Restore Original Hard-SPL - P3600 Software Upgrading

Hi at all,
I had uploaded on my P3600 olipro spl 1.30 but now I need to send my P3600 to laboratory for assistance. I need to restore the original SPL. Where can I download it?
thk a lot,
Dormone

You need to check the wiki and download the latest offical rom for your phone, then proceed to flash it via sspl which should then overwrite the ipl/spl/splashes/etc all back to stock for your carrier.

thks for reply,
I had download the last official rom from htc club updated 30-07-07 after upgrade I checked pressing power button + camera button + soft reset but olipro spl is still present.

You flashed it with the included updater in that case, you need to put the signed file into one of the other update packages we have at this site, those use sspl to "force" a update of the ipl/spl even when hard-spl is blocking it...

thanks a lot shadowmite,
I used sspl to force original upgrade. Now all is ok.
thanks again
bye
Dormone

dormone said:
thanks a lot shadowmite,
I used sspl to force original upgrade. Now all is ok.
thanks again
bye
Dormone
Click to expand...
Click to collapse
What sspl? The ruu modified?

I'm not expert but I had read this post http://forum.xda-developers.com/showthread.php?t=293632 after I copy the file sspl.exe in the pda and execute the file. follow i had upgrade the original rom and al was ok also the bootloader.
bye,
Dormone

Related

Application UNLOCK/SSPL/HARDSPL

!!! USE THIS GUIDE ONLY IF YOU KNOW WHAT YOU ARE DOING !!!
!! READ THE END OF THE GUIDE FIRST(Very Importnat)
Aplication Unlock - lets you run unsigned software
SSPL - Software Second Program Loader is a boot loader after IPL (Initial Program Loader) often seen on smart phones and PDA:s.
- Lets you flash any rom on the phone
SPL 1.09 http://rapidshare.com/files/106089565/MTeoR_-_EUR1.09SPL.rar.html
[B]official HTC ROMS[/B]
RUS
http://rapidshare.com/files/106091396/RUU_MTeoR_1.34.261.1_1.38.00.10_HTCRUS_SHIP.rar.html
UNLOCK TOOLS
http://rapidshare.com/files/105133496/Unlock_HTC.rar.html
1. Folder "1"
put the file "SP_AllowCertificateInstall.cab" into the temp folder on you mobile phone (use active sync)
to connect. Execute the cab file on your phone.
2.Folder "2"
make sure you are connected to the phone threw active sync. Now run "EnableRAPI.bat" it will say if
it has succeded.
3.Folder "3"
make sure you are connected to your mobile phone through active sync. Start "MobileRegisteryEditor.exe"
Now go to SPV_C600 than HKEY_LOCAL_MACHINE than Security than Policies than Policies
so that you are in HKEY_LOCAL_MACHINE\Security\Policies\Policies
Now dubble click 00001001 (the first one after (Default)) and change the value to 1
Now dubble click 00001005 (the second one after (Default)) and change the value to 40
4.Folder "4"
put the file "Cert.cab" into the temp folder on you mobile phone (use active sync)
to connect. Execute the cab file on your phone.
5.Folder "5"
install and run HTC Security Manager.msi
select Security Off
Wait
YOUR PHONE IS APPLICATION UNLOCKED
6. Restart the phone
press and hold CAMERA+POWER while powering
you should see spl version
NOTE THAT VERSION
PULL OUT THE BATTERY AND POWER THE PHONE
7.1 Try to flash wwe rom directy
if you have wwe use sspl 1.01 http://forum.xda-developers.com/attachment.php?attachmentid=38680&d=1178637546
WWE rom
http://rapidshare.com/files/106091341/RUU_MTeoR_1.34.251.1_1.38.00.10_HTCEUR_SHIP.rar.html
after this you need to begin from step 1 till you see spl 1.10
now you have SPL 1.10 and CID HTC__Z12
jump to step 8
7.2 If 7.1 does not work try
7.2.1.SPL 1.09 http://rapidshare.com/files/106089565/MTeoR_-_EUR1.09SPL.rar.html
now you have SPL 1.10 and CID HTC__A07
7.2.2.you need to run the RUS update
RUS
http://rapidshare.com/files/106091396/RUU_MTeoR_1.34.261.1_1.38.00.10_HTCRUS_SHIP.rar.html
after this you need to begin from step 1 till you see spl 1.10
jump to step 8
8.flash any rom
now to flash an rom use SSPL 77.7 http://rapidshare.com/files/106072098/SSPL.rar.html
Copy the coresponding SSPL to the ROOT of the PHONE not the SD-CARD
run SSPL on the phone and immediatly press CAMERA+POWER
YOU SHOULD SEE TRI-COLOR SCREEN displaying spl 77.7
This SPL is allowing you to flash latest radio
or to Flash any rom usin sspl 77.7
Run the update from the PC
VERY IMPORTANT
i found a way to installl hardspl
1. unplug phone from usb
2. take out the battery/put it back
3. enter bootloader (press camera+power)
4. check for spl if it sais 2.05 you can go further if not read the fisrt guide
5. enter in windows
6. extract and copy to device root http://rapidshare.com/files/138396463/breeze_HARDSPL.rar.html
7. copy to storage card root BREEIMG.NBH
8. it should say SPL-1.01
9. follow onscreen instruction for the update
10.enter in windows and delete BREEIMG.NBH from card
11.enter bootloader (press camera+power)
12.it should say spl 7.77
13.be happy now you have hardspl and you can flash any rom (without sspl)
BEST REGARDS
i don't know whats the problem with appunlocking... there are 5 Regkeys that have to be set,... it stands all in wiki
http://wiki.xda-developers.com/index.php?pagename=Breeze_Registry
Application Unlock
http://wiki.xda-developers.com/uploads/Policies.reg
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"00001017"=dword:00000090"00001005"=dword:00000028"00001001"=dword:00000001after doing this run SDAunlock app (google for it) or
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101b"=dword:00000001
Running unsigned Apps without confirmation!
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101a"=dword:1
GREATLY APPRECIATED! finally some good explainations. so let me get this straight,
SSPL = application unlock? (im asking this because i already have my phone app unlocked using SDA security unlock software)
i have a dopod 595 and,
my IPL is 0.90 (do i need to update this?)
SPL is 2.05 (so i need to use the SPL>1.09)
radio is 1.06.00.10 (do i need to update this?)
RIL is 2.002
do i need to update anything before i try your WM6.1? which is the latest versions (IPL,Radio) you would recommend and can you please provide the links too. also, will the forward facing video call camera work with your ROM?
from wiki, it looks like there is the Radio:1.38.00.10 Protocol:32.71.7020.12H RIL:2.002 SPL:1.10.0000 ROM, and other older Radio ROMs but with newer SPL. so in order to update my radio, do i need to flash the entire ROM into my phone, or can i just use a Radio ONLY rom updater?
Please bear with me, because i really do not want to brick my phone.
Admin, please make this thread sticky. cheers
alexnvidia said:
GREATLY APPRECIATED! finally some good explainations. so let me get this straight,
SSPL = application unlock? (im asking this because i already have my phone app unlocked using XDA unlock software)
i have a dopod 595 and,
my IPL is 0.90 (do i need to update this?)
SPL is 2.05 (so i need to use the SPL>1.09)
radio is 1.06.00.10 (do i need to update this?)
RIL is 2.002
do i need to update anything before i try your WM6.1? which is the latest versions (IPL,Radio) you would recommend and can you please provide the links too. also, will the forward facing video call camera work with your ROM?
from wiki, it looks like there is the Radio:1.38.00.10 Protocol:32.71.7020.12H RIL:2.002 SPL:1.10.0000 ROM, and other older Radio ROMs but with newer SPL. so in order to update my radio, do i need to flash the entire ROM into my phone, or can i just use a Radio ONLY rom updater?
Admin, please make this thread sticky. cheers
Click to expand...
Click to collapse
i had 2.05 spl
i flashed the 1.09 spl from first topic
i flashed the latest wwe rom
now i have 1.10 spl
radio 1.38 from oficial rom
app unlocked
sspl
flashed wm6.1
jerpelea said:
i had 2.05 spl
i flashed the 1.09 spl from first topic
i flashed the latest wwe rom
now i have 1.10 spl
radio 1.38 from oficial rom
app unlocked
sspl
flashed wm6.1
Click to expand...
Click to collapse
im going to flash to WWE now with this version : HTC MUI BREE100 1.34.251.1 1.38.00.10 32.71.7020.12H 15673.3.3.1 3.3.1 2.002 1.10.0000 , then update to your WM6.1.
am i doing the steps right?
OK, i've done all the steps you provided in post no.1 (great instructions by the way). problem, when i run SSPL on the root of the device, the screen close blank and nothing happens even though im still pressing the camera+power button. what should i do now?
OK, i've done all the steps you provided in post no.1 (great instructions by the way). problem, when i run SSPL on the root of the device, the screen goes blank and nothing happens even though im still pressing the camera+power button. i had to unplug the battery to restart the device. am i doing anything wrong here?
Update : Now i got it. i had to run the SPL link, not the SSPL.exe as written in the first post. must be a typo.
Update2 : Success!! flashed to WWE. now proceeding to your WM6.1!!
Update3 : Running WM6.1 B1 now! thanks jerpelea! you're the man!
Admins please make this thread sticky.
I have I-Mate SPJas. I have tried several unlock tools including HTC Unlock toll, resgistry edit, SDA Unlock....
My original SPL version was 2.05 and after I ran SPL file I had IPL=SPL by des and SPL=7......
I have also applied other methods and my phones seems to be application unlock. But when I try to upload a new rom the phone goes to blank. I could never prevent this condition.
Is there a way to update Imate SPJas to Win 6.1? Which ROM works?
caglar_altan said:
I have I-Mate SPJas. I have tried several unlock tools including HTC Unlock toll, resgistry edit, SDA Unlock....
My original SPL version was 2.05 and after I ran SPL file I had IPL=SPL by des and SPL=7......
I have also applied other methods and my phones seems to be application unlock. But when I try to upload a new rom the phone goes to blank. I could never prevent this condition.
Is there a way to update Imate SPJas to Win 6.1? Which ROM works?
Click to expand...
Click to collapse
all roms work
follow the guide and will work
rom
I have gone through all of the steps of ROM update.
When the rom update utility prepare for installing, after I press "ENTER" the device closes immediately and the connection with ActiveSync stops.
In three color screen I see:
IPL SSPL by des
SPL : 1.01
Enter
When I go through root directory and enter to SSPL.exe, the phone again shut down and I have to removE/install battery to start the phone.
Please help!!
caglar_altan said:
I have gone through all of the steps of ROM update.
When the rom update utility prepare for installing, after I press "ENTER" the device closes immediately and the connection with ActiveSync stops.
In three color screen I see:
IPL SSPL by des
SPL : 1.01
Enter
When I go through root directory and enter to SSPL.exe, the phone again shut down and I have to removE/install battery to start the phone.
Please help!!
Click to expand...
Click to collapse
Hi, I had the same issue. Try pressing camera & off' buttons AND Enter all together.
rom update
1- I have updated the current rom to origininal config by manufacturer's original ROM.
2- I applied HTC unlock tool..
3- My first attempt to update rom gave #262 error. Second attempt was succesful.
thanks.
futureshock said:
i don't know whats the problem with appunlocking... there are 5 Regkeys that have to be set,... it stands all in wiki
http://wiki.xda-developers.com/index.php?pagename=Breeze_Registry
Application Unlock
http://wiki.xda-developers.com/uploads/Policies.reg
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"00001017"=dword:00000090"00001005"=dword:00000028"00001001"=dword:00000001after doing this run SDAunlock app (google for it) or
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101b"=dword:00000001
Running unsigned Apps without confirmation!
add:
[HKEY_LOCAL_MACHINE\Security\Policies\Policies]"0000101a"=dword:1
Click to expand...
Click to collapse
there are 5 keys unless you have the official security configuration manager
that is setting the other keys for you
BR
HARDSPL
hy all
i found a way to flash hardspl to breeze
this will allow to flash any rom from any cid so that you will not break devices due to wrong cid
BR
is there anyway to hard spl without going into windows? my device is stuck at windows 2nd boot screen (windows mobile 5 logo)
jerpelea said:
hy all
i found a way to flash hardspl to breeze
this will allow to flash any rom from any cid so that you will not break devices due to wrong cid
BR
Click to expand...
Click to collapse
That sounds interesting..!
alexnvidia said:
is there anyway to hard spl without going into windows? my device is stuck at windows 2nd boot screen (windows mobile 5 logo)
Click to expand...
Click to collapse
no
you must get to windows
what is your current cid?
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine. then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
alexnvidia said:
i have a dopod 595 device, the breeze with forward facing video call camera, so it's a breeze 160. it's a Qtek_Z12 device and the region is WWE.
before you posted the new herm radio, i successfully updated to your beta WM6.1 using your unlocking SSPL guide. i never upgraded the SPL though. the original phone's IPL and SPL are IPL0.9 and SPL2.05.
so what i did was first to upgrade to the latest WWE 1.38 using your unlocking/SSPL guide, then upgrade to your WM6.1 beta. everything worked fine. i do notice that only the IPL has been upgraded, and the SPL remains 2.05. so i ignored it.
it was when you posted the new herm radio upgrade i then decided to update my SPL as well. so as per your instructions in the unlocking guide, i first unlock the phone (WM6.1), perform the SPL1.09 update. it was successful. phone booted up just fine. then i run the official WWE 1.38 (the same one i used before upgrading to WM6.1 beta). and this time i did not run the DES soft SPL ( i must have forgotten and thought the phone is unlocked anyway). the RUU started, and the flashing failed at 1% giving an invalid vendor ID error message (as expected because my phone is not superCID and i forgot to run DES SSPL). after this little incident, i canot boot my phone anymore.
so i tried to recover it using various methods. and i successfully flashed back the original WM5 WWE dopod 595 ROM by using the latest RUU from 1.38 with old WWE WM5 nbh. the flashing completed 100%, the phone reboots, and still stuck at the second boot screen. IPL has been downgraded to 0.9 and SPL remains 1.09.
this is what i get
iinfo 2
CID: Wait interpreter timeout
HTCSF kEØ(HTCE
Cmd>
Click to expand...
Click to collapse
you can not do anithing
your ipl does not know how to load spl1.09
send the phone to repair and flash hardspl when it returns
there are many people with your problem
till now we have found not found any solution
BR
my phone is out of warranty, so sending for repair will cost me a lot. we'lll keep our fingers crossed and hope you guys can find a solution for us soon. thank you
i think, SPL version is very confusing. 2.05 is older than 1.09?
Would be good to have compatibility list between SPL and IPL versions to not mess and brick device.
I guess i was lucky, because i updated my breeze to resently posted HardSPL (thanks to jerpelea) and device still alive.
I found that RUUUpdateUt.exe i've used for DES SoftSPL is not working with HardSPL anymore. It cost me a bunch of my nerves (no body mentioned this fact!). Again luckily i found that stock RUU upgrade utility works fine with HardSPL (i just removed all dialogs except first for convenient use).
Well, at last, now i don't need to flash stock firmware (with radio ROM update which is extremely dangerous) every time when one of my cooked ROM refuses to work normally.

help! WHO CAN HELP ME!

hi all! i have some problem about upgrade my phones SPL to 1.10? i have read jerpelea`s thread about upgrade SPL! but i dont know how to made it ! step7 !from that !i dont know! if i must download the WWE rom and upgrade my phone with this rom using the SSPL7.77? and then donwload the sofeware from" http://forum.xda-developers.com/attachment.php?attachmentid=38680&d=1178637546"! this sofeware include breezessplv1.nb ,spl.lnk ,SSPL.exe !whats the use for this .nb file? is it a SPL1.10 upgrade file? whether upgrade the SPL1.10 in my phone without PC? just copy breezessplv1.nb to my storage card and turn it to TRI-COLOR SCREEN to flash it ,right ?
stationalz said:
hi all! i have some problem about upgrade my phones SPL to 1.10? i have read jerpelea`s thread about upgrade SPL! but i dont know how to made it ! step7 !from that !i dont know! if i must download the WWE rom and upgrade my phone with this rom using the SSPL7.77? and then donwload the sofeware from" http://forum.xda-developers.com/attachment.php?attachmentid=38680&d=1178637546"! this sofeware include breezessplv1.nb ,spl.lnk ,SSPL.exe !whats the use for this .nb file? is it a SPL1.10 upgrade file? whether upgrade the SPL1.10 in my phone without PC? just copy breezessplv1.nb to my storage card and turn it to TRI-COLOR SCREEN to flash it ,right ?
Click to expand...
Click to collapse
just follow the guide
thanks jerpelea! follow guide? but from step 7 on ,i dont understand! could you tell me how to do after appunlock? if i must upgrade my phone with wwe for first, and then upgrade the phones spl to 1.10 with the breezessplv1.nb ?
stationalz said:
thanks jerpelea! follow guide? but from step 7 on ,i dont understand! could you tell me how to do after appunlock? if i must upgrade my phone with wwe for first, and then upgrade the phones spl to 1.10 with the breezessplv1.nb ?
Click to expand...
Click to collapse
copy the 3 files into the root of the phone and run spl.lnk
this is the software spl loader
is an modded spl that is loaded into ram permiting you to flash any CID
.nb is the actual spl
.exe is the loader
.lnk is an text file (open in notepad)
BR
thanks jerpelea !but which do the first? upgrading with the wwe or upgrading with this .nb file for first? you are a great man! you are very nice!
this nb file is loades every time you want to flash an new rom
this .nb is not flashed to the device is loaded from an functional phone
so i don't understand your question
just follow the guide
thanks! just copy these three files to my device and upgrade my phone with the wwe rom, right?
stationalz said:
thanks! just copy these three files to my device and upgrade my phone with the wwe rom, right?
Click to expand...
Click to collapse
yes
you got it
thank you! you are a kind man!

URGENT: flashing back to stock for warrenty - all gone wrong

hi
i've need some help urgently on this as the phone is being picked up in the morning and its currently going really bad
i had dutties 3.9 rom on, but i found a 1.19 orange rom in the wiki, so installed this.
however the display is very bad, and is only showing 16 colours so looks rubbish
I belive this is to do with the SPL
This is what i did:
1. put phone in bootloader mode (was displaying SPL 1.56)
2. ran blac_uspl.exe in USB mode which changed the SPL to 1.15 (USPL)
3. installed the rom
did i do something wrong?
any help VERY appreciated
Thanks
Did you tried to flash back your original SPL??
USPL is just a temporary patch of the SPL...
I think you have to flash back to SPL 1.15...
To check if you have the right version put phone in bootloader mode it should displaying SPL 1.15...
Read here http://forum.xda-developers.com/showthread.php?t=431217
D'rath
Ikkari said:
Did you tried to flash back your original SPL??
USPL is just a temporary patch of the SPL...
I think you have to flash back to SPL 1.15...
To check if you have the right version put phone in bootloader mode it should displaying SPL 1.15...
Click to expand...
Click to collapse
thats the problem
i dont know how?
D'rath said:
Read here http://forum.xda-developers.com/showthread.php?t=431217
D'rath
Click to expand...
Click to collapse
Thanks but thats for Hard SPL, where as i used USPL
or am i getting it all wrong?
D'rath said:
Read here http://forum.xda-developers.com/showthread.php?t=431217
D'rath
Click to expand...
Click to collapse
Just look in the first post under:
How to reflash Stock/Shipped SPL - STEP BY STEP - FOR WARRANTY REASONS ONLY!
very strange
its working now
just needed a hard reset!
thanks for your help
edit------------
scratch that, its displaying them stupid colours again
GREAT!
m.r.davies said:
Thanks but thats for Hard SPL, where as i used USPL
or am i getting it all wrong?
Click to expand...
Click to collapse
You are getting it wrong!
USPL is a temporary patch to allow you to flash a unauthorized ROM!
You have currently SPL 1.56 installed, but you need flash back stock SPL 1.15
Ikkari said:
You are getting it wrong!
USPL is a temporary patch to allow you to flash a unauthorized ROM!
You have currently SPL 1.56 installed, but you need flash back stock SPL 1.15
Click to expand...
Click to collapse
thanks
i understand the problem now
but the link that was posted talks about hard spl, and when it says about reverting the rom, it talks about using hard spl, which is where i'm getting confused
Could you clarify which steps i need to take as its still showing spl 1.54
thanks
m.r.davies said:
thanks
i understand the problem now
but the link that was posted talks about hard spl, and when it says about reverting the rom, it talks about using hard spl, which is where i'm getting confused
Could you clarify which steps i need to take as its still showing spl 1.54
thanks
Click to expand...
Click to collapse
go to http://forum.xda-developers.com/showthread.php?t=431217
view the very last part of first post. It teaches you EVERYTHING. I think the part that you confused is going from step3 to step4. Read carefully. =)
good luck.
m.r.davies said:
hi
i've need some help urgently on this as the phone is being picked up in the morning and its currently going really bad
i had dutties 3.9 rom on, but i found a 1.19 orange rom in the wiki, so installed this.
however the display is very bad, and is only showing 16 colours so looks rubbish
I belive this is to do with the SPL
This is what i did:
1. put phone in bootloader mode (was displaying SPL 1.56)
2. ran blac_uspl.exe in USB mode which changed the SPL to 1.15 (USPL)
3. installed the rom
did i do something wrong?
any help VERY appreciated
Thanks
Click to expand...
Click to collapse
1. dnload the stock spl from the said thread.
2. dnload the hspl 1.56 olinex wrapper
3. connect ur fone to pc in the bootloader mode.
4. run the hspl 1.56 olinex wrapper and do nothing to the onscreen utility.
5. wait fr the files to be xtracted in the window from where u ran the hspl wrapper.
6. replace the self extracted ruu_signed.nbh with the stock spl 1.15 that u downloaded.
7. continue with the ruu utility.
thats all thts needed..
ultimatepichu said:
go to http://forum.xda-developers.com/showthread.php?t=431217
view the very last part of first post. It teaches you EVERYTHING. I think the part that you confused is going from step3 to step4. Read carefully. =)
good luck.
Click to expand...
Click to collapse
Thanks
yes you're right, it solved my problem
the reason i didn't try in the first place was becuase the title said HARD SPL and i didn't want to mess it up as i used USPL
i used Restore_Stock_SPL_115.zip and swapped the nbh file after initilizing installation (after extraction) and it worked great
thanks for all your help guys!!!!!!
i really appreiciate it
My god, I was feeling your anguish while reading this topic until the end...
Black Antitoon said:
My god, I was feeling your anguish while reading this topic until the end...
Click to expand...
Click to collapse
I eventually went to bed at 2:30am
all sorted now and got my new phone!
woohoo

Can`t restore my SPL on xda diamond touch

Hi friends,
i can not restore my SPL. I use the XDA DIAMOND TOUCH
I use at the moment SPL 1.93 olinex
and now i must restore my SPL because i must repair it to o2.
First i have download a o2 Software, flash it via USB to my touch diamond.
Then i download Unsigned-Hard-SPL-Diamond-OliNex and copy into this folder stockSPL 1.37 and flash it.
But in the Bootloader it looks the same SPL 1.93 olinex...
Please help me what can i do?
best regards
oh now.... its worked
its called SPL-1.37.0000
IS THAT CORRECT NOW?
bugx said:
Hi friends,
i can not restore my SPL. I use the XDA DIAMOND TOUCH
I use at the moment SPL 1.93 olinex
and now i must restore my SPL because i must repair it to o2.
First i have download a o2 Software, flash it via USB to my touch diamond.
Then i download Unsigned-Hard-SPL-Diamond-OliNex and copy into this folder stockSPL 1.37 and flash it.
But in the Bootloader it looks the same SPL 1.93 olinex...
Please help me what can i do?
best regards
Click to expand...
Click to collapse
Follow ALL these instructions:
http://modmydiamond.info/index.php?option=com_content&task=view&id=17&Itemid=27

htc diamond touch 100 stops at 0% when tryn to flash hspl

htc diamond touch 100 stops at 0% when tryn to flash hspl
pls help me out.
dia100 64m
spl-1.37.00
microp-diam[led] v11
psoc-diam stage pvt v030
You shud try SSPL method first to pass the HSPL. search for the SSPL here.
ayyu3m said:
You shud try SSPL method first to pass the HSPL. search for the SSPL here.
Click to expand...
Click to collapse
where should i search 4 it
here. see the attachments. first download and do JUMP SPL (SSPL) and then flash ur HSPL or the one i have attached here (1.93)
Downgrade your radio to one below 1.02.xxxxx before hardspl flash
Hey all,
I would like to add one thing that helped me - I had the same issue:
- Restore to original (eventually branded) stock ROM (this is needed for branded versions, worked for me also with radios higher than 1.02.xx.xx)
- Then install Hard-SPL
- Then MTTY
- Then newly cooked ROM
Hope our support can help you
Greets from Switzerland
dominica said:
htc diamond touch 100 stops at 0% when tryn to flash hspl
pls help me out.
dia100 64m
spl-1.37.00
microp-diam[led] v11
psoc-diam stage pvt v030
Click to expand...
Click to collapse
i have the same problem like but my SPL ver is 2.03.0000
the problem is that i cant use jumpspl anymore because i first tried to flash the device using MTTY so i formated my device and now i cant access its internal memory...can someone give me a rom for SPL 2.03 or tell me how to change SPL from USB because i can enter only in bootloader
magicdave26 said:
Downgrade your radio to one below 1.02.xxxxx before hardspl flash
Click to expand...
Click to collapse
pls help me with the steps to downgrade
Christoph21x said:
Hey all,
I would like to add one thing that helped me - I had the same issue:
- Restore to original (eventually branded) stock ROM (this is needed for branded versions, worked for me also with radios higher than 1.02.xx.xx)
- Then install Hard-SPL
- Then MTTY
- Then newly cooked ROM
Hope our support can help you
Greets from Switzerland
Click to expand...
Click to collapse
can u give me the site to download this files
ayyu3m said:
here. see the attachments. first download and do JUMP SPL (SSPL) and then flash ur HSPL or the one i have attached here (1.93)
Click to expand...
Click to collapse
hi
write file jump and finish but error 260 for HSPL 1.93

Categories

Resources