custom rom will not do the trick.
Once you have the official rom installed, you can then "cross-grade" to a custom rom.
_Nomad_ said:
msmobiles.com:
Click to expand...
Click to collapse
Ok, so using some Italian version is working for me. RUU is the same as the pda phone updater tool right? But something is still going wrong. It says I now have OS 2.26.10.2, which is the molski rom I've been trying to get on here, but neither the ipl or spl change, and the same cingular settings keep loading.
Man this is confusing me.
I have paid to unlock my g4, and I still can't get it to work the way I want it.

How to use HTC_Hermes_SIM_CID_Unlock_v3 on Breeze?

Hi All,
I am kindda newbie and have read almost all posts on how to superCID breeze, but haven't been able to do it so far.
I've heard that it is possible to use HTC_Hermes_SIM_CID_Unlock_v3 with Mteor. Can anyone tell me exactly what I have to modify in it so that it will not brick my device once I use it with my Breeze.
Thank you for your help,
Laurent
I recommend using http://www.imei-check.co.uk/ for your device. It only takes 3 minutes and cost no more then a bottle of wine.
After that your device is SuperCIDed and unlocked so every update process is very easy.
If you don't like to spend the money, you have to read a lot and you will get errors where you have to find a work around everytime you like to update or modify your device.
Does it mean that I will not have the very boring "INVALID VENDOR ID" error?
My phone is already unlocked and I can use any SIM card in it.
The problem I have is this annoying "INVALID VENDOR ID" that keep on coming whenever I try to upgrade my ROM. I've tried to rerun the same upgrade without disconnecting the cable and being in boot mode but it just keeps on coming.
Thank you for your help,
Laurent
laurentg said:
Does it mean that I will not have the very boring "INVALID VENDOR ID" error?
My phone is already unlocked and I can use any SIM card in it.
The problem I have is this annoying "INVALID VENDOR ID" that keep on coming whenever I try to upgrade my ROM. I've tried to rerun the same upgrade without disconnecting the cable and being in boot mode but it just keeps on coming.
Thank you for your help,
Laurent
Click to expand...
Click to collapse
You need to CID unlock your phone too ... make it superCID
there are already discussed ways of doing it, just do a liitle search.
bR

Phone locked in bootleader!! Cannot even Hard Reset!!

Hi,
I wanted to update my trinity in the version of S300+ (French) with the original HTC ROM.
Not only it didn't work, but I lost my phone, I cannot access anything even with Hard Reset and battery removal...
When I want to upgrade, it's going till 1% and then it stops and I'm getting a message "Error 286" Cannot connect with phone.
I cannot hard reset, I cannot do anything! When I hard reset, I'm always coming back to the bootloader (I think it's the bootloader, the screen with colors, where it says numbers and it's says USB).
Any idea? A upgrade with miniSD will help?
Thanks!
Start flash utility again and wait untill it starts again (can take sometime).
I had it to when I first flashed a rom.
Hi,
I tried it already, but it's always blocking at 1% of progress and it's telling me in the computer Error 286, and the phone resets and comes back to the bootloader...
Any idea?
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
This will solve all your problems:
http://forum.xda-developers.com/showthread.php?t=308691
sharedworld said:
I just tried now to update the ROM with the HTC_Trinity_SIM_CID_Unlock_v1, it's going till 14% but then it stops...
Any idea, please?
I cannot send back my device to warantee because updating roms is forbidden...
Click to expand...
Click to collapse
Put the phone in BOOTLOADER, then disactive ACTIVESYNC (form menu). After then start MTTY (you found it in the forum) set it on USB and then give the command:
task 32 Enter
task 28 Enter
task 2A Enter
info 8 Enter
task 8 Enter
After the last command the PDA restart and then you make a normal flash.
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
qubit76 said:
I concur :
http://forum.xda-developers.com/showthread.php?t=308691
after 1/2 a day wasted on the agony of a my problem phonem I finally managed to get pof's sxpliot to work, and I promise, it does.....
Click to expand...
Click to collapse
Please give more instruction howto
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
biohazard said:
Can't you just reflash it with an original SFR ROM? And then read correctly all the instructions for the wm6 flash?
Click to expand...
Click to collapse
SFR dosen't give any ROM... But the problem is that I cannot get out the bootloader, but I'll use the solution given here.
Thanks!
sharedworld said:
SFR dosen't give any ROM... !
Click to expand...
Click to collapse
Looks there]...and flash again
shym said:
Looks there]...and flash again
Click to expand...
Click to collapse
It's a DUMP... And not a full one... For ex. you do not get the splash screens...

Stuck in Bootloader Mode /-> ERROR [264, 274] : CONNECTION

HELP ME OUT GUYS, IM TRYING TO FLASH THE WM6 ROM TO A CINGULAR 8125: IPL 2.25, SPL 2.25 AND SEEM TO BE STUCK IN BOOTLOADER MODE. I FIRST GOT AN UPDATE ERROR AT 99%, PERFORMED RECOVERY - AND GOT THE SAME ERROR AGAIN. NOW THE RUU WON'T EVEN START AND I GET ERROR 264 : CONNECTION ERROR. ACTIVE SYNC NO LONGER IS GREEN, ETC. I DOWNLOADED THE XDA MOBILE 6r2a.zip FROM THIS SITE. NOT SURE WHAT I DID WRONG. I THINK I NEED TO GET BACK TO AN ORIGINAL ROM AND START ALL OVER BUT NOT SURE WHERE I CAN FIND ONE. THANKS.
ditto
ensophalic said:
HELP ME OUT GUYS, IM TRYING TO FLASH THE WM6 ROM TO A CINGULAR 8125: IPL 2.25, SPL 2.25 AND SEEM TO BE STUCK IN BOOTLOADER MODE. I FIRST GOT AN UPDATE ERROR AT 99%, PERFORMED RECOVERY - AND GOT THE SAME ERROR AGAIN. NOW THE RUU WON'T EVEN START AND I GET ERROR 264 : CONNECTION ERROR. ACTIVE SYNC NO LONGER IS GREEN, ETC. I DOWNLOADED THE XDA MOBILE 6r2a.zip FROM THIS SITE. NOT SURE WHAT I DID WRONG. I THINK I NEED TO GET BACK TO AN ORIGINAL ROM AND START ALL OVER BUT NOT SURE WHERE I CAN FIND ONE. THANKS.
Click to expand...
Click to collapse
That was the same rom that toasted my Qtek 9100 and now I'm stuck at the 99% mark before I get update:[302] error. Sorry didn't mean to steal your thread m8 but when I aksed the forum if they could help me out I got zero response ...so mines a brick right now.
BTW: I've tried the Wizard Love ROM but that was spanish I think and comes up with "INVALIDO" or something similar. I've fully charged the battery, removed the SD card and disabled "allow USB connections" in activesync, along with killing off wcescomm.exe ...but still no joy. Hope you get sorted with yours soon.
Original ROM's are easy to find, just go to either your phone service providers website and it should be on there, or go to HTC's website and they'll either have it or have links to where you can get it. Before you tried flashing XM6r2a, did you CID unlock your phone? That may be your problem.
ADD+, your phones not a brick yet if you can get in to the bootloader, which since you said that you tried to flash the wizard love ROM I'm guessing you can still do. You should also re-flash the original ROM that was on there and see if you can at least get that one to load back on there.
Also, for Original ROM links try this link - http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
xeno1 said:
Original ROM's are easy to find, just go to either your phone service providers website and it should be on there, or go to HTC's website and they'll either have it or have links to where you can get it. Before you tried flashing XM6r2a, did you CID unlock your phone? That may be your problem.
ADD+, your phones not a brick yet if you can get in to the bootloader, which since you said that you tried to flash the wizard love ROM I'm guessing you can still do. You should also re-flash the original ROM that was on there and see if you can at least get that one to load back on there.
Also, for Original ROM links try this link - http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
Click to expand...
Click to collapse
Got mine fixed by using the Xda_MiniS_LaunchROM_v154102.exe from the link in the definitive guide sticky. So as they say RTFM!!

Error 246 Device not responding

I'd bought my htc p3600 pro (black, free from sim-lock & free from any carrier) from London.
As advised by TRINITYGUIDES.INFO site I tried to do HardSPL with all the three available HardSPL files, but of no avail.
When the HardSPL's progress bar comes(on pc) it gives a message on my phone " Enterbootloader.exe....This may harm your device...Do you want to continue.." I pressed yes & the process stopped & gave an error on pc "Error 246 Device not responding" & on phone screen showed the bootloader with
TRIN100
IPL-SSPL by Des
TRIN100
SPL-1.07.ds
I did soft reset on my p3600 & its working as usual with it original spl infos.
I want to put official WM6 SEA version(ROM+RADIO) on my phone...Please help.
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
wingnutLP said:
I too have the same message when I try to upgrade to hard spl as per teh guide here: http://trinityguides.info/index.php...ask=view&id=25&Itemid=66&limit=1&limitstart=2
Can anyone help? I have tried updating active synch... could there be anything else?
I have flashed my rom befroe to unlock the GPS but I now want to upgrade to WM6.
I guess the hard spl is a failsafe and I can skip this step?
Thanks
Click to expand...
Click to collapse
Search is great function
http://trinityguides.info/index.php?option=com_content&task=view&id=37&Itemid=67
wingnutLP said:
Sorry!
I am an idiot.
Thanks
Click to expand...
Click to collapse
sorry I tried a Google search on the error message and came up with this thread!
wingnutLP said:
sorry I tried a Google search on the error message and came up with this thread!
Click to expand...
Click to collapse
Search more...
With this link:
http://www.google.com/advanced_search?q=+site:http://forum.xda-developers.com&hl=en&lr=&as_qdr=all
if you search error 246 you will get the solution on 11th answer.
Search more...
Have the same [Error 246]! How can I definitly fix it?
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Some specifications....
Sorry.... I have a P3600 White with Olipro 1.20 and rom Elias 1.9 SE Lite...
Tompo81 said:
Hi,
first of all, sorry for my poor English. I try to explain my problem so good I can... I hope you can help me.
I have the "[Error 246] Device not responding" problem.
I have used a lot the "search"-function and I have found a lot of posts which propose the same solution "restart the Rom upgrade another time". Ok I did it and my PDA works very well, but now I would like to solve the problem radicaly... How can I solve this problem? Should I use SPLexploit (I have found the guide on trinityguides.info) and then reflash a Hard-Spl?
Thx a lot
ciao
Tompo
Click to expand...
Click to collapse
Before flash manually enter bootloader. After start the rom update utility. (As www.trinityguides.info suggest). You will not get error 246 any more
thanks for answer
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Tompo81 said:
Many thanks for anwser...but...
Is this the only solution? If is so, then everbody has this problem, isn't so?
Ciao
Tompo
Click to expand...
Click to collapse
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Ok, now I really understand
Ok, this is a very good anwser, short and clear... thanks...
Ciao
Tompo
fktsndr said:
www.trinityguide.info
Here is written to flash rom you should manually enter to bootoader. In this case, you will not have error 246.
Most of the people know this, so they have not this problem
Those who not manually enter bootloader can get error 246, and this way of flashing is not as safe as the manual bootloader way.
(because in this case you use the spl uploaded by RUU, not the hard-spl on the PDA)
Click to expand...
Click to collapse
When i connect my touch hd to pc in active sync mode, then shutdown device an run in bootloader (volume down and power button at same time) i get the tricolor screen and after a while i get the progress bar on my phone and on pc. But i stays on 0% and says 'update error' after a while.
please help
I Have the Same Problem the Status bar Freeze On 0% and nothing happened
Until the Update Error Message Displayed
Please Advice
Thank You
Note: I Have HTC Diamond2 (Topaz) Without Sim Louk
Hi Me has the trinity 3600 as a VPA GPS vodafone branding, and i get the same error message trying to run the bootloader and entering tricolor screen, ---> error 246 aber manually starting into bootlaoder and restatrting the romupdateutil.exe same error 260 no connention...
So you guys have a working version of the updating ?
And please remove all the links which are not working, linking a solve for the 246 problem, there are nomore links available...
thanks
Dome
I found a way to solve the problem 246 go in you mobile device, -->start -> settings-> connections ->USB to PC open this. Remove the hook @ Advanced networksettings activation! ---> click OK--> close
try again the bootloader etc, then on the tricolore reboot screen is shown USB in the lower white field and the bootloader can do its routine complete.
Have Fun with flashing the phones!
Testet with original German Vodafone available ROM " vpa_comp_gps_RUU_Trinity_VF_DE_1_23_162_4_6275_1_29_00_01_13000_108_Ship.exe "
testet with ZackMcRofls superfast german rom " RUU_Trinity_GER_1.23.162.2_GPS_v3f_by_ZakMcRofl "
testet with
" htcp3600_RUU_Trinity_HTC_GER_1-23-407-2_103_6275_1-38-00-11_108 "
First was Zack´s rom, 2nd. was Original Rom, 3. was Trinitys rom, after trxing all, i flashed Zacks Rom again, it was the best in my view.
Thank you verymuch, bb

Categories

Resources